Chemical Engineering Commons^™

Enzyme Actuated Bioresponsive Hydrogels, Andrew Wilson

All Theses

Bioresponsive hydrogels are emerging with technological significance in targeted drug delivery, biosensors and regenerative medicine. Conferred with the ability to respond to specific biologically derived stimuli, the design challenge is in effectively linking the conferred biospecificity with an engineered response tailored to the needs of a particular application. Moreover, the fundamental phenomena governing the response must support an appropriate dynamic range and limit of detection. The design of these systems is inherently complicated due to the high interdependency of the governing phenomena that guide the sensing, transduction, and the actuation response of hydrogels. To investigate the dynamics of these materials, …

Microstructural And Mechanical Characterization Of Soy-Based Polyethylene Fibers, Ozgun Ozdemir

All Theses

Bio-composite fibers have attracted increasing attention from environmentally-conscious consumers because of their low cost and biodegradability. Soy protein isolates and other purified forms have been proposed as bio-based substitutes for pure synthetic polymers for use in textiles. However, fibers from pure soy proteins do not possess adequate properties for use as textile fibers. Therefore, this research aimed to investigate composite fibers consisting of soy and polyethylene for their microstructure and mechanical properties. Changes in properties with increasing filler content and long-term properties of fibers were systematically examined.
First, the microstructure of the fibers was investigated by optical analysis. Six different …

Optimization Of A Dynamic Hot Water Pretreatment Of Switchgrass Using Catalysis By Carbonation To Maximize Carbochemical Yields, Rohit Tanaji Dhamdere

Graduate Theses and Dissertations

A bio-refinery is a facility that converts renewable bio-resources into value-added chemicals and products. In this context of a bio-refinery, the production of the carbochemicals such as HMF, furfural and organic acids illustrate that multiple products can be produced from a renewable source such as lignocellulosic biomass (switchgrass). Traditionally, carbochemicals such as furfural and HMF are produced using inorganic acids such as H2SO4, HCL, and H3PO4. The use of such acids requires the application of high cost materials of construction such as Hastelloy-C, titanium etc.

The objective of this study is to develop a semi-continuous process for the conversion of …

En Route Towards Α-Benzotriazoyl Nitroso Derivatives, Jean-Christophe M. Monbaliu, Lucas K. Beagle, Judit K. Beagle, Matthias Zeller, Christian V. Stevens, Alan R. Katritzky

Chemistry Faculty Publications

A new class of geminally-substituted nitroso compounds, i.e., α-benzotriazoyl nitroso derivatives, is presented. These compounds display a rather different behavior than other related nitroso compounds bearing a geminal electron-withdrawing group. An unexpected and spontaneous oxidation to the nitro analog is observed in solution.

Inkjet Printability Of Electronic Materials Important To The Manufacture Of Fully Printed Otfts, Sooman Lim

Dissertations

In this study, the inkjet printability of materials important to fabricating OTFTs was researched. In order to understand the jetting evolution of inkjet printed inks, simulations were performed with a nano copper and nano particle silver ink. To predict the inkjettability of the nano copper ink, Z and Oh numbers at different temperatures were determined. The results from the simulation studies were compared to experimental results obtained using a Dimatix inkjet printer. For the semiconductor ink, the inkjet printability of two organic semiconductors, P2TDC17FT4 (poly[(3,7-diheptadecylthieno[3,2-b]thieno[2',3':4,5]thieno[2,3-d]thiophene-2,6-diyl)[2,2'-bithiophene]-5,5'-diyl] dissolved in 1,2-dichlorobenzene and P3HT (poly-3 hexylthiophene) were compared to determine the relationship between drop …

Experimental Composite Guidance Conduits For Peripheral Nerve Repair: An Evaluation Of Ion Release, X. F. Zhang, A. Coughlan, H. O'Shea, Mark R. Towler, S. Kehoe, D. Boyd

Chemical and Biochemical Engineering Faculty Research & Creative Works

Poly (lactide-co-glycolide) (PLGA) - Pluronic F127 - glass composites have demonstrated excellent potential, from the perspective of controlled mechanical properties and cytocompatibility, for peripheral nerve regeneration. In addition to controlling the mechanical properties and cytotoxicity for such composite devices, the glass component may mediate specific responses upon implantation via degradation in the physiological environment and release of constituent elements. However, research focused on quantifying the release levels of such therapeutic ions from these experimental medical devices has been limited. To redress the balance, this paper explores the ion release profiles for Si⁴⁺, Ca²⁺, Na⁺, …

