Chemical Engineering Commons^™

High Performance Mixed-Matrix Electrospun Membranes For Ammonium Removal From Wastewaters, Shu-Ting Chen, Sumith Ranil Wickramasinghe, Xianghong Qian

Chemical Engineering Faculty Publications and Presentations

Mixed-matrix electrospun membranes were developed to investigate ammonium removal from low ammonium concentration wastewaters for the first time. Particles derived from the inexpensive zeolite 13X were successfully incorporated into polyethersulfone (PES) matrices. The fabricated mixed-matrix electrospun membranes demonstrate high ammonium removal capacity reaching over 55 mg/g_zeolite, more than 2.5 times higher than the previously fabricated mixed-matrix membranes via non-solvent induced phase inversion. Moreover, the membranes fabricated exhibit high permeability and ease of regeneration. Over 90% of total ammonium nitrogen (TAN) can be removed from low TAN wastewaters such as aquaculture wastewaters. In addition to zeolite 13X, other zeolite …

Economic Feasibility Of Mixed Plastic Waste Pyrolysis Using Twin Reactor System In Northwest Arkansas, Carol Rogers, Patricia Means, Renato Gonzalez, Kaida Sheets, Hayden Townsend

Chemical Engineering Undergraduate Honors Theses

Plastic waste generation is increasing at an unsustainable rate while recycling solutions remain stagnant. As a chemical means of recycling, mixed plastic waste pyrolysis can generate synthetic oil appropriate for use as fuel in power generation from plastic waste that otherwise accumulates in landfills. With the scaling of a commercial plastic pyrolysis process in Northwest Arkansas (NWA) modeled after an operational sawdust pyrolysis unit in Huntsville, Arkansas, economic analysis resulted in 26.3% internal rate of return. Therefore, construction of a commercial mixed plastic-to-fuel pyrolysis plant is economically justified and should be pursued. To effectively implement the proposed design, NWA must …

Machine Learning Representations For Optimization Of Process Systems, Logan Watts

Chemical Engineering Undergraduate Honors Theses

The optimal operation of chemical processes provides the foundation for optimization problems to determine the most effective way to operate or design a given process. Chemical processes can be represented as nonlinear systems of equations with decision variables, resulting in a problem that can be solved through nonlinear solvers. The downfalls of nonlinear solvers create the need for improved methods of finding globally optimal solutions to the design or operation of a chemical process. The project will seek to evaluate the use of artificial neural networks to approximate nonlinear systems of equations for the purpose of optimizing chemical processes. The …

Promotion Of Human Schwann Cell Proliferation Using Heparin/Collagen Coated Nerve Conduits, John Magness

Chemical Engineering Undergraduate Honors Theses

Often in the aftermath of an injury or surgery, the sense of touch and muscle control is lost in the affected area as nerves are damaged or severed and fail to grow back completely. The regeneration of the nerve cells can be promoted by treating the nerves with nerve conduits. Nerve conduits are hollow cylinders of bio-compatible materials that can be surgically implanted to the disconnected nerve to promote and direct the growth of nerves. The objectives of this research are to investigate the ability of nerve conduits treated with layer-by-layer coatings to promote the growth of Schwann cells, to …

Peptoid-Functionalized Gold Nanoparticles For Zika Virus Envelope Protein Detection, Meagan Olsen

Chemical Engineering Undergraduate Honors Theses

Detection and identification of viral pathogens is essential in providing effective and rapid medical treatment. Well-established detection methods can be expensive, slow, and sometimes unable to provide the needed sensitivity and specificity. The Zika virus is one clinically relevant pathogen that cannot be easily identified due to cross-reactivity with other viruses from the same family. Electrochemical sensors enhanced with peptoid-functionalized gold nanoparticles (AuNPs) are an alternative to traditional techniques that offers rapid, accurate, label-free pathogen detection for point-of-care diagnostics. To this end, a peptoid capable of binding to the Zika virus envelope protein was developed and its binding affinity for …

Garver Industrial Design Project: Designing A Full-Scale Reverse Osmosis Water Treatment Facility For The City Of Lawton, Oklahoma, Kayliana Warden, Marlando Collins, Sandrina Depaz, Reid Eakin, Reed Leasure, Vera Rodriguez

Chemical Engineering Undergraduate Honors Theses

A groundwater treatment facility was designed for Lawton, Oklahoma to address potential water scarcity due to drought conditions in southwest Oklahoma. The facility will produce five million gallons per day (MGD) of treated water. The plant will have the capacity of treating 4,085 gallons per minute of influent water at an 86% recovery. The water to be treated will come from the Arbuckle-Timbered Hills Aquifer. Studies have been conducted around the aquifer to identify the best well site locations.

