Open Access. Powered by Scholars. Published by Universities.®

Chemical Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Chemical Engineering

Discipline
Institution
Publication Year
Publication
Publication Type

Articles 91 - 120 of 248

Full-Text Articles in Chemical Engineering

A Mathematical Model Of Oxide/Carbon Composite Electrode For Supercapacitors, Hansung Kim, Branko N. Popov Jan 2003

A Mathematical Model Of Oxide/Carbon Composite Electrode For Supercapacitors, Hansung Kim, Branko N. Popov

Faculty Publications

A pseudo two-dimensional model is developed for the general application of supercapacitors consisting of an oxide/carbon composite electrode. The model takes into account the diffusion of protons in the oxide particle by employing the method of superposition. RuO2/carbon system is modeled as a specific example. From the simulation data, it is found that the oxide particle size and proton diffusion coefficient have an enormous effect on the performance at high discharge rate due to the limitation of proton transport into RuO2 particles. With increasing carbon ratio, the porosity of electrode increases, which causes the potential drop in …

Go to article

A Novel Electrodeposition Process For Plating Zn-Ni-Cd Alloys, Hansung Kim, Branko N. Popov, Ken S. Chen Jan 2003

A Novel Electrodeposition Process For Plating Zn-Ni-Cd Alloys, Hansung Kim, Branko N. Popov, Ken S. Chen

Faculty Publications

Zn-Ni-Cd alloy was electrodeposited from an alkaline electrolytic bath under potentiostatic conditions. Bath analyses using a pH concentration diagram reveal that addition of a complexing agent is essential to maintain the bath stability. Introduction of a low concentration of CdSO4 reduces the anomalous nature of the Zn-Ni deposit. Deposits obtained from the electrolytic bath which contains 60 g/L of ZnSO4·7H2O, 40 g/L of NiSO4·6H2O, 1 g/L of CdSO4, and 80 g/L of (NH4)2SO4 in the presence of additives and ammonium hydroxide at pH 9.3 …

Go to article

Water Transport In Polymer Electrolyte Membrane Electrolyzers Used To Recycle Anhydrous Hcl: I. Characterization Of Diffusion And Electro-Osmotic Drag, Sathya Motupally, Aaron J. Becker, John W. Weidner Jan 2002

Water Transport In Polymer Electrolyte Membrane Electrolyzers Used To Recycle Anhydrous Hcl: I. Characterization Of Diffusion And Electro-Osmotic Drag, Sathya Motupally, Aaron J. Becker, John W. Weidner

Faculty Publications

In this paper, diffusion and electro-osmotic drag of water across Nafion® membranes in the presence of HCl are characterized. For all the measurements, one side of the Nafion membrane was in contact with liquid water and the other side with gaseous anhydrous HCl. To characterize diffusion of water, the open-circuit flux of water across a catalyst-coated Nafion 115 membrane was measured as a function of HCl flow rate and temperature at a constant cell pressure of 1 atm. Due to the nature of varying driving force for diffusion as a function of HCl flow rate, the experimental data was analyzed …

Go to article

Development Of A Novel Co Tolerant Proton Exchange Membrane Fuel Cell Anode, Andrew T. Haug, Ralph E. White, John W. Weidner, Wayne Huang Jan 2002

Development Of A Novel Co Tolerant Proton Exchange Membrane Fuel Cell Anode, Andrew T. Haug, Ralph E. White, John W. Weidner, Wayne Huang

Faculty Publications

Typically Pt is alloyed with metals such as Ru, Sn, or Mo to provide a more CO-tolerant, high-performance proton exchange membrane fuel cell (PEMFC) anode. In this work, a layer of carbon-supported Ru is placed between the Pt catalyst and the anode flow field to form a filter. When oxygen is added to the fuel stream, it was predicted that the slow H2 kinetics of Ru in this filter would become an advantage compared to Pt and Pt:Ru alloy anodes, allowing a greater percentage of O2 to oxidize adsorbed CO to CO2. With an anode feed …

Go to article

Studies On Capacity Fade Of Spinel-Based Li-Ion Batteries, Ramadass Premanand, Anand Durairajan, Bala Haran, Ralph E. White, Branko N. Popov Jan 2002