Gallium Containing Glass Polyalkenoate Anti-Cancerous Bone Cements: Glass Characterization And Physical Properties, A. W. Wren, A. Coughlan, L. Placek, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

A gallium (Ga) glass series (0.48SiO₂-0.40ZnO-0.12CaO, with 0.08 mol% substitution for ZnO) was developed to formulate a Ga-containing Glass Polyalkenoate Cement (GPC) series. Network connectivity (NC) and X-ray Photoelectron Spectroscopy (XPS) was employed to investigate the role of Ga³⁺ in the glass, where it is assumed to act as a network modifier. Ga-GPC series was formulated with E9 and E11 polyacrylic acid (PAA) at 50, 55 and 60 wt% additions. E11 working times (T_w) ranged from 68 to 96 s (Lcon.) and 106 s for the Ga-GPCs (LGa-1 and LGa-2). Setting times (T_s) …

Fabrication Of Printed Substrate For Surface Enhanced Raman Spectroscopy, Ali Eshkeiti

Masters Theses

A novel surface enhanced Raman spectroscopy (SERS) substrate was successfully fabricated on a silicon wafer using inkjet printing and on polyethylene terephthalate (PET) using gravure printing. Silver (Ag) nanoparticle (NP) based ink, was used for roughening of the surface of silicon and PET. A thickness of 400 nm was measured for the printed Ag NP printed film on silicon and the thickness of the single and double layered films on PET were measured as 340 nm and 680 nm, respectively by using vertical scanning interferometry. The Ag NP printed SERS substrate was tested for application with heavy metal compounds like …

The Influence Of Coating Structure On Sheet-Fed Offset Ink Setting Rates, Ting Chen

Masters Theses

Much attention has been paid to the study of quickset ink setting as a complex ink-coating interaction. Offset ink setting rates are typically measured as ink splitting forces versus time and the slope of the regression line obtained from a plot of these measured values is reported, but scant attention has been paid to the deviations from that straight line. An initial slow ink setting rate is desired to minimize back-trap mottle, carryover picking and piling and enhance ink gloss; then a faster ink setting rate during sheet delivery to the pile is desired to reduce the likelihood of ink …

Micro Hydroelectric Power Generation, Roberto Arraya Saenz

Chemical Engineering Undergraduate Honors Theses

MICRO-HYDRO ELECTRIC POWER GENERATION Roberto Arraya Department of Chemical Engineering – Honors Thesis ABSTRACT A major industrial water user in New Mexico discharges approximately 3.8 million gal of wastewater per day. The topology of the site provides an elevation difference of about 150 ft between the plant site and the entrance to the municipal sewage line; this flow and elevation difference is sufficient to produce about 40 kW of electrical power using a water turbine/electrical generator set to extract power from the flowing stream. This report includes designs and economic analyses for two distinct cases. One case is based on …

Design Of Advanced Fouling-Resistant And Self-Cleaning Membranes For Treatment Of Oily And Impaired Waters, Daniel Wandera

All Dissertations

The overall goal of my Doctor of Philosophy (PhD) research was to design and develop advanced anti-fouling and self-cleaning membranes for treating impaired waters. Initial work focused on the development of membranes to treat produced water, which is oily wastewater that is co-produced during oil and gas exploration. Economical, environmentally sustainable treatment of the large volumes of produced water is a grand challenge for oil and gas companies. While membranes offer many advantages over more conventional treatment methods, membrane-based treatment processes for oily waters often fail due to membrane fouling. Therefore, the primary objective of my doctoral research was to …

Adsorption Kinetics Of Pb(Ii) And Zn(Ii) Ions Unto Carbonized Groundnut Shells And Maize Cobs, Leke Luter, Aboi Julius, Henry T. Dekaa, B. A. Ikyenge, Ande Sesugh, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

Maize cobs and groundnut shell adsorbents from agricultural by-products were carbonized and investigated for adsorption of two selected metals, Lead (Pb II) and Zinc (Zn II) from aqueous solutions of these metals. Kinetic studies of the adsorption processes were investigated employing Elovich and the intraparticle diffussion models. The results showed that, the adsorption capacities of these comparatively cheaper adsorbents and their efficiency for the removal of Pb(II) and Zn(II) ions from aqueous solution present them suitable for use in place of the costly commercial activated carbons.

