Petroleum Engineering Commons^™

Mathematical Modelling And Optimisation Of The Reactor For The Esterification Process Of Safflower Oil With N-Butyl Alcohol, Sadritdin Makhamatdinovich Turabdjanov Academician, Hasan Sadriddin Ugli Fozilov, Ozoda Bakhronovna Axmedova, Sadriddin Fayzullayevich Fozilov

Technical science and innovation

This study addresses the mathematical modelling and optimisation of a reactor for the esterification of safflower oil with n-butyl alcohol. To improve process controllability and reduce the need for numerous pilot-scale trials, an ideal-mixing continuous stirred-tank reactor (CSTR) model was adopted. Incorporating reaction kinetics, the effect of contact time on the relative viscosity of the product mixture was analysed. The modelling results indicate that achieving an acceptable degree of feedstock conversion is difficult when a single ideal-mixing reactor is used. Therefore, a CSTR cascade was proposed, and the configuration with N = 2 reactors was selected as the most appropriate …

Gas Lift Valve Operation Under Elevated Pressure And Temperature Conditions, Pedro O. De Melo Flores

LSU Master's Theses

Gas lift valves are critical components in artificial lift systems, and their performance directly influences well unloading efficiency and long-term production. Current industry models used to correct valve opening and closing pressure for temperature rely on assumptions that have not been extensively validated against experimental data. This study experimentally investigates the opening and closing behavior of injection pressure-operated (IPO) gas lift valves under controlled elevated-temperature conditions. A load rate test bench was modified to include a heating system capable of maintaining valve temperatures up to 220°F. Five gas lift valve designs from multiple manufacturers were tested over a range of …

Assessing The Geomechanical Modelling Of Underground Reservoir For Co₂ Storage Trapping Mechanisms, Bonavian Hasiholan, Mohammed Ali Farea, Elhassan Mostafa Abdallah, Sami Abdelrahman M. Yagoub, Yasir Mukhtar

Mathematical Modelling and Numerical Simulation with Applications

Effective carbon dioxide (CO₂) storage is essential for mitigating climate change amid increasing global greenhouse gas emissions. This study investigates the influence of geomechanics on CO₂ storage performance within carbon capture and storage (CCS), focusing on structural, residual, and solubility trapping mechanisms using a fully coupled modeling framework. Two numerical models, with and without geomechanical effects, are developed to evaluate impacts on reservoir behavior, CO₂ migration, and trapping efficiency. Each mechanism is analyzed separately and within an integrated framework to assess their combined contributions. Results indicate that geomechanical coupling increases reservoir pressure, reduces CO₂ flow velocity, enhances migration control, and …

Approach Formula To Increase Energy Efficiency Of Internal Combustion Engines In The “Green Economy” And Impact On The Natural Ecosystem, Zakirjon Ergashevich Musabekov, Hilola Zokir Qizi Uralova, Sayyodbek Ilxomjon O‘G‘Li Abdullajonov

Technical science and innovation

This article discusses, analyzes, and proposes solutions for the role of internal combustion engines in forming a "green economy", as well as ways to replace or modernize them. The relationship between internal combustion engines and the "green economy," as well as their energy efficiency and impact on natural ecosystems, is a crucial and urgent issue. These engines primarily generate energy through the combustion of petroleum-based fuels such as gasoline and diesel. However, this process releases harmful gases into the atmosphere, contributing to environmental degradation. The green economy is an economic model designed to protect the environment, ensure the efficient management …

Application Of Digital Rock Physics And Machine Learning To Improve The Understanding Of Fluid Flow Behavior Through Porous Media, Md Irfan Khan

Mechanical Engineering Theses

Accurately estimating reservoir rock properties and understanding capillary trapping mechanisms are crucial for fluid storage and flow modeling in porous media, particularly for applications such as carbon dioxide sequestration (CCS) and underground hydrogen storage (UHS). This thesis presents a comprehensive workflow that combines machine learning techniques and pore-network modeling approach to predict petrophysical properties and assess the impact of microscopic pore structures on capillary trapping. In the first part, a convolutional neural network (CNN) framework is used to predict rock properties—such as porosity, throat area, and pore surface area—from micro-computed tomography (micro-CT) X-ray images. It has been observed that incorporating …

