Chemical Engineering Commons^™

Tuning The Activity And Stability Of Platinum Nanoparticles Toward The Catalysis Of The Formic Acid Electrooxidation, Islam M. Al-Akraa, Bilquis A. Al-Qodami, Santosh Sridhar Mysore Dr, R. Viswanatha Dr, Abdul Kareem Thottoli, Ahmad M. Mohammad

Chemical Engineering

No abstract provided.

Synthesis And Characterization Of Chitosan Based Catalyst For Catalysis Applications, Mostafa Radwan

Chemical Engineering

In this research, chitosan based catalyst synthesis and characterization was investigated for different application in catalysis as chitosan based catalyst was combined with metal oxides in order to be used in dye removal of methyl orange (MO). Diluted acetic acid was used to dissolve chitosan then different percentages for metallic ions were mixed with diluted chitosan and then, 500 μL were added to the sample to reduce the metal salts then, microwave was used to heat the mixture for 5 minutes and then dried at 80-100 °C. Finally, X- ray diffraction was used to confirm the catalyst prepared. The aim …

Enhanced Glucose Electrooxidation At Ni-Cu Binary Oxide Nanocatalyst, Islam M. Al-Akraa, Mahmoud M. Abouzaid Eng, Yaser M. Asal Mr, Ahmad M. Mohammad Prof

Chemical Engineering

The aim of this study is to fabricate a nickel (NiOx) and copper (CuOx) oxide nanocatalyst on a glassy carbon (GC) electrode (will be abbreviated as Ni-Cu/GC) for glucose oxidation (GO). A sequential electrodepositon mode was applied to assemble NiOx and CuOx in the fabrication scheme. The optimization of Ni loading on the GC surface (will be abbreviated as Ni/GC electrode) was achieved first to attain the maximum catalytic efficiency in terms of the specific current toward GO. This (409 Ag1)was obtained by applying 15 mC/cm2 in the deposition of Ni. However, unfortunately the NiOx/GC could not support a long-term …

Development Of Novel Adsorbent For Industrial Waste Water Treatment, Islam M. Al-Akraa, Hassan M. Shehata Eng, Dalia A. Ali Eng., Hoda A. Elsawy Dr

Chemical Engineering

The main objective of this research project is to perform some experimental procedures to inform the ability of the novel adsorbent used in this project. The chemical modification of the adsorbent is the chemical oxidation of pure powder chitosan using some specific redox pairs which are potassium dichromate and sodium bisulphite. After preparing the modified chitosan, there are some parameters that must be discussed during the adsorption process. The first parameter is the time parameter, showing experimentally the optimum time for adsorption under certain conditions by collecting values of absorbance and concentration of thymol blue adsorbed after the process from …

Preparation Of Ceramic Membranes From Sludge Waste, Mai H. Roushdy

Chemical Engineering

Ceramic tiles industry produces industrial waste wit large amount which become a worldwide problem. Ceramic sludge produced from ceramic tiles wastewater treatment plant is routinely discarded as a useless waste. The aim of this paper is to recycle the ceramic sludge waste to be used as raw material for ceramic membrane production. The ceramic sludge was collected, dried, and characterized by mineralogical composition (XRD), thermal analysis (DTA and TGA), and chemical composition determination (XRF). The support ceramic membrane samples were formed, pressed, dried then fired using temperatures from 1050 to 1200 °C for 1 to 3 hours. Verification parameters were …

Preparation And Characterization Of Ceramic Nanofiltration Membrane Prepared From Hazardous Industrial Waste, Shereen Kamel Amin, Mai Hassan Roushdy, Heba Mohamed Abdallah, Ahmed Mostafa, Magdi Fouad Abadir

