Other Chemical Engineering Commons^™

Analysis Of Sessile Drop And Captive Bubble Contact Angle Measurements On Metallic And Hydrophobic Surfaces, Jack H. Darnell

Williams Honors College, Honors Research Projects

Contact angle measurements are widely used to characterize surface wettability and determine changes in surface energy, yet the choice of measurement technique can significantly influence the results. This study compares the sessile drop and captive bubble methods for measuring contact angles of sodium dodecyl sulfate (SDS) solutions on carbon steel, stainless steel, and a hydrophobic wafer. Additionally, the time‑dependent wetting behavior of water, SDS, polysorbate 20 (commercial name Tween 20), and rhamnolipids on a hydrophobic wafer was evaluated over a five‑minute period. Results show that the sessile drop method consistently produced higher contact angles than the captive bubble method on …

Upcycling Waste To Wealth: Cuo-Sio₂/Reduced Graphene Nanocomposite From Pomegranate Peels For One-Pot Low-Temperature Conversion Of Waste Oils Into Valuable Fatty Acid Monomers, Attia Attia, Shahenda Mahran Dr., Maria Centeno Prof., Basudeb Saha

Petroleum Engineering and Gas

and hence reduce the price of the fatty acid monomers. This study reports for the first time a novel, environmentally benign, highly active copper oxide-silica oxide/reduced graphene oxide (CuO-SiO2/RGO), heterogeneous nano-catalyst derived from waste pomegranate peels, for the one-pot, low-temperature synthesis of fatty acid monomers from high-acid-value waste vegetable oil (WVO). The synthesised nano-catalyst was extensively characterised using XRD, FT-IR, TEM, SEM, EDX and TGA-DTA. Further, it was utilised to synthesise fatty acidrich oleic phenoxypropyl acrylate (OPA) monomer from high acid value WVO via a single-step reaction.

Interfacial Phenomena Of Plastics: From Surface Modifications To Environmental Impacts, Kennedy Guillot

LSU Doctoral Dissertations

Plastic is a ubiquitous part of everyday life since its introduction in the previous century. Global production continues to exponentially increase, establishing plastics as one of the most dominant materials in modern manufacturing. Within the scope of academia, plastic is essential due to its low cost and sterility, particularly for minimizing contamination. Beyond the laboratory, plastic use spans numerous industries, and its use and disposal has since raised many environmental concerns. Once valued for its durability, plastics now pollute the environment in landfills and natural ecosystems. In recent decades, the consequences of this pollution have been investigated, yet the full …

Binary Solid/Liquid Equilibrium Of Mixtures Of Thermally Robust Salts And Molecular Compounds For Use As Heat Transfer Fluids, Jared Ridge Mathews

Poster Presentations

Fossil fuels, contributors to climate change that may bear catastrophic consequences, power the entire world. The human species is almost entirely dependent on fossil fuels for energy, but other sources of renewable and environmentally friendly energy must be developed. Concentrated solar power (CSP) is a promising source of renewable energy with hampered potential—better heat transfer fluids (HTFs) are needed for it to be economically feasible. Currently, the HTFs in industrial use are predominantly either synthetic oils or nitrate-based molten salts. Synthetic oils are only stable up to 400 °C, and molten salts often have high melting temperatures, making them prone …

Binary Solid/Liquid Equilibrium Of Mixtures Of Thermally Robust Salts And Molecular Compounds For Use As Heat Transfer Fluids, Jared Ridge Mathews

Honors Theses

Fossil fuels, contributors to climate change that may bear catastrophic consequences, power the entire world. The human species is almost entirely dependent on fossil fuels for energy, but other sources of renewable and environmentally friendly energy must be developed. Concentrated solar power (CSP) is a promising source of renewable energy with hampered potential—better heat transfer fluids (HTFs) are needed for it to be economically feasible. Currently, the HTFs in industrial use are predominantly either synthetic oils or nitrate-based molten salts. Synthetic oils are only stable up to 400 °C, and molten salts often have high melting temperatures, making them prone …

Effect Of Pre-Adsorbed Species On High-Pressure Adsorption Of Methane In Zeolite 5a Using Grand Canonical Monte Carlo (Gcmc) Simulations, Kanhamardi Lao, Brooks D. Rabideau

Shelby Hall Graduate Research Forum Posters

Natural gas upgrading, which removes impurities from methane (CH4), is essential for industrial applications, including liquefied natural gas (LNG) production and power generation, as well as for residential use. Removing non-hydrocarbon impurities such as carbon dioxide (CO2), nitrogen (N2), and water vapor (H2O), among others, along with separating heavier hydrocarbon gases from raw natural gas, is required to achieve high- purity methane and prevent pipeline corrosion. Zeolite 5A is a microporous aluminosilicate material with a pore size of approximately 5 Å, containing sodium and calcium cations that balance the framework’s negative charge. Its structure offers high thermal stability and a …