Studies On Capacity Fade Of Spinel-Based Li-Ion Batteries, Ramadass Premanand, Anand Durairajan, Bala Haran, Ralph E. White, Branko N. Popov

Faculty Publications

The performance of Cell-Batt® Li-ion cells using nonstoichiometric spinel as the positive electrode material has been studied at different charging rates. The capacity of the cell was optimized based on varying the charging current and the end potential. Subsequent to this, the capacity fade of these batteries was studied at different charge currents. During cycling, cells were opened at intermittent cycles and extensive material and electrochemical characterization was done on the active material at both electrodes. For all charge currents, the resistance of both the electrodes does not vary significantly with cycling. This result is in contrast with cells …

Go to article

Modeling The Effects Of Ion Association On Alternating Current Impedance Of Solid Polymer Electrolytes, Changqing Lin, Ralph E. White, Harry J. Ploehn Jan 2002

Modeling The Effects Of Ion Association On Alternating Current Impedance Of Solid Polymer Electrolytes, Changqing Lin, Ralph E. White, Harry J. Ploehn

Faculty Publications

This work presents a rigorous continuum model describing the transport of ions and associated ion pairs in solid polymer electrolytes subjected to small amplitude alternating current (ac) excitation. The model treats ion association as a reversible reaction among ions and ion pairs. Dimensionless governing equations are developed from component mass balances, flux equations based on dilute solution theory, and the Poisson equation. Assuming reversible electrode reactions and electroneutrality, the model equations have an analytical solution. Further simplifications are possible in limiting cases (weak and strong association, zero and infinite frequency excitation), giving expressions consistent with previously published models. We use …

Go to article

Estimation Of Diffusion Coefficient Of Lithium In Carbon Using Ac Impedance Technique, Qingzhi Guo, Venkat R. Subramanian, John W. Weidner, Ralph E. White Jan 2002

Estimation Of Diffusion Coefficient Of Lithium In Carbon Using Ac Impedance Technique, Qingzhi Guo, Venkat R. Subramanian, John W. Weidner, Ralph E. White

Faculty Publications

The validity of estimating the solid phase diffusion coefficient, Ds, of a lithium intercalation electrode from impedance measurement by a modified electrochemical impedance spectroscopy (EIS) method is studied. A macroscopic porous electrode model and concentrated electrolyte theory are used to simulate the synthetic impedance data. The modified EIS method is applied for estimating Ds. The influence of parameters such as the exchange current density, radius of active material particle, solid phase conductivity, porosity, volume fraction of inert material, and thickness of the porous carbon intercalation electrode, the solution phase diffusion coefficient, and transference number, on the …

Go to article

Using Sputter Deposition To Increase Co Tolerance In A Proton-Exchange Membrane Fuel Cell, Andrew T. Haug, Ralph E. White, John W. Weidner, Wayne Huang, Steven Shi, Narender Rana, Stephan Grunow, Timothy C. Stoner, Alain E. Kaloyeros Jan 2002

Using Sputter Deposition To Increase Co Tolerance In A Proton-Exchange Membrane Fuel Cell, Andrew T. Haug, Ralph E. White, John W. Weidner, Wayne Huang, Steven Shi, Narender Rana, Stephan Grunow, Timothy C. Stoner, Alain E. Kaloyeros

Faculty Publications

Placing a layer of Ru atop a Pt anode increases the carbon monoxide tolerance of proton-exchange membrane fuel cells when oxygen is added to the fuel stream. Sputter-deposited Ru filter anodes composed of a single Ru layer and three Ru layers separated by Nafion-carbon ink, respectively, were compared to Pt, Pt:Ru alloy, and an ink-based Ru filter anodes. The amount of Pt in each anode was 0.15 mg/cm2 and the amount of Ru in each Ru-containing anode was 0.080 mg/cm2. For an anode feed consisting of hydrogen, 200 ppm CO, and 2% O2 (in the form …

Go to article

Increasing Proton Exchange Membrane Fuel Cell Catalyst Effectiveness Through Sputter Deposition, Andrew T. Haug, Ralph E. White, John W. Weidner, Wayne Huang, Steven Shi, Timothy Stoner, Narender Rana Jan 2002