A centralized treatment facility using reverse osmosis filtration as the main treatment technology has been designed. To prevent reverse osmosis membrane …

Development Of An Integrated Salt Cartridge-Reverse Electrodialysis (Red) Device To Increase Electrolyte Concentrations Of Human Blood Flow To Power Biomedical Devices, Caroline Campbell

Chemical Engineering Undergraduate Honors Theses

Emerging technologies in nanotechnology and biomedical sciences have led to an increase in biomedical implantable devices including cardiac pacemakers, artificial organs, drug pumps, and sensors. These devices require continuous stable and reliable power to operate, which creates the demand for the need to find a safe, reliable, and stable power source. A promising avenue for a power source for these devices is a miniaturized reverse electrodialysis (RED) biopower cell design that utilizes the salinity differences between bloodstreams that flow inside the human body. Initial results of the RED system demonstrate that higher gradient salinity differences between streams lead to a …

Remote Performance Modulation Of Ultrafiltration Membranes By Magnetically And Thermally Responsive Polymer Chains, Arijit Sengupta, Anh Vu, Xianghong Qian, Sumith R. Wickramasinghe

Chemical Engineering Faculty Publications and Presentations

Ultrafiltration membranes, that respond to an external magnetic field and local temperature have been developed. Surface-initiated activator-generated electron transfer (AGET) atom transfer radical polymerization (ATRP) has been used to graft poly(N-isopropylacrylamide) (PNIPAm) from the surface of 300 kDa regenerated cellulose membranes. The polymerization initiator was selectively attached to the entire membrane surface, only the outer membrane surface or only the inner pore surface. A superparamagnetic nanoparticle was attached to the end of the polymer chain. The DI water flux as well as the flux and rejection of bovine serum albumin were investigated in the absence and presence of a 20 …

Biopolymeric Materials For Tissue Regeneration, Cell Manufacturing, And Drug Delivery, David Alfonso Castilla-Casadiego

Graduate Theses and Dissertations

The development of materials for tissue regeneration, cell manufacturing, and drug delivery is possible by the manipulation of polymer properties and the use of three different techniques including layer-by-layer, electrospinning, and molding technique.

By applying the layer-by-layer technique over biomaterials, it is possible to develop polymeric multilayers that promote a more favorable environment for cellular functionality, increasing the possibility of improving their acceptance in the area of implantation. IRVASE demonstrated being a powerful technique that allows for a reliable characterization of the physical-chemical and thermal properties of the fabricated surfaces. This opens the possibility to monitor the design of surfaces …

Peptoid-Based Microsphere Coatings For Biomaterial Applications, Jesse Leland Roberts

Graduate Theses and Dissertations

Peptoids are peptidomimetic oligomers that predominantly harness similarities to peptides for biomimetic functionality. The incorporation of chiral, aromatic side chains in the peptoid sequence allows for the formation of distinct secondary structures and self-assembly into supramolecular assemblies, including microspheres. Peptoid microspheres can be coated onto substrates for potential use in biosensor technologies, tissue engineering platforms, and drug-delivery systems. They have the potential for use in biomedical applications due to their resistance to proteolytic degradation and low immunogenicity. This dissertation focuses on the physical characteristics and robustness of the peptoid microsphere coatings in various physiological conditions, along with their ability to …

Surface Modified Polypropylene Membranes For Treating Hydraulic Fracturing Produced Waters By Membrane Distillation, Tharaka Hawpe Gamage

Graduate Theses and Dissertations

Membrane distillation is an emerging technology for treating hydraulic fracturing flowback and produced waters. Suppression of membrane fouling by inorganic and polar and non-polar organic compounds is a challenge. Here polyhydroxyethyl methacrylate, polyacrylic acid, polvinylallyl imidazolium bromide and polyvinylhexyl imidazolium bromide chains have been grafted from the membrane surface. Fouling is initially due to adsorption of organic compounds followed by scale formation. When challenged with produced water, membranes modified with polvinylallyl imidazolium bromide chains provided the greatest resistance to fouling. For EC pretreated produced water and synthetic produced water that contained mainly inorganic species, the flux decline was much less.

