Chemical Engineering Commons^™

A New Deep Decoder Type Cascaded Feedforward Neural Network For Critical Heat Flux Prediction In Power Reactors, Rehan Zubair Khalid, Atta Ullah, Asifullah Khan, Mansoor Hameed Inayat, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

Critical Heat Flux (CHF) is a fundamental parameter for ensuring the performance, reliability, safety, and economic viability of water-cooled nuclear reactors. Despite its significance, the absence of a deterministic theory for CHF prediction poses a substantial challenge in thermal engineering. Consequently, various experimental and numerical models have been developed, yet no universally accepted model comprehensively addresses the wide range of flow conditions encountered in practical applications. The accurate prediction of CHF remains a complex and critical task. This work introduces a novel Deep Decoder Type Cascaded feedforward Neural Network (DD-CFNN) to predict CHF across a broad spectrum of operating conditions. …

Evaluation Of Physical And Chemical Stability In Liposomes Composed Of Mixed Phospholipids, Sharareh Rezaei, Kenny Mineart

Master’s Theses

Liposomes, spherical vesicles composed of lipid bilayers, are widely used in drug delivery due to their biocompatibility, biodegradability, and ability to interact with biological membranes. Despite these advantages, liposomes remain moderately unstable systems, highly susceptible to environmental stressors such as pH fluctuations, ionic strength variations, temperature changes, and interactions with other components. Addressing both chemical and physical instability is essential for translating liposomal formulations from experimental formulation to viable pharmaceutical products.

This study investigates the physicochemical characteristics of a mixed-phospholipid system in which one lipid is saturated, and the other is unsaturated (DMPC and DOPC respectively). Liposomes are prepared using …

Polymorphism And Mechanical Behavior In Hot-Pressed 3d-Printed Polyamide Composite: Effects Of Pressure And Temperature, John Barber, Patricia Revolinsky, Jimesh Bhagatji, Diego Pedrazzoli, Sergii Kravchenko, Oleksandr Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

The aim of this work is to study the effect of high-temperature compaction (HTC) upon the polymorphism and the mechanical behavior of an additively manufactured (AM) carbon fiber-reinforced polyamide (PA6). Different pressure and temperature levels during HTC were tested to determine the overall effect on the mechanical behavior and material crystalline composition. Treated, carbon fiber-reinforced PA6 samples were analyzed using differential scanning calorimetry, X-ray diffraction, thermogravimetric analysis, scanning electron microscopy, and three-point bending testing. When considered with respect to as-printed samples, an HTC temperature of 190 °C combined with 80 psi pressure resulted in an increased flexural modulus and strength …

A Comprehensive Review Of Piezoelectric Pvdf Polymer Fabrications And Characteristics, Nadia Ahbab, Sidra Naz, Tian-Bing Xu, Shihai Zhang

Mechanical & Aerospace Engineering Faculty Publications

Polyvinylidene fluoride (PVDF) polymer films, renowned for their exceptional piezoelectric, pyroelectric, and ferroelectric properties, offer a versatile platform for the development of cutting-edge micro-scale functional devices, enabling innovative applications ranging from energy harvesting and sensing to medical diagnostics and actuation. This paper presents an in-depth review of the material properties, fabrication methodologies, and characterization of PVDF films. Initially, a comprehensive description of the physical, mechanical, chemical, thermal, electrical, and electromechanical properties is provided. The unique combination of piezoelectric, pyroelectric, and ferroelectric properties, coupled with its excellent chemical resistance and mechanical strength, makes PVDF a highly valuable material for a wide …

Challenges And Perspectives On Photocatalytic Membrane Reactors For Volatile Organic Compounds Degradation And Nitrogen Oxides Treatment, Muhammad Hassnain, Muhammad Rizwan Azhar, Asad Ali, Muhammad Mubashir, Abdulrahman Abutaleb

Research outputs 2022 to 2026

Air pollution is a pressing environmental and public health issue, with volatile organic compounds (VOCs) and nitrogen oxides (NOx) being among the most hazardous airborne pollutants. Photocatalytic membrane reactors (PMRs) have emerged as a promising technology for air purification due to their ability to integrate photocatalytic degradation and membrane separation in a single system. This paper provides a comprehensive review of the advancements, challenges, and future prospects of PMR technology for VOC degradation and NOx treatment. Various photocatalytic membranes and their fabrication techniques, including material selection, structural modifications, and catalyst immobilization strategies, are critically analyzed. The study further explores different …

