Petroleum Engineering Commons^™

Fly Ash Proppant Developed For Hydraulic Fracturing, Raz Rzgar Haydar

Theses and Dissertations

Proppants are critical components in hydraulic fracturing, used to maintain fracture conductivity and enhance reservoir stimulation. In high-pressure and harsh reservoir environments, the use of high-strength proppants is essential to ensure well performance. Conventional proppants, being sand, ceramic, and sintered bauxite can be expensive, and their use often requires costly fracture fluids. This study investigates the possibility of utalizing fly ash geopolymers as a sustainable alternative that is also cost-effective for proppants manufacturing. Fly ash, a by-product from the combustion of coal and other materials, was explored as a base material for proppants, utilizing an alkaline solution as an activator …

Effect Of Ionic Strength On Gelation Time And Strength Of Amps-Based Polymer Gels, Maryam Sharifi Paroushi, Xuyang Tian, Baojun Bai, Thomas P. Schuman, Yin Zhang, Mingzhen Wei

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Polymer gel treatment has been widely applied for improving sweep efficiency and controlling excessive water and gas production. Their performance depends on gelation time and final gel strength. In most studies, brine salinity is used to describe the effect of formation water on gel behavior. However, changing salinity also changes ionic strength and ion composition at the same time. Because of this coupling, it is difficult to identify the mechanisms controlling gelation, which has led to inconsistent trends in the literature. Increasing salinity has been reported to either slow or accelerate gelation and to weaken or strengthen gels depending on …

Evaluation Of A Novel Re-Crosslinkable Preformed Particle Gel For Conformance Control In Ultra-High Temperature Reservoirs, Yanbo Liu, Tao Song, Caleb Kwasi Darko, Thomas P. Schuman, Mingzhen Wei, Baojun Bai

Chemistry Faculty Research & Creative Works

Preferential fluid flow remains a major challenge in subsurface energy production and gas storage operations, resulting in excessive water production in mature oil fields, reduced heat extraction in geothermal reservoirs, and low sweep and storage efficiency in CO₂-EOR projects. Polymer gels are widely used to mitigate high-permeability channels; however, conventional systems exhibit limited plugging efficiency and short lifetimes in ultra-high-temperature reservoirs due to poor thermal stability. This study presents a novel ultra-high-temperature-resistant preformed particle gel (UHT-PPG) developed for conformance control in reservoirs with temperatures of 150–275 °C and severe super-K or channeling problems. The material was evaluated in …

Evaluation Of Chromium-Crosslinked Amps-Hpam Copolymer Gels: Effects Of Key Parameters On Gelation Time And Strength, Maryam Sharifi Paroushi, Baojun Bai, Thomas P. Schuman, Yin Zhang, Mingzhen Wei

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Controlling CO₂ channeling in heterogeneous reservoirs remains a major challenge for both enhanced oil recovery (EOR) and secure geological storage. AMPS-HPAM copolymers exhibit high-temperature resistance and brine tolerance compared with conventional HPAM gels, making them well suited for the harsh environments associated with CO₂ injection. Chromium-based crosslinkers (CrAc and CrCl₃) were investigated because sulfonic acid groups in AMPS can coordinate with trivalent chromium ions, enabling dual ionic crosslinking and the formation of a robust gel network. While organic crosslinked AMPS-HPAM gels have been widely studied, the behavior of chromium-crosslinked AMPS-containing systems, particularly their gelation kinetics under …

Utilizing Coal For Mesophase Pitch-Based Carbon Fiber Production: Precursors, Processes, And Progress, Christina M. Thompson

Theses and Dissertations--Chemistry

Graphitic materials possess unique properties due to the unique combination of layered crystalline structure and carbon’s low atomic weight. High performance carbon fiber is one such example, displaying exceptional strength-to-weight ratios, stiffness, and thermal and chemical resistance. These properties render high performance carbon fiber a critical structural reinforcement material in the manufacture of composites across various industries, such as for automotive and aerospace applications. However, balancing fiber performance with precursor and processing costs remains a challenge. As alternative carbonaceous feedstocks are explored, coal has gained interest for utilization in graphitic products as a relatively abundant and low-cost source of aromatic …