Increasing Proton Exchange Membrane Fuel Cell Catalyst Effectiveness Through Sputter Deposition, Andrew T. Haug, Ralph E. White, John W. Weidner, Wayne Huang, Steven Shi, Timothy Stoner, Narender Rana

Faculty Publications

Sputter deposition has been investigated as a tool for manufacturing proton-exchange membrane fuel cell (PEMFC) electrodes with improved performance and catalyst utilization vs. ink-based electrodes. Sputter-depositing a single layer of Pt on the gas diffusion layer provided better performance (0.28 A/cm2 at 0.6 V) than sputtering the Pt directly onto a Nafion membrane (0.065 A/cm2 at 0.6 V) and equaled the performance of the baseline for an equivalent Pt loading. Sputter-depositing alternating layers of Pt and Nafion-carbon ink (NCI) onto the membrane did not increase the performance over the baseline as measured in amperes per centimeter squared due …

Go to article

Electrochemical Filtering Of Co From Fuel-Cell Reformate, Balasubramanian Lakshmanan, Wayne Huang, John W. Weidner Jan 2002

Electrochemical Filtering Of Co From Fuel-Cell Reformate, Balasubramanian Lakshmanan, Wayne Huang, John W. Weidner

Faculty Publications

A proton exchange membrane fuel cell was used as a flow reactor for continuous preferential oxidation of CO over H2 from 1.0% CO in H2 under pulse-potential control. By varying the pulse profile ~e.g., on-time, off-time, pulse potential! the CO and H2 oxidation currents were varied independently. The improvement in faradaic selectivity between CO and H2 oxidation results from the promotion of CO adsorption during the off ~i.e., open-circuit! portion of the pulse. Therefore, during the on portion CO oxidation was preferred while the surface was covered with CO.

Go to article

Anodic Behavior Of Ti In Koh Solutions: Ellipsometric And Micro-Raman Spectroscopy Studies, A. Prusi, Lj. Arsov, Bala Haran, Branko N. Popov Jan 2002

Anodic Behavior Of Ti In Koh Solutions: Ellipsometric And Micro-Raman Spectroscopy Studies, A. Prusi, Lj. Arsov, Bala Haran, Branko N. Popov

Faculty Publications

Anodic formation of oxide films on titanium surfaces, in various concentrations of aqueous KOH solutions, have been studied using ellipsometry and micro-Raman spectroscopy. By in situ ellipsometric measurements the coefficient of film thickness growth and indexes of refraction of anodic oxide films have been determined. The voltage at which the oxide film breaks down is strongly dependent on the KOH concentration. Further, the solution concentration strongly influences the potential at which the oxide film is transformed from the amorphous state to crystalline form. Using micro-Raman spectroscopy four crystalline forms of titanium oxides, namely, anatase, brookite, corundum, and rutile, have been …

Go to article

Study Of Sn-Coated Graphite As Anode Material For Secondary Lithium-Ion Batteries, Basker Veeraraghavan, Anand Durairajan, Bala Haran, Branko N. Popov, Ronald Guidotti Jan 2002

Study Of Sn-Coated Graphite As Anode Material For Secondary Lithium-Ion Batteries, Basker Veeraraghavan, Anand Durairajan, Bala Haran, Branko N. Popov, Ronald Guidotti

Faculty Publications

Tin-graphite composites have been developed as an alternate anode material for Li-ion batteries using an autocatalytic deposition technique. The specific discharge capacity, coulombic efficiency, rate capability behavior, and cycle life of Sn-C composites has been studied using a variety of electrochemical methods. The amount of tin loading and the heating temperature have a significant effect on the composite performance. The synthesis conditions and Sn loading on graphite have been optimized to obtain the maximum reversible capacity for the composite electrode. Heating the composite converts it from amorphous to crystalline form. Apart from higher capacity, Sn-graphite composites possesses higher coulombic efficiency, …

Go to article

Modeling The Effects Of Electrode Composition And Pore Structure On The Performance Of Electrochemical Capacitors, Changqing Lin, Branko N. Popov, Harry J. Ploehn Jan 2002