A Pyrrole Modified 3,4-Propylenedioxythiophene Conjugated Polymer As Hole Transport Layer For Efficient And Stable Perovskite Solar Cells, Yuanhao Tang, Ke Ma, Wenhao Shao, Yoon Ho Lee, Ashkan Abtahi, Jiaonan Sun, Hanjun Yang, Aidan H. Coffey, Harindi R. Atapattu, Mustafa Ahmed, Qixuan Hu, Wenzhan Xu, Raunak Dani, Limei Wang, Chenhui Zhu, Kenneth R. Graham, Jianguo Mei, Letian Dou

Chemical and Materials Engineering Faculty Publications

Despite the outstanding electric properties and cost-effectiveness of poly- (3,4-ethylenedioxythiophene) (PEDOT) and its derivatives, their performance as hole transport layer (HTL) materials in conventional perovskite solar cells (PSCs) has lagged behind that of widely used spirobifluorene-based molecules or poly(triaryl amine). This gap is mainly from their poor solubility and energy alignment mismatch. In this work, the design and synthesis of a pyrrole-modified HTL (PPr) based on 3,4-propylenedioxythiophene (ProDOT) are presented for efficient and stable PSCs. As a result of the superior defects passivation ability, excellent contact with perovskite, enhanced hole extraction, and high hydrophobicity, the unencapsulated PPr-based PSCs showed the …

Analysis Of Tar And Oil Derived From Pyrolysis And Copyrolysis Of Waste Plastics And Biomass, Anitha Shankaralinge Gowda, Dimitrios Karadimas, Jeffrey Seay

Chemical and Materials Engineering Faculty Publications

Pyrolysis has been proposed as a potential technology for managing the growing volume of plastic waste generated worldwide. Co-pyrolysis of plastic waste with biomass is a promising technology for generating fuel and chemical products. However, this process generates tar as a waste product. The chemical properties of this tar have yet to be thoroughly analyzed. This study presents the results of gas chromatography–mass spectrometry (GC–MS), Fourier-transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA) of oil and tar obtained from the pyrolysis of pure plastics including high-density polyethylene (HDPE), low-density polyethylene (LDPE), polyethylene (PE), polystyrene (PS), and plastic-biomass mixtures. GC–MS analysis …

Membrane Filtration Of Nanoscale Biomaterials: Model System And Membrane Performance Evaluation For Aav2 Viral Vector Clarification And Recovery, Mara Leach, Kearstin Edmonds, Emily Ingram, Rebecca E. Dutch, Ranil Wickramasinghe, Malgorzata Chwatko, Dibakar Bhattacharyya

Chemical and Materials Engineering Faculty Publications

The growing demand for viral vectors as nanoscale therapeutic agents in gene therapy necessitates efficient and scalable purification methods. This study examined the role of nanoscale biomaterials in optimizing viral vector clarification through a model system mimicking real AAV2 crude harvest material. Using lysed HEK293 cells and silica nanoparticles (20 nm) as surrogates for AAV2 crude harvest, we evaluated primary (depth filters) and secondary (membrane-based) filtration processes under different process parameters and solution conditions. These filtration systems were then assessed for their ability to recover nanoscale viral vectors while reducing DNA (without the need for endonuclease treatment), protein, and turbidity. …

Fundamental And Application Of Co-Assembly Of Peptides And Proteins: Experiment And Computation, Newton A. Ihoeghian, Qing Shao

Chemical and Materials Engineering Faculty Publications

Peptides and proteins can co-assemble into various nanostructures based on complementary non-covalent interactions such as electrostatic forces, hydrogen bonding, and hydrophobic associations. These co-assemblies create a design space of functional materials for a wide spectrum of energy, environmental, and biomedical applications. This review focuses on the fundamentals and applications of three co-assembling systems: ultra-short peptides, peptides, and proteins. We will present and discuss experimental studies demonstrating applications in drug delivery, tissue engineering, and biomaterials development. We will also discuss the contribution of computational research, including molecular dynamics simulations and machine learning, to enhance our understanding of assembly mechanisms. Integrating experimental …

Metathesis Or Isomerization: Counteranion Directed Reactivity Of Grubbs I, Paul D. Miller, Joe B. Calkins, Craig A. Bayse, Trandon A. Bender