Inspection Planning Of Subsea Pipeline Using Risk-Based Inspection, Ni Luh Triska Adelia, Badrul Munir, Johny Wahyuadi Soedarsono

Journal of Materials Exploration and Findings

Pipelines are an important tool in oil and gas exploration. Pipeline is a transmission and liquid collection lines, including their accessories, which transport fluids from one plant to another. In transmission and collection process, there is a possibility of failure which can have minor to major impact on personnel injury, the environment and interrupt the business process. To maintain safety and to prevent accidents, the source and cause of failure needs to be calculated. Risk-based inspection (RBI) is a method that can be used to calculate the risk and determine the inspection planning both schedule and method, by combining the …

Cfd Study On Two-Phase Flow Patterns In A Pipe With 90º Elbow In Different Operating Conditions, Hagar Alm-Eldin Bastawissi, Mohammed Ahmed Khafagy, E. A. El Shenawy Prof. Dr., Ahmed M. Salem Dr

Journal of Engineering Research

Recently, CFD has offered a technological solution for modelling multi-phase flow in which we can make endless simulations with reduced expenses and effort in high accuracy results; we shall also mention that experimental studies have limitations for safety considerations when experimenting with flow in high temperature or pressure values or medium nature as in nuclear or chemical flows.In this paper, we used the ANSYS FLUENT CFD program to simulate the two-phase flow in a pipe to study the effect of attaching a 90-degree elbow fitting to the piping system, seeking to find out the change in the pattern and resulting …

A Review Of Dielectric Barrier Discharge Cold Atmospheric Plasma For Surface Sterilization And Decontamination, Kolawole Adesina, Ta Chun Lin, Yue-Wern Huang, Marek Locmelis, Daoru Frank Han

Biological Sciences Faculty Research & Creative Works

Numerous investigations have shown that non-equilibrium discharges at atmospheric pressure, also known as "cold atmospheric plasma" (CAP) are efficient to remove biological contaminants from surfaces of a variety of materials. Recently, CAP has quickly advanced as a technique for microbial cleaning, wound healing, and cancer therapy due to the chemical and biologically active radicals it produces, known collectively as reactive oxygen and nitrogen species (RONS). This article reviews studies pertaining to one of the atmospheric plasma sources known as Dielectric Barrier Discharge (DBD) which has been widely used to treat materials with microbes for sterilization, disinfection, and decontamination purposes. To …

Carbon Dioxide Gasification Of Biochar: A Study On Utilizing Captured Co2 To Mitigate Greenhouse Gas Emission And Improving Carbon Conversion Efficiency, Nnamdi Ofuani

College of Graduate Studies: Theses & Dissertations

With rapidly growing global economies and world population, fossil fuel continues to play a major role in meeting current energy demands. Carbon capture and storage (CCS) technologies have, hence, been implemented to reduce CO₂ emissions in the atmosphere. With the implementation of CCS technologies comes the need to utilize the captured CO₂. This research, therefore, proposes CO₂ gasification of biochar as a viable carbon utilization pathway. With captured CO₂ coming at various concentrations, there is a need to understand how CO₂ concentration affects biochar conversion to useful products. This study, therefore, evaluates the effects …

Investigation Of Operational Parameter Differences Between The Standard Ron Test Method And Knock-Limited Modern Spark-Ignition Engine Operation, Alexander Hoth

Dissertations, Master's Theses and Master's Reports

Octane numbers (ONs) are used worldwide to rate the knock propensity of gasoline-like fuels for spark-ignition engines, making ONs the leading indicator of fuel quality for commercial distribution. The ONs were established 90 years ago and have only received minor changes compared to significant advancements in modern engine operation and fuel composition. This has resulted in discrepancies between knock-limited modern engine operation and standard ON ratings. This dissertation used a standard CFR octane rating engine at Argonne National Laboratory that was instrumented with modern combustion research tools to investigate key differences between the Research Octane Number (RON) rating conditions and …