Chemical Engineering

Kiln rollers, which are widely used in ceramic tiles production, are usually subjected to surface grinding to remove the contaminations. The resulted fine powder is considered useless waste and a hazardous source of environmental pollution particularly as it contains health‐threatening fine free silica. In the present paper, the grind waste from kiln rollers was reused as raw material in the fabrication of nanofiltration cerramic membrane. The samples of produced ceramic membranes were formed into disks by adding 15% (by weight) organic binder solution with 2% concentration, then pressed at 35 MPa, dried and fired at temperatures range from 1100°C to …

Effect Of The Electrodeposition Potential Of Platinum On The Catalytic Activity Of A Pt/Gc Catalyst Toward Formic Acid Electro−Oxidation, Islam M. Al-Akraa, Bilquis A. Al-Qodami Ms., Ahmad M. Mohammad Prof

Chemical Engineering

The electrocatalytic activity of platinum (Pt)–modified glassy carbon (GC) (referred as Pt/GC) electrodes toward the formic acid electro−oxidation (FAO) was investigated. The Pt deposition on the GC substrate was carried out by a potentiostatic technique at different potentials (from 0.2 V to −0.2 V vs. Hg/Hg2Cl2/KCl (sat.) reference electrode) and the corresponding influence on the catalytic activity toward FAO was monitored. The electrocatalytic inspection revealed a potential role for the Pt deposition potential in boosting the catalytic efficiency of the catalyst toward FAO and further in mitigating the CO poisoning that eventually deactivate the catalyst. Interestingly, the highest activity toward …

A Spin-Coated Tiox/Pt Nanolayered Anodic Catalyst For The Direct Formic Acid Fuel Cells, Islam M. Al-Akraa, Ahmad M. Mohammad Prof

Chemical Engineering

The CO poisoning of the platinum anodic catalyst which typically functions the catalytic deterioration of the direct formic acid fuel cells could be minimized with a simple modification for Pt with titanium oxide. The fabrication scheme involved the spin-coating of a Ti precursor onto a Pt thin layer that was physically sputtered onto a Si substrate. The whole assembly was subjected to a post-annealing processing to produce the TiOx layer (60 nm) in a porous structure (mostly Anatase) atop of the Pt surface. The porous nature of the TiOx layer permitted the participation of Pt in the electrocatalysis of the …

Development Of Novel Adsorbent For Industrial Waste Water Treatment, Hassaan M. Shehata, Dalia A. Ali, Islam M. Al-Akraa Dr, Hany A. Elazab, Hoda A. Elsawy Dr

Chemical Engineering

The main objective of this research project is to perform some experimental procedures to inform the ability of the novel adsorbent used in this project. The chemical modification of the adsorbent is the chemical oxidation of pure powder chitosan using some specific redox pairs which are potassium dichromate and sodium bisulphite. After preparing the modified chitosan, there are some parameters that must be discussed during the adsorption process. The first parameter is the time parameter, showing experimentally the optimum time for adsorption under certain conditions by collecting values of absorbance and concentration of thymol blue adsorbed after the process from …

Polyvinylpyrrolidone - Reduced Graphene Oxide - Pd Nanoparticles As An Efficient Nanocomposite For Catalysis Applications In Cross-Coupling Reactions, Hany A. Elazab, Tamer T. El-Idreesy

Chemical Engineering

This paper reported a scientific approach adopting microwave-assisted synthesis as a synthetic route for preparing highly active palladium nanoparticles stabilized by polyvinylpyrrolidone (Pd/PVP) and supported on reduced Gra-phene oxide (rGO) as a highly active catalyst used for Suzuki, Heck, and Sonogashira cross coupling reactions with remarkable turnover number (6500) and turnover frequency of 78000 h-1. Pd/PVP nanoparticles supported on re-duced Graphene oxide nanosheets (Pd-PVP/rGO) showed an outstanding performance through high catalytic activ-ity towards cross coupling reactions. A simple, reproducible, and reliable method was used to prepare this efficient catalyst using microwave irradiation synthetic conditions. The synthesis approach requires simultaneous reduc-tion …

