Open Access. Powered by Scholars. Published by Universities.®

Catalysis and Reaction Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Physical Sciences and Mathematics

Institution
Keyword
Publication Year
Publication
Publication Type

Articles 721 - 750 of 900

Full-Text Articles in Catalysis and Reaction Engineering

The Preparation And Performance Of The Aqueous Matrix For Molten Carbonate Fuel Cells, Hua-Xin Lin, Mo-Jie Ceng, Bao-Lian Yi May 2005

The Preparation And Performance Of The Aqueous Matrix For Molten Carbonate Fuel Cells, Hua-Xin Lin, Mo-Jie Ceng, Bao-Lian Yi

Journal of Electrochemistry

PVA matrix of MCFC was prepared from the α-LiAlO2 powder, and polyvinylalcohol(PVA), Compared with the conventional PVB matrix, higher porosity, higher thermal weight loss and smaller maximum pore diameter were achieved for PVA matrix. Single cell was assembled with PVA matrix. At reaction gas pressure of 0.9 MPa, under reaction gas utilization of 20%, at 300 and 428.57 mA·cm-2, the cell voltage was 0.849 and 0.739 V respectively, and the output power density was 254.7 and 316.7 mW·cm-2 respectively, which are higher than those of the cell assembled with PVB matrix. During thermal cycles, the cell …

Go to article

Research On Phenol Wastewater Treatment By Electrochemical Oxidation, Tian-Cheng Li, Shen-Lin Zhu Feb 2005

Research On Phenol Wastewater Treatment By Electrochemical Oxidation, Tian-Cheng Li, Shen-Lin Zhu

Journal of Electrochemistry

Electrochemical oxidation is an effective technology for the phenol wastewater treatment, and the anode properties are important to the electrochemical oxidationefficiency. The over-potentials of oxygen evolution have been measured for thestainless steel, feasible graphite and SnO2/Ti anode respectively. Moreover, the synthetic phenol wastewater was treated by the electrochemical oxidation with the stainless steel or feasible graphite anodes. The experimental results showed that the order of the over-potential is SnO2/Ti > graphite > stainless steel; meanwhile, the COD values of purified water were approaching to or less than 100 mg·L-1, and the phenol concentrations in the purified …

Go to article

Influence Of Rare Earth Oxide On The Performance Of Secondary Zinc Electrodes, Xian-Ling Meng, Hua-Bin Yang, Jun-Hong Wang, Zuo-Xiang Zhou Feb 2005

Influence Of Rare Earth Oxide On The Performance Of Secondary Zinc Electrodes, Xian-Ling Meng, Hua-Bin Yang, Jun-Hong Wang, Zuo-Xiang Zhou

Journal of Electrochemistry

Influence of La(OH)3 or Ce(OH)3 in secondary zinc electrode was investigated by the cyclic voltammetry, potentiodynamic polarizationand potentiostatic polarization tests and influence of La2O3 or CeO2 in the charge/discharge performance of Zn/Ni battery was studied by galvanostatic charge/discharge experiment. The results showed that the film of rare earth hydroxide prevented the zincate species from transferring toward solution, enhanced hydrogen overpotential and decreased thecorrosion current density (icorr), and therefore inhibited zinc corrosion. The potentiostatic polarization results at100mV overpotential showed that La(OH)3 or Ce(OH)3 oated on the zinc electrode effectively suppressed the …

Go to article

Comparative Study Of The Dynamics Of Circulating Fluidized Bed Riser And Downer Of Equal Diameters, Samwel V. Manyele Dec 2004

Comparative Study Of The Dynamics Of Circulating Fluidized Bed Riser And Downer Of Equal Diameters, Samwel V. Manyele

Tanzania Journal of Engineering and Technology (TJET)

The microscopic flow dynamics of the 100-mm internal diameter riser/downer circulating fluidized bed (CFB) unit were monitored using a solids concentration fiber optic probe. The comparison was conducted by comparing radial profiles Of the dynamic parameters derived from time-series analysis techniques (statistical and chaos analyses). The solids concentration signals used were recorded under similar operating conditions (gas velocity of 8.0 m/s and solids flux of 100 kg/m2s). Similar axial elevations were compared (entrance and fully developed sections of die reactors). A1 each loca!ion, the signals were sampled a! afrequency of 970 Hz for duration of 30 seconds. It was observed …

