Open Access. Powered by Scholars. Published by Universities.®

Chemical Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

2005

Discipline
Institution
Keyword
Publication
Publication Type
File Type

Articles 151 - 180 of 188

Full-Text Articles in Chemical Engineering

Zeolite And Metal Oxide Catalysts For The Production Of Dimethyl Sulfide And Methanethiol, Craig Plaisance Jan 2005

Zeolite And Metal Oxide Catalysts For The Production Of Dimethyl Sulfide And Methanethiol, Craig Plaisance

LSU Master's Theses

Metal oxide and zeolite catalysts were examined to determine their suitability for the production of methanethiol and dimethyl sulfide from the condensation of methanol and hydrogen sulfide. Fixed bed reactor experiments were used to test the catalysts in these processes. The acid sites of these catalysts were characterized by investigating the thermal desorption of 1-propanamine from these sites. It was found that WO3/ZrO2, La2O3/Al2O3, g-Al2O3, and HZSM-5 catalysts were active and selective in the production of dimethyl sulfide. On these four catalysts, the reaction converting methanol to dimethyl ether and the methanethiol disproportionation reaction were fast and close to equilibrium. …

Go to article

Use Of Orthogonal Arrays, Quasi-Monte Carlo Sampling And Kriging Response Models For Reservoir Simulation With Many Varying Factors, Subhash Kalla Jan 2005

Use Of Orthogonal Arrays, Quasi-Monte Carlo Sampling And Kriging Response Models For Reservoir Simulation With Many Varying Factors, Subhash Kalla

LSU Master's Theses

Asset development teams may adjust simulation model parameters using experimental design to reveal which factors have the greatest impact on the reservoir performance. Response surfaces and experimental design make sensitivity analysis less expensive and more accurate, helping to optimize recovery under geological and economical uncertainties. In this thesis, experimental designs including orthogonal arrays, factorial designs, Latin hypercubes and Hammersley sequences are compared and analyzed. These methods are demonstrated for a gas well with water coning problem to illustrate the efficiency of orthogonal arrays. Eleven geologic factors are varied while optimizing three engineering factors (total of fourteen factors). The objective is …

Go to article

Mathematical Models For Estimating Volatile Chemical Emissions From Dredging Operations, Kenneth Alexander Fountain Jan 2005

Mathematical Models For Estimating Volatile Chemical Emissions From Dredging Operations, Kenneth Alexander Fountain

LSU Master's Theses

Dredging operations have been a common remediation for contaminated sediment in an effort to reduce the harmful impact on the environment. The objective of this research was to create models used for estimating chemical release to air from remediating the Indiana Harbor and Canal (IHC) as three separate dredging operations; the Dredge Site, Exposed DM CDF, and Ponded CDF. The evaporative flux estimations are based on a two-resistance mass transport path inclusive of both the molecular diffusion in porous media and interfacial airside mass transport resistances. Several chemodynamic algorithms were used in calculating key transport parameters. Laboratory tests were performed …

Go to article

Electrodeposition Of Magnetic Nanowires And Nanotubes, Despina Mehedintu Davis Jan 2005

Electrodeposition Of Magnetic Nanowires And Nanotubes, Despina Mehedintu Davis

LSU Master's Theses

The current perpendicular to the plane giant magneto-resistance (CPP)-(GMR) effect makes multilayered nanowires of huge interest as magnetic sensor materials. GMR showing multilayer nanostructures are composed of alternating ferromagnetic and nonmagnetic nanometric layers. The giant magnetoresistance (GMR) property is described as a change in electrical resistance when an external magnetic field is introduced. Electrodeposition is the most efficient method for fabricating magnetic nanowires. In addition to the cost-effectiveness, electrodeposition is one of the few methods that can overcome the geometrical restrictions of inserting metals into very deep nanometric recesses, making it the favored method for nanowire and nanotube fabrication. In …

Go to article

Analysis Of Alternative Well Control Methods For Dual Density Deepwater Drilling, Mikolaj Stanislawek Jan 2005