Modeling The Effects Of Electrode Composition And Pore Structure On The Performance Of Electrochemical Capacitors, Changqing Lin, Branko N. Popov, Harry J. Ploehn

Faculty Publications

This work presents a mathematical model for charge/discharge of electrochemical capacitors that explicitly accounts for particle-packing effects in a composite electrochemical capacitor consisting of hydrous RuO2 nanoparticles dispersed within porous activated carbon. The model is also used to investigate the effect of nonuniform distributions of salt in the electrolyte phase of the electrode in the context of dilute solution theory. We use the model to compare the performance of capacitors with electrodes made from different activated carbons and to investigate the effects of varying carbon content and discharge current density. Even at low discharge current density, concentration polarization in …

Go to article

Modeling The Effects Of Electrode Composition And Pore Structure On The Performance Of Electrochemical Capacitors, Changqing Lin, Branko N. Popov, Harry J. Ploehn Jan 2002

Modeling The Effects Of Electrode Composition And Pore Structure On The Performance Of Electrochemical Capacitors, Changqing Lin, Branko N. Popov, Harry J. Ploehn

Faculty Publications

This work presents a mathematical model for charge/discharge of electrochemical capacitors that explicitly accounts for particle-packing effects in a composite electrochemical capacitor consisting of hydrous RuO2 nanoparticles dispersed within porous activated carbon. The model is also used to investigate the effect of nonuniform distributions of salt in the electrolyte phase of the electrode in the context of dilute solution theory. We use the model to compare the performance of capacitors with electrodes made from different activated carbons and to investigate the effects of varying carbon content and discharge current density. Even at low discharge current density, concentration polarization in …

Go to article

Electrochemical Generation Of Superoxide In Room-Temperature Ionic Liquids, Inas M. Alnashef, Matthew L. Leonard, Matthew C. Kittle, Michael A. Matthews, John W. Weidner Jan 2001

Electrochemical Generation Of Superoxide In Room-Temperature Ionic Liquids, Inas M. Alnashef, Matthew L. Leonard, Matthew C. Kittle, Michael A. Matthews, John W. Weidner

Faculty Publications

We have demonstrated that superoxide ion can be generated electrochemically in room-temperature ionic-liquid solvents. In the absence of impurities, cyclic voltammetry showed that the super oxide ion is stable in these solvents. Similar superoxide ion chemistry has previously been demonstrated in volatile and environmentally suspect aprotic solvents such as dimethyl formamide and acetonitrile. However, ionic liquids are nonvolatile and should minimize the problems of secondary solvent waste. It is proposed that the resultant superoxide ion can be used to perform low temperature oxidation of wastes. Low-temperature oxidation of waste solvents can provide a much needed alternative to high-temperature waste incinerators, …

Go to article

Hysteresis During Cycling Of Nickel Hydroxide Active Material, Venkat Srinivasan, John W. Weidner, John Newman Jan 2001

Hysteresis During Cycling Of Nickel Hydroxide Active Material, Venkat Srinivasan, John W. Weidner, John Newman

Faculty Publications

The nickel hydroxide electrode is known to exhibit a stable hysteresis loop, with the potential on charge being higher than that on discharge at every state-of-charge (SOC). What we show here is that this loop created during a complete charge and discharge (i.e., boundary curves) is not sufficient to define the state of the system. Rather, internal paths within the boundary curves (i.e., scanning curves) can be generated that access potentials between the boundary curves. The potential obtained at any SOC, as well as how the material charges and discharges from that point, depends on the …

Go to article

Synthesis And Characterization Of Hydrous Ruthenium Oxide-Carbon Supercapacitors, Manikandan Ramani, Bala S. Haran, Ralph E. White, Branko N. Popov Jan 2001

Synthesis And Characterization Of Hydrous Ruthenium Oxide-Carbon Supercapacitors, Manikandan Ramani, Bala S. Haran, Ralph E. White, Branko N. Popov