Go to article

Electrochemical Behaviours Of Hemoglobin-Ddab-Modified Powder Microelectrode And The Application Of The Powder Microelectrode In Determination Of Nitric Oxide, Zhi-Mou Guo, Huan Liu, Jian Chen, Wen-Ting Zhang Nov 2004

Electrochemical Behaviours Of Hemoglobin-Ddab-Modified Powder Microelectrode And The Application Of The Powder Microelectrode In Determination Of Nitric Oxide, Zhi-Mou Guo, Huan Liu, Jian Chen, Wen-Ting Zhang

Journal of Electrochemistry

The electrochemical behaviours of DDAB-Hb-PME were studied in this paper. The (apparent) surface concentration of Hb was enhanced greatly by using the powder microelectrode (technique). NO reacts with Hb and absorbs on the surface of the modified carbon powder. Therefore, the output of the electrode was enhanced greatly by employing PME with higher reaction surface (area). The sensitivity of DDAB-Hb-PME is 3.1 mA/μmol·L-1·cm2, which is much larger than the values obtained with the traditional electrodes. The detection limit is 9 nmol·L-1 and the linear response range is 9～100 nmol·L-1.

Go to article

Electrocatalytic Performances Of Carbon Nanotube Air Electrode For Oxygen Reduction, Feng-Ming Zhao, Chun-An Ma Nov 2004

Electrocatalytic Performances Of Carbon Nanotube Air Electrode For Oxygen Reduction, Feng-Ming Zhao, Chun-An Ma

Journal of Electrochemistry

The air electrodes with different mass ratio of Pt/active carbon or carbon nanotube as catalyst layer material have been prepared. The electrocatalytic performances for oxygen reduction were evaluated by means of polarization curve and electrochemical impedance spectroscopy (EIS). The results disclosed that carbon nanotubes dealt with nitric acid in the catalyst layer had been improved obviously on the electrocatalytic activity. After the surface of carbon nanotube was oxygenated and aggraded with platinum, the catalyst had obviously effects on the electrocatalytic activity. The air electrode with the mass ratio of active carbon to Pt/carbon nanotube in 4∶1 showed better electrocatalytic activity, …

Go to article

Effect Of Fe3+ Dopen Of Titanium Dioxide Film On Absorption Spectra And Photo Catalysis, Mei-Qun Xiao, Jia-Nian Shen, Moucheng Li, Peng-Fei Wu, Dong Liu, Yu-Juan Zhang Nov 2004

Effect Of Fe3+ Dopen Of Titanium Dioxide Film On Absorption Spectra And Photo Catalysis, Mei-Qun Xiao, Jia-Nian Shen, Moucheng Li, Peng-Fei Wu, Dong Liu, Yu-Juan Zhang

Journal of Electrochemistry

Photo-catalytic titanium dioxide film in nano crystalline has been prepared by electrochemical oxidation process and adding different amount of ferric ion into the electrolyte during the anodic oxidation.The effects of Fe3+ dopen on absorption spectra and photo-catalytic of the titanium dioxide films have been studied. It shows that the Fe3+ dopen caused the red shife of the absorption edge for the incoming light and exhibited the improved photocatalytic reactivity.

Go to article

Anodic Dissolution Of Aluminum In Koh-Ethanol Solutions, Hai-Bo Shao, Jian-Ming Wang, Xiao-Yan Wang, Yi Zheng, Jian-Qing Zhang Nov 2004

Anodic Dissolution Of Aluminum In Koh-Ethanol Solutions, Hai-Bo Shao, Jian-Ming Wang, Xiao-Yan Wang, Yi Zheng, Jian-Qing Zhang

Journal of Electrochemistry

The feasibility of employing aluminum in KOH ethanol solution as a battery anode system was discussed. Weight loss measurement showed that the corrosion rate of Al is low enough to be used in sealed batteries. Through the measurements done by anodic polarization, EIS and galvanostatic discharge, it was found that Al is electrochemical active in a wide potential range in this system, and its discharge mechanism is similar to that of Al in aqueous solution. The discharge potential increased rapidly after a period of time, which might be caused by the discharge products depositing on the electrode surface.

