Chemical Engineering Commons^™

Antiviral Polymers: A Review, Ali Akbari, Ashkan Bigham, Vahid Rahimkhoei, Sina Sharifi, Esmaiel Jabbari

Faculty Publications

Polymers, due to their high molecular weight, tunable architecture, functionality, and buffering effect for endosomal escape, possess unique properties as a carrier or prophylactic agent in preventing pandemic outbreak of new viruses. Polymers are used as a carrier to reduce the minimum required dose, bioavailability, and therapeutic effectiveness of antiviral agents. Polymers are also used as multifunctional nanomaterials to, directly or indirectly, inhibit viral infections. Multifunctional polymers can interact directly with envelope glycoproteins on the viral surface to block fusion and entry of the virus in the host cell. Polymers can indirectly mobilize the immune system by activating macrophages and …

Comparison Of Bio-Mass To Bio-Oil Reactor Systems: Direct Conversion Vs. Companion Coal Gasification, Luci Evans

Honors Theses

The purpose of this project was to define, design, and optimize the economic feasibility of the production of bio-oil from a direct conversion of biomass to bio-oil using fast pyrolysis and a secondary side reaction of the production of a syngas from coal gasification. In the end, a combined process of these two was created to show the new strengths and more efficient options to produce a desired product within a budget. The main objectives of this project were to research the economic feasibility of the biomass and bio-oil industry, obtain a market survey, design two process flow diagrams showing …

Editorial For Gels 6th Anniversary Special Issue, Esmaiel Jabbari, Gulden Camci-Unal

Faculty Publications

Note: In lieu of an abstract, this is an excerpt from the first page.

This Special Issue celebrates many outstanding quality papers published in Gels over the past six years since its first issue was published in 2015 [...]

Investigation On The Effect Of Binders On The Performance Of Si-Based Anodes Of Lithium-Ion Batteries, Christopher Rohen

Honors Theses

For the production of lithium-ion batteries with the different binders, a few things must be considered. The process of production has several steps. First is the preparation of the slurry with the composition of 70/10/20, 70% active material, 10% carbon black and 20% selected binder. Then, the bar coating of the slurry into a copper sheet is required. After drying in the oven, the sample in the cooper sheet, a few holes on the sample are made and the half-cell assembly. Lastly, the cell is assembled and its subject of rigorous testing to determine performance and stability; A few of …

Assembly Of Nanostructures At Solid-Liquid And Liquid-Air Interfaces, Yingzhen Ma

LSU Doctoral Dissertations

Molecular and nanoscale colloids such as surfactant, fatty acid and metallic nanoparticles are widely used in numerous applications such as detergents, biomedicine, and catalyst. The assemblies of these colloids show different morphological behavior in aqueous solution due to the wide range of intermolecular interactions such as hydrogen bonding, van der Waals, and electrostatics. The morphology of these assemblies can be changed by environmental factors including temperature, ionic strength, and salinity. However, the guidance to direct assembled state of colloidal assemblies at heterogenous interfaces under various external stimuli remains poorly understand. In this Ph.D. dissertation, we show the adsorption and reconfiguration …

Novel Thermal Coating For High-Speed Airplanes, Abinash Satapathy, Lakshay Battu, Liam Watson, Nazanin Rajabi

Symposium of Student Scholars

In comparison to various other materials, Carbon Fiber, specifically Carbon Fiber Reinforced Polymers (CFRP), is pre-eminent amongst other materials for use on aeronautical systems. Due to its high specific strength (strength-to-weight ratio), CFRP is prominent for carrying heavy loads while maintaining a lightweight build. However, when influenced by heat resulting from air resistance, CFRP is known to undergo serious degradation that would significantly decrease the effectiveness of the polymers. To prevent this degradation and maintain the strength of the CFRP, thermal protective layers (TPLs) are designed to shield the CFRP from heat exposure. This research is focused on the examination …

Determination Of The Heating Time Constant For Root Crops, Z K. Ergasheva, Beraat Ozcelik

Technical science and innovation

Convective drying refers to one of the energy-intensive processes used in chemical, woodworking, food and other industries. Therefore, in modern conditions, when there is a growing shortage and an increase in energy tariffs, it is important to develop and apply new effective methods of drying wet materials in industrial production, create high-performance drying equipment, improve the operation of existing dryers, which will contribute to the rational use of natural resources, reduce the cost of finished products and increase the competitiveness of production. Root crops are plants in which nutrients are concentrated in tubers or roots. Jerusalem artichoke refers to sugar-containing …