Thermophysical Properties Of Aqueous Amine Salts For Closed Air Cabin Revitalization, Mahmud R. Yusuf, Isabela Flores, Ben Hines, Li Hua Zhang, Seth Christa, Brooks D. Rabideau, Kevin West, Breanna Dobyns, James Davis

Shelby Hall Graduate Research Forum Posters

Carbon dioxide (CO2) capture plays a crucial role in closed cabin air revitalization, however current CO2 capture technologies pose several issues. Traditional amine solutions, such as monoethanolamine, are commonly used in CO2 capture on the International Space Station but face drawbacks including high volatility, thermal degradation, and unpleasant odor. To overcome these challenges, amine salt solutions have emerged as promising alternatives. Amine salt solutions have reduced environmental impact, lower corrosion potential, and improved CO2 loading capacity, making them a more efficient and sustainable replacement. Knowing these physical properties are critical for modeling and optimizing a scrubbing process that employs these …

Quantifying The Effectiveness Of Rhamnolipid As A Biocide: Assessing Comparability Of A Modified Solution, Rosemary Sterling

Williams Honors College, Honors Research Projects

The CO2 induced corrosion of carbon steel in oil and gas pipelines, exacerbated by sulfate-reducing bacteria (SRB), poses a serious threat to infrastructure. This study evaluates the effectiveness of rhamnolipid (RhL), a biosurfactant, as a corrosion inhibitor and potential SRB biocide in simulated pipeline environments. Using a Postgate-C Modified Produced Water Simulant, which demonstrated electrochemical behavior comparable to industry-standard solutions while sustaining SRB, corrosion trials were conducted with and without RhL. Mass loss and electrochemical data revealed that RhL significantly reduced corrosion rates—by 85% on average and up to 99% instantaneously in a 4-day trial. Visual and analytical results from …

Glycerol-Free Biodiesel Via Catalytic Interesterification: A Pathway To A Netzero Biodiesel Industry, Nessren Farrag, Omar Youssef Youssef, Esraa Khaled, Omar Aboelazayem

Chemical Engineering

Conventional biodiesel manufacturing uses alcohol as an acyl acceptor, resulting in glycerol as a side product. The increased demand for biodiesel has led to the production of a substantial surplus of glycerol, exceeding the market need. Consequently, glycerol is now being regarded as a byproduct, and in some cases, even as waste. The present study aims to suggest an economically viable and ecologically friendly approach for maintaining the viability of the biodiesel sector. This involves generating an alternative byproduct of higher value, rather than glycerol. Triacetin is produced through the interesterification of triglycerides with methyl acetate, and is a beneficial …

Constant-Ph Molecular Dynamics At Inorganic Interfaces: Adding A New Dimension To Simulations Of Interfacial Phenomena., Ted Kalbfleisch

Electronic Theses and Dissertations

This dissertation explores the application of novel molecular dynamics simulation methods to better understand complex systems, with a particular focus on silica materials and protein interactions. Silica materials, known for their versatile surface and solution chemistries, play critical roles in catalysis, chromatography, and wastewater treatment. Despite their widespread use, the molecular-level interactions between silica surfaces and their environments remain poorly understood. To address this knowledge gap, we employed λ-dynamics enabled constant pH molecular dynamics to dynamically model protonation and deprotonation events on silica surfaces. Traditional experimental techniques such as x-ray crystallography, NMR, and cryo-EM are inadequate for probing structures in …

Valorisation Of Water Hyacinth For Different Engineering Applications, Nessren Farrag, Zeinab Elbhnsawi, Omar Aboelazayem

Chemical Engineering

Nature has many elements that can be beneficial or harmful. One of these elements is water hyacinth (WH) which is an aquatic weed found in water bodies such as rivers and lakes and it has an invasive nature due to its rapid growth rate. On the contrary, water hyacinth, despite its classification as an invasive plant species, possesses a multitude of industrial and engineering applications, demonstrating substantial potential for valorisation into various products. Its versatile attributes and widespread availability render water hyacinth a viable resource for deployment across several sectors, including wastewater treatment, bioenergy generation, bioremediation, and sustainable agriculture. The …

Hydrodynamics Of Drops And Particles Driven By Marangoni And Diffusiophoretic Forces, Subramaniam Chembai Ganesh