Go to article

Preparation And Photo-Catalyst Properties Of The α-Fe2O3-Tio2 Films On Sodium Alginate Polymer, Li-Qin Chen, Huai-Zhen Zhong, Ri-Yao Chen, Xi Zheng, Zhen Chen Nov 2004

Preparation And Photo-Catalyst Properties Of The α-Fe2O3-Tio2 Films On Sodium Alginate Polymer, Li-Qin Chen, Huai-Zhen Zhong, Ri-Yao Chen, Xi Zheng, Zhen Chen

Journal of Electrochemistry

Three new nano thin films of α-Fe2O3, TiO2 and α-Fe2O3-TiO2 by doping their powder with sodium alginate polymer were prepared. Surface structure and catalytic activities of the films were characterized by FTIR, XRD, PL, TEM and I-V techniques. The results of UV-visible absorption showed that the methylene blue was mineralized in aqueous of α-Fe2O3/SA, TiO2/SA and (α-(Fe2O3))-TiO2 /SA upon radiation with ultra violet light. α-Fe2O3 enhanced their photo-decolorized-activities by doping 15% TiO2.

Go to article

Electrochemical Reduction Of Nitrobenzene On The Wc Electrode In Acidic Solution, Chun-An Ma, You-Qun Chu, Ying-Hong Zhu, Zhi-Hua Xu Aug 2004

Electrochemical Reduction Of Nitrobenzene On The Wc Electrode In Acidic Solution, Chun-An Ma, You-Qun Chu, Ying-Hong Zhu, Zhi-Hua Xu

Journal of Electrochemistry

The tungsten carbide (WC) electrode was constructed by using polyterafluoroethylene as binder. The electrochemical behavior of nitrobenzene on the WC electrode in acidic solution was investigated by cyclic voltammetry, linear scan method and chronoamperometry. Experimental results showed that WC electrode had good activity for the electrochemical reduction of nitrobenzene, and the electrode process was controlled by diffusion and electrochemical stepssimultaneously. The apparent active energy of the electrode process is 23.7kJ⋅mol-1, while the active energy of the electrochemicalstep is 10.91kJ⋅mol-1.

Go to article

Synthesis Of (S)-3-Phenylpropane-2-Tert-Butoxycarbonylamino-1-Thiol And Its Electrochemical Behavior Self-Assembled On Gold, Ru Sun, Jian-Feng Ge, Mei Wang, Ren-Ao Gu Aug 2004

Synthesis Of (S)-3-Phenylpropane-2-Tert-Butoxycarbonylamino-1-Thiol And Its Electrochemical Behavior Self-Assembled On Gold, Ru Sun, Jian-Feng Ge, Mei Wang, Ren-Ao Gu

Journal of Electrochemistry

The synthesis of (S)-3-Phenylpropane-2-tert-butoxycarbonylamino-1-thiol(N-Boc-APT) from L-phenylalanine was reported. L-Phenylalanine was reduced to the corresponding amino alcohol, protection of the amino group using tert-butyl pyrocarbonate gave (S)-2-tert-butoxycarbonylamino-3-phenylpropane-1-ol, which was then O-mesylated and treated with potassium thioacetate in DMF to give 3-phenylpropane-2-tert- butoxycarbonylamino-1-etylmercapto. After the acetyl group was removed with ammonia in alcohol, the desired target molecular was obtained. The structure of intermediate and target molecular was conformed by IR and 1HNMR. We made N-Boc-APT self-assemble-modificated gold electrode and investigated its electrochemical behavior. The CV results of methylene blue on nano-Au/N-Boc-APT SAM/Au electrode showed that nano-Au could speed this electron transfer …

Go to article

Solid State Synthesis And Electrocatalysis Of Pt/Moo3 For The Oxidation Of Methanol, Qing Wang, Yi-Ming Zhou, Yang Shao, Yi-Gang Ji, Juan Xu, Ya-Wen Tang, Tian-Hong Lu, Tao Shen Aug 2004

Solid State Synthesis And Electrocatalysis Of Pt/Moo3 For The Oxidation Of Methanol, Qing Wang, Yi-Ming Zhou, Yang Shao, Yi-Gang Ji, Juan Xu, Ya-Wen Tang, Tian-Hong Lu, Tao Shen

Journal of Electrochemistry

The electrocatalyst, Pt/MoO3 synthesized by solid state reaction, was used for the oxidation of methanol in direct methanol fuel cells. The X-Ray diffraction and cyclic voltammetry were employed to investigate the performance of the material. It was shown that the typical diffraction peaks for Pt appeared in XRD. And a good electrocatalysis for methanol oxidation was observed. The peak potential of the methanol oxidation appeared at ca. 0.63V(vs.SCE) and the peak current density for the oxidation was 78.1 mA⋅cm-2.

