Membrane Science Commons^™

The Effects Of Solution Condition On Virus Filtration Performance, Fnu Namila

Graduate Theses and Dissertations

Virus filtration is an integral part of the downstream purification of mammalian cell culture-derived biotherapeutics to assure the viral safety of the products. Virus filtration membranes remove viruses based on a size-exclusion mechanism. Commercial parvovirus filers possess unique membrane structure and are designed to remove smaller non-enveloped parvoviruses with size 18-26 nm. However, some filters face issues, such as pre-mature fouling, the decline of filtrate flux, and reduction in virus retention. This doctoral dissertation focused on identifying the factors that influence the filtrate flux and the virus retention capability of commercial virus filters. The effects of solution pH and ionic …

Investigation Of Electrospun Nanofibers For Separation Applications, Shu-Ting Chen

Graduate Theses and Dissertations

Electrospun membranes are an attractive alternative to flat sheet membranes as absorbent with numerous advantages like high porosity, large specific surface area and ease of functionalization. This doctoral dissertation focuses on fabricating novel polymeric membrane adsorbents for protein separations and ammonium ion removal. Three distinctly different preparation methods including UV-initiated polymerization, atom transfer radical polymerization, and mixed-matrix formation, have been employed to fabricate the electrospun membranes. Overall, this study aimed to develop electrospun membranes with excellent separation efficiency for application in protein purification and ammonium ion removal.

Chapter 2 details the stepwise development of weak anion exchange membranes and subsequent …

Optimizing Membrane Distillation With Solar Thermal Collectors, Andrew Mason, Ben Shulders, Siamak Nejati

UCARE: Research Products

With rising human populations, the demand for freshwater is an ever-growing problem. One emerging technology to combat this problem is membrane distillation (MD). MD has several advantages for water desalination including 100% rejection of solute (salt, heavy metals, etc.) and mergeability with other affordable energy sources (solar heat, electric resistance, etc.) However, at the moment the specific energy consumption (SEC) of MD is very high due to low water production rates and large energy inputs to heat water. In a solar‐assisted design for MD, the high cost of solar collectors (~$200/m2) inhibits the low cost of water production in comparison …

Alumina Ceramic Membrane Incorporated With Graphene Oxide Frameworks For Protein Recovery, Ishak Noor Fauziyah

Student Works (2020-2029)

Alumina ceramic membrane is undergoing rapid development and innovation for protein recovery process. However, the limitation of this membrane type is membrane fouling due to the deposition and adsorption of proteins on the surface and pore walls of the membranes. It is crucial to minimize membrane fouling by reducing interactions between protein and the membrane surface via surface modification technique. Thus, the main objective of this research is to develop an alumina membrane with enhanced antifouling property for protein recovery process. An alumina dope consisting of 57 wt.% alumina loading was used to fabricate two alumina membrane configurations; which are …

Nanohybrid Membrane Synthesis With Phosphorene Nanoparticles: A Study Of The Addition, Stability And Toxicity, Joyner Eke, Philip Alexander Mills, Jacob Ryan Page, Garrison P. Wright, Olga V. Tsyusko, Isabel C. Escobar

Center of Membrane Sciences Faculty Publications

Phosphorene is a promising candidate as a membrane material additive because of its inherent photocatalytic properties and electrical conductance which can help reduce fouling and improve membrane properties. The main objective of this study was to characterize structural and morphologic changes arising from the addition of phosphorene to polymeric membranes. Here, phosphorene was physically incorporated into a blend of polysulfone (PSf) and sulfonated poly ether ether ketone (SPEEK) doping solution. Protein and dye rejection studies were carried out to determine the permeability and selectivity of the membranes. Since loss of material additives during filtration processes is a challenge, the stability …

Probing Counterion Condensation Phenomena In Nanostructured Thin Film Block Copolymer And Random Copolymer Electrolytes, Qi Lei

LSU Doctoral Dissertations

This dissertation describes advanced metrology and molecular dynamics simulations for quantifying counterion condensation in block copolymer electrolyte thin films. The fraction of condensed counterions (f_c) were quantified in nanostructured block copolymer electrolyte (BCE) and random copolymer electrolyte (RCE) thin films with new and established experimental techniques. The transition between the osmotic-controlled regime and condensation-controlled regime in BCEs and RCEs was identified using solution uptake measurements via a quartz crystal microbalance (QCM) and environmental grazing incidence small-angle x-ray scattering (GI-SAXS). The activity coefficients of ions in thin film were quantified experimentally and these values matched predictions from Manning’s Theory …