Analysis Of Alternative Well Control Methods For Dual Density Deepwater Drilling, Mikolaj Stanislawek

LSU Master's Theses

The recent push into deepwater is currently limited by high drilling costs resulting from conventional well designs. As a result, dual gradient drilling methods have been proposed. This research investigates riser gas-lift as a potential means to implement a dual gradient system. A primary concern is well control in a system containing so many different density fluids and different flow paths. The specific concerns addressed in this study were kick detection, cessation of formation feed-in, removal of kick fluids, and re-establishing hydrostatic control with a constant bottom hole pressure method. These concerns were studied using a transient, multiphase simulator whose …

Go to article

Experimental Investigation Of Dynamic Interfacial Interactions At Reservoir Conditions, Wei Xu Jan 2005

Experimental Investigation Of Dynamic Interfacial Interactions At Reservoir Conditions, Wei Xu

LSU Master's Theses

Much of the research on wettability in the existing literature has been done using stocktank oils and at ambient conditions. The main objective of this study is therefore to examine the validity of ambient measurements in inferring in-situ reservoir wettability. For this purpose, Drop-Shape-Analysis for interfacial tension and Dual-Drop-Dual-Crystal (DDDC) contact angle measurements have been carried out using dolomite rock, Yates reservoir stocktank and live crude oils and Yates synthetic brine at Yates reservoir conditions of 82oF and 700 psi. Two types of surfactants (nonionic and anionic) in varying concentrations have been used to study the effect of surfactants on …

Go to article

Enhanced Gas Recovery Using Pressure And Displacement Management, Thomas Walker Jan 2005

Enhanced Gas Recovery Using Pressure And Displacement Management, Thomas Walker

LSU Master's Theses

The work contained in this thesis combines two previous enhanced gas recovery techniques; coproduction of water and gas from water-drive reservoirs and waterflooding of low pressure gas reservoirs. These two techniques allow the control of reservoir pressure and sweep efficiency through planed production or injection of water. A recovery optimization method, which is applicable to any gas reservoir, was developed using the concept of pressure and displacement management (PDM). Two simulation studies were conducted, using Eclipse©, to investigate recovery optimization by coproduction and waterflooding. From the coproduction study it was determined that the water production rate needed to optimize recovery …

Go to article

Modeling The Flow Of Non-Newtonian Fluids In Packed Beds At The Pore Scale, Matthew Balhoff Jan 2005

Modeling The Flow Of Non-Newtonian Fluids In Packed Beds At The Pore Scale, Matthew Balhoff

LSU Doctoral Dissertations

Flow and transport in porous media are important in many science and engineering applications such as composite materials, subsurface water contamination, packed-bed reactors, and enhanced oil recovery. The general approach to modeling such processes is at the continuum scale. Semi-empirical expressions, such as Darcy's law, are substituted for velocity in the continuity equation, which is then coupled with a momentum, mass, and energy balance. While a continuum approach is acceptable in some cases, additional modeling is required for certain non-linear flows, such as multi-phase flows, inertial flows, non-Newtonian flows, and reactive flows. Pore-scale modeling is a first-principles approach to modeling …

Go to article

Optimal Operating Strategy For Wells With Downhole Water Sink Completions To Control Water Production And Improve Performance, Ozan Arslan Jan 2005

Optimal Operating Strategy For Wells With Downhole Water Sink Completions To Control Water Production And Improve Performance, Ozan Arslan

LSU Doctoral Dissertations

Downhole water sink (DWS) technology is an alternative to conventional limited-entry completions to control water production in wells with bottom water drive. DWS wells comprise two completions: the bottom completion produces water and keeps the top completion open to oil inflow. The system performance depends on careful manipulation of the top and bottom rates to maximize oil productivity and produce oil-free water from the bottom completion. Conventional nodal analysis cannot provide a solution for DWS wells because the critical rates for water coning change with water drainage rate. A reservoir simulator is used to model two-phase flow to the dual …