Go to article

Synthesis And Electrochemical Behavior Of Layered-Structure Limn1-XCrXO2, Jie Xiao, Hui Zhan, Yun-Hong Zhou Aug 2004

Synthesis And Electrochemical Behavior Of Layered-Structure Limn1-XCrXO2, Jie Xiao, Hui Zhan, Yun-Hong Zhou

Journal of Electrochemistry

The Layered-structure LiMn1-xCrxO2(x=0, 0.15) solid solution has been prepared by the rheological phase method. From the XRD results, undoped LiMnO2 crystallized almost entirely in the orthorhombic phase while the structure of LiMn0.85Cr0.15O2 belongs to monoclinic phase. TEM investigation shows that the final powder product consists of ultrafine spherical particles which are distributed homogeneously, with the average diameter ranging from 60 to 300nm. The initial discharge capacity of LiMn0.85Cr0.15O is much higher than that of undoped LiMnO2. After 40 cycles, the capacity retention …

Go to article

Lithium Insertion Into Tio2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin Aug 2004

Lithium Insertion Into Tio2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin

Journal of Electrochemistry

TiO2(B) Nanobelts were synthesized by using the "Soft chemical"method. The products were characterized by means of transmission electron microscope(TEM), X-ray diffraction(XRD), Raman spectrum and energy dispersive spectrum(EDS). Galvanostatic charging and discharging tests showed that lithium-ion intercalation/deintercalation occurred reversibly in the TiO2(B) nanobelts electrode, and a high capacity (265 mAh·g-1) can be obtained. The results suggested that TiO2(B) Nanobelts might be a promising negative electrode material of second Lithium battery.

Go to article

Preliminary Study Of Speek Membranes For Direct Methanol Fuel Cells Application, Su-Zhen Ren, Zhen-Xing Liang, Xin-Sheng Zhao, Qin Xing, Gong-Quan Sun, Xue-Feng Yang Aug 2004

Preliminary Study Of Speek Membranes For Direct Methanol Fuel Cells Application, Su-Zhen Ren, Zhen-Xing Liang, Xin-Sheng Zhao, Qin Xing, Gong-Quan Sun, Xue-Feng Yang

Journal of Electrochemistry

This paper describes the methanol permeability characterization of SPEEK membranes and their feasibility for DMFC application. The SPEEK membranes showed a significant lower methanol permeation than Nafion 115 determined from voltammetric methods. An increase in open circuit voltage was found in the performance of SPEEK membranes in DMFC. The power density of the cell using SPEEK membrane was considerably poorer than that of Nafion 115. If modified properly, the SPEEK membranes can be chosen for DMFC application based on this study.

Go to article

Fabrication Of Solid Oxide Fuel Cells And Analysis Of Their Structure And Performance, Nai-Tao Yang, Bo Meng, Ru-Jun Yu, Xiao-Yao Tan Aug 2004

Fabrication Of Solid Oxide Fuel Cells And Analysis Of Their Structure And Performance, Nai-Tao Yang, Bo Meng, Ru-Jun Yu, Xiao-Yao Tan

Journal of Electrochemistry

An intermediate temperature solid oxide fuel cell (IT-SOFC) was fabricated by co-copressing-sintering methods, and the electrolyte of Ce0.8Gd0.2O1.9 (CGO) and cathode materials of La0.6Sr0.4Co0.2Fe0.8O3-α (LSCF) were prepared by sol-gel method. The effect of preparation methods on the microstructure of the prepared fuel cells was analyzed by SEM . It shows that the cells prepared by the co-pressing/co-sintering method possess a dense electrolyte layer and a compact interface between electrolyte and anode but a curved configuration, while those prepared by the colloidal technique have a flat configuration …

Go to article

Study On An Intermediate Temperature Planar Solid Oxide Fuel Cell, Shao-Rong Wang, Wen-Xia Chen, Ting-Lian Wen, Jia-Di Cao, Zhi-Yi Lv, Da-Qian Wang Aug 2004