Toxicant Disruption Of Immune Defenses Potential Implications For Fetal Membranes And Pregnancy, Sean M. Harris, Erica Boldenow, Steven E. Domino, Rita Loch-Caruso

University Faculty Publications and Creative Works

In addition to providing a physical compartment for gestation, the fetal membranes (FM) are an active immunological barrier that provides defense against pathogenic microorganisms that ascend the gravid reproductive tract. Pathogenic infection of the gestational tissues (FM and placenta) is a leading known cause of preterm birth (PTB). Some environmental toxicants decrease the capacity for organisms to mount an immune defense against pathogens. For example, the immunosuppressive effects of the widespread environmental contaminant trichloroethylene (TCE) are documented for lung infection with Streptococcus zooepidemicus. Group B Streptococcus (GBS; Streptococcus agalactiae) is a bacterial pathogen that is frequently found in the female …

Engineering Ionomer Materials For Addressing Ohmic Resistances In Electrochemical Desalination And Waste Heat Recovery, Varada Menon Palakkal

LSU Doctoral Dissertations

Water scarcity and energy availability present important challenges that need to be addressed in the coming centuries. In the front of water technologies, desalting brackish water is of extreme importance for thermal electric power plants, chemical manufacturing plants, and other industrial operations that treat and reuse their water utilities. Membrane capacitive deionization (MCDI) is an energy efficient desalination technique that has drawn attention from commercial entities. Most material research studies on MCDI focus on enhancing electrode performance while little emphasis is given to rationale design of ion-exchange membranes (IEMs). In this work, the ionic conductivity, permselectivity, and thickness for three …

Analysis Of Blood Purification Studies On Oxone Mediated Tempo-Oxidized Nano Cellulose Mixed-Matrix Membranes, Tony Roller

Biomedical Engineering Undergraduate Honors Theses

End-stage renal disease (ESRD) is currently the ninth leading cause of death in the United States, and of the 661,00 Americans diagnosed with ESRD, approximately 468,800 were on hemodialysis in 2016. Hemodialysis refers to a technique where a machine combined with a membrane, often referred to as an artificial kidney, is used to clean blood by removing any waste such as urea, potassium, and other smaller waste products while preserving the concentrations and integrity of cells and proteins in the blood. It has been shown in artificial blood studies that cellulose nanomaterials, like TEMPO/Oxidized cellulose nanoparticles (TOCNs), can be integrated …

Characterization Of Oxone Mediated Tempo-Oxidized Nano Cellulose Mixed-Matrix Membranes During Ultrafiltration And Hemodialysis, Kristyn Robling

Biomedical Engineering Undergraduate Honors Theses

The ninth leading cause of death in the United States is kidney disease, and hemodialysis is the process most commonly prescribed for treatment. It utilizes a selectively permeable membrane filter to remove toxins such as urea from the blood and retain necessary protein levels. However, traditional filters, such as cellulose triacetate, used during dialysis can be inefficient in terms of separation performance and reduction of fouling. Recent exploration of nanoparticles has resulted in the creation of Oxone Mediated TEMPO-Oxidized Nano Cellulose which has properties that are believed to increase hydrophilicity, increase tensile capacity, decrease membrane resistance and lower fouling, making …

Scale-Up Of Polyaniline Cellulose Membranes, Isaac Bodemann

Chemical Engineering Undergraduate Honors Theses

Polyaniline coated cellulose membranes show impressive conductive properties that may be used to innovate traditional charged separation techniques, such as electrodeionization. However, these membranes are not sold to consumers, so they cannot be easily integrated into such systems. This research focuses on the scale-up and development of positively charged anion exchange membranes to be used in EDI cells. Novel cellulose membranes were made using lab-specific cellulose. These membranes were then coated using a polyaniline technique adopted from a paper titled, “Flexible Electrically Conductive Nanocomposite Membrane Based on Bacterial Cellulose and Polyaniline." This paper details the methods used to add the …

Peptoid And Antibody-Based Gfp Sensors, Solomon Isu

Graduate Theses and Dissertations

In this work, we have made and characterized a pair of immunobiosensors for detecting the green fluorescent protein (GFP) in an aqueous matrix. An anti-GFP antibody-based biosensor was assembled to detect GFP, while a novel peptoid (N-substituted oligomers of glycine designated as IOS-1) biosensor was also assembled for GFP detection. A quartz crystal microbalance (QCM) gold sensor was used as the supporting substrate for self-assembly of the immunobiosensors. Gravimetric measurements of the QCM gold sensor during immunobiosensor construction and operation were available in real-time using a QCM instrument. X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and Fluorescence microscopy were used …