Faculty Publications

It is shown that composite Ru oxide-carbon based supercapacitors possess superior energy and power densities as compared to bare carbon. An electroless deposition process was used to synthesize the ruthenium oxide-carbon composites. Ru is dispersed on the carbon matrix as small particles. The effect of electrochemical oxidation and temperature treatment on the material performance has been studied extensively. Increasing the oxidation temperature reduces the proton transport rate and also increases the degree of crystallinity of the deposits. This adversely affects the performance of the composite. Loading a small amount of Ru oxide (9 wt %) on carbon increases the capacitance …

Go to article

Diffusion Of Water In Nafion 115 Membranes, Sathya Motupally, Aaron J. Becker, John W. Weidner Jan 2000

Diffusion Of Water In Nafion 115 Membranes, Sathya Motupally, Aaron J. Becker, John W. Weidner

Faculty Publications

In this paper, experimental and simulated data for the diffusion of water across Nafion membranes as a function of the water activity gradient are presented. The gradient in the activity of water across the membrane was varied by changing the flow rate and pressure of nitrogen gas on one side of the membrane. The other side of the membrane was equilibrated with liquid water. It was found that the model predictions are very sensitive to the value of the diffusion coefficient of water in Nafion. Using the Fickian diffusion coefficient extracted from self-diffusion measurements reported in the literature, the model …

Go to article

Modeling The Effects Of Ion Association On Direct-Current Polarization Of Solid Polymer Electrolytes, Changqing Lin, Ralph E. White, Harry J. Ploehn Jan 2000

Modeling The Effects Of Ion Association On Direct-Current Polarization Of Solid Polymer Electrolytes, Changqing Lin, Ralph E. White, Harry J. Ploehn

Faculty Publications

Considerable experimental evidence indicates that ion association occurs in solid polymer electrolytes. This work provides a thorough theoretical analysis of the effect of ion association on the conductivity, general current-potential behavior, and limiting current density in a solid polymer electrolyte. The model employs dilute solution theory to describe the fluxes of cations, anions, and ion pairs in a motionless continuum but neglects higher order association. The predictions of the model highlight the effects of the relative diffusion coefficients and dimensionless association constant on concentration distributions of simple ions and ion pairs, the limiting current density, and the potential drop required …

Go to article

Studies On The Capacitance Of Nickel Oxide Films: Effect Of Heating Temperature And Electrolyte Concentration, Venkat Srinivasan, John W. Weidner Jan 2000

Studies On The Capacitance Of Nickel Oxide Films: Effect Of Heating Temperature And Electrolyte Concentration, Venkat Srinivasan, John W. Weidner

Faculty Publications

Nickel oxide films were prepared by electrochemically precipitating the hydroxide and heating it in air to form the oxide. The resulting oxide films behave as a capacitor. The capacitance of the oxide depends on the heating temperature, showing a maximum at 300°C. The mechanism of charge storage was studied by measuring the capacitance and surface area as a function of heating temperature, and the capacitance in different electrolytes and potential windows. The charge-storage mechanism is believed to be a surface redox reaction involving adsorbed hydroxyl ions.

Go to article

Development Of A New Electrodeposition Process For Plating Of Zn-Ni-X (X = Cd, P) Alloys: I. Corrosion Characteristics Of Zn-Ni-Cd Ternary Alloys, Anand Durairajan, Bala S. Haran, Ralph E. White, Branko N. Popov Jan 2000

Development Of A New Electrodeposition Process For Plating Of Zn-Ni-X (X = Cd, P) Alloys: I. Corrosion Characteristics Of Zn-Ni-Cd Ternary Alloys, Anand Durairajan, Bala S. Haran, Ralph E. White, Branko N. Popov

Faculty Publications

A new Zn-Ni-Cd plating process was developed which offers a unique way of controlling and optimizing the Ni and Cd contents in the final deposit. Zinc-nickel-cadmium alloy was deposited from a 0.5 M NiSO4 + 0.2 M ZnSO4 bath in the presence of 0.015 M CdSO4 and 1 g/L nonyl phenyl polyethylene oxide. Using this process a Zn-Ni-Cd ternary alloy, with a higher nickel content as compared to that obtained from conventional Zn-Ni baths, was synthesized. The Zn-Ni-Cd alloy coatings deposited from an electrolyte containing 0.015 M (0.3%) CdSO4 has a Zn to Ni ratio of …