Study On An Intermediate Temperature Planar Solid Oxide Fuel Cell, Shao-Rong Wang, Wen-Xia Chen, Ting-Lian Wen, Jia-Di Cao, Zhi-Yi Lv, Da-Qian Wang

Journal of Electrochemistry

Tape cast method was applied to prepare green sheets of Ni/YSZ anode supported YSZ thin film. After isostatic pressure treatment and cosintering, the YSZ film on the Ni/YSZ anode was gas-tight dense, and 15~30 μm thick. The area of the composite film was over 100 cm2. A Ce0.8Sm0.2O1.9 (CSO) interlayer was sintered on to the YSZ electrolyte film to protect La0.6Sr0.4CoO3 (LSCO) cathode from reaction with YSZ at high temperatures. The LSCO cathode layer was screen printed onto the CSO interlayer and sintered at 1200 ℃ for 3 …

Go to article

Review Of The Product Development Process And Information Flow In The Manufacturing Industry: Problems And A Possible Wav Forward, E Opiyo Jun 2004

Review Of The Product Development Process And Information Flow In The Manufacturing Industry: Problems And A Possible Wav Forward, E Opiyo

Tanzania Journal of Engineering and Technology (TJET)

No abstract provided.

Go to article

Mathematical Simulation Of The Influence Of Volatile Ma•Rrer Cloud On Heterogeneous Ignition Of Single Coal Particles, Hassan Ratal Ambula Jun 2004

Mathematical Simulation Of The Influence Of Volatile Ma•Rrer Cloud On Heterogeneous Ignition Of Single Coal Particles, Hassan Ratal Ambula

Tanzania Journal of Engineering and Technology (TJET)

Asimple model has been developed to predict the heterogeneous ignition temperature for single coal particles under conditions of negligible, natural and forced convections. These conditions cause different sizes Of volatile matter cloud that surround the coal particle. The model is based on the ignition Of a single coal particle heated by irradiation from spot heaters in a cold (ambient) surrounding. Energy from the particle surface oxidation, volatile matter combustion and physical heating from the spot heaters are all included in rhe particle energv balance. General ignüion criterion is used to determine the ignition point. The agreement between the experimental and …

Go to article

Investigation Of Adsorption And Oxidation Behavior Of Isosafrole On A Smooth Pt, Xiao-Hong Zhang, Xiao-Jing Su, Qi-Ling Zhong, Lei Zhang, De-Sheng Mei, Bin Ren, Zhong-Qun Tian May 2004

Investigation Of Adsorption And Oxidation Behavior Of Isosafrole On A Smooth Pt, Xiao-Hong Zhang, Xiao-Jing Su, Qi-Ling Zhong, Lei Zhang, De-Sheng Mei, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

The electro-oxidation of isosafrole on a smooth platinum electrode was investigated in the non-aqueous solution. The CV curve shows two oxidation peaks and one reduction peak in the potential region between -0.5 V and 1.95 V. The relation between the oxidation and reduction peaks has been determined also by CV. The adsorption behavior of isosafrole on Pt was also investigated.

Go to article

Electrocatalytic And Lifetime Studies Of Commercial Catalystsin A Pemfc, Cheng Xuan, Yan-Yun Ma, Li Qi, Cheng Peng, Ling Chen, Jun Zhao, Ying Zhang, Qin-Bai Fan May 2004

Electrocatalytic And Lifetime Studies Of Commercial Catalystsin A Pemfc, Cheng Xuan, Yan-Yun Ma, Li Qi, Cheng Peng, Ling Chen, Jun Zhao, Ying Zhang, Qin-Bai Fan

Journal of Electrochemistry

A particularly designed H-type cell was used to simulate the operating condition of a hydrogen-air proton exchange membrane fuel cell (PEMFC). The electrocatalytic activity, morphology, structure and lifetime of commercially available catalysts, carbon support platinum (Pt/C) and unsupported platinum-ruthenium (Pt-Ru), were preliminary studied by carrying out electrochemical measurements and by SEM, XRD techniques. The catalysts were simultaneously tested in the H-cell under operation, and also separately tested in a conventional electrochemical cell for comparison. It was found that the characteristic peaks of hydrogen adsorption/desorption on cyclic voltammograms shifted considerably to a more positive direction for Pt/C, while a more negative …