Pollution Prevention Via Recovery Of Cerium (Iv) Oxide In Optics Company, Eugene Park, William Gallagher, Sydor Optics, Flint Creek Resources

Articles

Pollution prevention methods were applied at an optics manufacturer in an effort to improve recovery of a valuable polishing component, cerium oxide (ceria), 77% of which was lost to dragout and sewer discharge. Centrifugation and microfiltratiion were evaluated to develop a process that would increase recovery of used ceria, which would then be sent back to the ceria supplier for reclamation and reuse. Full-scale implementation included a high-speed centrifuge that operates continuously with a microfiltration system through recirculation in a single process tank. Sydor Optics has improved ceria recovery from 23% to 48%, saving thousands of dollars annually.

Fabrication Of Composite Membranes For Solar-Thermal Desalination, Andrew Mason, Mahdi Mohammadighaleni, Siamak Nejati

UCARE: Research Products

With rising human populations, the demand for freshwater is an ever-growing problem. One emerging technology to combat this problem is membrane distillation (MD). MD has several advantages for water desalination such as:

•100% rejection of solute (salt, heavy metals, etc.) •Mergeable with other affordable energy sources (solar heat, electric resistance, etc.)

However, at the moment the specific energy consumption (SEC) of MD is very high due to low water production rates and large energy inputs to heat water. In a solar-assisted design for MD, the high cost of solar collectors (~$200/m2) inhibits low cost of water production in comparison to …

Integrity Testing Of Gas Permeable Silicone Filters, Maggie M. Baker, Thomas P. Humann, Kevin J. Yerina

Biomedical Engineering

This report investigates the most reasonable, cost efficient, and reliable ways to integrity test a filter made from a permeable silicone membrane for future biomedical and pharmaceutical applications. The goal of the project was to create a fixture that a pharmaceutical company can use to quickly and reliably test the integrity of the filter. A variety of methods are outlined to test the integrity of the filter, after a series of quantitative tests, a single method was established that meet the requirements most thoroughly. The method that was determined to be most effective involves a series of components including a …

Preparation Of Ceramic Membranes From Sludge Waste, Mai H. Roushdy

Chemical Engineering

Ceramic tiles industry produces industrial waste wit large amount which become a worldwide problem. Ceramic sludge produced from ceramic tiles wastewater treatment plant is routinely discarded as a useless waste. The aim of this paper is to recycle the ceramic sludge waste to be used as raw material for ceramic membrane production. The ceramic sludge was collected, dried, and characterized by mineralogical composition (XRD), thermal analysis (DTA and TGA), and chemical composition determination (XRF). The support ceramic membrane samples were formed, pressed, dried then fired using temperatures from 1050 to 1200 °C for 1 to 3 hours. Verification parameters were …

Towards Efficient Water Treatment: Mechanism Of Colloidal Fouling Of Ultrafiltration Membranes, Ikenna Henry Ozofor

Dissertations, Master's Theses and Master's Reports

This research study first reviewed challenges of conventional and membrane separation systems for water treatment. Though membrane separation systems appeared superior to the conventional counterparts for water and wastewater treatment, wider applications of membrane systems have been limited by some factors, most notably is membrane fouling. Experimental studies were therefore conducted to achieve the goal of this research, which is to investigate how feed properties affect fouling of ultrafiltration (UF) membranes by colloids.

Feed salinity, pH, and nanoparticle concentration were the variables studied to unravel how different UF membranes are fouled by model silica colloids (with average diameter of 25nm). …

Dynamic Study Of Mo/Zsm-5 Catalyst For Ch4 Dehydroadomation, Hadi Yahya Almusawa

Graduate Theses, Dissertations, and Problem Reports (ETD)

Methane dehydroaromatization (CH₄-MDA) is a highly promising venture for natural gas utilization/exploitation, i.e., direct conversion of methane (CH₄) to liquid aromatics (benzene) and hydrogen. This process is a catalytic reaction and therefore, is subject to all the advantages and constraints of catalysis. This study discussed the structure and reactivity of Mo/ZSM-5 zeolite catalysts and their effect on the active conversion of methane to valuable aromatic products such as benzene: 1) The preparation and characterization of Mo/ZSM-5, which are crucial steps in any catalytic reaction process since a better performing catalyst consequently leads to better outcomes; 2) …

A Comparison Of Fiber Mat Thickness Measurement Techniques Using Laser Interferometry And Water Displacement, Ryan Seabeck