Chemistry & Biochemistry Faculty Publications

Catalytic isomerization of alkenes has garnered interest for many years, but there are remaining challenges when it comes to thermodynamic selectivity and uncontrolled isomerization. Nonbiased substrates, be it sterically or thermodynamically, remain challenging for many catalysts, with a few examples available in the more modern literature. Herein, we present the controlled isomerization of linear alkenes with a cocatalytic mixture of commercially available catalyst and reagents: Grubbs I, tris(pentafluorophenyl)borane, and triethylsilane. DFT calculations indicate that an observed alkylidyne hydride intermediate is in rapid equilibrium with an alkylidene that binds the alkene substrate. This combination results in a pi-acidic metal and a …

Electrical Homeostasis Of The Inner Mitochondrial Membrane Potential, Peyman Fahimi, Lázaro A. M. Castanedo, P. Thomas Vernier, Cherif F. Matta

Bioelectrics Publications

The electric potential across the inner mitochondrial membrane must be maintained within certain bounds for the proper functioning of the cell. A feedback control mechanism for the homeostasis of this membrane potential is proposed whereby an increase in the electric field decreases the rate-limiting steps of the electron transport chain (ETC). An increase in trans-membrane electric field limits the rate of proton pumping to the inter-membrane gap by slowing the ETC reactions and by intrinsically induced electroporation that depolarizes the inner membrane. The proposed feedback mechanism is akin to a Le Chatelier's-type principle of trans-membrane potential feedback control.

Predicting The State Of Health Of Samsung 25r Lithium Ion Batteries, Matthew O'Donnell

Open Access Master's Theses

This thesis may contain material at the Controlled Unclassified Information (CUI) level. The full document cannot be released.

Fluid Pathways For Enhanced Mass Transfer In The Micro Regime: Applications In Novel Pumpless Redox Flow Cell And Zinc Finger Protein-Based Dna Detection, Shaikh Al Mahmud Bhuiyan

Theses and Dissertations--Mechanical and Aerospace Engineering

Precise fluid transport through microscale geometries can help optimize electrochemical and biochemical processes by maximizing the mass transfer rate of reactants. By introducing intricate structural features inside microchannels, it is possible to manipulate the fluid motion and direct the flow towards any surface of interest. In this study, we have demonstrated that rationally designed fluid pathways can improve the performance of electrochemical and biochemical systems.

The emergence of additive manufacturing has enabled rapid fabrication of robust structures with intricate features to guide fluid motion. However, their application in nonaqueous electrochemical systems has been limited due to their interaction with organic …

Chondrogenic And Chondroprotective Response Of Composite Collagen I/Ii-Hyaluronic Acid Scaffolds Within An Inflammatory Osteoarthritic Environment, Carly M. Battistoni, Javier Munoz Briones, Douglas K. Brubaker, Alyssa Panitch, Julie C. Liu

School of Chemical Engineering Faculty Publications

Inflammation plays a key role in cartilage damage that occurs in osteoarthritis (OA). However, in vitro assessments of tissue-engineered constructs for cartilage regeneration generally do not consider their performance in the presence of inflammation. In this work, the chondrogenic differentiation potential of mesenchymal stromal cells (MSCs) was evaluated in the presence of both chondrogenic factors and inflammatory cytokines, and cartilage formation, degradative response, and inflammatory response were characterized. The addition of cytokines reduced cartilage production, increased cell proliferation, and resulted in an increase in inflammatory markers. Incorporation of hyaluronic acid (HA) had little impact on both collagen fibril microstructure and …

Life Cycle Assessment Of Renewable Hydrocarbon Fuels Produced By The New Cool Gas To Liquid (Cool Gtl) Process, Elochukwu Okoye

Dissertations, Master's Theses and Master's Reports

The Cool Gas-to-Liquid (Cool GTL) process converts biogas and captured CO₂ into renewable hydrocarbon fuels, contributing to GHG emissions reduction in transportation. This report explains a Life Cycle Assessment (LCA) study that was completed to evaluate the environmental impact of different feedstocks, hydrogen sources, and electricity inputs. The analysis considers biogas from food waste, manure, and landfill sources, as well as biogenic, fossil, and direct air capture (DAC) CO₂ feedstocks. Results show that biogas pathways provide the greatest GHG reductions, with the best case (food and manure biogas + solar hydrogen + solar electricity) achieving a net-negative GWP …