Dissertations and Theses

This study investigates the hydrodynamics of particles and drops driven by forces generated by an asymmetrical physical and chemical surrounding environment. In the first part, a novel colloidal motor design driven by surface tension forces is proposed, utilizing an active Janus particle encapsulated in an immiscible liquid drop to form a compound drop/particle. Marangoni forces induced by asymmetric solute adsorption at the liquid-liquid interface of the drop propels the compound system. The propulsion speeds of the motor are analyzed for various relative sizes and configurations of the Janus particle and the encapsulating drop and the effects of varying the transport …

Molecular Understanding And Design Of Deep Eutectic Solvents And Proteins Using Computer Simulations And Machine Learning, Usman Lame Abbas

Theses and Dissertations--Chemical and Materials Engineering

Hydrophobic deep eutectic solvents (DESs) have emerged as excellent extractants. A major challenge is the lack of an efficient tool to discover DES candidates. Currently, the search relies heavily on the researchers’ intuition or a trial-and-error process, which leads to a low success rate or bypassing of promising candidates. DES performance depends on the heterogeneous hydrogen bond environment formed by multiple hydrogen bond donors and acceptors. Understanding this heterogeneous hydrogen bond environment can help develop principles for designing high performance DESs for extraction and other separation applications. This work investigates the structure and dynamics of hydrogen bonds in hydrophobic DESs …

The Fabrication Of Nearly Monodisperse Chiral And Achiral Plasmonic Nanostructures And Their Applications, Macayla J. Caso

LSU Doctoral Dissertations

An object is chiral when it holds no lines of symmetry. This quality naturally occurs in chemistry and biology. When an object is chiral it has a unique handedness and objects of opposite chirality are called enantiomers. The importance of handedness was brought to light in the 1960’s when a racemic mixture of thalidomide enantiomers was given to pregnant women. One enantiomer was able to treat morning sickness while the other caused severe birth defects. This case brought to light how enantiomers have unique properties from each other even though they are similar materials. With this knowledge chiral nanomaterials must …

Comparing Firocoxib And Meloxicam In The Application Of Microneedle Patch For Transdermal Drug Delivery, Ruohan Li

Chemical Engineering Undergraduate Honors Theses

This thesis compares the performance of meloxicam and firocoxib in the aspects of its physical characteristic, chemical compositions, and in-vitro performances for transdermal pain management microneedle patches on farm animals. The microneedle patches are composed of polyvinyl alcohol (PVA), type I collagen (COL), and chitosan (CHI) as base material that carries NSAIDs to achieve therapeutic purposes. Scanning electron microscopy (SEM) was utilized to observe the morphological and physical characteristics of the microneedle patches. Both meloxicam and firocoxib microneedle patches were successfully prepared using the methodology, with organized microneedle distribution and sizing. And Fourier transform infrared spectroscopy (FTIR) confirmed the chemical …

Response Of Cell Nuclei To Mechanical Strain In Synthetic Liquid Crystals, Sydnee Ehorn

Chemical Engineering Undergraduate Honors Theses

In this research project, induced mechanical stress on the cell nucleus via synthetic liquid crystals (LCs) was explored. Points of interest were the shape alterations and distortions of the nuclear envelope under strain, providing insight into the mechanics and stiffness of the cell nuclei. LCs are substances with structure and fluidity, and LCs in the nematic phase are aligned in a single direction without layers, inducing shear stress on inclusions. This study confirmed that an aqueous solution of 17.3 wt% disodium cromoglycate (DSCG) can successfully strain the nuclei of chicken red blood cells (RBCs) by examining the nuclear response to …

Detection Of Toxic Aldehydes In Aerosols Of Electronic Cigarettes., Ellie Bess Reed

Electronic Theses and Dissertations

Over the past decade, use of electronic cigarettes (e-cigarettes) has increased in the younger generations of the United States. With the broad range of flavors and devices distributed on the market, American youth are prime marketing targets for the e-cigarette industry. To create a more regulated market, research of this thesis has been conducted on newer generations of e-cigarette “MOD” devices to examine how e-cigarette battery power output and coil temperature, concentrations of propylene glycol and vegetable glycerin, added flavorings (strawberry, mango, and menthol), and the presence of nicotine affect generation of aerosol particles and aldehydes in aerosols emitted by …

Extraction Of Melanin From Black Knot Fungus: Optimization And Applications, Amara Davis

Williams Honors College, Honors Research Projects

The goal of this research project was to optimize the extraction of melanin from black knot fungus and to analyze possible applications of the extracted melanin. An extraction method that was previously created was examined for possible improvements. Improvements that were studied include the elimination of steps in the extraction process while obtaining the same quality of product, examining options for machinery that could be used to increase production rate when moved to a production plant setting, and optimize the concentrations of the raw materials that are used in the extraction for possible reduction of cost without compromising yield or …