Go to article

Physico-Chemical Characteristics Of European Pulverized Coal Combustion Fly Ashes, N. Moreno, X. Querol, J. M. Andrés, K. Stanton, Mark R. Towler, H. Nugteren, M. Janssen-Jurkovicová, R. Jones Jan 2005

Physico-Chemical Characteristics Of European Pulverized Coal Combustion Fly Ashes, N. Moreno, X. Querol, J. M. Andrés, K. Stanton, Mark R. Towler, H. Nugteren, M. Janssen-Jurkovicová, R. Jones

Chemical and Biochemical Engineering Faculty Research & Creative Works

Fly ashes sourced from European pulverized coal burning power plants (from Spain, The Netherlands, Italy and Greece) were characterized in terms of their chemical composition, mineralogy and physical properties. The amount and composition of the glass present in the ashes were also determined. The materials analyzed have very different compositions and were selected with a view to determining their suitability for different applications and for further studies on applications. The results were compared to the literature to determine their similarities to UK coal fly ashes. Chemical analysis has enabled the categorization of the ashes based on their oxide contents. Devitrification …

Go to article

Flow Distribution Characteristics Of A Gas-Liquid Monolith Reactor Using Computed Tomography, Shaibal Roy, Muthanna H. Al-Dahhan Jan 2005

Flow Distribution Characteristics Of A Gas-Liquid Monolith Reactor Using Computed Tomography, Shaibal Roy, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

Flow Distribution Characteristics Were Investigated and Quantified in a 0.05 M Diameter Monolith Reactor, Operated Co-Current Downward in the Taylor Flow Regime, using Gamma Ray Computed Tomography (CT). the Flow Conditions Were Selected to Operate the Reactor in the Taylor Flow Regime and to Bracket Some Commercially Viable Operating Conditions for Such Reactors. Various Operating Parameters Were Evaluated for their Effect on the Degree of Flow Non-Uniformity in the Monolith Crosssection. the Results Show that within the Range of Gas and Liquid Superficial Velocities Investigated, There Exists a Window of Operating Conditions (Intermediate Gas and Liquid Velocities) Which Corresponds to …

Go to article

Phase Distribution In A High Pressure Slurry Bubble Column Via A Single Source Computed Tomography, Novica Rados, Ashfaq Shaikh, Muthanna H. Al-Dahhan Jan 2005

Phase Distribution In A High Pressure Slurry Bubble Column Via A Single Source Computed Tomography, Novica Rados, Ashfaq Shaikh, Muthanna H. Al-Dahhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

Due to their Numerous Advantages, Slurry Bubble Column Reactors (SBCR) Are Gaining Wide Importance in the Petroleum, Petrochemical, Chemical, and Biochemical Industries. Most Previous Literature Studies on the Fluid Dynamics and the Phase Holdup Distribution in SBCR Are Limited to Low Superficial Gas Velocity, Low Solids Loading, and the Atmospheric Pressure. Moreover, the Presence of a Solids Phase Poses Difficulties in Probe Measurement Techniques Such as Pitot Tube and Optical Probe and See through Measurement Techniques Such as Particle Image Velocimetry (PIV), Laser Doppler Velocimetry (LDV). Single Source Γ-Ray Computed Tomography (CT) Has Been Used to Measure Cross-Sectional Phase Holdup …

Go to article

Experimental Investigation Of Drilling Fluid Formulations And Processing Methods For A Riser Dilution Approach To Dual Density Drilling, John Shelton Jan 2005

Experimental Investigation Of Drilling Fluid Formulations And Processing Methods For A Riser Dilution Approach To Dual Density Drilling, John Shelton

LSU Master's Theses

Oil and natural gas resources in the deepwater Gulf of Mexico are important for the U.S. economy, but development is limited by high costs. Dual density drilling concepts that result in wellbore pressure gradients similar to the natural subsurface gradients can simplify well designs and reduce costs. Riser dilution may be an economical means of achieving such a system. This system would use a low density fluid to dilute the weighted wellbore fluid and give an intermediate density fluid in the riser. Two key concerns addressed in this study are whether a drilling fluid can be formulated that will suspend …