Supercapacitors With Cotton Shell-Derived Activated Carbons And Porous Polymer Electrolyte Films, Saurabh Singh, Yulin Zhang, S. A. Hashmi, Fuqian Yang

Chemical and Materials Engineering Faculty Publications

Some of the well-known challenges in the field of supercapacitors (SCs), or more specifically, electrical double-layer capacitors (EDLCs), such as low energy density and high cost, have proven to be major barriers to their widespread market success despite having some excellent electrochemical merits such as high-power density and good cyclic stability. In this work, efforts have been made to overcome these gaps and eventually enhance the performance of EDLCs via a cost-effective and eco-friendly approach. To fabricate these EDLCs, a bio-waste, namely, cotton-shell-derived activated carbons (ZnACs) (activated with ZnCl2), was used in a mass ratio of 1 : 2 for …

Improvement Of Cellular Pattern Organization And Clarity Through Centrifugal Force, Lauren E. Mehanna, James D. Boyd, Shelley Remus-Williams, Nicole M. Racca, Dawson P. Spraggins, Martha E. Grady, Brad J. Berron

Chemical and Materials Engineering Faculty Publications

Rapid and strategic cell placement is necessary for high throughput tissue fabrication. Current adhesive cell patterning systems rely on fluidic shear flow to remove cells outside of the patterned regions, but limitations in washing complexity and uniformity prevent adhesive patterns from being widely applied. Centrifugation is commonly used to study the adhesive strength of cells to various substrates; however, the approach has not been applied to selective cell adhesion systems to create highly organized cell patterns. This study shows centrifugation as a promising method to wash cellular patterns after selective binding of cells to the surface has taken place. After …

Integrating Protein Language Model And Molecular Dynamics Simulations To Discover Antibiofouling Peptides, Ibrahim A. Imam, Shea Bailey, Duolin Wang, Shuai Zeng, Dong Xu, Qing Shao

Chemical and Materials Engineering Faculty Publications

Antibiofouling peptide materials prevent the nonspecific adsorption of proteins on devices, enabling them to perform their designed functions as desired in complex biological environments. Due to their importance, research on antibiofouling peptide materials has been one of the central subjects of interfacial engineering. However, only a few antibiofouling peptide sequences have been developed. This narrow scope of antibiofouling peptide materials limits their capacity to adapt to the broad spectrum of application scenarios. To address this issue, we searched for antibiofouling peptides in the vast sequence pool of the microbiome library using a combination of deep learning-based high-throughput search and molecular …

Clarifying The Role Of Η-Phase With Varying Chemistry On Localised Corrosion Of A Cu-Containing 7xxx Al-Alloy By Quasi-In-Situ Tem, S. K. Kairy, Y. Wu, S. Turk, A. Shekhter, Rudolph Buchheit, N. Birbilis

Chemical and Materials Engineering Faculty Publications

Quasi-in-situ transmission electron microscopy was employed to study dissolution associated with η-phase (Mg(Zn,Al,Cu)₂) precipitates in a Cu-containing 7xxx Al-alloy. Two distinct η-phase chemistries, with Cu to (Zn+Mg+Al) ratios ∼0.12 and ∼0.2, were studied in 0.01 M NaCl at pH 6 and 2. In near-neutral NaCl, both η-phase precipitates exhibited ‘duplex’ behaviour, i.e., they were primarily more noble with respect to the surrounding Al-matrix, causing matrix dissolution, and simultaneously established nanoscopic active sites within the noble precipitate itself by generating nanoscale pits. Conversely, η-phase precipitates rapidly dealloyed in acidic NaCl, forming nocrystalline Cu remnants containing twins, which subsequently caused …

Enhancing Intrinsic Ductility In Vnbmotaw High Entropy Alloy: A Combinatorial Investigation With Experimental Evaluation Of Theoretical Predictions, Taohid Bin Nur Tuhser, Ian Stewart Winter, Daryl Chrzan, Thomas John Balk

Chemical and Materials Engineering Faculty Publications

The application of refractory high entropy alloys (RHEAs) as engineering materials has been hindered by their poor inherent ductility. In this study, a novel approach combining thin film combinatorial screening with fragmentation testing was employed to identify intrinsically ductile alloy compositions. Inspired by the physics-based intrinsic ductility parameter, the ‘χ-parameter,’ we investigated the replacement of group VI elements (W/Mo) with group V elements (V, Nb, Ta) in the VNbMoTaW system. Conventional combinatorial analyses, including composition, phase, and hardness assessments, were conducted across a wide range of non-equiatomic configurations. The results revealed a broad compositional space favoring a single-phase body-centered cubic …