Decorative Articles Based On Polymeric Materials, Bassant Hussein, Yasser M. Asal, M. A. Radwan, M. A. Sadek, Hany A. Elazab

Chemical Engineering

The aim of the research is to create decorative articles based on polymeric materials, study the effects of fillers and the type of moulds that it can cope with the exothermic reaction nature of resin to create a scientific background on the usage of the resins in daily life products. The polymeric materials that will be concentrated on are the unsaturated polyester resins and epoxy resins. The unsaturated polyester is of many types and chemical constituents, the used experimentally is a general-purpose type and the epoxy also have different types and the used is a commercially 3D floor coating type. …

Microwave Assisted Synthesis Of Binary Metallic Oxides For Catalysis Applications, Abdelrahman Mostafa Kamal, Sherif Bahgat, Mohammed Hammam, M. A. Radwan, M. A. Sadek, Hany A. Elazab

Chemical Engineering

Herein, versatile, and reproducible method to prepare binary metal oxides via microwave assisted synthesis. Catalysts are substances that basically speeds up chemical reactions. Ideally, bonds are formed between the catalysts and the reactants. Also, catalysts permits formation of products from the reactants. These formed products, splits off the catalyst without affecting or changing it. Catalytic kinetics studies the correlate chemical reaction rate with some properties of reactants and/or products for instance; temperature, concentration and pressure. The aim of the project is to prepare pure and bi-metal iron based catalyst by co-precipitation method and to characterize the prepared sample using X-ray …

Novel Adsorbent For Industrial Wastewater Treatment Applications, Ahmed Y. Zakaria, Dalia A. Ali, Islam M. Al-Akraa, Hoda A. Elsawy, Hany A. Elazab

Chemical Engineering

In this study, the hydroxyapatite powder is investigated for both of methylene blue and thymol blue in aqueous solution. The physical and chemical properties of the adsorbent were evaluated systematically using the different techniques including Microsoft Excel programming, linear regression model and also the coefficient of determination. Batch adsorption experiments were conducted to determine the effect of contact time, solution pH, initial dye concentrations, and also the adsorbent dosage on adsorption. The adsorption kinetic parameters confirmed the better fitting of pseudo-second order kinetic model for both of methylene blue and thymol blue. The isotherm data of methylene blue and thymol …

Composite Materials Based On Twaron And Nano Materials, Omnia Hamdy, Remon A. Mankarious, M. A. Radwan, M. A. Sadek, Hany A. Elazab

Chemical Engineering

This research aims to participate in producing body shield that can overcome pervious drawbacks using behaviour of shear thickening fluid. Initially, the rheological behaviour of silica-polyethylene glycol shear thickening fluid is examined at different concentrations. Then, ballistic fabric samples are impregnated into silica-polyethylene glycol shear thickening fluid at various concentrations of silica and tested using gas gun simulating real ballistic threat. After that, the impact of rubbery hot water pack filled with around 66.67 wt% starch in water is tested using gas gun. Results showed as the concentration of silica increases, the indentation depth in the impregnated fabric decreases which …

Decorative Articles Based On Polymeric Materials, Yaser M. Asal Mr., M. A. Radwan, Hany A. Elazab Dr, Bassant Hussein, Mohamed A. Sadek

Chemical Engineering

The aim of the research is to create decorative articles based on polymeric materials, study the effects of fillers and the type of moulds that it can cope with the exothermic reaction nature of resin to create a scientific background on the usage of the resins in daily life products. The polymeric materials that will be concentrated on are the unsaturated polyester resins and epoxy resins. The unsaturated polyester is of many types and chemical constituents, the used experimentally is a general-purpose type and the epoxy also have different types and the used is a commercially 3D floor coating type. …

Hydrothermal Preparation Of Palladium Supported On Magnetite For Catalysis Applications, Hany A. Elazab, S. A. Hassan, M. A. Radwan, M. A. Sadek

