Chemical Engineering Commons^™

The Multivariate Statistical Analysis Of Abiotic Parameters Of The Lake Tanganyika Sub Catchment, Hudson Nkotagu

Tanzania Journal of Engineering and Technology (TJET)

Results from multivariate statistical analysis of abiotic parameters conducted during the dry season at 20 accessible sites on 8 rivers, 2 lakes and a dam covering the Lake Tanganyika sub catchment are discussed. Standard methods were used to determine the levels of abiotic parameters from water samples. Physical parameters including DO, EC, Eh, turbidity, temperature, pH and secchi transparency were measured in situ while chlorophyll a was determined in the laboratory. Nutrients such as NO3-, SiO2, PO4 3- and Fe2+ were determined along with HCO3-. Factor analysis resulted in four factors including increased primary productivity, redox conditions, dissolution, and reduction …

Investigation Of The Effect Of Particle Size On Groundnut-Oil Solvent Extraction, S Manyele

Tanzania Journal of Engineering and Technology (TJET)

An investigation of the effect of particle size on the performance of vegetable oil recovery by solvent extraction is reported. Experiments were conducted using soxhlet extractor, groundnuts and n-hexane. Samples were grouped into mean particle sizes of 0.25, 0.75, 1.3, 3.3, and 7.5 mm using standard sieves. The effect of particle size was studied for extraction time intervals of 1, 2, 3, 4, 5 and 8 hours. The oil yield, oil recovered per kg solvent used, kg solvent lost per unit time, and the rate of extraction (kg oil recovered per hour) decreased with increasing particle size. Meanwhile, the percent …

Software Engineering: A Fundamental Approach To Automate And Interface Medical Electronic Systems With Computers In Healthcare Systems, Hashim Twaakyondo

Tanzania Journal of Engineering and Technology (TJET)

The cost for application software and propriatry standards (i.e. data structure and formats) required for storing clinical datasets from electronic device cause the use of time-consuming paper-based documentation and/or the transfer of electronic lab records manually to the PC database systems in Mother-Offspring Malaria Study (MOMS) Laboratory Unit located in Morogoro Regional Hospital, Tanzania. We have explored the ability to extract laboratory results from Haematology analyzer machine for easy management, access and storage. The methodology and tools used during the study includes; site survey and hands-on practice for requirement engineering, visual basic 6.0 for interface design and Microsoft Access for …

Oaming Characteristics Of The Food-Industry Biological Wastewater Treatment Plant, Samwel V. Manyele

Tanzania Journal of Engineering and Technology (TJET)

Intensive foaming observed during aeration of the aerobic food industry wastewater treatment plant is presented. This study was conducted to establish the foaming characteristics using a pilot three-phase fluidized bed bioreactor (TPFBB). A fluidization column (0.2 m i.d. and 6 m high) was used. The TPFBB was loaded with variable masses of novel biomass support particles (BSP). Wastewater samples collected from a plant processing both vegetable oil (VOPWW) and soap (SPWW) were immediately introduced in the TPFBB for aeration. The characteristics studied include: variation of foam volume with time, foam multiplicity, foaming and foam collapse rates. The SPWW produced excessive …

Performance Of Aerobic Bioreactors During Treatment Of Tanning Industry Wastewater, Samwel V. Manyele

Tanzania Journal of Engineering and Technology (TJET)

The performance of aerobic bioreactors loaded with novel biomass support (the KMT® support particles) during the treatment of tanning industry wastewater is presented in this paper. The wastewater samples were collected from TANWAT Company in Njombe, which extracts tannins from barks of the wattle tree. The wastewater generated from T ANWAT is very acidic with high loading of organic compounds, which are very complex and difficult to biodegrade using conventional methods. The paper introduces a new technology for treatment of heavily loaded industrial wastewater, like tannins, that is the Three-Phase Fluidized Bed Bioreactor (TPFBB) which utilizes the KM'f® support particles. …

Geometric Programming As A General Method For Phase And Reaction Equilibrium Calculations, Godwill Mrema

Tanzania Journal of Engineering and Technology (TJET)

Geometric programming has been used to calculate a large mtmber ofdifferent ideal and non-ideal equilibria, including, for reaction and For non-ideal Systems the primal program is solved a number Of times With the nan-ideal terms fixed each time. After each primal solution, the nan-ideal terms are "'hdated using the corresponding dun! solution. This iteration generally converges. We have included one counter-example, where the failure is caused by the equation Of state, which Cannot giu• correct roots.