Characterization And Quantification Of Monomers, Oligomers, And By-Products From Xylan During Biomass Pretreatment, Ching-Shuan Lau

Graduate Theses and Dissertations

Biomass pretreatment generates inhibitory products, which reduce the overall yield of xylose for ethanol production. Understanding of hemicellulose depolymerization into xylose is essential to identify the pretreatment conditions that maximize xylose formation, but minimize the generation of these inhibitory products, such as formic acid and furfural. Thus, the goal of this project is to understand how dilute acid pretreatment parameters affect hemicellulose depolymerization, maximize xylose concentrations, and minimize by-products formation.

To progress towards this goal, rates and mechanisms of hemicellulose release must be determined. Birchwood xylan was used as the starting material to produce xylose oligomers. The hydrolyzed birchwood xylan …

Peptoid Based Slide Coatings For Disease Detection Via Elisa Microarray Analysis, Melissa Lea Hebert

Graduate Theses and Dissertations

Poly-N-substituted glycines (peptoids) are a very versatile family of synthetic molecules that can be customized for any number of applications. In this study, we chose to use peptoids as a foundation for sandwich ELISA microarray analysis with a long term goal of creating an early detection device for complex diseases such as cancer. The peptoids were designed to self-assemble into microspheres to be used in coatings on the surface of the microarray substrates to increase the surface area available for antibody attachment. This increased antibody density would lead to an increase in the microarray analysis sensitivity and dynamic range. Studies …

Plasmonic Pervaporation Via Gold Nanoparticle-Functionalized Nanocomposite Membranes, Aaron Russell

Graduate Theses and Dissertations

Butanol derived from biological feedstocks has significant potential as a liquid fuel source, but the separation methods used in its production can be prohibitively expensive and are therefore currently the subject of extensive research. Pervaporation is a promising membrane process that is effective in butanol separations, but involves a large energy demand. This study examines the possibility of increasing flux and energy efficiency in pervaporation via plasmonic heating of gold nanoparticle-functionalized, polymer nanocomposite membranes (AuNCMs) in lieu of conventional feed heating. An economic analysis demonstrated that plasmonic pervaporation could achieve significant reductions in energy usage and utility cost in butanol …

Determining The Operation Limits Of Two Distillation Columns, Murat Ozkaya

Masters Theses and Doctoral Dissertations

The two distillation columns of Wacker Institute pilot plant at the Chattanooga State Community College are investigated for stable operating regions, flooding phenomena that occurs in the bubble-cap tray distillation column, weeping phenomena that occurs in the sieve tray distillation column, and comparison of operation between the two distillation columns. With the use of a distributed control system (DCS) and glass equipment in the pilot plant, these phenomena are analyzed visually and with the help of instrumentation readings. The energy usage and production limits of both distillation columns are discussed. The flooding of bubble-cap trays occur before reaching production goals …

Processes For The Production Of Buprenorphine With Reduced Impurity Formation, Brenda E. Allen, Esa T. Jarvi, Dennis J. Kaluta, James R. Meyer, Keith Tomazi, Anthony Mannino, Brian Orr

Chemical and Biochemical Engineering Faculty Research & Creative Works

The present invention provides process for the production of opiate alkaloids. In particular, the present invention provides processes for the production of buprenorphine or a derivative of buprenorphine that minimizes the formation of impurities.

Solid Oxide Fuel Cells With Both High Voltage And Power Output By Utilizing Beneficial Interfacial Reaction, Chao Su, Zongping Shao, Ye Lin, Yuzhou Wu, Huanting Wang

Faculty Publications

An intriguing cell concept by applying proton-conducting oxide as the ionic conducting phase in the anode and taking advantage of beneficial interfacial reaction between anode and electrolyte is proposed to successfully achieve both high open circuit voltage (OCV) and power output for SOFCs with thin-film samarium doped ceria (SDC) electrolyte at temperatures higher than 600 °C. The fuel cells were fabricated by conventional route without introducing an additional processing step. A very thin and dense interfacial layer (2–3 μm) with compositional gradient was created by in situ reaction between anode and electrolyte although the anode substrate had high surface roughness …