Go to article

Tunable Multiferroic Properties In Nanocomposite Pbtio3-Cofe2O4 Epitaxial Thin Films, M. Murakami, K.-S. Chang, M. A. Aronova, C.-L. Lin, Ming H. Yu, Jason R. Hattrick-Simpers, M. Wuttig, I. Takeuchi, C. Gao, B. Hu, S. E. Lofland, L. A. Knauss, L. A. Bendersky Jan 2005

Tunable Multiferroic Properties In Nanocomposite Pbtio3-Cofe2O4 Epitaxial Thin Films, M. Murakami, K.-S. Chang, M. A. Aronova, C.-L. Lin, Ming H. Yu, Jason R. Hattrick-Simpers, M. Wuttig, I. Takeuchi, C. Gao, B. Hu, S. E. Lofland, L. A. Knauss, L. A. Bendersky

Faculty Publications

We report on the synthesis of PbTiO3–CoFe2O4 multiferroic nanocomposites and continuous tuning of their ferroelectric and magnetic properties as a function of the average composition on thin-film composition spreads. The highest dielectric constant and nonlinear dielectric signal was observed at (PbTiO3)85–(CoFe2O4)15, where robust magnetism was also observed. Transmission electron microscopy revealed a pancake-shaped epitaxial nanostructure of PbTiO3 on the order of 30 nm embedded in the matrix of CoFe2O4 at this composition. Composition dependent ferroics properties observed here indicate that there …

Go to article

Effects Of Dynamic Fluid Pressure On Chondrocytes Cultured In Biodegradable Poly(Glycolic Acid) Fibrous Scaffolds, Lichun Lu, Xun Zhu, Larry G. Pederson, Esmaiel Jabbari, Bradford Currier, Shawn O'Driscoll, Michael Yaszemski Jan 2005

Effects Of Dynamic Fluid Pressure On Chondrocytes Cultured In Biodegradable Poly(Glycolic Acid) Fibrous Scaffolds, Lichun Lu, Xun Zhu, Larry G. Pederson, Esmaiel Jabbari, Bradford Currier, Shawn O'Driscoll, Michael Yaszemski

Faculty Publications

No abstract provided.

Go to article

Transient Analysis Of A Porous Electrode, Sheba Devan, Venkat R. Subramanian, Ralph E. White Jan 2005

Transient Analysis Of A Porous Electrode, Sheba Devan, Venkat R. Subramanian, Ralph E. White

Faculty Publications

An analytical expression is presented for the voltage response including the transient voltage for a simple (i.e., no concentration gradients) porous electrode model subject to a sinusoidal input current density. The transient voltage response as a function of the frequency, exchange current density, and double layer capacitance is studied independent of the periodic (steady state) voltage response. The change in the voltage response in the transient region is compared to that of the periodic voltage response with respect to the parameters. The physical properties of the porous electrode can be estimated using the voltage response in the transient …

Go to article

Cubic Spline Regression For The Open-Circuit Potential Curves Of A Lithium-Ion Battery, Qingzhi Guo, Ralph E. White Jan 2005

Cubic Spline Regression For The Open-Circuit Potential Curves Of A Lithium-Ion Battery, Qingzhi Guo, Ralph E. White

Faculty Publications

A cubic spline regression model was used to fit the experimental open-circuit potential (OCP) curves of two intercalation electrodes of a lithium-ion battery. All the details of an OCP curve were accurately predicted by the resulting model. The number of regression intervals used to fit an OCP curve was determined in a way such that in each regression interval the OCP exhibits a profile predictable by a third-order polynomial. The locations of the data points used to separate regression intervals were optimized. Compared to a polynomial model with the same number of fitting parameters, the cubic spline regression model is …

Go to article

A Mathematical Model For A Lithium-Ion Battery/Electrochemical Capacitor Hybrid System, Godfrey Sikha, Ralph E. White, Branko N. Popov Jan 2005