Socio-Economic Impacts Of Computer Viruses In Tanzania, M Victor

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on a research project conducted with an objective of identifying and assessing various approaches used by different computer users (Management, System Administrators and end users) in Tanzania to combat computer viruses (CVs), and to assess users' awareness level on CVs. Specifically, the study aimed at assessing the awareness level on CVs to the Tanzanian business community; analyze the socio -economic impact caused by CVs in Tanzania and; assess existing methods, capacity and limitations on controlling CVs in Tanzania. Data was collected using both questionnaires and interview from financial institutions such as NBC and BOT, and telecommunications sector …

The Decomposition Kinetics Of Solids Thermodynamic Evidence For The Enthalpy Driven Cooling Of Reaction Environment Part 2, Akwilapo D

Tanzania Journal of Engineering and Technology (TJET)

The analysis of non-isothermal kinetic data for the decomposition of calcium carbonate, CaC03 (s) ~ CaO (s) + C02 (g) in flowing nitrogen, shows that the decomposition of solids is accompanied by self-cooling/heating of the reaction environment depending on the sample mass and heating rate. The correctness of the kinetic model is established by the calculation of the enthalpy change of the reaction. This is the thermodynamic evidence of endothermic enthalpy driven cooling of the reaction environment. The enthalpy change LJH = 179.33 kJmol-1 estimated from this work for the dissociation of CaC03 is in agreement with LJH = 179.17 …

Gasification Kinetics Of Ultrafine Coal Char Oxidation In Flame Reactions, G John

Tanzania Journal of Engineering and Technology (TJET)

Pulverized coal combustion is exceedingly complex with a  vast number of variables. In order to avoid the complications associated with the burning of coal char, a controlled study has been made of the oxidation of fine graphite in laminar methane-air flame as a contribution to the understanding of the more complex phenomena of the gasification kinetics of the char. The burning of methane is equivalent to the burning of volatiles and graphite oxidation is similar to that of coal char. Aspects of this have been simulated in experimental and computational studies of 4pm diameter graphite particle burning in methane -air …

Effectiveness Of Hot Isostatic Pressing On Healing Oxide Film Defects In Cast Aluminium Alloys, C Nyahumwa

Tanzania Journal of Engineering and Technology (TJET)

Hot isostatic pressing (hipping) of cast aluminium alloys is recognized as a means of providing improved internal soundness and mechanical properties of the castings. However, little is known about the limitations and potential benefit of the hipping process to produce reliable aluminium alloy castings containing oxide film defects due to turbulently filling of moulds. In this study, oxide film defects and fatigue lives of turbule''Zt filled unfiltered AI-7Si-Mg alloy castings have been characterised in as-cast and hipped. conditions to quantify the effectiveness of hot isostatic pressing on healing oxide film defects in the castings. The average fatigue life and fatigue …

Ceramic Properties Of Chimala Kaolin Clay, Leonard Akwilapo

Tanzania Journal of Engineering and Technology (TJET)

The physico-chemical properties of kaolinite clays occurring in abundance near Chimala were studied with a view of finding out their suitability in sanitary ware production. The viscosity of the clay was found to be within the range acceptable in industrial application (≤ 500 cp for 70% solids), enhancing its prospects for the manufacture of slip cast shapes with satisfactory properties. The chemical composition of the clay reveals a high content of Fe₂O₃, 1.48%, which is expected to affect the translucency and colour of the finished ware. However, such quantity would not have detrimental effects in the production of sanitary ware. …

Degradation Of Waterfront Reinforced Concrete Structures At The Port Of Dar Es Salaam, I Sanga

Tanzania Journal of Engineering and Technology (TJET)