Go to article

Study On Reduction Process Of Electrolyic Manganese Dioxide In Situ By Ultraviolet-Visible Absorption Spectroscopy, Li-Cai Zhu, Zhong-Zhi Yuan, Wei-Shan Li May 2004

Study On Reduction Process Of Electrolyic Manganese Dioxide In Situ By Ultraviolet-Visible Absorption Spectroscopy, Li-Cai Zhu, Zhong-Zhi Yuan, Wei-Shan Li

Journal of Electrochemistry

The concentrationsof soluble Mn(Ⅲ) species, during the reduction ofelectrolytic MnO2 (EMD) in alkaline solution,have been monitored in situ by UV-visible spectroscopy. The concentration of Mn(Ⅲ) ion in solution changes with discharge time. The first electron discharge process of EMD can be described by three different steps: 1) the reduction of Mn4+ ions on the surface of EMD particles and the structural defect regions within the EMD, 2) the reduction of Mn4+ ions in ramsdellite, 3)the reduction of Mn4+ ions in pyrolusite. During the second electron discharge of EMD, the soluble Mn(Ⅲ) is reduced to Mn(Ⅱ) , …

Go to article

Progress In Research For Biofuel Cell, Yue Bao, Xia-Qin Wu Feb 2004

Progress In Research For Biofuel Cell, Yue Bao, Xia-Qin Wu

Journal of Electrochemistry

In this article, research progresses of the biofuel cell in recent years were summarized. The operation principle and classification of the biofuel cells were described. The role of the mediator for promoting electron transfer in biofuel cells and the techniques for improving the electric properties of biofuel cells, such as output potential, were discussed with some attracting research instances. Finally, the choke points for research of biofuel cell were explored, and the application prospect of biofuel cells was forecasted.

Go to article

Preparation, Structure And Electrochemical Hydrogenation Of Carbon Nanotubes Supported Platinum Catalysts, Qing-Gang He, Xiao-Zi Yuan, Xian-Xia Yuan, Zi-Feng Ma Feb 2004

Preparation, Structure And Electrochemical Hydrogenation Of Carbon Nanotubes Supported Platinum Catalysts, Qing-Gang He, Xiao-Zi Yuan, Xian-Xia Yuan, Zi-Feng Ma

Journal of Electrochemistry

In this paper, Pt/CNTs catalyst was prepared and its electrocatalytic property was studied by obtaining cycling voltammetry curves (C-V) and Tafel curves. In addition, the XRD,XPS and TEM tests were carried out to determine the structure and composition of the catalysts. It can be found that the platinum loading has been increased significantly using a carbon nanotubes support. Dispersion of Platinum was better and gave more active sites. The electrochemical characteristic of Pt/CNTs was also more desirable than that of Pt/C catalys t(Johnson Matthey). In conclusion, carbon nanotubes can played a conspicuous role in "electrogenerative" processes of PEMFC hydrogenation reactor.

Go to article

Template Synthesis Of Highly Ordered Monocrystalline Metal Nanowire Arrays By A Two-Step Ac Electrodeposition, Juan Xiang, Jing-Hua Tian, Zi-Mian Ni, Zhi-Feng Huang, Bo Liu, Zhong-Qun Tian Feb 2004

Template Synthesis Of Highly Ordered Monocrystalline Metal Nanowire Arrays By A Two-Step Ac Electrodeposition, Juan Xiang, Jing-Hua Tian, Zi-Mian Ni, Zhi-Feng Huang, Bo Liu, Zhong-Qun Tian

Journal of Electrochemistry

The monocrystalline metal nanowire arrays were prepared by using a two-step AC electrodeposition in porous anodic aluminum oxide (AAO) template. The growth mechanism of nanowires was discussed. As a result, it has been found that the second voltage pulse has a considerable effect on the pore-filling ratio, the uniformity and the crystal structure, whereas the initial voltage pulse affects only the pore-filling ratio. Using the two-step AC electrodeposition, a highly ordered monocrystalline metal nanowire arrays with a pore-filling ration above 95% can be easily obtained.