A Mathematical Model For A Lithium-Ion Battery/Electrochemical Capacitor Hybrid System, Godfrey Sikha, Ralph E. White, Branko N. Popov

Faculty Publications

A one-dimensional model for predicting the performance of a battery/electrochemical capacitor-hybrid system has been developed. Simulation results are presented for a LiCoO2|LiPF6 ethylene carbonate/dimethyl carbonate|carbon battery system and a Maxwell PC 10F carbon double-layer electrochemical capacitor. The current shared between the battery and the electrochemical capacitor at very short times depends on the ohmic resistances of the battery and the capacitor. As the discharge proceeds, the operating conditions such as frequency, duty ratio, and peak pulse discharge current control the current shared among parallel circuits. These parameters also determine the extent of the run time increase of …

Go to article

Fabrication Of Core-Shell Nanoparticles, Zhanhu Guo Jan 2005

Fabrication Of Core-Shell Nanoparticles, Zhanhu Guo

LSU Doctoral Dissertations

Metallic Cu and Au shells were fabricated around cobalt nanoparticles. A new technique to coat nanoparticles with carbon coatings and poly(methyl methacrylate) (PMMA) was developed. The copper shell formation is a self-limiting process. A thin copper shell (0.82 nm) around the cobalt nanoparticle (1.56 nm) enhanced the magnetic property by increasing the blocking temperature from 124 K to 235 K for nanoparticles with a copper shell. The formed gold shell (0.67 nm) enhanced the cobalt nanoparticle magnetic property by increasing the blocking temperature above room temperature. The magnetic moment in the Co-Cu and Co-Au core-shell nanoparticle is much higher than …

Go to article

Shaly Sand Interpretation Using Cec-Dependent Petrophysical Parameters, Fnu Kurniawan Jan 2005

Shaly Sand Interpretation Using Cec-Dependent Petrophysical Parameters, Fnu Kurniawan

LSU Doctoral Dissertations

This research explores the characterization of petrophysical parameters such as cementation exponent, saturation exponent and effective porosity as a function of cations exchange capacity (CEC), and its impact on shaly sand interpretation. Experimental and field data were used in the study. The latest LSU model for shaly sand interpretation uses of two cementation exponents, mf and mc, to represent the tortuosity of electric current path in free water and clay bound water, respectively. Experimental measurements on three types of rock, clean sand, shaly sand and pure shale using different brine salinity, were conducted to validate the use of these two …

Go to article

Geostatistical Integration Of Geophysical, Well Bore And Outcrop Data For Flow Modeling Of A Deltaic Reservoir Analogue, Hong Tang Jan 2005

Geostatistical Integration Of Geophysical, Well Bore And Outcrop Data For Flow Modeling Of A Deltaic Reservoir Analogue, Hong Tang

LSU Doctoral Dissertations

Significant world oil and gas reserves occur in deltaic reservoirs. Characterization of deltaic reservoirs requires understanding sedimentary and diagenetic heterogeneity at the submeter scale in three dimensions. However, deltaic facies architecture is complex and poorly understood. Moreover, precipitation of extensive calcite cement during diagenesis can modify the depositional permeability of sandstone reservoir and affect fluid flow. Heterogeneity contributes to trapping a significant portion of mobile oil in deltaic reservoirs analogous of Cretaceous Frontier Formation, Powder River Basin, Wyoming. This dissertation focuses on 3D characterization of an ancient deltaic lobe. The Turonian Wall Creek Member in central Wyoming has been selected …

Go to article

Long Term Pressure Behavior In Turbidite Reservoirs, Feng Wang Jan 2005

Long Term Pressure Behavior In Turbidite Reservoirs, Feng Wang

LSU Doctoral Dissertations

In this study, we investigated several possible mechanisms that would give rise to the anomalous pressure behavior (early concave-up on Horner plot or upward drift on the derivative curve of the log-log plot and asymmetry between the pressure drawdown and buildup behavior) sometimes encountered in the turbidite reservoirs in GOM primarily using numerical simulation and 2-level experimental designs. We ascertained the most influential parameters to the pressure behavior and identified that multilayer commingled system and the leaky compartment model are the most probable mechanisms to cause the anomalous behavior due to layer or zone property contrast to a certain degree. …