The paper summarises the results of an investigation done on piers at the Dar es Salaam Port. The problem facing these structures and marine facilities is their exposure to aggressive environmental phenomena. The paper presents an investigation of the strength and corrosion of concrete seaport piers so as to determine degradation of the reinforced concrete waterfront structures in the port of Dar es Salaam. For instance the structures at a dhow quay terminal had been in use for about 100 years. The facility was in bad condition as the concrete had been badly damaged due to corrosion. Some of the …

Quality Of Common Salt In The Tanzanian Market, Kamwanya E

Tanzania Journal of Engineering and Technology (TJET)

The quality of edible salts in the Tanzanian market has been studied by comparing the levels of iodine, heavy metals, and non-metals. Among the 19 analyzed local salt samples, only two of them—Kipepeo salt (76.67 mg/kg) and Super salt (79.95 mg/kg)—met the recommended level of iodine as per TBS (Tanzania Bureau of Standards) specifications. Other brands have iodine levels below the TBS specification.

Comparative Study Of The Dynamics Of Circulating Fluidized Bed Riser And Downer Of Equal Diameters, Samwel V. Manyele

Tanzania Journal of Engineering and Technology (TJET)

The microscopic flow dynamics of the 100-mm internal diameter riser/downer circulating fluidized bed (CFB) unit were monitored using a solids concentration fiber optic probe. The comparison was conducted by comparing radial profiles Of the dynamic parameters derived from time-series analysis techniques (statistical and chaos analyses). The solids concentration signals used were recorded under similar operating conditions (gas velocity of 8.0 m/s and solids flux of 100 kg/m2s). Similar axial elevations were compared (entrance and fully developed sections of die reactors). A1 each loca!ion, the signals were sampled a! afrequency of 970 Hz for duration of 30 seconds. It was observed …

Participatory Evaluation And Improvement Of Cassava Processing Machines For The Eastern Zone Of Tanzania, V Silayo

Tanzania Journal of Engineering and Technology (TJET)

Cassava processing machines previously introduced in Tanzania were chippers and graters of the International Institute Of Tropical Agriculture (IITA) design. Popularization of such machmes in Tanzania required thorough participatory testing with stakeholders. When tested with farmers in Muheza and Kibaha districts average throughputs were 11-18 kg/h, 752 kg/h and 270 kg/hfor the manual chipper, engine-powered chipper and the engine-powered grater, respectively. Despite their low throughputs the manual chipper and the grater were Veo difficult to operate, and therefore demanded improvement. Improvement on these machines included modifications on the design for increased throughput, ease of operation and safety. The improved machines …

Aeration Efficiency Of A Three-Phase Fluidized Bed Bioreactor During Food Industry Wastewater Treatment, S Manyele

Tanzania Journal of Engineering and Technology (TJET)

The implementation Of a three-phase fluidized bed bioreaclor (TPFBB) in food- processing wastewater (FPW'W) treatment is reported. This study includes the modification Of the air distributor (plate design and gas-liquid mixing) for the bioreactor and resting of its aeration efficiency under different liquids. The aeration efficiency for wastewater samples collected from a soft drink processing industry and tannin processing industry (TANWA T) and tap water were compared. The aeration efficiency parameters studied include bed expansion, air holdup. volumetric oxygen mass transfer coefficient, and alpha factors. The variation of these parameters With air flow rates were studied at different liquid heights, …

Mathematical Simulation Of The Influence Of Volatile Ma•Rrer Cloud On Heterogeneous Ignition Of Single Coal Particles, Hassan Ratal Ambula

Tanzania Journal of Engineering and Technology (TJET)

Asimple model has been developed to predict the heterogeneous ignition temperature for single coal particles under conditions of negligible, natural and forced convections. These conditions cause different sizes Of volatile matter cloud that surround the coal particle. The model is based on the ignition Of a single coal particle heated by irradiation from spot heaters in a cold (ambient) surrounding. Energy from the particle surface oxidation, volatile matter combustion and physical heating from the spot heaters are all included in rhe particle energv balance. General ignüion criterion is used to determine the ignition point. The agreement between the experimental and …

Review Of The Product Development Process And Information Flow In The Manufacturing Industry: Problems And A Possible Wav Forward, E Opiyo

Tanzania Journal of Engineering and Technology (TJET)

No abstract provided.