The Effect Of Chitosan On The Surface Properties Of Cellulose-Based Paper Obtained From The Stem Of Flaxseed, E A. Egamberdiev, Y T. Ergashev, Kh Kh Khaydullaev, G Y. Akmalova, G R. Rakhmonberdiev

Technical science and innovation

This paper examines the effects of chitosan, starch, and polyvinyl alcohol (PVA) to improve the surface properties of cellulose-based paper obtained from local raw materials. The polymers are incorporated into the paper polythene by spraying. The results showed that the addition of chitosan to paper polythene, which is made of cellulose fibers, has an improvement in surface properties compared to the effect of other additives. The degree of exposure of starch coincided with the degree of exposure of chitosan, but it resulted in a decrease in the water absorption potential of the paper compared to chitosan at the same concentration. …

Limits Of Detection Of Mycotoxins By Laminar Flow Strips: A Review, Xinyi Zhao, Hugh Byrne, Christine M. O’Connor, James Curtin, Furong Tian

Articles

Mycotoxins are secondary metabolic products of fungi. They are poisonous, carcinogenic, and mutagenic in nature and pose a serious health threat to both humans and animals, causing severe illnesses and even death. Rapid, simple and low-cost methods of detection of mycotoxins are of immense importance and in great demand in the food and beverage industry, as well as in agriculture and environmental monitoring, and, for this purpose, lateral flow immunochromatographic strips (ICSTs) have been widely used in food safety and environmental monitoring. The literature to date describing the development of ICSTs for the detection of different types of mycotoxins using …

Simplified Thermal Runaway Model For Assisting The Design Of A Novel Safe Li-Ion Battery Pack, Paul T. Coman, Eric C. Darcy, Ralph E. White

Faculty Publications

This paper presents a simplified thermal runaway model (FEM) used to guide the design of a novel battery pack designed to resist thermal runaway propagation passively. The model is based on the heat equation for a 2D geometry with a heat generation term based on the maximum amount of energy measured using a custom-made calorimeter. The model was validated against experimental data using a 48-cell subscale of a full-scale battery pack for three different runs with three trigger cells with Internal Short Circuit Devices (ISCD) implanted in the separators. One trigger cell was placed at the edge, one placed in …

Feasibility Study Of Implementing Gamma-Ray Computed Tomography On Measuring Aggregate Distribution And Radiation Shielding Properties Of Concrete Samples, Omar Farid, Nima Farzadnia, Kamal Khayat, Muthanna H. Al-Dahhan

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Aggregate segregation is one of the key defects that impair the performance of concrete at fresh and hardened stages. This study aims to assess the feasibility of using an advanced technique to identify/scan/determine the aggregate segregation of concrete elements and determine radiation shielding properties of the concrete. The gamma-ray computed tomography (γ-CT) technique was employed to study aggregate distribution/dispersion in self-consolidating concrete (SCC). Accordingly, two SCC mixtures with moderate segregation (MS) and high segregation (HS) levels were cast and compared with highly stable SCC with no segregation (NS). The γ-CT scans were located on three different levels of concrete specimens …

Assessment Of Wettability And Rock-Fluid Interfacial Tension Of Caprock: Implications For Hydrogen And Carbon Dioxide Geo-Storage, Muhammad Ali, Bin Pan, Nurudeen Yekeen, Sarmad Al-Anssari, Amer Al-Anazi, Alireza Keshavarz, Stefan Iglauer, Hussein Hoteit

Research outputs 2022 to 2026

Underground hydrogen (H2) storage (UHS) and carbon dioxide (CO2) geo-storage (CGS) are prominent methods of meeting global energy needs and enabling a low-carbon global economy. The pore-scale distribution, reservoir-scale storage capacity, and containment security of H2 and CO2 are significantly influenced by interfacial properties, including the equilibrium contact angle (θE) and solid-liquid and solid-gas interfacial tensions (γSL and γSG). However, due to the technical constraints of experimentally determining these parameters, they are often calculated based on advancing and receding contact angle values. There is a scarcity of θE, γSL, and γSG data, particularly related to the hydrogen structural sealing potential …