Go to article

Photocatalysis In A Novel Semiconducting Optical Fiber Monolithic Reactor For Wastewater Treatment, Hongfei Lin Jan 2005

Photocatalysis In A Novel Semiconducting Optical Fiber Monolithic Reactor For Wastewater Treatment, Hongfei Lin

LSU Doctoral Dissertations

The development of photocatalytic reactors is essential for the successful exploitation of heterogeneous photocatalysis on semiconductor particles, which has been shown to be an effective means of removing organic pollutants from wastewater streams. In this dissertation, a novel photocatalytic optical fiber monolith reactor (OFMR), which employed a ceramic multi-channel monolith as a support for TiO2 and quartz fibers inserted inside the monolithic channels as both a light-transmitting conductor and a support for TiO2, was developed for wastewater treatment by investigating the photocatalytic degradation of o-dichlorobenzene (DCB) and phenanthrene (PHE). This configuration provides a high surface area for catalyst coating per …

Go to article

Chemical Vapor Deposition Of Thin Films For Ulsi Interconnect Metallization, Lidong Wang Jan 2005

Chemical Vapor Deposition Of Thin Films For Ulsi Interconnect Metallization, Lidong Wang

LSU Doctoral Dissertations

We have studied the kinetics of copper chemical vapor deposition (CVD) for interconnect metallization using solution delivery of Cu(hfac)2 (Cu(II) hexafluoroacetyl-acetonate) dissolved in isopropanol. We observe a growth rate of 17.7 „b 1.5 nm/min at reference conditions of 300„aC substrate temperature, 0.025 Torr Cu(hfac)2 partial pressure, 1.6 Torr isopropanol (reducing agent), and 80 Torr H2 (carrier gas). The film resistivity approaches the bulk value of copper for film thickness greater than 100 nm. Reaction order experiments show first-order kinetics with respect to Cu(hfac)2 partial pressure and zero-order with respect to isopropanol. A series reaction mechanism including three kinetically significant steps …

Go to article

Stability, Transport And Applications Of Polyaphrons In Porous Media, Le Yan Jan 2005

Stability, Transport And Applications Of Polyaphrons In Porous Media, Le Yan

LSU Doctoral Dissertations

Polyaphrons are a kind of macroemulsion. The most distinctive feature of polyaphrons is their high stability. On the other hand, certain polyaphrons can be effectively destabilized by multivalent ions. In this dissertation, we devise a novel procedure that utilizes the fact that polyaphrons can be destabilized by certain ions to deliver light chemicals to lower the density of dense non-aqueous phase liquid (DNAPL) contaminants in situ. We first investigate how the stability of diluted polyaphrons is affected by the properties of the continuous phase. We find that polyaphrons can be destabilized by a low concentration of Al3+ or Ca2+ in …

Go to article

Multiphase Mechanisms And Fluid Dynamics In Gas Injection Enhanced Oil Recovery Processes, Madhav M. Kulkarni Jan 2005

Multiphase Mechanisms And Fluid Dynamics In Gas Injection Enhanced Oil Recovery Processes, Madhav M. Kulkarni

LSU Doctoral Dissertations

Currently, the Water-Alternating-Gas (WAG) process is the most widely practiced horizontal mode gas injection process in the industry. Although this process is conceptually sound, it has resulted in low (5 – 10%) oil field recoveries. Conversely, the gravity stable mode of gas injection has carved its niche as one of the most effective methods of gas injection EOR in the dipping reservoirs and pinnacle reefs. The Gas Assisted Gravity Drainage (GAGD) process is therefore being developed at LSU to extend these highly successful gravity stable applications to horizontal type reservoirs. The dissertation attempts to address six key questions: (i) do …