Go to article

Electrochemical Synthesis Of Ferrate(Vi) By Anodic Oxidation, Jia-Ju Xu, Jian-Ming Wang, Wei-Hua Yang, Cheng Chen, Jian-Qing Zhang Feb 2004

Electrochemical Synthesis Of Ferrate(Vi) By Anodic Oxidation, Jia-Ju Xu, Jian-Ming Wang, Wei-Hua Yang, Cheng Chen, Jian-Qing Zhang

Journal of Electrochemistry

The ferrate(Ⅵ) was synthesized by electrochemical anodic oxidation. The effects of preparation conditions on the current yield of ferrate(VI) synthesis have been studied in this work. The experimental results showed that grey cast iron as an anodic material is suitable for electrochemical synthesis and NaOH solution as an electrolyte results in a higher current yield than KOH solution. The highest current yield was obtained at a current density (4.54) mA·cm-2, temperature 20 ℃ and 14 mol·dm-3 NaOH. In this case, a current yield of 68.5% was obtained by electrolysis for 1 h.

Go to article

Studies On The Mechanism Of Electroreduction Of Oxalic Acid, Yu-Zhan Li, Xin Liu, Rui-Sheng Hu, Deng-Ping Gu Feb 2004

Studies On The Mechanism Of Electroreduction Of Oxalic Acid, Yu-Zhan Li, Xin Liu, Rui-Sheng Hu, Deng-Ping Gu

Journal of Electrochemistry

The electroreduction mechanism of oxalic acid on Pb electrode in Na2SO4 solution were investigated using high scan rate cyclic voltammetry and chronoamperometry. The dynamic parameters for the first step electron transter reaction of oxalic acid electroreduction by were determined. The corresponding reduction peak potentials of oxalic acid, glyoxylic acid and glycolic acid in the cyclic voltammogranis obtained in the same condition were compared, and the intermediate reduction products of oxalic acid were suggested. The results showed that oxalic acid is weakly absorbed on the lead electrode.

Go to article

Preparation And Characterization Of Y-Type Carbon Nanotubes By Using Anodized Alumina Oxide (Aao) Template, Jing Zhang, Quan-Yong Gao, Yong Yang Nov 2003

Preparation And Characterization Of Y-Type Carbon Nanotubes By Using Anodized Alumina Oxide (Aao) Template, Jing Zhang, Quan-Yong Gao, Yong Yang

Journal of Electrochemistry

In this work, potential-modulation method was used in two-step anodization process to make an AAO template with Y-type nanochannels. Then Y-type carbon nanotubes with controlled length and branch angle were prepared in the template based on chemical vapor decomposion (CVD) method with Co particles as catalyst and C2H2 as carbon source. The Y-type nanotube branches exhibit the angle distribution ranging from 20° to 120°. The results demonstrated that the oxidation potential should be responsible for the angles and length of the branches. Short pulse and high oxidation potential will result in the short and dense nanotube branches.

Go to article

Application Of Hydrogen-Storage Alloy Electrode In Electrochemical Reduction Of Glucose, Hui Chen, You-Gen Tang, Zheng Tang Nov 2003

Application Of Hydrogen-Storage Alloy Electrode In Electrochemical Reduction Of Glucose, Hui Chen, You-Gen Tang, Zheng Tang

Journal of Electrochemistry

Electrolysis of glucose was performed at constant potential using hydrogen-storage alloy as catalytic reduction electrode. It was found that the superficial treatment and activation of hydrogen-storage alloy powder had obvious effects on improving the current efficiency of sorbitol. Under the optimums, current efficiency of sorbitol by electrolyzing glucose was over 94%. The yield of sorbitol was over 80%, the lifespan of electrode was tested and analyzed, the ways of regeneration were discussed.

Go to article

Study On Degradation Of Phenol By Electrochemical Oxidation, Yue-Li Liu, Hong-Hua Ge Nov 2003

Study On Degradation Of Phenol By Electrochemical Oxidation, Yue-Li Liu, Hong-Hua Ge

Journal of Electrochemistry

Electrochemical oxidation of phenol was carried out by the Dimensionally Stable Anodes (DSA) electrode, which has been discarded as waste by alkali chloride factory. The result indicates that a good phenol removal can be obtained under certain phenol concentration by the DSA electrode. The key factor in effecting phenol removal of electrochemical oxidation is applied current density, the following factors are pH, electrolyte concentration and phenol concentration. After experiments, the optimal test conditions are 30 mA/cm2, pH 10, electrolyte concentration 10 mg/L, phenol concentration 10 mg/L.67% CODcr removal and 90% absorbance removal are gained by electrochemical oxidation for …

Go to article

First Prev Next Last