Chemical Engineering

Herein, versatile, and reproducible method to prepare Pd/Fe3O4 via hydrothermal synthesis. The vital role of this catalyst is in its potential use in CO oxidation catalysis. The Pd/Fe3O4 shows a distinctive activity. TEM images confirmed that Pd nanoparticles of 8-12 nm have a well dispersion on the surface of magnetite (Fe3O4). Moreover, the prepared catalyst is recycled with remarkable catalytic activity. This outstanding activity is mainly a direct result of the strong metal-support interaction. The defect sites in the reduced iron oxide act as nucleation centers that enable anchoring of Pd nanoparticles leading to prevention of agglomeration.

Facile Microwave-Assisted Synthetic Approach To Palladium Nanoparticles Supported On Copper Oxide As An E±Cient Catalyst For Heck And Sonogashira Cross-Coupling Reactions, Hany A. Elazab Dr

Chemical Engineering

A simple green method for the synthesis of highly active palladium nanoparticles embedded on copper oxide as an efficient catalyst for ligand–free Heck cross–coupling reactions is developed. The approach is based on simultaneous chemical reduction of an aqueous solution of palladium and copper salts in microwave using hydrazine hydrate as the reducing agent. Full characterization of the catalyst with transmission electron microscope (TEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction spectroscopy (XRD), reveal a size range of 25 ± 2 nm for the generated catalyst nanoparticles. The use of the generated Pd/CuO nanoparticles is highly advantageous due to the use …

Microwave-Assisted Synthesis Of Graphene Supported Hexagonal Magnetite For Applications In Catalysis, Hany A. Elazab, M. A. Radwan, M. A. Sadek

Chemical Engineering

Herein, we report a rapid one-step synthetic method using microwave irradiation for growing magnetite nanocrystals on reduced graphene oxide sheets. This developed strategy allows decorating graphene sheets with magnetite nanocrystals of well-defined morphology as cubes using microwave-driven reduction of iron chloride using hydrazine hydrate as a reducing agent. The size and shape control was achieved via fine-tuning of the reaction conditions. The obtained results demonstrate the applicability of this microwave synthetic approach to control the morphology of the magnetite nanocrystals anchored on graphene sheets. Moreover, graphene sheets will enhance the nucleation and growth of magnetite nanoplates anchored on graphene. This …

Pd Nanoparticles Supported On Copper Oxide Prepared Via Microwave – Assisted Synthesis: An Efficient Catalyst For Suzuki Cross-Coupling, Hany A. Elazab Dr

Chemical Engineering

We report here a scientific investigation of a simple and versatile synthetic rote for the synthesis of palladium nanoparticles decorated with copper oxideand supported on reduced Graphene oxide (rGO) as a highly active catalyst usedfor Suzuki, Heck, and Sonogashira cross coupling reactions with remarkable turnover number (7000) and turnover frequency of 85000 h^-1. Pd-CuO nanoparticles supported on reduced Graphene oxide nanosheets (Pd-CuO/rGO) exhibited an outstanding performance through high catalytic activity towards cross coupling reactions. A simple, reproducible, and reliable method was used to prepare this efficient catalyst using microwave irradiation synthetic conditions. The synthesis approach requires simultaneous reduction …

Facile Synthesis Of Reduced Graphene Oxide-Supported Pd/Cuo Nano-Particles As An Efficient Catalyst For Cross-Coupling Reactions, Hany A. Elazab Dr

Chemical Engineering

The present communication reports a scientific investigation of a simple and versatile synthetic route for the synthesis of palladium nanoparticles decorated with copper oxide and supported on reduced graphene oxide (rGO). They are used as a highly active catalyst of Suzuki, Heck, and Sonogashira cross coupling reactions with a remarkable turnover number of 7000 and a turnover frequency of 85000 h-1. The Pd-CuO nanoparticles supported on reduced graphene oxide nanosheets (Pd-CuO/rGO) exhibit an outstanding performance through a high catalytic activity towards cross coupling reactions. A simple, reproducible, and reliable method is used to prepare this efficient catalyst using microwave irradiation …