Investigative Study Of Microalgal And Electrochemical Wastewater Treatment Systems And Modeling Of The Wafer-Enhanced Electrodeionization Using Supervised Learning, Humeyra Betul Ulusoy Erol

Graduate Theses and Dissertations

Wastewater has a serious impact on environment and public health due to its high concentration of nutrients and toxic contaminants. Without proper treatment, excess nutrients discharged in wastewater can cause a damage to the ecosystem such as undesirable pH shifts, cyanotoxin production, and low dissolved oxygen concentrations.

Main objectives of this dissertation work were to investigate i) the biofuel potential of P. cruentum when grown in swine wastewater, ii) the influence of four most commonly used ion exchange resins on the system efficiency and selectivity for the removal of sodium, calcium, and magnesium ions, and iii) the modeling of wafer-enhanced …

Peptoid Microsphere Coatings To Improve Performance In Sandwich Elisa Microarrays, Jesse L. Roberts, German R. Perez Bakovic, Shannon L. Servoss

Chemical Engineering Faculty Publications and Presentations

Enzyme-linked immunosorbent assay (ELISA) microarray performance is limited by low assay sensitivity and dynamic range. Increasing the surface area for reagent binding can help to improve performance, but standard techniques such as roughening the surface or adding a polymer coating lead to increased non-specific fluorescence and do not have reproducibly improved performance. Another approach to increase surface area is adding a microsphere coating on the surface. Poly-N-substituted glycine (peptoid) microspheres are ideal for this application due to low immunogenicity, protease-resistance, and biocompatibility. Peptoids are polymers with a backbone similar to peptides, but with the side chains appended to nitrogen rather …

Effects Of Resin Chemistries On The Selective Removal Of Industrially Relevant Metal Ions Using Wafer-Enhanced Electrodeionization, Humeyra B. Ulusoy Erol, Christa N. Hestekin, Jamie A. Hestekin

Chemical Engineering Faculty Publications and Presentations

Wafer-enhanced electrodeionization (WE-EDI) is an electrically driven separations technology that occurs under the influence of an applied electric field and heavily depends on ion exchange resin chemistry. Unlike filtration processes, WE-EDI can be used to selectively remove ions even from high concentration systems. Because every excess ion transported increases the operating costs, the selective separation offered by WE-EDI can provide a more energy-efficient and cost-effective process, especially for highly concentrated salt solutions. This work reports the performance comparison of four commonly used cation exchange resins (Amberlite IR120 Na⁺, Amberlite IRP 69, Dowex MAC 3 H⁺, and …

The Varied Thermal Response Of Magnetic Iron-Oxide Nanoparticles During Induction Heating In Liquid And Solid-Liquid Phase Change Mediums, Joshua Tompkins

Graduate Theses and Dissertations

This study investigates the induction heating response of uncapped iron oxide nanoparticles sonically dispersed as a nanofluid and mechanically distributed in solid phase change materials. The nanoparticles examined have a mean diameter of 14.42 nm and are magnetically heated in an alternating magnetic field at an amplitude of 72.6 kA/m at frequencies of 217, 303, and 397 kHz. Nanoparticle characterization was undertaken through transition electron microscopy, x-ray diffraction, and dynamic light scattering when in suspension. Carrier fluids were characterized through viscosity, heat capacity, and density measurements which were used in the calorimetric calculation of the specific absorption rate (SAR) of …