Go to article

Ni-Composite Microencapsulated Graphite As The Negative Electrode In Lithium-Ion Batteries Ii: Electrochemical Impedance And Self-Discharge Studies, P. Yu, James A. Ritter, Ralph E. White, Branko N. Popov Jan 2000

Ni-Composite Microencapsulated Graphite As The Negative Electrode In Lithium-Ion Batteries Ii: Electrochemical Impedance And Self-Discharge Studies, P. Yu, James A. Ritter, Ralph E. White, Branko N. Popov

Faculty Publications

Electrochemical impedance and self-discharge studies were carried out to investigate lithium intercalation into bare and Ni-coated KS10 graphite. Values of the charge-transfer resistances, exchange current densities, surface film resistances, and lithium-ion diffusion coefficients as functions of the state of charge (SOC) all favored the 10 wt % Ni composite KS10 graphite over bare KS10 graphite when these materials were used as the negative electrode in a Li-ion cell with mixed organic electrolyte. The charge-transfer resistances were always lower and gave rise to between 26 and 27% larger exchange current densities, which increased from 137 to 614 mA/g as the SOC …

Go to article

Computational Fluid Dynamics Modeling Of A Lithium/Thionyl Chloride Battery With Electrolyte Flow, W. B. Gu, C. Y. Wang, John W. Weidner, Rudolph G. Jungst, Ganesan Nagasubramanian Jan 2000

Computational Fluid Dynamics Modeling Of A Lithium/Thionyl Chloride Battery With Electrolyte Flow, W. B. Gu, C. Y. Wang, John W. Weidner, Rudolph G. Jungst, Ganesan Nagasubramanian

Faculty Publications

A two-dimensional model is developed to simulate discharge of a lithium/thionyl chloride primary battery. As in earlier one-dimensional models, the model accounts for transport of species and charge, and electrode porosity variations and electrolyte flow induced by the volume reduction caused by electrochemical reactions. Numerical simulations are performed using a finite volume method of computational fluid dynamics. The predicted discharge curves for various temperatures show good agreement with published experimental data, and are essentially identical to results published for one-dimensional models. The detailed two-dimensional flow simulations show that the electrolyte is replenished from the cell head space predominantly through the …

Go to article

Development Of A New Electrodeposition Process For Plating Of Zn-Ni-X (X = Cd, P) Alloys: Permeation Characteristics Of Zn-Ni-Cd Ternary Alloys, A. Durairajan, B. S. Haran, Ralph E. White, Branko N. Popov Jan 2000

Development Of A New Electrodeposition Process For Plating Of Zn-Ni-X (X = Cd, P) Alloys: Permeation Characteristics Of Zn-Ni-Cd Ternary Alloys, A. Durairajan, B. S. Haran, Ralph E. White, Branko N. Popov

Faculty Publications

It is shown that an electrodeposited Zn-Ni-Cd alloy coating produced from sulfate electrolyte inhibits the discharge of hydrogen on carbon steel. The newly developed ternary alloys have approximately ten times higher corrosion resistance when compared to a Zn-Ni alloy. Hydrogen permeation characteristics of Zn-Ni-Cd alloy coatings were studied and compared with those of a bare and a Zn-Ni alloy coated steel. The transfer coefficient, a, exchange current density, io, thickness dependent adsorption-absorption rate constant, k0, recombination rate constant, k3, surface hydrogen coverage, θH, were obtained by applying a mathematical model to experimental results. Alloys obtained from baths containing higher concentration …

Go to article

Modeling Lithium Intercalation Of A Single Spinel Particle Under Potentiodynamic Control, Dong Zhang, Branko N. Popov, Ralph E. White Jan 2000

Modeling Lithium Intercalation Of A Single Spinel Particle Under Potentiodynamic Control, Dong Zhang, Branko N. Popov, Ralph E. White

Faculty Publications

A mathematical model is presented for the lithium intercalation of a single spinel particle as a microelectrode under the stimulus of a cyclic linear potential sweep. The model includes both lithium diffusion within the particle and kinetics at the particle/electrolyte interface. The model is used to predict that peak current densities depend linearly on the scan rate to a certain power with a constant term, which is different from the predicted peak current density for a conventional redox system.