Homogeneous Viologens For Use As Catalysts In Direct Carbohydrate Fuel Cells, Dane C. Hansen

Theses and Dissertations

Deriving electrical energy from glucose and other carbohydrates under mild conditions is an important research objective because these biomolecules are abundant, renewable, and can provide 12 to 24 electrons per molecule, yielding substantial electrical power. It was previously observed that disubstituted viologens, salts of N,N'-disubstituted 4,4'-bipyridine, are able to oxidize glucose under alkaline conditions. Building on that initial result, the objective of this work was to understand and quantify the effectiveness and utility of viologens as catalysts for use in direct carbohydrate fuel cells.The extent that viologens oxidize carbohydrates, the conditions under which that oxidation occurs, and the mechanism for …

Order-Disorder Transition Of Aragonite Nanoparticles In Nacre, Zaiwang Huang, Xiaodong Li

Faculty Publications

Understanding nacre’s bottom-up biomineralization mechanism, particularly, how individual aragonite platelets are formed, has long remained elusive due to its crystallographic peculiarity and structural complexity. Here we report that crystallographic order-disorder transition can be triggered within individual aragonite platelets in pristine nacre by means of heat treatment and/or inelastic deformation, offering a unique opportunity to discriminate mysterious aragonite nanoparticles in transmission electron microscopy. Our findings unambiguously uncover why aragonite nanoparticles in pristine nacre have long been inaccessible under TEM observation, which is attributed to the monocrystal-polycrystal duality of the aragonite platelet. The underlying physical mechanism for why an individual aragonite platelet …

Transparent Conducting Films Of Cdse(Zns) Core(Shell) Quantum Dot Xerogels, Lasantha Korala, Li Li, Stephanie L. Brock

Chemistry Faculty Research Publications

A method of fabricating sol–gel quantum dot (QD) films is demonstrated, and their optical, structural and electrical properties are evaluated. The CdSe(ZnS) xerogel films remain quantum confined, yet are highly conductive (10⁻³ S cm⁻¹). This approach provides a pathway for the exploitation of QD gels in optoelectronic applications.

Constrained Control And Optimization Of Tubular Solid Oxide Fuel Cells For Extending Cell Lifetime, Ben Spivey, John Hedengren, Thomas F. Edgar

Faculty Publications

Extending fuel cell lifetime is a necessary objective for reducing fuel cell power generation cost of electricity. Capital costs comprise the most significant fraction of the cost of electricity. Reducing the frequency of fuel cell replacement can be achieved by implementing a control strategy that prevents excursions into operating regions causing failure. In this paper we implement a constrained MIMO model predictive controller (MPC) to avoid the failure modes relevant for a high-temperature tubular solid oxide fuel cell (SOFC) system while performing load-following. The primary causes of failure are catalyst poisoning, fuel or air starvation, carbon deposition, and microcracking. Prior …

An Oxidase-Based Electrochemical Fluidic Sensor With High-Sensitivity And Low-Interference By On-Chip Oxygen Manipulation, Nitin Radhakrishnan, Jongwon Park, Chang Soo Kim

Electrical and Computer Engineering Faculty Research & Creative Works

Utilizing a simple fluidic structure, we demonstrate the improved performance of oxidase-Based enzymatic biosensors. Electrolysis of water is utilized to generate bubbles to manipulate the oxygen microenvironment close to the biosensor in a fluidic channel. for the proper enzyme reactions to occur, a simple mechanical procedure of manipulating bubbles was developed to maximize the oxygen level while minimizing the pH change after electrolysis. the sensors show improved sensitivities based on the oxygen dependency of enzyme reaction. in addition, this oxygen-rich operation minimizes the ratio of electrochemical interference signal by ascorbic acid during sensor operation (i.e., amperometric detection of hydrogen peroxide). …

Computational Modeling Of Functionalized Carbon Nanotubes, Nathaniel Lee Miller

Theses and Dissertations

Ab initio self-consistent field (SCF) molecular orbital calculations were performed employing various basis sets to computationally predict methods to functionalize and solubilize carbon nanotubes. The structure and Restricted Hartree-Fock (RHF) or “total” energies of functionalized nanotubes of various configurations were determined via theoretical calculations. Total energies were used to determine preferences for adsorption on nanotube sur-faces. Various diameter carbon nanotubes (CNTs) were tested to determine where a transition from a non-wrapping to a wrapping approach was found likely to occur as a function of diameter. Further refinements to this method could be used to explore additional interactions as nanotube diameter …