Investigations Of Performance And Emissions Of A Fischer-Tropsch Gtl Sustainable Aerospace Fuel With Lubricity Improver In A Compression Ignition Engine With Butanol Port Fuel Injection, James B. Willis

College of Graduate Studies: Theses & Dissertations

As there is increasing concern over emissions of traditional fossil fuels, as well as the future of continued reliance on this dwindling resource, it is becoming increasingly evident that alternative fuels are a necessity. This research investigates the use of a Fischer-Tropsch fuel from natural gas feedstocks, S8, in an internal combustion research engine with a common rail fuel injection system. This synthetic kerosene fuel has a high DCN of 62, indicating high affinity to autoignition compared to conventional pump diesel (ULSD) at 48 DCN. However, due to the process by which it is produced, this fuel lacks the necessary …

Experimental And Numerical Investigation Of Fluid Flow Behavior Through Fractured Wellbore Cement, Mahya Hatambeigi

Civil Engineering ETDs

Leakage from wellbores has been a major challenge in the energy industry, leading to groundwater contamination, reduced productivity, safety hazards, and increased operating costs. Cemented annulus fractures are a common type of leakage pathway in wellbores that can form due to various physical and chemical conditions. The number of wellbore leaks continues to increase globally, making it imperative to develop a better understanding of the complex mechanisms governing fluid flow through fractured wellbore cement. Understanding the behavior of fluid flow through a leaky cemented annulus is crucial for evaluating the leakage potential and risk assessments in wellbore systems, as well …

Investigations Of A Surrogate Fuel Based On Fischer-Tropsch Gtl And Ctl In Cvcc, Idi And Di Compression Ignition Engines, Amanda C. Weaver

College of Graduate Studies: Theses & Dissertations

With the increase in availability, feedstocks, and properties of alternative fuels, compatibility issues emerge between current engine platforms often requiring a limit on the blend percentage of alternative fuel in conventional fuel or alteration to the engine platform. Two key metrics were identified, autoignition quality and lubrication characteristics, as vital for the proper function of a compression ignition engine, and if the blend of alternative fuels matches these two criteria for the diesel standard, then the resulting blend percentage can be considered as a viable alternative for complete replacement of conventional petroleum ULSD. Autoignition quality was matched using blends S-8, …

Fundamentals Of Microgel Flooding And Nanoparticles-Stabilized Foams In Enhanced Oil Recovery, Shuaijun Li

Dissertations and Theses

For centuries oil has remained a critical energy source for human civilization. After years of extraction, many oil fields have reached or are reaching a decline stage of production, even though up to a half of the total crude oil reserves in these fields has not been recovered yet. One reason is due to the structural heterogeneity of the oil reservoirs—reservoirs may consist of regions of higher permeability with larger pore size and regions of lower permeability with smaller pore size. Displacing fluids tend to flow through large permeability zones only without reaching the oil trapped in low permeability region; …

Economic Feasibility Of Mixed Plastic Waste Pyrolysis Using Twin Reactor System In Northwest Arkansas, Carol Rogers, Patricia Means, Renato Gonzalez, Kaida Sheets, Hayden Townsend

Chemical Engineering Undergraduate Honors Theses

Plastic waste generation is increasing at an unsustainable rate while recycling solutions remain stagnant. As a chemical means of recycling, mixed plastic waste pyrolysis can generate synthetic oil appropriate for use as fuel in power generation from plastic waste that otherwise accumulates in landfills. With the scaling of a commercial plastic pyrolysis process in Northwest Arkansas (NWA) modeled after an operational sawdust pyrolysis unit in Huntsville, Arkansas, economic analysis resulted in 26.3% internal rate of return. Therefore, construction of a commercial mixed plastic-to-fuel pyrolysis plant is economically justified and should be pursued. To effectively implement the proposed design, NWA must …

An Improved Foam Modeling Technique And Its Application To Petroleum Drilling And Production Practice, Yanfang Wang

LSU Doctoral Dissertations

Foam is one of the most common used multiphase fluid in Underbalanced Drilling (UBD) and Managed Pressure Drilling (MPD). Because of its low density, high capacity of lifting and carrying cuttings, low cost and compatibility with formations, foam has become more superior than the conventional drilling mud when depleted reservoir pressure, severe lost circulation, or unstable borehole are encountered. In general, the success of foam applications rely on the understanding of the fundamentals of foam rheology in downhole conditions.