Centrifugal Extraction Of Avocado Oil From The Pulp, J. W. Ntalikwa

Tanzania Journal of Engineering and Technology (TJET)

Absract

The Inclusion Behaviothe Inclusion Behavior Of Sodium Compounds In Sub-Micron Particles Formed During Coal Combustionr Of Sodium Compounds In Sub-Micron Particles Formed During Coal Combustion, Iddi Mkilaha

Tanzania Journal of Engineering and Technology (TJET)

During combustion of coal, biomass and sewage sludge, metallic compounds especially alkali metals such as sodium and potassium vaporize and form fumes which are emitted with the exhaust gases. These fumes are corrosive to the turbine blades of power plants. To minimize corrosion, efforts have been made to control the condensation phase of these metals. In this study, the evolution and inclusion of sodium in sub-micron particles was investigated using a drop tube furnace and a low-pressure impactor (LPI). Four types of coal with different chemical properties were tested. The results suggest that a reaction-controlled mechanism and nucleation via chemical …

Surface Titration Of Colloidal Alpha-Alumina, J. W. Ntalikwa

Tanzania Journal of Engineering and Technology (TJET)

The surface charge density (σ₀) of colloidal alumina (α-Al₂O₃) suspended in 1:1 electrolytes (NaCl, NaNO₃, CsCl and CsNO₃) at different electrolyte concentration (c₀) was determined using acid-base titration. The data were described in terms of the Triple Layer Model (TLM) of electric double layer. It was observed that the polarity of σ₀ could be varied through a point of zero charge (PZC) by varying the pH of the suspension. The PZCs were observed to occur at pH = 7.8 ± 0.1, 7.6 ± 0.2, 8.5 ± 0.1 and 8.3 ± 0.1 in NaCl, NaNO₃, CsCl and CsNO₃, respectively. It was …

Simulation Of The Communication Process In A Pin Mill, Ambrose J. M. Itika

Tanzania Journal of Engineering and Technology (TJET)

Prediction of the performance of comminution equipment by mathematical models and simulation poses a great challenge to the chemical engineer. This paper describes the simulation of grinding results obtained using an impact mill. Single particle results have been used to generate breakage and selection coefficients that were used for the evaluation of the model. Results have shown that simulation model is in good agreement with the experimental data obtained at a circumferential speed above 60 m/s. At lower speeds, the models shows only partial agreement in the middle particle size ranges. The application of the model is therefore limited for …

Discrete Element Modelling Of The Abrasive Dehulling Process Of Sorghum And Millet, E. L. Lazaro

Tanzania Journal of Engineering and Technology (TJET)

The abrasive dehulling process of sorghum and millet was modelled using a three-dimensional discrete element model. The model was validated by comparison between experimental and simulation results. Good correlation between experimental and simulation results was obtained. Several numerical experiments were also carried out using the developed model to investigate the influence of mill and grain parameters on dehulling of sorghum and millet. The simulated results correlated well with experimental results from literature. The developed model therefore provides a simple and cheap tool, which can be used to study the dehulling process in more detail than, is currently possible using the …

Properties Of Rice Husk Particle Boards Bonded By A Blend Of Tannin-Cnsl Resin, J. V. Tesha

Tanzania Journal of Engineering and Technology (TJET)

There are vast quantities of agricultural residues available in Tanzania. Rice husk being amongst those residues is reported to have low resistance to alkalis, high silica content, and have short fibres. These factors have made rice husks not attractive raw materials in panels’ production. However, it has been demonstrated that rice husks can be used to develop panel products of low cost and good performance if appropriate indigenous technologies and affordable binders that can bind siliceous materials are used.