Laboratory Investigation Of High-Temperature Preformed Particle Gels For Fluid Control In Granite Cores For Geothermal Applications, K. Caleb Darko, Yanbo Liu, Thomas P. Schuman, Mingzhen Wei, Baojun Bai

Chemistry Faculty Research & Creative Works

To understand the applicability of high-temperature preformed particle gel (HT-PPG) for control of short-circuiting in enhanced geothermal systems (EGSs), core flooding experiments were conducted on fractured granite cores under varying fracture widths, gel particle sizes and swelling ratios. Key parameters such as injection pressure, water breakthrough pressure, and residual resistance factor were measured to evaluate HT-PPG performance. The gel exhibited strong injectability, entering granite fractures at pressure gradients as low as 0.656 MPa/m; HT-PPG yields a superior sealing performance by significantly reducing the permeability; and dehydration occurs during HT-PPG propagation, with a dehydration ratio ranging from 4.71% to 11.36%. This …

Determining The Limitations Of Class F Fly Ash Compared To Class G Cement In Hydrocarbon Wells Application, Youssef Helmy

Theses and Dissertations

Cement is a material commonly used in multiple applications in different industries. Among the industries that uses cement is the oil and gas industry. API (American Petroleum Institute) Class G cement that is the most incorporated form of cement used in the cementation of oil and gas wells to provide several forms of protection and stabilization for the casings. However, Class G cement is contested in terms of efficiency, costs, and environmental awareness against Class F fly ash geopolymers by researchers. This research aims to explore the potential limitations that fly ash geopolymer might have for its use in the …

Experimental Evaluation Of A Recrosslinkable Co2-Resistant Micro-Sized Preformed Particle Gel For Co2 Sweep Efficiency Improvement In Reservoirs With Super-K Channels, Adel Alotibi, Tao Song, Ali Al Brahim, Baojun Bai, Thomas P. Schuman

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

A recross linkable CO₂-resistant branched preformed particle gel (CO₂-BRPPG) was developed for controlling CO₂ injection conformance, particularly in reservoirs with super-permeable channels. Previous work focused on a millimeter-sized CO₂-BRPPG in open fractures, but its performance in high-permeability channels with pore throat networks remained unexplored. This study used a sand pack model to evaluate a micro-sized CO₂-BRPPG under varying conditions of salinity, gel concentration, and pH. at ambient conditions, the equilibrium swelling ratio (ESR) of the gel reached 76 times its original size. This ratio decreased with increasing salinity but remained stable …

Inspection Planning Of Subsea Pipeline Using Risk-Based Inspection, Ni Luh Triska Adelia, Badrul Munir, Johny Wahyuadi Soedarsono

Journal of Materials Exploration and Findings

Pipelines are an important tool in oil and gas exploration. Pipeline is a transmission and liquid collection lines, including their accessories, which transport fluids from one plant to another. In transmission and collection process, there is a possibility of failure which can have minor to major impact on personnel injury, the environment and interrupt the business process. To maintain safety and to prevent accidents, the source and cause of failure needs to be calculated. Risk-based inspection (RBI) is a method that can be used to calculate the risk and determine the inspection planning both schedule and method, by combining the …

Novel Re-Crosslinkable Preformed Particle Gels (Rppg) For Parent- And Infill-Well-Fracture Interactions Mitigation, Xiaojing Ge, Adel Alotibi, Ahmed Al-Hlaichi, Yanbo Liu, Tao Song, Junchen Liu, Baojun Bai, Thomas P. Schuman