Foam rheology has been studied for decades. Conventional foam rheological models such as Power Law, Bingham Plastic, Herschel-Bulkley to explain foam …

Well Oiled Machine: Classifying Machinery Performance Reductions Using Work Order Data, Jacob Brionez, Amber Burnett, Cho Kim, Scott M. Whitney, Thomas N. Anderson, Sumeet Treehan

SMU Data Science Review

Work Order (WO) data from System Applications and Products in Data Processing (SAP) software contains valuable information about what WOs intend to accomplish. Using SAP work order data, with time-series machinery sensor data combined into the same dataset, provides an opportunity to optimize prediction models to increase performance. Ideally, WO data can be utilized to help predict machinery's anticipated performance and can help prioritize a WO among others based on the anticipated machinery performance. It is possible to identify anomalies in pump sensor data using the Isolation Forest algorithm as the method for anomaly detection. The relationship between the sensor …

The Desorption Kinetics Of Methane From Nonaqueous Fluids For Enhanced Well Control, James Lee Nielsen Jr.

LSU Master's Theses

The mass transfer of a dissolved gas evolving to return to the gaseous phase from a liquid is governed by many parameters. This process affects the development of an oil and gas well due to the possibility of gas contamination occurring from either an influx entering the wellbore, or drilling through gas-bearing formations. Once this dissolved hydrocarbon gas circulates up the wellbore, it will begin to evolve from solution and poses a potential risk to drilling equipment, the environment, and personnel at a drilling rig. Being able to predict the behavior of gas desorption based on a known set of …

Void Fraction Measurements In Large (0.3 M) Diameter Bubble Column Using Wire Mesh Sensor And Pressure Transducers- Effect Of Sparger, Afolabi Gabriel Ojo

Dissertations and Theses

The importance of the accurate temporal and spatial measurements of the two-phase flow parameters in bubble columns is very well known. The aim of this research work is to report the spatial measurements of the void fraction distribution in a 30 cm diameter cylindrical bubble column using Wire Mesh Sensor (WMS) tomography and Pressure Transducers. Pair of WMS sensors, with a 64×64 wire configuration of each sensor, were installed which are separated by a distance along the axis of the bubble column. Wire Mesh Sensors and PTs Data were collected for time-averaged and transient with a sampling frequency of 1000 …

Void Fraction Measurements In A Large (0.3 M) Diameter Bubble Column Using Wire Mesh Sensors And Pressure Transducers: Effect Of Spargers, Afolabi G. Ojo

Dissertations and Theses

The importance of the accurate temporal and spatial measurements of the two-phase flow parameters in bubble columns is very well known. The aim of this research work is to report the spatial measurements of the void fraction distribution in a 30 cm diameter cylindrical bubble column using Wire Mesh Sensor (WMS) tomography and Pressure Transducers. Pair of WMS sensors, with a 64×64 wire configuration of each sensor, were installed which are separated by a distance along the axis of the bubble column. Wire Mesh Sensors and PTs Data were collected for time-averaged and transient with a sampling frequency of 1000 …

An Analysis Of Common Drill Stem Vibration Models, Mohammed F. Al Dushaishi, Runar Nygaard, Daniel S. Stutts

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Excessive drill stem (DS) vibration while rotary drilling of oil and gas wells causes damages to drill bits and bottom hole assemblies (BHAs). In an attempt to mitigate DS vibrations, theoretical modeling of DS dynamics is used to predict severe vibration conditions. To construct the model, decisions have to be made on which beam theory to be used, how to implement forces acting on the DS, and the geometry of the DS. The objective of this paper is to emphasize the effect of these assumptions on DS vibration behavior under different, yet realistic, drilling conditions. The nonlinear equations of motion …

Numerical Analysis Of Flexural Slip During Viscoelastic Buckle Folding, Davi Rodrigues Damasceno

Masters Theses

"Flexural slip is considered to be an important folding mechanism contributing in the development of different folds such as chevron, and kink-band buckle folds. Various filed studies have provided a general conceptual and qualitative understanding of flexural slip. However, quantitative evidence of the importance of the flexural slip mechanism during fold evolution is sparse, as the actual amount of surface parallel displacement, and timing, is difficult to measure accurately, due to the lack of suitable strain markers.