Reactive Oxygen Species (Ros)-Responsive Size-Reducible Nanoassemblies For Deeper Atherosclerotic Plaque Penetration And Enhanced Macrophage-Targeted Drug Delivery, Jianhua He, Wenli Zhang, Xiaoju Zhou, Fengfei Xu, Jiahui Zou, Qiqi Zhang, Yi Zhao, Hongliang He, Hu Yang, Jianping Liu

Chemical and Biochemical Engineering Faculty Research & Creative Works

Nanoparticle-based therapeutics represent potential strategies for treating atherosclerosis; however, the complex plaque microenvironment poses a barrier for nanoparticles to target the dysfunctional cells. Here, we report reactive oxygen species (ROS)-responsive and size-reducible nanoassemblies, formed by multivalent host-guest interactions between β-cyclodextrins (β-CD)-anchored discoidal recombinant high-density lipoprotein (NP³_ST) and hyaluronic acid-ferrocene (HA-Fc) conjugates. The HA-Fc/NP³_ST nanoassemblies have extended blood circulation time, specifically accumulate in atherosclerotic plaque mediated by the HA receptors CD44 highly expressed in injured endothelium, rapidly disassemble in response to excess ROS in the intimal and release smaller NP³_ST, allowing for further …

Chitosan/Polyacrylamide Green Gels For Water Control In High-Temperature Reservoirs, Mohamed Shamlooh, Reem Elaf, Ibnelwaleed A. Hussein, Mohammed Saad, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The rheology of a gel system composed of polyacrylamide (PAM) and chitosan is studied under typical reservoir conditions. The impacts of the degree of chitosan deacetylation, temperature, and salinity on the gelation behavior are assessed. The said system was prepared under ambient conditions and matured for 24 h at altered temperatures ranging from 50 up to 125 °C. An optimum formulation has been identified considering the rheological response and the initial viscosity constraints. The increase in the degree of syneresis with the degree of deacetylation indicates the long-Term thermal stability of the gels. Ammonium chloride was an effective retarder for …

Studying Dispersed Phase Holdup In A Pilot Plant Agitated Liquid–Liquid Mixer By Developing Online Expanded Laser Beam Based Technique, Kifah H. Abid, Jihane Mendil, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

Expanded Laser Transmission Technique (E-LTT), where a laser beam is used in conjunction with a beam expander large enough to cover the average drop size up to a few millimeters in the path of the laser in a liquid–liquid dispersion mixture, has been applied for online continuous measurement and investigation in a non-invasive manner of the drop phase volume fraction in an agitated flow mixer of a pilot plant scale. The limitations of beam scattering by the drops through the dispersion path were overcome by having liquids of matching refractive indices enabled by the temperature control system. This study reports …

Development & Validation Of A Piv System For Obtaining Data From A Uasb Reactor, Camila D' Bastiani, Gerald Gallagher, David Kennedy, Anthony Reynolds

Conference Papers

Anaerobic digestion processes can generate energy in the form of biogas while treating organic wastewater. The efficiency of the treatment, and thus the generation of biogas, is closely linked to the type and design of the reactor, and the technology used. Granular anaerobic digestion technology offers advantages such as a higher loading rate and reduction of the space needed. However, the hydrodynamics inside this type of reactor can be complex due to the presence of solids (granules) and gas (biogas) phases along with the liquid phase (wastewater). This is one of the reasons why the study and optimization of reactors …

Model-Guided Design Of Rna-Based Synthetic Circuits For The Dynamic Regulation Of Gene Expression, Jordan R. Ryan

LSU Master's Theses

A longstanding goal in synthetic biology has been to build synthetic gene circuits with the ability to harness nature’s capability of precise gene expression regulation. Advancements in RNA technology have established RNA-based regulators with distinct advantages over traditional protein-based regulators such as faster signal propagation, versatile programmability, and low cellular burden, which has created an interest in the field to construct innovative synthetic gene circuits using de novo RNA- based regulators. However, our understanding of the behavior and kinetics of RNA-RNA interactions for the construction of gene circuits is incomplete. This thesis proposes a model-guided design framework that integrates mechanistic …

Lyapunov-Based Economic Model Predictive Control For Detecting And Handling Actuator And Simultaneous Sensor/Actuator Cyberattacks On Process Control Systems, Henrique Oyama, Dominic Messina, Keshav Kasturi Rangan, Helen Durand