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Hydraulic fracturing treatments in unconventional infill (or "child") wells can be significantly affected by depletion from existing parent-well, resulting in asymmetrical fracture growth. These issues may lead to excessive load-water production, proppant deposition, casing deformation in the parent well, and unbalanced stimulation of infill wells. To mitigate these effects, various strategies have been proposed, including the use of far-field diverters in child wells and repressurization of parent wells. Additionally, an increasingly popular strategy involves injecting near-wellbore diverters to temporarily plug entry points into the parent wellbores during frac operations on infill wells. To achieve better application, a novel low-cost, self-degradable, …

Carbon Fibers From Athabasca Oil-Sand Asphaltenes, Blake Reardon

All Theses

Carbon fibers possess ultra-high specific strength and modulus. Therefore, the material is popular in aerospace, automotive, and sports industries. Approximately 95% of all carbon fibers are spun from a high-cost precursor, polyacrylonitrile (PAN). There is a need for a cheaper grade of carbon fiber for low-cost applications because about half of carbon fiber cost is associated with precursor cost. A promising alternative to the high-cost PAN precursor is petroleum-based asphaltene. Asphaltenes are highly aromatic and have a high carbon content but lack the purity of the PAN precursor. Processes like the molten- sodium desulfurization upgrading have been used to harvest …

Dual Crosslinked Poly(Acrylamide-Co-N-Vinylpyrrolidone) Microspheres With Re-Crosslinking Ability For Fossil Energy Recovery, Jingyang Pu, Baojun Bai, Jiaming Geng, Na Zhang, Thomas Schuman

Chemical and Biochemical Engineering Faculty Research & Creative Works

Microspheres have been proposed to be applied in controlling wastewater production for mature oilfields and migrating leakage for gas and nuclear waste storage. However, it remains challenging for stacked microspheres to maintain strong blocking ability in micron-sized small pores or fractures. in this study, a novel microsphere was developed with comprehensive properties including high deformability and long re-crosslinking time upon tunable swelling ratio for the applications. a dual covalent and physical crosslinking strategy was used to develop novel microspheres reinforced by a hydrogen bond (H-bond, between pyrrole ring and amide group) and coordination bond (between chromium acetate (CrAc) and carboxyl …

Solvent And Concentration Effects Governing The Hierarchical Organization Of Asphaltenes: A Small-Angle X-Ray Scattering Study, Hasan Rejoanur Rahman

Open Access Theses & Dissertations

Asphaltenes are a group of planar molecules found in crude oil and are prone to aggregation which often causes blockage of pipes along the oil production stream resulting a huge economic downside. In an effort to understand the hierarchical organization of asphaltene in different solvents and concentrations, the solution structure of various asphaltene solutions were studied using small-angle x-ray scattering (SAXS). Solvents were chosen based on miscibility maps. Such maps are generated on the critical value of the solubility parameter difference between asphaltenes or asphaltene components, and a range of solvents. The critical factors that affect asphaltene and asphaltene component …

Comparison Of Intrusive And Non-Intrusive Methods For Corrosion Monitoring Of Fuel Processing Systems, Armando Jacob Espinoza, Thomas Conner Field

Materials Engineering

This presentation contains an assessment of the best overall corrosion monitoring device, intrusive or non-intrusive, for use in the petrochemical industry. Corrosion in the petrochemical industry is a large issue because it causes a deterioration of pipe integrity in fuel processing systems. A reduction of pipe wall integrity due to corrosion could result in a leak or an explosion of fuel processing lines since those systems function at high pressures. The use of corrosion monitoring systems in the petrochemical industry helps to detect early signs of corrosion prior to failure so that proper maintenance can be performed to prevent catastrophe. …

Overview Of Co₂ Leakage Problems And Sealants For Co₂ Leakage Remediation, Shudai Peng

Masters Theses

"Excessive Carbon Dioxide (CO₂) emission has become a serious issue and caused lots of environmental problems. Carbon Capture and Storage (CCS) program has been developed to reduce the CO₂ content in the atmosphere. CO₂ storage has been targeted mainly on depleted oil or gas reservoirs and deep saline aquifers. However, leakage could occur through wellbores, cap rocks, formation faults, and fractures during and after CO₂ injection. To minimize the risk, different types of sealants have been investigated to prevent CO₂ leaks. The aim of this thesis is to provide a comprehensive review of the materials which could be used as …