Exploration Of The Sludge Biodiesel Pathway, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Wastewater sludge is an overlooked source of fat, oil, and grease (FOG) that could be converted into biodiesel. The United States produces about 8 million tons of sludge per year. The disposal cost for this amount of sludge is about 2 billion US dollars. The widespread availability and low cost of sludge compared to other biodiesel raw materials make it an economical choice for a renewable fuel. Using sludge as a raw material can produce 25 to 30 mg per gram of fatty acid methyl ester (FAME); the main component of biodiesel. Sludge biodiesel has the potential of transforming a …

The Extraction Of Waxes And Lipids From Sorghum Using Green And Renewable Solvents Followed By Conversion To Biofuels Using Gamma-Valerolactone Pretreatment, Marissa Gallmeyer

Dissertations, Master's Theses and Master's Reports

Plant matter contains waxes and lipids that can be extracted and used or sold as a value-added product prior to conversion of the remaining plant material to biofuels. Wax and lipid extraction of plant materials is currently performed using volatile, non-renewable hydrocarbons, primarily hexane, which is produced from fossil fuels and can pose a health and safety hazard. The purpose of this study is to compare the amount and characteristics of waxes extracted by hexane with those extracted using organic solvents that are less toxic and can be produced from renewable sources.

Sorghum samples were extracted separately with hexane, 2-methyltetrahydrofuran …

Fractionation And Characterization Of Extracted Lignin From Oil Palm Empty Fruit Bunch Using Synthesized Deep Eutectic Solvents, Tan Yee Tong

Student Works (2020-2029)

Deep eutectic solvent (DES), a new generation green solvent has been introduced as an alternative pretreatment solvent due to its ability for lignocellulosic biomass fractionation and lignin extraction. Numerous types of compounds can be adopted as DES constituents, which has resulted in abundant variation of DES with varying properties. Selection of the suitable chemical compound category is therefore essential for optimum DES performance. However, investigation on the performance comparison between the different DES categories is lacking. In addition, despite its widely acknowledged effectiveness in biomass fractionation, the properties of DES-fractionated biopolymers, especially lignin are not well understood. Hence, this project …

Next Generation Of Applications Of Metal-Organic Frameworks For Energy And Environmental Sustainability, Qian Liu

Graduate Theses, Dissertations, and Problem Reports (ETD)

My PhD work aimed at using Metal-organic frameworks (MOFs) for mitigating the environmental issues and energy crisis associated with anthropogenic activities. Specifically, we developed robust platforms and/ or systems using MOF as “scaffolds” to allow for model pollutant detection and CO₂ sequestration and benign transformation respectively.

First, I detailed how photocatalytic properties of 2,5-furandicarbocylic acid (FDCA) in its alone and its MOF- integrated form (MIL-160) were used for the first time for the reduction of Ag⁺ at room conditions. Such photocatalytic activities could then be used in user-designed hybrids (i.e., Ag/MIL-160) to form sensorial platforms for prevalent phenol …

Review Of Established And Emergent Methods For The Production Of C4 Olefins, James Matthew Koval

Graduate Theses, Dissertations, and Problem Reports (ETD)

Current production of C₄ olefins is dominated by naphtha cracking and butane dehydrogenation, but significant research interest is developing in alternate feedstocks due to an abundance of inexpensive natural gas and bioethanol. The current C₄ olefin production methods are costly, make use of already-depleted petroleum resources, and are often hazardous to workers, which forms the impetus for investigation into alternative methods and assessment of their viability as a future means of olefin production. Methods of natural gas conversion to higher order hydrocarbons are discussed, including Fischer-Tropsch synthesis and oxidative methane coupling, each of which could form the first …

Elucidating The Properties And Mechanism For Cellulose Dissolution In Tetrabutylphosphonium-Based Ionic Liquids Using High Concentrations Of Water, Brad Crawford

Graduate Theses, Dissertations, and Problem Reports (ETD)

The structural, transport, and thermodynamic properties related to cellulose dissolution by tetrabutylphosphonium chloride (TBPCl) and tetrabutylphosphonium hydroxide (TBPH)-water mixtures have been calculated via molecular dynamics simulations. For both ionic liquid (IL)-water solutions, water veins begin to form between the TBPs interlocking arms at 80 mol % water, opening a pathway for the diffusion of the anions, cations, and water. The water veins allow for a diffusion regime shift in the concentration region from 80 to 92.5 mol % water, providing a higher probability of solvent interaction with the dissolving cellulose strand. The hydrogen bonding was compared between small and large …