Chemical Engineering and Materials Science Faculty Research Publications

The controllers for a cyber-physical system may be impacted by sensor measurement cyberattacks, actuator signal cyberattacks, or both types of attacks. Prior work in our group has developed a theory for handling cyberattacks on process sensors. However, sensor and actuator cyberattacks have a different character from one another. Specifically, sensor measurement attacks prevent proper inputs from being applied to the process by manipulating the measurements that the controller receives, so that the control law plays a role in the impact of a given sensor measurement cyberattack on a process. In contrast, actuator signal attacks prevent proper inputs from being applied …

Lyapunov-Based Economic Model Predictive Control For Online Model Discrimination, Henrique Oyama, Helen Durand

Chemical Engineering and Materials Science Faculty Research Publications

Economic model predictive control (EMPC) is a flexible control design strategy that can be modified to achieve many operating goals while also ensuring safe operation (e.g., by adding Lyapunov-based stability constraints to form Lyapunov-based EMPC, or LEMPC). Prior works have investigated LEMPC capabilities for achieving goals online beyond optimizing process economics, including aiding in model structure selection to benefit model-based control system design since the accuracy and quality of the process model are important for achieving an expected performance from such systems. This work further probes the capabilities of LEMPC to accomplish multiple objectives during process operation, including aiding in …

In-Situ Generation Of Hydrocarbons From Kerogen Using Electromagnetic Radiation, Forrest Green

Graduate Theses & Non-Theses

From using surface seeps to modern day exploitation of hydrocarbon source rocks, the petroleum industry is awaiting the next big innovation, accelerated kerogen conversion. In the industry’s history, electromagnetic radiation (EMR) has been used for exploration and now it will be taken to the extreme by determining an effective and efficient method to synthetically generate readily available hydrocarbons. The study starts with examining and defining what kerogen is and its importance as a source material. A strong understanding of what kerogen is, and an analysis of other in-situ projects presents an opportunity to study the finer details of kerogen’s conversion …

Observing And Modeling Water Electrolysis Performance Limitations Attributed To Gas Generation And Porous Media Properties, Joseph S. Lopata

Theses and Dissertations

Water electrolysis has been a simple method of hydrogen production for over two centuries, but the exploration of its nuances is still accelerating. This work compiles numerous mechanisms via which electrolysis efficiency is influenced by phenomena that occur within, adjacent to, and nearby functional porous media. Computational and experimental methods are applied to electrolysis systems to quantify the impact of twophase flow patterns and porous media properties on energy losses, primarily those linked directly to the presence of the gas phase.

First, an introduction to the chemistry and operating principle of water electrolysis is presented and relevant works from the …

Application Of Red Cabbage Anthocyanins As Ph-Sensitive Pigments In Smart Food Packaging And Sensors, Reza Abedi-Firoozjah, Shima Yousefi, Mahshid Heydari, Faezeh Seyedfatehi, Shima Jafarzadeh, Reza Mohammadi, Milad Rouhi, Farhad Garavand

Research outputs 2022 to 2026

Anthocyanins are excellent antioxidant/antimicrobial agents as well as pH-sensitive indicators that provide new prospects to foster innovative smart packaging systems due to their ability to improve food shelf life and detect physicochemical and biological changes in packaged food. Compared with anthocyanins from other natural sources, red cabbage anthocyanins (RCAs) are of great interest in food packaging because they represent an acceptable color spectrum over a broad range of pH values. The current review addressed the recent advances in the application of RCAs in smart bio-based food packaging systems and sensors. This review was prepared based on the scientific reports found …

Visible Light Illuminated Tin Oxide-Gold Nanoparticle Schottky Junctions For H2o2 Generation In Water, Sarah Glass

Honors Capstones

No abstract provided.

Directed 3d Chemotaxis Of Cancer Cells In Response To Oscillating Chemical Gradients Using A Microfluidic Device, Trevor R. Thrasher

Honors Capstones

No abstract provided.