An Investigation Of Borax For Sealing Inflow From Berea Sandstone, Tri-Tris Bao Nguyen

Masters Theses

"Well inflow control is a major challenge for the oil and gas industry. Erle Haliburton revolutionized well inflow control with his patent for cementing oil wells in 1921. Soon after, cement became the accepted material to establish well integrity and has been ever since. Cement is used in all phases of the well life cycle, and it is expected to hold indefinitely once set. Yet based on the nature of cement and the placement techniques, flow pathways may develop from improper cementing jobs or from cement degradation over time. Well integrity is especially crucial for wellbore plugging and abandonment, since …

Plasticized Polymer Coatings For Sh-Saw Sensors For High Sensitivity And Long-Term Monitoring Of Btex Analytes In Liquid Phase, Pintu Adhikari

Master's Theses (2009 -)

BTEX compounds (benzene, toluene, ethylbenzene, and xylene) are constituents of crude oil and hazardous to human health. Among them, benzene has the lowest maximum contaminant level for drinking water because of its carcinogenicity. Spills or leakage from underground storage tanks or hazardous waste sites can contaminate nearby groundwater with these volatile organic compounds. Therefore, it is very important to detect the presence of BTEX contamination as early as possible in order to start the remediation process and maintain a healthy environment. To develop an in-situ continuous monitoring sensor system, shear horizontal surface acoustic wave (SH-SAW) sensor devices are being investigated …

Bioluminescent Magnetic Nanoparticles As Potential Imaging Agents For Mammalian Spermatozoa, Erick Salvador Vasquez, Jean M. Feugang, Scott T. Willard, Peter L. Ryan, Keisha B. Walters

Chemical and Materials Engineering Faculty Publications

Background: Nanoparticles have emerged as key materials for developing applications in nanomedicine, nanobiotechnology, bioimaging and theranostics. Existing bioimaging technologies include bioluminescent resonance energy transfer-conjugated quantum dots (BRET-QDs). Despite the current use of BRET-QDs for bioimaging, there are strong concerns about QD nanocomposites containing cadmium which exhibits potential cellular toxicity.

Results: In this study, bioluminescent composites comprised of magnetic nanoparticles and firefly luciferase (Photinus pyralis) are examined as potential light-emitting agents for imaging, detection, and tracking mammalian spermatozoa. Characterization was carried out using infrared spectroscopy, TEM and cryo-TEM imaging, and ζ-potential measurements to demonstrate the successful preparation of these nanocomposites. Binding …

Transition States And Modeling For Co9s8/Mos2 Catalysis, Gabriel Angel Gonzalez

Open Access Theses & Dissertations

Transition state computational studies of the sulfur removal from dibenzothiophene (DBT) molecule have herein been performed considering the Co9S8/MoS2 interface existing on unsupported Co/MoS2 catalysts. The linear synchronous transit (LST) and quadratic synchronous transit (QST) methods integrated in a density functional theory (DFT) program such as Dmol3 were used for the calculations of energy barriers of the transition states. Three different configurations present on the Co9S8/MoS2 interface have been envisaged as possible catalytic sites: sulfur-sulfur (S, S) sites, and molybdenum-sulfur (Mo, S) and molybdenum-molybdenum (Mo, Mo) edge sites. This study revealed that the (Mo, Mo) edge site is the most …

Growth And Properties Of Carbon Microcoils And Nanocoils, Muneaki Hikita, Robyn Bradford, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

Various types of coiled carbon filaments have been synthesized using chemical vapor deposition and other methods. These carbon filaments exhibit unique electrical and mechanical properties due to their versatile shapes and structures. To form coiled shapes, different types of catalyst compositions and reactive gases have been explored. Generally, coiled carbon filaments are classified by coil diameter and shape (e.g., microcoil and nanocoil). In this review, coiled carbon filaments are classified into three growth mechanism categories:

(1) bidirectional double helical growth;

(2) bidirectional twisted growth; and

(3) tip single helical or twisted growth.