Recycling Of The Mixture Resulted From Sanitary Ware Waste, Roller Kiln Waste And Ceramic Tiles Sludge Waste In The Manufacturing Of Ceramic Floor Tiles, Mai H. Roushdy

Chemical Engineering

Ceramic tiles industry is a big source for wastes that have a bad effect on the environment. The first source of waste is associated with roller kilns as it needs a periodic surface grinding to its rollers which results in a waste powder. The second type of waste is ceramic tiles sludge which produced from a water treatment plant. The third waste is sanitary ware waste which coming out from sanitary ware industry. The main aim of this paper is to investigate the ability of substituting part of the main body mixture of floor tiles by these three types of …

Synthesis, Characterization And Selected Application Of Chitosan-Coated Magnetic Iron Oxide Nanoparticles, Hany A. Elazab Dr

Chemical Engineering

In this research, we report an efficient method to prepare highly active chitosan-coated magnetic iron oxide nanoparticles by implementing co-precipitation technique which is used for waste water treatment applications. Chitosan-coated magnetic iron oxide nanoparticles were synthesized and characterized using TEM, XRD, and XPS. A comparative study has been made between chitosan powder and chitosan coated with magnetic nanoparticles with respect to the rate of adsorption of copper from aqueous solution. It was also experimentally verified that chitosancoated magnetic iron oxide nanoparticles are much more effective in adsorption of heavy metals than chitosan powder and it takes just few minutes instead …

Synthesis And Characterization Of Dinitro Pentamethylene Tetramine (Dpt), M. M. Seleet, S. A. Hassanien, M. A. Radwan, M. A. Sadek

Chemical Engineering

Preparation of dinitro pentamethylene tetramine (DPT) through the action of nitrating mixture formed of ammonium nitrate and fuming nitric acid on hexamine in presence of acetic acid, acetic anhydride and p-formaldehyde has been carried out. DPT was also prepared from hexamine dinitrate which is an important intermediate appears through preparation of DPT from hexamine directly. Prepared DPT was purified and then characterized through the determination of melting point, element test, FTIR spectrometry, UV spectrometry, and high performance liquid chromatography "HPLC". The obtained results were reliable and consistent with the literature.

Physico-Chemical Characteristics Of Ethanol–Diesel Blend Fuel, Tarek M. Aboul-Fotouh, Eslam Alaa, M. A. Sadek, Hany A. Elazab Dr

Chemical Engineering

In this research we are discussing the physicochemical characteristics of sweet diesel after desulphurization alone and also these characteristics are tested with the adding of high purity HPLC ethanol (99.9%). Those fuel properties of ethanol blended with diesel were experimentally determined to find their stability and to increase their properties and efficiency in the diesel engines. First we made 4 blends of diesel with ethanol and the fifth sample was pure diesel. The samples were 0% ethanol and 100 % diesel, the second sample was 5% ethanol and 95 % diesel, the third sample was 10 % ethanol and 90% …

High Octane Number Gasoline-Ether Blend, Hany A. Elazab Dr

Chemical Engineering

Gasoline produced in Egypt is a low-grade gasoline that contains high concentration of harmful components that are having a toll on our environment. In addition, those pollutants cause countless diseases and deaths annually to the Egyptian population. This paper targets two main sectors in the production of commercial gasoline. The improvement engine efficiency through the upgrading of octane number is first experimented by using a blendstock that ranges from gasoline fractions and Isomerates. An optimum was then chosen depending on the results obtained from different tests. Through those experiments, it was determined which samples obeyed the EU regulation for transportation …

Recycling Of The Mixture Resulted From Roller Kiln Waste And Ceramic Tiles Sludge Waste In The Manufacturing Of Ceramic Floor Tiles, Mai H. Roushdy