Rapid Removal Of Pfoa And Pfos Via Modified Industrial Solid Waste: Mechanisms And Influences Of Water Matrices, Hongyi Wan, Rollie Mills, Kai Qu, James C. Hower, M. Abdul Mottaleb, Dibakar Bhattacharyya, Zhi Xu

Chemical and Materials Engineering Faculty Publications

Emerging perfluoroalkyl and polyfluoroalkyl substances contaminate waters at trace concentrations, thus rapid and selective adsorbents are pivotal to mitigate the consequent energy-intensive and time-consuming issues in remediation. In this study, coal combustion residuals-fly ash was modified (FA-SCA) to overcome the universal trade-off between high adsorption capacity and fast kinetics. FA-SCA presented rapid adsorption (teq = 2 min) of PFOX (perfluorooctanoic acid and perfluorooctanesulfonic acid, collectively), where the dynamic adsorption capacity (qdyn = qm/teq) was 2–3 orders of magnitude higher than that of benchmark activated carbons and anion-exchange resins. Investigated by advanced characterization and kinetic models, the fast kinetics and superior …

Modelling And Validation Of A Gas-Solid Fluidized Bed Using Advanced Measurement Techniques, Sebastián Uribe, Haidar Taofeeq, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

With a Euler-two-phase (E2P) approach, through computational fluid dynamics (CFD) techniques, a mathematical model for the prediction of the local hydrodynamic behavior of a gas-solid fluidized bed was implemented. Simulations are conducted for a fluidized bed of 0.14 m internal diameter packed with Gerdart B glass beads particles, with an average diameter of 365 μm, at dimensionless inlet velocities ranging from (Formula presented.). The implemented model considers the multiphase and multiscale interactions through the inclusion of three sub-models, which allows the model to have a broad range of applicability. Predictions were compared against experimental measurements reported on previous contributions for …

Impact Of Polymer Rheology On Gel Treatment Performance Of Horizontal Wells With Severe Channeling, Jianqiao Leng, Mingzhen Wei, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Gel treatment has been a cost-effective method to control the conformance of a reservoir with severe heterogeneity problems. The water channels in such reservoirs can be classified as open fractures or high permeability porous media with pore-throat network. Many simulation studies have been conducted to discuss gel treatment performance for conformance control. However, nobody considered the polymer rheology difference in open fractures and porous media in simulation. Previous simulation studies also ignored the residual resistance factor as a function of rock permeability rather than a constant parameter. In this study, a conceptual simulation model was established to simulate the linear …

Integrated Direct Air Capture And Oxidative Dehydrogenation Of Propane With Co2 At Isothermal Conditions, Shane Lawson, Khaled Baamran, Kyle Newport, Turki Alghamadi, Gary Jacobs, Fateme Rezaei, Ali A. Rownaghi

Chemical and Biochemical Engineering Faculty Research & Creative Works

Developing routes of utilizing CO₂ emissions is important for long-term environmental preservation, as storing such emissions underground will eventually become unsustainable. One way of utilizing CO₂ emissions is as a light-oxidant feedstock for oxidative dehydrogenation of propane (ODHP) to propylene. However, the adsorption and reaction steps typically occur at widely different temperatures, meaning that the thermal gradients – and by extension process energy requirements – are often unreasonably high. In recent years, dual-functional materials (DFMs) – i.e., materials comprised of a high temperature adsorbent phase alongside a heterogeneous catalyst – have been employed for combined CO₂ adsorption …

Highly Active And Stable Low-Pgm And Pgm-Free Catalysts For Anion Exchange Membrane Fuel Cells, Horie Adabi Firouzjaie

Theses and Dissertations

Anion exchange membrane fuel cells (AEMFCs) have recently seen significant growth in interest as their achievable current density, peak power density, and longevity have been dramatically improved. Though these advances in performance have been important for demonstrating the feasibility of the technology, nearly all AEMFCs reported in the literature have required a relatively high loading of platinum group metal (PGM)- based catalysts at both the anode and cathode electrodes. However, to take command of the low-temperature fuel cell market, AEMFCs cannot simply reach the same performance as incumbent proton exchange membrane fuel cells (PEMFCs), which have had decades of development …

Fundamentals Of Adsorption And Large Scale Pressure Swing Adsorption (Psa) Process Design, Huan Jiang

Theses and Dissertations

This work focused on both fundamental of adsorption and large-scale PSA design. Chapter 1 and 2 addressed the analysis of conditions for formation of adsorption azeotropes in binary systems. Chapter 1 theoretically assessed the necessary and sufficient conditions for the formation of an adsorption azeotrope in a binary gas mixture when this mixture exhibits either intersecting or non-intersecting single gas isotherms. Chapter 2 confirmed theoretically whether adsorption azeotropes can form in a binary mixture at a pressure below the intersection pressure of the corresponding single gas isotherms. Analytical expressions derived for both general and dual thermodynamically consistent process Langmuir (DPL) …