Next, their synthesis methods and hypothetical growth mechanisms …

Slow Release Of Ions From Internalized Silver Nanoparticles Modifies The Epidermal Growth Factor Signaling Response, Kristen K. Comfort, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

Due to their distinctive physiochemical properties, including a robust antibacterial activity and plasmonic capability, hundreds of consumer and medical products contain colloidal silver nanoparticles (AgNPs). However, even at sub-toxic dosages, AgNPs are able to disrupt cell functionality, through a yet unknown mechanism. Moreover, internalized AgNPs have the potential to prolong this disruption, even after the removal of excess particles. In the present study, we evaluated the impact, mechanism of action, and continual effects of 50 nm AgNP exposure on epidermal growth factor (EGF) signal transduction within a human keratinocyte (HaCaT) cell line. After AgNP expose, EGF signaling was initially obstructed …

Phase Transformations In Calcium Substituted Lanthanum Ferrite, Patrick M. Price

Boise State University Theses and Dissertations

Increasing world energy demands are still heavily dependent on fossil fuels. To meet these demands, crude oil is increasingly being extracted from remote locations where natural gas pipelines do not exist. It is not profitable for oil and gas companies to transport natural gas by ship or truck from these remote locations so it is combusted on site in the form of gas flares. Critics oppose this practice due to the environmental impact from pollution and carbon emissions created during the flaring process. Oil and gas companies are eager to find profitable ways to eliminate natural gas lines in order …

Less Is More: Long-Term In Vitro Exposure To Low Levels Of Silver Nanoparticles Provides New Insights For Nanomaterial Evaluation, Kristen K. Comfort, Laura K. Braydich-Stolle, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

In view of the vast number of new nanomaterials (NMs) that require testing and the constraints associated with animal models, the majority of studies to elucidate nanotoxicological effects have occurred in vitro, with limited correlation and applicability to in vivo systems and realistic, occupational exposure scenarios.

In this study, we developed and implemented a chronic in vitromodel coupled with lower, regulatory dosages in order to provide a more realistic assessment of NM-dependent consequences and illuminate the implications of long-term NM exposure. When keratinocytes were exposed to 50 nm silver nanoparticles (Ag-NPs), we determined that chronically dosed cells operated …

The Biological Impact Of Concurrent Exposure To Metallic Nanoparticles And A Static Magnetic Field, Kristen K. Comfort, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

The rapid advancement of technology has led to an exponential increase of both nanomaterial and magnetic field utilization in applications spanning a variety of sectors. While extensive work has focused on the impact of these two variables on biological systems independently, the existence of any synergistic effects following concurrent exposure has yet to be investigated. This study sought to ascertain the induced alterations to the stress and proliferation responses of the human adult low calcium, high temperature keratinocyte (HaCaT) cell line by the application of a static magnetic field (approximately 0.5 or 30 mT) in conjunction with either gold or …

Tannic Acid Coated Gold Nanorods Demonstrate A Distinctive Form Of Endosomal Uptake And Unique Distribution Within Cells, Emily A. Untener, Kristen K. Comfort, Elizabeth I. Maurer, Christin M. Grabinski, Donald A. Comfort, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

One of the primary challenges associated with nanoparticle-dependent biological applications is that endosomal entrapment in a physiological environment severely limits the desired targeting and functionality of the nanoconstructs. This study sought to overcome that challenge through a systematic approach of gold nanorod (GNR) functionalization: evaluating the influence of both aspect ratio and surface chemistry on targeted cellular internalization rates and preservation of particle integrity. Owing to their unique spectral properties and enhanced surface area, GNRs possess great potential for the advancement of nanobased delivery and imaging applications. However, their ability for efficient intracellular delivery while maintaining their specific physiochemical parameters …