Go to article

Shrinking Core Model For The Discharge Of A Metal Hydride Electrode, Venkat R. Subramanian, Harry J. Ploehn, Ralph E. White Jan 2000

Shrinking Core Model For The Discharge Of A Metal Hydride Electrode, Venkat R. Subramanian, Harry J. Ploehn, Ralph E. White

Faculty Publications

A shrinking core model is presented for the galvanostatic discharge of a metal hydride particle. A quantitative criterion for when the shrinking core can be completely neglected or approximated by a pseudosteady-state solution is presented. The effect of shrinking of the core on the discharge behavior of a metal hydride particle is also studied.

Go to article

Analysis Of A Lithium/Thionyl Chloride Battery Under Moderate-Rate Discharge, Mukul Jain, Ganesan Nagasubramanian, Rudolph G. Jungst, John W. Weidner Jan 1999

Analysis Of A Lithium/Thionyl Chloride Battery Under Moderate-Rate Discharge, Mukul Jain, Ganesan Nagasubramanian, Rudolph G. Jungst, John W. Weidner

Faculty Publications

A one-dimensional mathematical model of a spirally wound lithium/thionyl chloride primary battery is developed and used for parameter estimation and design studies. The model formulation is based on the fundamental conservation laws using porous electrode theory and concentrated solution theory. The model is used to estimate the transference number, the diffusion coefficient, and the kinetic parameters for the reactions at the anode and the cathode as a function of temperature. These parameters are obtained by fitting the simulated capacity and average cell voltage to experimental data over a wide range of temperatures (–55 to 49°C) and discharge loads (10-250 ). …

Go to article

Determination Of The Lithium Ion Diffusion Coefficient In Graphite, Ping Yu, Branko N. Popov, James A. Ritter, Ralph E. White Jan 1999

Determination Of The Lithium Ion Diffusion Coefficient In Graphite, Ping Yu, Branko N. Popov, James A. Ritter, Ralph E. White

Faculty Publications

A complex impedance model for spherical particles was used to determine the lithium ion diffusion coefficient in graphite as a function of the state of charge (SOC) and temperature. The values obtained range from of 1.12 × 10–10 to 6.51 × 10–11 cm2/s at 25°C for 0 and 30% SOC, respectively, and for 0% SOC, the value at 55°C was 1.35 × 10–10 cm2/s. The conventional potentiostatic intermittent titration technique (PITT) and Warburg impedance approaches were also evaluated, and the advantages and disadvantages of these techniques were exposed

Go to article

Material Balance Modification In One-Dimensional Modeling Of Porous Electrodes, Mukul Jain, John W. Weidner Jan 1999

Material Balance Modification In One-Dimensional Modeling Of Porous Electrodes, Mukul Jain, John W. Weidner

Faculty Publications

The material balance used previously in one-dimensional mathematical models of porous electrodes is invalid when there is a non-zero volume change associated with the reaction. It is shown here how the material balance should be modified either to account for a loss in volume, or to account for an inflow of electrolyte from the header into the active pores. A one-dimensional mathematical model is used to illustrate the effect of this correction on the prediction of the delivered capacity and the electrolyte concentration in a lithium/thionyl chloride primary battery.

Go to article

Correlation Of Double-Layer Capacitance With The Pore Structure Of Sol-Gel Derived Carbon Xerogels, Chuan Lin, James A. Ritter, Branko N. Popov Jan 1999

Correlation Of Double-Layer Capacitance With The Pore Structure Of Sol-Gel Derived Carbon Xerogels, Chuan Lin, James A. Ritter, Branko N. Popov

Faculty Publications

Nine different sol-gel derived carbon xerogels were prepared with different pore structures by varying the carbonization temperature (in flowing N2) and activation time (in 5% CO2 in N2). For each of these carbon xerogels, mesopore and micropore size distributions and cumulative surface areas were extracted from a density functional theory analysis. Increasing the carbonization temperature caused a decrease in the number of micropores in the 6 Å range but had little effect on the mesopore size distribution and thus mesopore cumulative surface area. Increasing the CO2 activation time caused an increase in the number …

Go to article

First Prev Next Last