Go to article

Measurement And Modeling Of Fluid-Fluid Miscibility In Multicomponent Hydrocarbon Systems, Subhash C. Ayirala Jan 2005

Measurement And Modeling Of Fluid-Fluid Miscibility In Multicomponent Hydrocarbon Systems, Subhash C. Ayirala

LSU Doctoral Dissertations

Carbon dioxide injection has currently become a major gas injection process for improved oil recovery. Laboratory evaluations of gas-oil miscibility conditions play an important role in process design and economic success of field miscible gas injection projects. Hence, this study involves the measurement and modeling of fluid-fluid miscibility in multicomponent hydrocarbon systems. A promising new vanishing interfacial tension (VIT) experimental technique has been further explored to determine fluid-fluid miscibility. Interfacial tension measurements have been carried out in three different fluid systems of known phase behavior characteristics using pendent drop shape analysis and capillary rise techniques. The quantities of fluids in …

Go to article

Indium Growth On Si(100)-2 X 1 By Femtosecond Pulsed Laser Deposition, M. A. Hafez, M. S. Hegazy, H. E. Elsayed-Ali Jan 2005

Indium Growth On Si(100)-2 X 1 By Femtosecond Pulsed Laser Deposition, M. A. Hafez, M. S. Hegazy, H. E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Indium was grown on Si (100) -2×1 at room temperature by femtosecond pulsed laser deposition. Reflection high-energy electron diffraction (RHEED) was performed in situ to study film morphology and in-plane lattice spacing. Indium was found to grow on Si (100) -2×1 by the Stranski-Krastanov mode. The initial two-dimensional In layer formed in the In-2×1 structure with a lattice constant of 3.65 Å. The full-width at half-maximum (FWHM) of the specular peak decreased during the growth, indicating an increase of the In islands size. Further In growth on the initial In-2×1 layer showed the formation of hexagonal, elongated, and hemispherical islands …

Go to article

Anisotropic Diffusion Of N-Butane And N-Decane On A Stepped Surface, Shrijay Subramaniyan, Jee-Ching Wang Jan 2005

Anisotropic Diffusion Of N-Butane And N-Decane On A Stepped Surface, Shrijay Subramaniyan, Jee-Ching Wang

Chemical and Biochemical Engineering Faculty Research & Creative Works

The diffusion of single n-butane and n-decane molecules on a model stepped surface, Pt(655), and on a corresponding flat surface, Pt(111), is investigated using molecular-dynamics simulations and anisotropic united atom model. The surface step on Pt(655) causes the alkane molecules to adsorb on the lower terrace in all-trans conformations with their long molecular axes adjacent and parallel to the step edge, and to diffuse anisotropically along the surface step via a constant wiggly motion without rotation or marked deviation from the parallel adsorption configuration. At relatively high temperatures, the alkane molecules can temporarily break away from the step edge but …

Go to article

Measurement And Prediction Of Pressure Drop In Pneumatic Conveying: Effect Of Particle Characteristics, Mass Loading, And Reynolds Number, Kimberly H. Henthorn, Kinam Park, Jennifer S. Curtis Jan 2005

Measurement And Prediction Of Pressure Drop In Pneumatic Conveying: Effect Of Particle Characteristics, Mass Loading, And Reynolds Number, Kimberly H. Henthorn, Kinam Park, Jennifer S. Curtis

Chemical and Biochemical Engineering Faculty Research & Creative Works

This paper reports the effect of Reynolds number, mass loading, and particle shape and size on pressure drop in a vertical gas-solids pneumatic conveying line. We isolate the effect of one variable while holding all others constant. A commonly used pressure drop correlation and a state-of-the-art multiphase computational fluid dynamics (CFD) models are then assessed by comparing their predictions to experimental data. Deficiencies in the models and the correlation are identified, and possible modifications are proposed. The most notable deficiency is the inability of both the experimental correlation and the CFD model to accurately predict the pressure drop for gas-solids …

Go to article

First Prev Next Last