Williams Honors College, Honors Research Projects

Polymer fiber mats may often be very thin which leads to complications in measuring thickness. The thickness of fiber mats, however, is crucial in understanding their behavior. Thickness affects how well the mat works as a filter as well as the pressure drop across the mat, and herein lies the need for accurate measurement techniques. Currently two of the available techniques for measuring mat thickness are by laser interferometry[1] and by buoyancy force when submerged in water[2]. Instead of measuring the buoyancy force in this experiment, an enclosure intended to measure the thickness via water displacement was …

Filtration Apparatus Design For Oil-Water Separation Using Membranes And Sponges, Alec Jerger

Williams Honors College, Honors Research Projects

It can be difficult to separate water and oil emulsions through traditional filtration. Therefore, investigations of filtering using thermo-responsive (TR) polymers, in this case poly(vinyl methyl ether) (PVME), was conducted. It’s hypothesized that below its lower critical solution temperature (LCST), PVME has an affinity for water while oil substances do not. Above the LCST the opposite will be true. To verify this hypothesis, iterations of filtration designs were created to provide optimum control over the parameters to measure flow. The final optimized experimental apparatus was a Chromaflex glass column which was air tight and controlled all parameters besides fluid flow. …

Methods For Film Coating Electrospun Fibers, Kristopher Dejean

Williams Honors College, Honors Research Projects

Electrospinning uses high voltages to form polymer nanofiber membranes. These membranes have potential for use in filtration, tissue engineering, drug delivery, and catalysis. The nonwoven fiber mat is malleable but has a low tensile strength compared to a solid film of the same polymer. Joining the fibers with a thin film is desired to balance the strength and flexibility. Three methods of producing a film on fiber membrane were tested. The techniques are spraying then melting, spin coating, and dip coating. Electrospinning setup conditions, solvent ratios, damage to fibers, and spin coating speeds were determined. Research was abruptly stopped and …

Methods For Film Coating Electrospun Fibers, Kristopher Dejean

Williams Honors College, Honors Research Projects

Electrospinning uses high voltages to form polymer nanofiber membranes. These membranes have potential for use in filtration, tissue engineering, drug delivery, and catalysis. The nonwoven fiber mat is malleable but has a low tensile strength compared to a solid film of the same polymer. Joining the fibers with a thin film is desired to balance the strength and flexibility. Three methods of producing a film on fiber membrane were tested. The techniques are spraying then melting, spin coating, and dip coating. Electrospinning setup conditions, solvent ratios, damage to fibers, and spin coating speeds were determined. Research was abruptly stopped and …

Preparation And Characterization Of Ceramic Nanofiltration Membrane Prepared From Hazardous Industrial Waste, Shereen Kamel Amin, Mai Hassan Roushdy, Heba Mohamed Abdallah, Ahmed Mostafa, Magdi Fouad Abadir

Chemical Engineering

Kiln rollers, which are widely used in ceramic tiles production, are usually subjected to surface grinding to remove the contaminations. The resulted fine powder is considered useless waste and a hazardous source of environmental pollution particularly as it contains health‐threatening fine free silica. In the present paper, the grind waste from kiln rollers was reused as raw material in the fabrication of nanofiltration cerramic membrane. The samples of produced ceramic membranes were formed into disks by adding 15% (by weight) organic binder solution with 2% concentration, then pressed at 35 MPa, dried and fired at temperatures range from 1100°C to …

Deposition Of Tio2-Coated Cspbbr3 Perovskite Heterostructure Thin Film, Chutikan Sairot

Chulalongkorn University Theses and Dissertations (Chula ETD)

All-inorganic lead halide perovskite quantum dots have been emerged in recent years for optoelectronic and photovoltaic devices due to their excellent optical properties. In this work, surface coating was carried out by titanium dioxide (TiO2) to coat on the surface of CsPbBr3 PQDs to improve the stability and charge separation property. The FTIR spectra confirmed the formation of TiO2 with an amorphous phase (am-TiO2). The crystallite size of CsPbBr3/am-TiO2 QDs composite was increased to be 13.30 nm from 12.65 nm of CsPbBr3. A slightly decrease of energy bandgap was found compare to CsPbBr3 QDs owing to quantum confinement effect. The …

Bimetallic Nanoparticles Integrated Membranes For Groundwater Remediation: Synthesis, Characterization And Applications, Hongyi Wan