Carbon Nanotubes Grown On Glass Fiber As A Strain Sensor For Real Time Structural Health Monitoring, Matthew Boehle, Qiong Jiang, Lingchuan Li, Alexandre Lagounov, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

In order to more effectively monitor the health of composite structures, a fuzzy fiber sensor has been developed. The fuzzy fiber is a bundle of glass fibers with carbon nanotubes or nanofibers (CNTs or CNFs) grown on the surface. The nanotube coating makes the fiber bundle conductive while the small conductive path increases sensitivity. The fuzzy fiber sensor can replace conventional metal foil strain gauges in composite applications. The electrical response of the sensor is monitored in real time to measure strain, vibration, cracking and delamination. Continuous monitoring provides instant notification of any problems. Implementation of this sensor network in …

Nitrogen And Hydrogen Plasma Treatments Of Multiwalled Carbon Nanotubes, John G. Jones, A. R. Waite, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

This article investigates plasma treatment of vertically aligned multiwall carbon nanotube (CNT) films in different plasma environments for modification of surface chemistry and morphology. The surfaces of the CNTs were functionalized with a pulsed dc plasma treatment, where the power was directly applied to the nanotube film in low pressure argon/nitrogen and argon/hydrogen backgrounds. Optical emission spectroscopy was used to detect atomic and molecular excitations in the gas mixtures as well as in pure gases in the vicinity of the CNT films. In situx-ray photoelectron spectroscopy was performed on the treated samples to examine CNT surface chemistry after treatment. …

Using Science, Engineering, And Education To Address Water Supply Challenges In The Highlands Of Guatemala, Andrew Curtis Elmore, William Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

The Guatemalan Highlands is a Popular Destination for Non-Government Organizations Interested in Performing Relief Projects. U.S.-Based Organizations Such as Rotary International, Engineers Without Borders, and Various Religious Organizations Travel to Guatemala to Conduct Humanitarian Activities Which May Be Effective for the Short Term, But It is Not Clear that the Efforts Have a Systematic Impact. Students and Faculty at the University of Missouri-Rolla Have Systematically Studied Water Supply Issues Including Undergraduate and Graduate Research Projects and Undergraduate Engineering Courses Such as International Capstone Design. Materials Engineers Have Been Involved in the Study of Ceramic-Based Water Treatment Devices. These Microfilters Have …

Signaling Pathways Activated By Interleukin-2 And Interluekin-4 Receptors Mediate T Lymphocyte Clonal Expansion, Kristen K. Comfort

Chemical and Materials Engineering Faculty Publications

Cells sense and respond to chemical and physical stimuli through signal transduction pathways, which mediate cell proliferation, differentiation, migration, and survival. The cytokines interleukin-2 (IL-2) and interleukin-4 (IL-4) are key regulators of the adaptive immune system, particularly influencing the clonal expansion and differentiation of T cells. At least in culture, both synergistic and antagonistic effects of IL-2 and IL-4 co-stimulation have been reported; the antagonism, when observed, is thought to arise from the utilization of a common subunit shared by IL-2 and IL-4 receptors. We have sought to characterize IL-2 and IL-4 signaling at the level of intracellular pathways activated …

Effect Of Plasma Flux Composition On The Nitriding Rate Of Stainless Steel, Christopher Muratore, Scott G. Walton, D. Leonhardt, Richard F. Fernsler, David D. Blackwell, R. A. Meger

Chemical and Materials Engineering Faculty Publications

The total ion flux and nitriding rate for stainless steel specimens exposed to a modulated electron beam generated argon-nitrogen plasma were measured as a function of distance from the electron beam axis. The total ion flux decreased linearly with distance, but the nitriding rate increased under certain conditions, contrary to other ion flux/nitriding rate comparisons published in the literature. Variation in ion flux composition with distance was explored with a mass spectrometer and energy analyzer as a possible explanation for the anomalous nitriding rate response to ion flux magnitude. A transition in ion flux composition from mostly N2 1 to …