Examination Of The Migratory Potential Of Patterned Cortical Neurons Using Laser Direct-Write, T. B. Phamduy, C. J. Rivet, D. Kingsley, R. J. Gilbert, D. B. Chrisey

Chemical and Biochemical Engineering Faculty Research & Creative Works

We describe the patterning of neuronal cultures by a laser-based printing system. Embryonic chick cortical neurons were transferred into predetermined array positions with micron accuracy, enabling detailed study of neuronal migration, aggregation, and neurite outgrowth regulated by cell-cell interactions on a homogeneous surface. Images of cells were analyzed up to 14 days. Results demonstrated that increasing the spacing between neighboring groups of cells causes intra-group cells to preferentially migrate towards each other and aggregate towards the center of the printed 'spot'. In addition, increasing the printed 'spot' size encouraged migration towards neighboring groups of cells. © 2012 IEEE.

The Structural Characterization Of Ga 2o 3-Na 2o-Cao-Zno-Sio 2 Bioactive Glasses, T. J. Keenan, A. W. Wren, A. Coughlan, M. M. Hall, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

The characterization of bioactive glasses in which zinc (Zn) has been incrementally replaced by gallium (Ga). © 2012 IEEE.

Silver Coated Bioactive Glass Particles For Wound Healing Applications, P. Hassanzadeh, A. W. Wren, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

Hench and colleagues discovered that bone could bond chemically to certain glass compositions in 1969 [1]. This group of glasses is known as bioactive glasses [1]. Some special compositions of bioactive glasses will bond to soft tissues as well as bone [1]. One of the important characteristics of bioactive glasses is their ability to release beneficial ions such as Ca²⁺, Na⁺, Zn²⁺, Sr²⁺, and PO 43- in the body, which promote self-healing [2]. Bioactive glasses generally contain much less glass former (e.g., SiO₂, B₂O₃ etc.) than conventional …

Increasing The Quantity Of Silver In Zinc-Based Glass Polyalkenoate Cement: Is There An Improvement In Antibacterial Efficacy?, A. Coughlan, S. M. Breed, C. Ashraf, J. A. Cardinale, M. M. Hall, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

Bone cements should have the ability to chemically bond to both bone and surgical metals, exhibit no chemical or thermal necrosis, and have no significant shrinkage or exotherm upon setting. Taking these properties into consideration, glass polyalkenoate cements (GPCs) have potential as bone cements. GPCs are formed by the reaction between an ion-leachable glass and an aqueous solution of polyacrylic acid (PAA) [1] and have proven antibacterial and cariostatic properties [2], which are related to their ability to release beneficial amounts of ions over time [3, 4]. The GPCs can be formulated to release ions that can have a therapeutic …

Gallium Containing Glass Polyalkenoate Bone Cements: Glass Characterization And Physical Properties, L. Placek, A. W. Wren, A. Coughlan, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

Gallium (Ga) glasses were developed to formulate a Glass Polyalkenoate Cement (GPC) series with both E9 and E11 polyacrylic acid (PAA) at 50, 55 and 60wt% additions. Working times (T w), setting times (T s), compression (σ c), and biaxial flexural (σ f) strength testing were evaluated to determine the GPCs potential use in orthopedics. © 2012 IEEE.

An Overview Of Electrode Materials In Microbial Fuel Cells, Su-Qin Ci, Na Wu, Zhen-Hai Wen, Jing-Hong Li

Journal of Electrochemistry

Microbial fuel cells (MFCs) are devices that can directly convert organic chemical energy into electrical energy with microbial as catalysts. MFCs are a promising bio-electrochemical system with the potential to degrade organic sewage and produce electricity. This article supplies a critical and comprehensive review for the electrode materials concerning about anode and cathode in MFCs, including the fabrications, functional modifications and surface constructions of electrode materials, as well as their applications in MFCs. Additionally, the existing problems of electrode materials in current MFCs have been demonstrated in order to provide the guideline for exploring the next-generation electrode materials for MFCs.