This paper provides a summary on the study of the effectiveness of the binding characteristics of a blend of natural adhesive …

Evaluation Of Corrosion Inhibitor On Pre-Corroded Carbon Steel In Co2 Medium By Impedance Spectroscopy, Joseph Buchweishaija

Tanzania Journal of Engineering and Technology (TJET)

The effect of pre-corrosion of carbon steel on the performance of a commercial amine based fatty acid corrosion inhibitor, KI384, was investigated in formation water solutions saturated with CO₂ using electrochemical impedance spectroscopy (EIS) measurements. The investigation was performed at constant partial pressure of CO₂ using an autoclave system with Rotating Cylinder Electrodes (RCE). Carbon steel was pre-corroded for periods up to 7 days at 35 and 80 °C in the test solution prior to inhibitor injection. The results showed that when KI384 was applied on non-corroded carbon steel specimen, high inhibitor performance (99.8 %) was achieved independent of temperature. …

Comparative Analysis Of H₂S Removal Ability Of Different Calcium-Based Absorbents Under Coal Gasification Conditions, Hassan Katalambula

Tanzania Journal of Engineering and Technology (TJET)

Calcium-based sorbents, such as limestone and dolomite are viable candidates for capturing pollutants in an in-situ coal gasification/desulphurisation process. Recently, scallop shell is also used as a Ca-based sorbent. However, the ability in capturing pollutants varies from one type to another and it also depends on the process involved. In this study, two types of limestone, scallop shell and dolomite were characterized and studied for H₂S absorption ability under the coal gasification conditions. The characterizations were done using Scanning Electron Microscope (SEM), X-ray Diffraction (XRD), Thermal analysis and Surface Area analysis. All of the samples showed a porous structure, and …

Electrokinetic Cha Raci'erisation Of Colloidal A-Alumina, J Ntalikwa

Tanzania Journal of Engineering and Technology (TJET)

Electrophoretic mobility (uD is an important rneasurable parameter in studying the electrokinetic properties of a colloid dispersion. This parameter is Often convened into zeta potential (C) Which piays a great role in thc description Of the stability towards aggregation Of dispersed particles. In this paper, measurements of Of colloidal a-alumina dispersed in various concentrations of electrolyte arc reported. It was observed that, the isoelectric points (the pH at which us = O) occurred at 7.52 ± 0.32, 8.05 ± 0.11 and 7,95 ± 0.18 in Naci, KCI and NaNOs respectively. The isoelectric point was observed to be a function Of …

Comparative Analysis Of Rng K-E And 'Standard' K-C Models For Fluid Flow Around A Cylinder, A Temu

Tanzania Journal of Engineering and Technology (TJET)

A two-dimensional computational scheme for simulating fluid flow around a cylinder was investigated. RNG (Re-NOrmalisation Group) and 'standard' turbulent closure models were used. simulation was implemented with assistance OfFLOW-3D computational fluid dynamics (CFD) code. The governing equation Of fluid motion, in Eulerian form, included body forces as well as surface forces. The computational model predictions for fluid velocity showed good agreement between the two models. Comparison Of the viscosities showed a large deviation from the two models, with RNG k-E model giving a better approximation. Comparison Of the velocity around the cylinder, as obtained from RNG k-c model, with approximation …

Production Of Biogas From Water Hyacinth: Effect Of Substrate Loading In Semi-Batch & Batch Operations, J Katima

Tanzania Journal of Engineering and Technology (TJET)

A study was carried out to establish the effect of substrate loading rate on the production of biogas from water hyacinth. The experiments revealed that the maximum methane yield in a batch process was 0.166 normal litre (NLVg Of volatile solids (VS) added at substrate concentration of 25 g dry mass'litre after five days of incubation. The maximum methane yield in a semi-batch process was 0.153 NWg VS added at 1.30 g VS'litre day and retention time Of 15 days.

Recyclability Of Modified Ps-Aq Pulps At Around Kappa 30, Rwaichi Minja

Tanzania Journal of Engineering and Technology (TJET)

Bleachable grade pulps prepared from Nonvegian softwood spruce chips while simulating possible alternatives of improving pulp yield by application Of polysulphide (PS) and anthraquinone (AQ) have been used in this study. The tests for recyclability were performed on hydrogen form pulps. The pulps considered were Iso- Thermal cooking (ITC) kraft pulp which was used as a reference pulp, conventional PS-AQ pulp, soda PS-AQ pulp and kraft PS-AQ pulp. The loss Of swelling ability (homification) Of the pulps, was determined by measurement of water retention value (W R V). The results showed that, PS-AQ pulps had similar or slightly better swelling …