Valorizing Municipal Solid Waste For Sustainable Aviation Fuel And Polyhydroxyalkanoate Bioplastics: Pyrolysis And Microbial Pathways, Emon Das

Theses and Dissertations--Biosystems and Agricultural Engineering

The escalating global burden of municipal solid waste (MSW), projected to reach 3.88 billion tons annually by 2050, calls for innovative valorization strategies to mitigate environmental impacts and promote a circular bioeconomy. This thesis investigates the conversion of MSW into two high-value products: sustainable aviation fuel (SAF) and polyhydroxyalkanoate (PHA) bioplastics. Chapter one presents comprehensive physicochemical characterization and pyrolysis-GC/MS analysis of MSW feedstocks. The physicochemical results reveal that densification enhances handling and storage properties, while pyrolysis-GC/MS analysis indicates that plastic-rich MSW streams produce bio-oils with favorable hydrocarbon profiles suitable for SAF production, potentially contributing to decarbonization efforts in the aviation …

How Many Passes Does It Take? An Investigation To Determine The Optimal Number Of Liposome Extrusion Cycles, Kasey Piper

Honors Theses

Liposomes are lipid-based nanoparticles with significant applications in drug delivery and membrane research. One of the most common methods for fabricating liposomes of specific sizes is membrane extrusion, where liposomes are passed through porous membranes to reduce their size. The precise number of passes needed and the factors influencing this process remain unclear. This thesis investigates the relationship between the number of passes through a track-etched polycarbonate membrane and size and lamellarity of extruded liposomes with a focus on lipid type (DOPC, DMPC, Soy PC), membrane pore size (50, 100, 200, 400 nm), and the effect of freeze-thaw cycling. To …

Nanotube Spectral Fingerprinting And Machine Learning For Optimized Bioimaging/Sensing And Disease Detection Applications In Als, Rodrigo Monroy Lopez

Open Access Master's Theses

Single-walled carbon nanotubes (SWCNTs) possess unique physicochemical and optical properties that make them ideal candidates for biomedical imaging, biosensing, and disease diagnostics. This thesis explores the potential of SWCNT-based spectral fingerprinting combined with ML (Machine Learning) algorithms to optimize bioimaging, disease detection and prediction, with a specific focus on differentiating between healthy and amyotrophic lateral sclerosis (ALS) lymphoblastic patient samples. By functionalizing SWCNTs with single-stranded DNA, we enhance their stability and target specificity, enabling their application in serum patient samples.

A comprehensive spectral analysis of DNA-SWCNTs was conducted using near-infrared fluorescence spectroscopy and other characterization techniques, including UV-Vis-absorption spectroscopy. The …

Valorization Of Biomass Derivatives To Monomers By M-Mox Catalytic Hydrogenation & Hydrodeoxygenation, William Steere, Samir Castilla-Acevedo, Ben Auer, John Styers, Alan Allgeier

UNH URC Open (2026 and after)

With increasing concern regarding global warming contributions by fossil fuels in petrochemical production, the potential use of biomass-derived molecules to serve as a more eco-friendly feedstock has grown in popularity. Specifically, sebacic acid, a versatile chemical used to produce nylons, plasticizers, and lubricants, has the potential to be obtained from bio-renewable feedstocks and alleviate environmental drawbacks from fossil fuel petrochemical production. Our research validates the catalytic conversion of the biomass-derived 2,2’-bifuran 5,5’-dicarboxylate (BFDCM) to sebacic acid (SA), through M-MO_x catalyzed hydrogenation and hydrodeoxygenation. Catalytic activity tests were conducted for four different Pd-supported catalysts (C, Al₂O₃, …

Emulsion Liquid Membrane (Elm) Technique For Efficient Separation Of Heavy Metals From Acidic Solutions Including Phosphoric Acid: A Review, O. Karai, N. Y. Selem, K. Benabderazak, J. Mendil, H. Mazouz, M. H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

Heavy metal ions in aqueous and acidic solutions pose serious threats to ecosystems. Their effective removal is crucial, and emulsion liquid membrane (ELM) technology offers a promising solution. This review delves into ELM's principles, mechanisms, components, and performance indicators including stability for extracting heavy metals from acidic solutions including phosphoric acid., ELM's stability issues, such as internal phase coalescence, membrane leakage, and swelling, limit its efficiency. Thus, this review paper discusses previous research that analyzed ELM stability and heavy metal extraction efficiency from these acidic solutions. Furthermore, it assesses other techniques like Emulsion Ionic Liquid Membrane (EILM) and Pickering Emulsion …