In this study 2D finite element analysis is used to overcome these disadvantages and to simulate flexural slip during viscoelastic buckle folding. Variations …

Coalescence-Induced Jumping Of Droplet: Inertia And Viscosity Effects, Samaneh Farokhirad, Jeffrey F. Morris, Taehun Lee

Publications and Research

The problem of coalescence-induced self-propelled jumping of droplet is studied using three-dimensional numerical simulation. The focus is on the effect of inertia and in particular the effect of air density on the behavior of the merged droplet during jumping. A lattice Boltzmann method is used for two identical, static micro-droplets coalescing on a homogeneous substrate with contact angle ranging from 0◦ to 180◦. The results reveal that the effect of air density is significant on detachment of the merged droplet from the substrate at the later stage of the jumping process; the larger the air density, the larger the jumping …

A Circuit-Based Algorithm For Two-Phase Flow At The Pore Scale In Porous Media, Todd Dorethy

Open Access Theses & Dissertations

Models of two-phase flow in porous media are of practical interest in many fields of science and engineering such as in oil recovery and hydrology. For this class of problem, an immiscible fluid is injected into a single-phase, porous medium to evict its valuable, native fluid. Because the aim is to amass as much of the indigenous fluid as possible, models attempt to output reliable flow regime patterns depicting how well the invading fluid displaces the native fluid.

Flow regime patterns generally depend upon the geometry of the domain, stimulation at the boundaries, and properties of the invading and native …

Fatigue Of Drill Pipes Used In Horizontal Directional Drilling, Feibai Ma

Doctoral Dissertations

Fatigue is the most common cause of mini-HDD drill rod failure. It can occur at stress levels far below the normal operating stress in most drill stem components. Fatigue failures occur because the drill rod, after it has been forced into a curved path, undergoes a cyclic bending stress oscillating from tension to compression in concert with the other stress components caused by torque, thrust, or pullback.

When a rod breaks underground, there is considerable extra cost caused by the delay in “fishing” out the broken rod as well as the cost of replacing the rod. On the other hand, …

Simplifying Lubricants For Farm Machinery, R A. Platt

Journal of the Department of Agriculture, Western Australia, Series 4

All moving parts on machinery needs lubrication. With the rapid development in farm machinery and its attendant sophistifications, the stresses imposed on the lubricants have also increased.

This article looks at some of the changes in requirements and developments in lubricants available.

4th Annual Umr-Dnr Conference On Energy -- Entire Proceedings, University Of Missouri--Rolla

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

No abstract provided.

Front Matter, University Of Missouri--Rolla

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

No abstract provided.

Opening Remarks, Raymond L. Bisplinghoff

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

You are all extended the very warmest welcome to the University of Missouri-Rolla. This four day conference on energy, the second of its kind, is filled with papers and activities that should find some interest for almost everyone involved in energy activities. All of us on this campus want you to have a rewarding four days and to enjoy yourselves as well. It goes without saying that we stand ready to aid you in every way that is possible. I want to commend the organizers, particularly Dr. Derald Morgan, for his hard and dedicated work in putting the conference together.

Energy Conservation In Uniroyal, Inc., John C. Madigan

UMR-MEC Conference on Energy / UMR-DNR Conference on Energy

In the last year, rapid developments have led to the establishment of industry conservation goals and monitoring by the Department of Commerce and the Federal Energy Administration via the various industry associations.

Since 1972, Uniroyal has progressed more than half way toward the 1980 goal of 15% established for the rubber and chemical industries. This paper will describe details of the program with emphasis on new input, such as the computerized tracking method now in use.

Plant studies have provided an assessment of "base" loads vs. process loads, important when considering unit energy consumption. These vary, particularly with the climate …