Iron-Containing Nanoparticles For The Treatment Of Chrionic Biofilm Infections In Cystic Fibrosis, Leisha M. A. Martin

Nanoscience and Microsystems ETDs

Cystic fibrosis (CF) is the most common genetic disease resulting in the morbidity and mortality of Caucasian children and adults worldwide. Due to a genetic mutation resulting in malfunction of the Cystic Fibrosis Transmembrane Conductance Regulator (CFTR) protein, CF patients produce highly viscous mucus in their respiratory tract. This leads to impairment of the mucociliary clearance of inhaled microbes. In addition to reduced microbial clearance, anoxic environmental conditions in the lungs promote biofilm-mode growth of the pathogenic bacterial species Pseudomonas aeruginosa. Chronic infections of P. aeruginosa begin in early childhood and typically persist until respiratory failure and death result. The …

Effects Of Hofmeister Ions On Transition Temperature Of Two Thermo-Responsive Polymers, Joshua Moser

Williams Honors College, Honors Research Projects

It was hypothesized that through the use of Hofmeister Ions, the lower critical solution temperature (LCST) of poly(vinyl methyl ether) (PVME) and poly(ethylene glycol)- poly(N-isopropylacrylamide) (PEG-b-pNIPAAm) block-copolymer could be controlled. Through literature searches and small lab experiments, our team found that there may be a connection between Hofmeister effects and phase transition of a thermo-responsive polymer. To try and prove this, the lab team decided to take four cations (Mg²⁺,Na⁺, Cs⁺, K⁺) in solution with the thermo-responsive polymers and compared their LCST to solutions of the thermo-responsive polymer in de-ionized …

Removal Of Carbamazepine From Drinking Water, Paola Marrero-Rivera, Adam Johnson, Jordan Alex Gadberry, Juan Rodriguez, Thomas Krumpolc, Zach Wiese

Chemical Engineering Undergraduate Honors Theses

Due to the increasing prevalence of prescription medication over the past few decades, pharmaceuticals have accumulated in various water sources. This has become a public health concern because many pharmaceuticals have limited research on the effects of chronic low-level exposure.One pharmaceutical of interest that has been detected in water sources is carbamazepine. Carbamazepine (CBZ) is a common pharmaceutical prescribed for the treatment of seizure disorders, neuropathic pain, and various psychological disorders. It’s mechanism of action is “sodium channel blocking,” which is the impairment of conduction of sodium ions in sodium channels. This, in effect, reduces nervous-system conductivity in key areas …

Comparing Stenotic Blood Flow In Three- And Two-Dimensional Arterial Renderings Using Computational Fluid Dynamics And Multiphase Mean Age Theory., Jacob S. Garza

Electronic Theses and Dissertations

Over one million invasive coronary angiography procedures are performed annually in patients who experience chest pain or are known to have coronary artery disease. The procedure is carried out to ascertain the degree of arterial blockage (stenosis) that hinders blood flow to the heart. A cardiologist performing the procedure determines the physiological degree of a stenosis by either visual estimation, which is routine practice, or by invasively measuring fractional flow reserve (FFR), which is the current gold standard that has been demonstrated to improve patient outcomes and temper the cost of healthcare. Nevertheless, FFR is performed in only 10–20% of …

Enzymatically Active Microspheres For Self-Propelled Colloidal Engines, Jungeun Park

Dissertations and Theses

Micro- and nano-motors have attracted numerous attentions from various scientific areas due to their potential applications. Most studies on self-propelled colloidal engines have exploited catalytic decomposition of hydrogen peroxide to drive the motor. Since the hydrogen peroxide is caustic, it is not suitable to use in biological applications, encouraging people to develop “greener” fuels. The aim of this research is to study a new transduction mechanism for self-propulsion not tied to hydrogen peroxide, and which can in particular be used with biological molecules as fuels. In this study, we focus on making particles with enzymatic activity which can effectively decompose …

Development Of A Simple Handheld Biosensor For Waterborne Pathogens, Bryce C. Jones

Chemical Engineering Undergraduate Honors Theses

Current methods of detecting waterborne pathogens involve testing strips which take 24-48 hours to yield results, or require expensive equipment in order to function. In minimalist environments, these two technologies are not always applicable to test water quality. With the emergence of a new method of PCR, named LAMP PCR, it is possible to quickly and accurately detect pathogen DNA in a water sample. In order to scale this technique into a simple device, the aspects of the reaction must be accommodated, and a visual detection method chosen. A handheld device which keeps the isothermal LAMP PCR stable for the …