Theses and Dissertations--Chemical and Materials Engineering

The detoxification of chlorinated organics from groundwater, such as trichloroethylene (TCE), tetrachloroethylene (PCE), polychlorinated biphenyl (PCB) and carbon tetrachloride (CTC), is a challenging area. Reductive dechlorination has been investigated using iron and iron-based nanoparticles, such as bare Fe, sulfidized Fe (S-Fe) and palladized Fe (Pd-Fe). However, issues including particle agglomeration, difficulties in recycling and particle leaching have been reported to hinder the application and wide usage of these techniques. The integration of nanoparticles and membranes can address these issues because of the large surface area, stability, and the potential for versatile functionalities. In this study, commercial polyvinylidene difluoride (PVDF) microfiltration …

Nanostructured Metal Thin Films As Components Of Composite Membranes For Separations And Catalysis, Michael J. Detisch

Theses and Dissertations--Chemical and Materials Engineering

Novel metallic thin film composite membranes are synthesized and evaluated in this work for improved separations and catalysis capabilities. Advances in technology that allow for improved membrane performance in solvent separations are desirable for low molecular weight organic separation applications such as those in pharmaceutical industries. Additionally, the introduction of catalytic materials into membrane systems allow for optimization of complex processes in a single step. By adding a nanostructured metallic thin film to its surface, a polymer membrane may be modified to exhibit these improved properties. Using magnetron sputtering, thin metal films may be deposited on commercially available membranes to …

Microfiltration Membrane Pore Functionalization Approaches For Chloro-Organic Remediation To Heavy Metal Sorption, Mohammad Saiful Islam

Theses and Dissertations--Chemical and Materials Engineering

Microfiltration polyvinylidene fluoride (PVDF) membranes have distinct advantage for open structure in terms of high internal surface area and ease of access in the pore domain. Functionalization of PVDF membranes with different functional groups (-COOH, -OH, -SH) enables responsive (pH, temperature) properties to membrane, tuning of effective pore size, controlling permeate flux. PVDF microfiltration membrane functionalization with suitable responsive polymer such as poly acrylic acid (PAA) to incorporate carboxyl (-COOH) group enables further modification of functionalized PAA-PVDF membranes for different application ranging from catalysis, bio reactor to heavy metal sorption platform. As a catalytic reactor bed, this PAA-PVDF membranes are …

The Development Of Temperature And Ph Responsive Hydrogels And Membranes For Selective Sorption Of Perfluoroorganics And Nanoparticle Integrated Catalytic Degradation Of Pcb, Anthony Saad

Theses and Dissertations--Chemical and Materials Engineering

The functionalization and use of responsive and catalytic polymeric membranes and materials were explored for contaminant capture and degradation. While membranes have a wide variety of uses across multiple industries, the inclusion of materials that are temperature and pH responsive in the membrane pore domain yields a wide range of applications and possibilities for water treatment. Temperature and pH responsive polymers, as well as controlled nanostructured materials, were synthesized in membrane pores for advanced adsorption-desorption and catalytic treatment of emerging organic contaminants in water. In this study, supported by the NIEHS, poly-N-isopropylacrylamide (PNIPAm) was used as a model thermo-responsive polymer, …

A Thermodynamic And Feasibility Study Of Green Solvents For The Fabrication Of Water Treatment Membranes, Xiaobo Dong

Theses and Dissertations--Chemical and Materials Engineering

Nonsolvent induced phase separation (NIPS) has been widely used to fabricate polymeric membranes. In NIPS, a polymer is dissolved in a solvent to form a dope solution, which is then cast on a substrate and immersed in a nonsolvent bath, where phase inversion occurs. Petroleum-derived organic solvents, such as N-Methyl-2-Pyrrolidone (NMP) and Dimethylacetamide (DMAc), have been traditionally used to fabricate polymeric membranes via NIPS. However, these solvents may have negative impacts on environmental and human health; therefore, using greener and less toxic solvents, preferably derived from biomass, is of great interest to make membrane fabrication sustainable. In this dissertation, two …

Polymeric Nanocomposite Membranes With Phosphorene Based Pore Fillers For Fouling Control, Joyner Eke

Theses and Dissertations--Chemical and Materials Engineering

Phosphorene is a two-dimensional material exfoliated from bulk phosphorus. Specifically, relevant to the field of membrane science, the band gap of phosphorene provides it with potential photocatalytic properties, which could be explored in making reactive membranes able to control the accumulation of compounds on the surface during filtration, or fouling. Another reason phosphorene is a promising candidate as a membrane material additive is due to its catalytic properties which can potentially destroy foulants on the membrane surface.

The first goal of this study was to develop an innovative and robust membrane able to control and reverse fouling with minimal changes …