Chemical Engineering

Ceramic tiles industry produced many types of wastes that are routinely discarded as stock piles. One of the environmental problems associated with roller kilns is the periodic need to grind its rollers which results in a waste powder. The second type of waste is ceramic tiles sludge which produced from a water treatment plant in the ceramic tiles factory. This paper investigates the probability of substituting part of the main body of floor tiles mixture by these two types of waste powder. Many Experiments were done on the raw materials. Rectangular tile specimens were molded, dried and fired. Linear firing …

A Simple And Effective Way To Overcome Carbon Monoxide Poisoning Of Platinum Surfaces In Direct Formic Acid Fuel Cells, Yaser M. Asal Mr., Islam M. Al-Akraa Dr, Sohair A. Darwish Ms

Chemical Engineering

A glassy carbon (GC) electrode modified with multi-walled carbon nanotubes (MWCNTs) and platinum nanoparticles (PtNPs), Pt/MWCNTs-GC, has been introduced for formic acid electro-oxidation (FAO). A similar loading of PtNPs has been conserved for a proper comparison between the Pt/MWCNTs-GC and the unmodified Pt/GC electrodes. The modification with MWCNTs could enhance the loading of PtNPs onto the GC electrode in a way that minimizes its agglomeration and increases its dispersion in the CNTs network. This not only increases the surface area exposed to the reaction but also interrupts the contiguity of the Pt active sites minimizing the adsorption of the poisoning …

A Promising Modification Of Pt Surfaces With Cnts For Decreasing Poisoning Impact In Direct Methanol Fuel Cells, Yaser M. Asal Mr., Islam M. Al-Akraa Dr, Aya A. Khalifa Ms.

Chemical Engineering

Direct methanol fuel cells (DMFCs) are clean energy sources that have many applications due to the high energy density of methanol as a fuel. However, this type of fuel cells (FCs) has limitations that are preventing it from being commercialized. One such limitation is the adsorption of intermediates such as CO into the surface of the Platinum (Pt) catalyst during methanol oxidation (MO) which deactivates its active sites, where the reaction is taking place, and leads to poisoning of the electrode over the long term. In this study, multi-walled carbon nanotubes (MWCNTs) have been introduced to the Pt-modified glassy carbon …

Follow-Up And Kinetic Model Selection Of Dinitro Pentamethylene Tetramine (Dpt), Hany A. Elazab Dr

Chemical Engineering

The Synthetic route of Cyclotetramethylene Tetramine is implemented through the reaction of hexamine and nitrating mixture that is formed as a result of a reaction between ammonium nitrate and fuming nitric acid. The reaction medium includes acetic acid, acetic anhydride and p-formaldehyde. This synthetic pathway is relatively long and both of hexamine dinitrate and Dinitro Pentamethylene Tetramine (DPT) are considered as the two main intermediate compounds. The former compound (hexamine dinitrate) was prepared, purified, and then characterized. Conversion of hexamine dinitrate into DPT has been followed up experimentally at different temperatures. Various factors including temperature and time has been investigated. …

Hydrothermal Synthesis Of Graphene Supported Pd/Fe3o4 Nanoparticles As Efficient Magnetic Catalysts For Suzuki Cross – Coupling, Hany A. Elazab Dr

Chemical Engineering

This research reports a reproducible, reliable, and efficient method for preparing palladium nanoparticles dispersed on a composite of Fe3O4 and graphene as an active catalyst with high efficiency for being used in Suzuki cross – coupling reactions. Graphene supported Pd/Fe3O4 nanoparticles (Pd/Fe3O4/G) exhibit a remarkable catalytic performance towards Suzuki coupling reactions. Moreover, the prepared catalyst recyclability was up to nine times without losing its high catalytic activity. The catalyst was prepared using hydrothermal synthesis; the prepared catalyst is magnetic in order to facilitate catalyst separation out of the reaction medium after reaction completion simply through using a strong magnet. This …