Enhanced Cholesterol Efflux And Atherosclerosis Regression Via Ceh Gene Delivery Using Galactose-Functionalized Dendrimeric Nanoparticles, Huari Kou, Jing Wang, Paul J. Yannie, Da Huang, William J. Korzun, Genta Kakiyama, Siddhartha S. Ghosh, Hu Yang

Chemical and Biochemical Engineering Faculty Research & Creative Works

Cholesteryl ester hydrolase (CEH) is a critical enzyme in cholesterol ester hydrolysis, influencing cholesterol metabolism and efflux. This study demonstrates that CEH overexpression promotes free cholesterol efflux from macrophages, thereby reducing the lipid burden in existing atherosclerotic plaques. To enable targeted delivery, galactose-functionalized polyamidoamine (PAMAM) dendrimeric nanoparticles were utilized as nanocarriers for hepatic delivery of the CEH expression vector. The therapeutic potential of CEH plasmid-loaded dendrimeric nanoparticles was evaluated in Ldlr-/- mice. Results showed a significant reduction in total lesion area (21%) and aortic arch lesion area (23%) compared to baseline. Lesion component analysis revealed marked decreases in total cholesterol …

Statistical Investigation Of Gypsum Crystallization Kinetics, Azmain A. Akash

LSU Master's Theses

Gypsum, a naturally occurring mineral salt, is frequently encountered in industrial processes such as seawater desalination and power plant cooling. Over the years, significant effort has been devoted to controlling the crystallization of gypsum through various chemical approaches, including acidification, chelating agents, and antiscalant polymers. Nevertheless, the cost associated with chemical treatments may be reduced by incorporating physical operational strategies to complement chemical methods in regulating gypsum crystallization.

This study systematically examines the comparative roles of chemical and physical entropy in the gypsum crystallization process to elucidate their respective influences on gypsum growth kinetics. Chemical entropy is manipulated by adjusting …

Membrane Reactor Modeling And Optimization For Hydrogen Production, Ayooluwa Tomiwa Akintola

Graduate Theses, Dissertations, and Problem Reports (ETD)

There has been an ongoing trend toward cleaner fuels for more environmentally benign forms of energy generation. Recently, hydrogen has been identified as a clean fuel for energy generation. However, the most established, efficient, and widely utilized technique for producing hydrogen remains the steam methane reforming (SMR) in the presence of catalyst. Unlike other fossil fuels, utilizing methane from natural gas in an SMR process to produce hydrogen emits less, but yet a notable sum of carbon dioxide. Furthermore, the endothermic nature of SMR reactions imply that there is a high energy requirement to obtain a substantial amount of hydrogen …

Engineering Nanomaterials From Phase-Change Biological Materials Reacting With Carbon Dioxide, Qingyang Li

Graduate Theses, Dissertations, and Problem Reports (ETD)

The current global situation concerning CO2 emissions is increasingly alarming, with rising concentrations of CO2 significantly worsening climate change and global warming. Atmospheric CO2 levels are now at their highest in millions of years, driving a host of catastrophic effects, including but not limited to extreme weather events, rising sea levels, ocean acidification, disrupted ecosystems, deteriorating air quality, respiratory health issues, heat-related illnesses, threats to food and water security, and escalating social and geopolitical tensions. To keep global warming to no more than 1.5°C higher than that of pre-industry – as called for in the Paris Agreement – emissions need …

Expanding The Vibrating Sharp-Edge Spray Ionization Toolkit For Oligonucleotide Characterization, Sultan Mahmud

Graduate Theses, Dissertations, and Problem Reports (ETD)

A gentle or soft Ionization process is a critical component in native mass spectrometry (MS) to lift the biomolecules from the bulk solution into the gas phase environment of the mass spectrometer preserving their shape, topology and non-covalent interactions. Electrospray ionization (ESI) facilitates structural preservation of proteins, nucleic acids and their complexes and as a result it has been extensively used in native MS. However, in negative ion mode, ESI is somewhat limited in sensitivity due to corona discharge effect resulting from the requirement of a high amount of voltage. This often disrupts the ESI process and may not preserve …