The Effects Of Solution Condition On Virus Filtration Performance, Fnu Namila

Graduate Theses and Dissertations

Virus filtration is an integral part of the downstream purification of mammalian cell culture-derived biotherapeutics to assure the viral safety of the products. Virus filtration membranes remove viruses based on a size-exclusion mechanism. Commercial parvovirus filers possess unique membrane structure and are designed to remove smaller non-enveloped parvoviruses with size 18-26 nm. However, some filters face issues, such as pre-mature fouling, the decline of filtrate flux, and reduction in virus retention. This doctoral dissertation focused on identifying the factors that influence the filtrate flux and the virus retention capability of commercial virus filters. The effects of solution pH and ionic …

Investigation Of Electrospun Nanofibers For Separation Applications, Shu-Ting Chen

Graduate Theses and Dissertations

Electrospun membranes are an attractive alternative to flat sheet membranes as absorbent with numerous advantages like high porosity, large specific surface area and ease of functionalization. This doctoral dissertation focuses on fabricating novel polymeric membrane adsorbents for protein separations and ammonium ion removal. Three distinctly different preparation methods including UV-initiated polymerization, atom transfer radical polymerization, and mixed-matrix formation, have been employed to fabricate the electrospun membranes. Overall, this study aimed to develop electrospun membranes with excellent separation efficiency for application in protein purification and ammonium ion removal.

Chapter 2 details the stepwise development of weak anion exchange membranes and subsequent …

What Difference Does A Catalyst Make?, Tammy Guthrie, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use different catalysts for the decomposition of Hydrogen Peroxide, to determine if different catalysts affect the energy that is generated during the reaction.

Nonlinear Dimensionality Reduction For The Thermodynamics Of Small Clusters Of Particles, Aditya Dendukuri

Graduate Theses and Dissertations

This work employs tools and methods from computer science to study clusters comprising a small number N of interacting particles, which are of interest in science, engineering, and nanotechnology. Specifically, the thermodynamics of such clusters is studied using techniques from spectral graph theory (SGT) and machine learning (ML). SGT is used to define the structure of the clusters and ML is used on ensembles of cluster configurations to detect state variables that can be used to model the thermodynamic properties of the system. While the most fundamental description of a cluster is in 3N dimensions, i.e., the Cartesian coordinates of …

A Study Of The Thermodynamics Of Small Systems And Phase Transition In Bulk Square Well-Hard Disk Binary Mixture, Gulce Kalyoncu

Graduate Theses and Dissertations

Under the umbrella of statistical mechanics and particle-based simulations, two distinct problems have been discussed in this study. The first part included systems of finite clusters of three and 13 particles, where the particles are interacting via Lennard Jones potential. A machine learning technique, Diffusion Maps (DMap), has been employed to the large datasets of thermodynamically small systems from Monte Carlo simulations in order to identify the structural and energetic changes in these systems. DMap suggests at most three dimensions are required to describe and identify the systems with 9 (N = 3) and 39 (N = 13) dimensions. At …

Analysis Of Blood Purification Studies On Oxone Mediated Tempo-Oxidized Nano Cellulose Mixed-Matrix Membranes, Tony Roller

Biomedical Engineering Undergraduate Honors Theses

End-stage renal disease (ESRD) is currently the ninth leading cause of death in the United States, and of the 661,00 Americans diagnosed with ESRD, approximately 468,800 were on hemodialysis in 2016. Hemodialysis refers to a technique where a machine combined with a membrane, often referred to as an artificial kidney, is used to clean blood by removing any waste such as urea, potassium, and other smaller waste products while preserving the concentrations and integrity of cells and proteins in the blood. It has been shown in artificial blood studies that cellulose nanomaterials, like TEMPO/Oxidized cellulose nanoparticles (TOCNs), can be integrated …

Electrodialysis Device For In Vivo Power Delivery, Jessica L. Orton

Biomedical Engineering Undergraduate Honors Theses

It is estimated that over 3 million cardiac pacemakers have been implanted in patients globally. Current lithium-iodine pacemaker batteries last an average of about 10 years before the entire pacemaker unit must surgically be replaced, increasing the patient’s risk of procedure-related complications. Therefore, it is necessary to investigate means by which to extend the pacemaker battery lifetime. The renal vein and renal artery in the body naturally produce a salinity gradient through the filtering work of the kidneys. This salinity gradient energy potential can be harnessed through reverse electrodialysis (RED). RED is an electrochemical process that harnesses the Gibbs Free …

Improving Pv Module Efficiency Through Cooling, Blake Bradley

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …

Removal Of Fluoride From Mine Water Via Adsorption For Land-Applied Soil Amendment, Ethan Phan, Adrian Damian, Kevin Le, Mary Johnson, Courtney Golman, Michelle Dopp, Jacqueline Payne

Chemical Engineering Undergraduate Honors Theses

The process of mining minerals and elements from ores and rocks creates acid rock drainage (ARD). This drainage is water that contains heavy metals and minerals that can be dangerous for human consumption or damaging to the environment. The mining industry has employed various water treatment methods to prevent these metals and minerals from being discharged into water sources such as ponds, lakes, and streams. Currently, the most used treatment process in the mining industry is a cost-effective high-density sludge (HDS) process. This method reduces the concentration of metals and elements with the use of lime/limestone. However, the concentration of …

Removal Of Fluoride From Mine Water Via Adsorption For Land-Applied Soil Amendment, Jacqueline Payne, Mary Johnson, Kevin Le, Michelle Dopp, Courtney Golman, Adrian Damian, Ethan Phan

Chemical Engineering Undergraduate Honors Theses

The process of mining minerals and elements from ores and rocks creates acid rock drainage (ARD). This drainage is water that contains heavy metals and minerals that can be dangerous for human consumption or damaging to the environment. The mining industry has employed various water treatment methods to prevent these metals and minerals from being discharged into water sources such as ponds, lakes, and streams. Currently, the most used treatment process in the mining industry is a cost-effective highdensity sludge (HDS) process. This method reduces the concentration of metals and elements with the use of lime/limestone. However, the concentration of …

Improving Pv Module Efficiency Through Cooling, Megan Reynolds

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …

Solution To Exide Technologies Inbatec Inefficiency, Spencer Christian, Shixuan Hou, Mary Fairley, Reagan Gilker, Covenson Latouche

Chemical Engineering Undergraduate Honors Theses

The inefficiency of the battery charging time in Inbatec Units 1 and 2 in the Exide Technologies Fort Smith was initially investigated by a student team in Fall 2019, and the investigation was continued into Spring 2020. The Exide Technologies facility in Fort Smith, Arkansas utilizes 13 Inbatec units to charge the lead-acid batteries. The Inbatec systems circulate the sulfuric acid solution through a cooling tower to maintain to optimal charging temperature. Previous analysis of the charging process for Inbatec Units 1 and 2 show the cooling tower have the capacity to quickly remove the excess heat in the sulfuric …

Solution To Exide Technologies Inbatec Inefficiency, Shixuan Hou, Reagan Gilker, Mary Fairley, Spencer Christian, Covenson Latouche

Chemical Engineering Undergraduate Honors Theses

The inefficiency of the battery charging time in Inbatec Units 1 and 2 in the Exide Technologies Fort Smith was initially investigated by a student team in Fall 2019, and the investigation was continued into Spring 2020. The Exide Technologies facility in Fort Smith, Arkansas utilizes 13 Inbatec units to charge the lead-acid batteries. The Inbatec systems circulate the sulfuric acid solution through a cooling tower to maintain to optimal charging temperature. Previous analysis of the charging process for Inbatec Units 1 and 2 show the cooling tower have the capacity to quickly remove the excess heat in the sulfuric …

Solution To Exide Technologies Inbatec Inefficiency, Mary Fairley, Reagan Gilker, Spencer Christian, Shixuan Hou, Covenson Latouche

Chemical Engineering Undergraduate Honors Theses

The inefficiency of the battery charging time in Inbatec Units 1 and 2 in the Exide Technologies Fort Smith was initially investigated by a student team in Fall 2019, and the investigation was continued into Spring 2020. The Exide Technologies facility in Fort Smith, Arkansas utilizes 13 Inbatec units to charge the lead-acid batteries.

The Inbatec systems circulate the sulfuric acid solution through a cooling tower to maintain to optimal charging temperature. Previous analysis of the charging process for Inbatec Units 1 and 2 show the cooling tower have the capacity to quickly remove the excess heat in the sulfuric …

Improving Pv Module Efficiency Through Cooling, Harrison Dawson

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …