Chemical Engineering Commons^™

Wetting Transition On 3d-Printed Featured Surface, Hannah Pineault

Williams Honors College, Honors Research Projects

The primary objective of this research project was to gain a better understanding of surface characteristics to produce a long-lasting superhydrophobic or superhydrophilic surface. In other words, when will a droplet of water remain on top of a featured surface and when does the transition occur to water filling the grooves of the surface? This research focused on how to best fabricate porous structures that would stay completely dry at all times by preventing the liquid from penetrating. In particular, we followed the behaviors of water droplets placed on top of 3-D printed featured surfaces with various geometries and surface …

Comparison Of The Effects Of Hofmeister Ions On Transition Temperature Of Two Thermoresponsive Polymers, Ashley Knight

Williams Honors College, Honors Research Projects

It has been hypothesized that poly(vinylmethylether) (PVME) could be used to replace poly(N-isopropylacrylamide) (pNIPAAM) in various thermoresponsive applications based on literature searches and previous lab experiments. PVME is cheaper and easier to process, and would make pNIPAAM applications more cost effective. In order to verify this, experimental data was gathered on the effects of four anions from the Hofmeister series (SO₄₂-, Cl-, I-, and SCN-) on the lower critical solution temperature (LCST) of pNIPAAM and compared to previous data collected on PVME. Commercial pNIPAAM from Sigma Aldrich and Polysciences were used. The reported LCST range for pNIPAAM is …

Investigation Of Surface Charge Using Faraday Bucket Measurements: Analysis On Electrospun Polyvinylidene Fluoride Fiber Mats, Ryan Kantenwein

Williams Honors College, Honors Research Projects

Piezoelectric polymer materials such as polyvinylidene fluoride exhibit beneficial properties for use in personal protective equipment (PPE) against viral contaminants and other foreign microparticles. The electrospinning process of this material allows for surface charge to develop over a controlled surface area. Kynar 761 at 10 wt% demonstrates increased surface charge after withstanding a flow of aerated NaCl particles from a TSI 8130 instrument. Utilizing voltage measurements from a Faraday bucket, 18 wt% Kynar 761 and MG-15 exhibit surface charge when undergoing an electrospinning process; however, Kynar MG-15 displays lower charge values than that of Kynar 761. Several critical factors such …

Simulation Of Water Loading In Filter Medium, Anthony Mole

Williams Honors College, Honors Research Projects

This research will model fluid flow through a filter plugged with water droplets using FlexPDE software. After simulations are run at various initial conditions, curves will be developed to correlate the permeability of the filter to variables like water droplet distribution and size.

Relating Modified Ergun's Equation To Hindered Settling Correlations, Ryan Zahniser

Williams Honors College, Honors Research Projects

Correlations were developed between the Modified Ergun’s and Hindered settling correlations under the condition of dense packing of particles in the bed. As the porosity of the slurry increases, so does the interference between particles in the solution which mimics the behavior of a packed or densely concentrated fluidized bed. The similarity between the two sets of conditions was modeled using mathematical equations to calculate settling velocities and pressure drops by means of the Hindered Settling correlations and Modified Ergun’s equation at porosities ranging from 0.4242 to 0.89. The results showed that a porosity of 0.52 and 0.009 ft particle …

The Effects And Motion Of An Air-Filled Cylinder Being Submerged In Water In The Axial Direction, Ethan Davis

Williams Honors College, Honors Research Projects

Submarines operate on the basis of a difference in relative densities between of vessel and the surrounding fluid. This principle is based on the force balance that exists between the total buoyancy force and the force due to gravity. Previous work focuses on the neutral buoyancy depths and velocities of object that once submerged, their buoyancy force is a constant along with the force due to gravity. This work aims to better understand how the compression of air at various depths below the surface of the water contribute to the neutral buoyancy depth, velocity of the object as it rises, …

Increasing The Corrosion Protection Of Aisi 1008 Carbon Steel By Surface Treatment With Unmodified And Benzotriazole Modified Sol-Gel Films, Shane Thomas Kelliher

Williams Honors College, Honors Research Projects

The corrosion performance of sol-gel coated AISI 1008 carbon steel was investigated in 3.5 wt% NaCl solutions of pH 7, 9, and 12 using electrochemical measurements. A corrosion inhibitor, benzotriazole (BTA) was added to the sol-gel mixture and tested as a second, modified sol-gel coating. Sol-gel films adhered evenly to metal samples and were characterized by FTIR spectroscopy. Electrochemical Impedance Spectroscopy (EIS) showed an increase in polarization resistance from blank to sol-gel coated samples (600-18,800,000 ohms). Cyclic polarization (CPP) curves showed positive hysteresis loops for blank and unmodified sol-gel coated samples which increased at high pH following the backward potential …

Quantifying Mafenide Release From 3d Printed Phenylalanine-Coumarin Copolyester Scaffolds, Jacob Seeh

Williams Honors College, Honors Research Projects

This project addressed burn wound healing through controlled release of the antibacterial drug mafenide encapsulated by a copolyster into 3D printed scaffolds. Scaffolds were printed at 25^oC and 0.77-1 bar in a cross-hatch pattern with uniform thickness, distance between parallel layers, and diameter then photo-crosslinked. The number of scaffolds available for testing was limited by the amount of polymer that could be synthesized. A high-performance liquid chromatography method was developed specifically for this experiment and used to determine daily release of mafenide from the scaffold into a 2-mL phosphate buffer solution. During the first 24 hours a large …

Molecular Recognition Of Pet Depolymerization Products And Beta-Cyclodextrin, Thomas Palisin

Williams Honors College, Honors Research Projects

Using molecular recognition techniques to determine the binding constant of the host-guest relationships of the depolymerization products of polyethylene terephthalate (PET) and cyclodextrin species. The main method of data collection used was florescence spectroscopy. Using a titration method and measuring the florescence intensity, a nonlinear regression was used to determine the binding constant.

A Comparison Of Fiber Mat Thickness Measurement Techniques Using Laser Interferometry And Water Displacement, Ryan Seabeck

Williams Honors College, Honors Research Projects

Polymer fiber mats may often be very thin which leads to complications in measuring thickness. The thickness of fiber mats, however, is crucial in understanding their behavior. Thickness affects how well the mat works as a filter as well as the pressure drop across the mat, and herein lies the need for accurate measurement techniques. Currently two of the available techniques for measuring mat thickness are by laser interferometry[1] and by buoyancy force when submerged in water[2]. Instead of measuring the buoyancy force in this experiment, an enclosure intended to measure the thickness via water displacement was …

Chloride Effect In Fly Ash Geopolymer Cement, Evan Dimmick

Williams Honors College, Honors Research Projects

The production of ordinary portland cement (OPC) poses a significant impact on the world's carbon dioxide emissions through the wide global use of concrete. Geopolymer cements (GPC) made from alkali activated fly ash can serve as a replacement to OPCs, reducing the carbon dioxide emissions by as much as 80%. GPCs exhibit adequate or superior mechanical performance to OPCs. The corrosion of carbon steel rebar in concrete occurs largely from chloride ion attack. The focus of this project will be to experimentally determine the coefficient of diffusion for chloride ions in GPCs and OPCs and compare to the corrosion performance …

Exploring Shape-Memory Polymers From Silicone I And 1,10-Decanediol Blends, Kristina Nguyen

Williams Honors College, Honors Research Projects

Shape-memory polymers (SMPs) are polymeric materials that have dual-shape capabilities. These materials can deform to a temporary shape and will recover to their permanent original shape when induced by an external stimulus such as heat. The purpose of this project was to investigate the thermo-mechanical properties and shape-memory behavior of various blends of Silicone I and 1,10-decanediol to determine if a unique blend of these components can be utilized to develop shape memory surface relief patterns.

Careful iterative experiments were used to develop a robust procedure for the fabrication of crosslinked sheets of blends of Silicone I and 1,10-decanediol over …

Utilizing Virtual High-Throughput Screens To Identify Promising Inhibitors Of Complement Factor C1s, Lyndsey Schmucker

Williams Honors College, Honors Research Projects

A large study was conducted to identify possible drug candidates to treat various diseases using computer algorithms, virtual high-throughput screens, and experimental validation of activity. Since the algorithm has the capability to screen millions of compounds, it is beneficial to pharmaceutical development as it allows a larger pool of compounds to be considered that would have otherwise been overlooked. As part of this larger study, this project attempts to identify drug candidates to treat human complement factor C1, a protein which causes tissue damage when underregulated¹. A series of designed experiments validate candidates and confirm the performance of …

Design Of Pigments For Use In “Cool” Coatings, Tyler Laughorn

Williams Honors College, Honors Research Projects

This project was focused on the development and testing of several novel pigments that exhibit high NIR-reflectance and therefore show potential for use in “cool” coatings. A “cool” coating will reflect more solar radiation than other standard coatings, and so a coated structure would require less energy to keep cool. Four sets of pigments were synthesized: Co_1-xMg_xCr₂O₄ (teal), Co_0.25Mg_0.75Cr_2-yAl_yO₄ (blue), Ti_1-x-yNi_xSb_yO₂ (yellow), and Cr_2-xFe_xO₃ (black). NIR and TSR values were then measured …

Filtration Apparatus Design For Oil-Water Separation Using Membranes And Sponges, Alec Jerger

Williams Honors College, Honors Research Projects

It can be difficult to separate water and oil emulsions through traditional filtration. Therefore, investigations of filtering using thermo-responsive (TR) polymers, in this case poly(vinyl methyl ether) (PVME), was conducted. It’s hypothesized that below its lower critical solution temperature (LCST), PVME has an affinity for water while oil substances do not. Above the LCST the opposite will be true. To verify this hypothesis, iterations of filtration designs were created to provide optimum control over the parameters to measure flow. The final optimized experimental apparatus was a Chromaflex glass column which was air tight and controlled all parameters besides fluid flow. …

Effects Of Hofmeister Ions On Solubility And Swelling On Gelatin Hydrogels, Hannah Eldridge

Williams Honors College, Honors Research Projects

Hydrogels are known to be weak and brittle, due to the amounts of water that they hold. Gelatin-based hydrogels specifically are inexpensive and easily accessible, but often have poor physical properties. The goal of my project was to strengthen gelatin-based hydrogels and improve their mechanical properties by forming these hydrogels in different aqueous solutions containing kosmotropic Hofmeister's ions. Prior research has shown that these ions are able to take water away from gelatin-based gels, which forms a tougher hydrogel. The success of this project will be measured by studying the solubility and swelling effects that different Hofmeister ions have on …

Testing The Effectiveness Of Reflective "Cool" Pigments, Ashleigh Carpenter

Williams Honors College, Honors Research Projects

This project is an exploration of reflective "cooling" pigments used in coatings for the exterior of a structure in order to control the temperature inside. The pigments reflect sunlight to reduce the heating effect inside a structure. While the project will include the synthesis and testing of these pigments, the focus will be on the design and construction of an apparatus to test the effectiveness of these pigments. An apparatus will be constructed with a heat source and two structures of identical dimensions. The set-up will allow for the temperature of the inside of the structures to be recorded at …

Zips Precious Plastics: Plastic Extruder, Patrick Cole

Williams Honors College, Honors Research Projects

This project's goal was to design and build an affordable desktop filament extruder that can precisely and consistently extrude filament to a certain tolerance acceptable for 3D printers using wasted printing material. The group is partnering with an on campus organization focusing on engineering applications for sustainable futures. Zips Precious Plastics is a student run design group that intends to bring an innovation space on campus to help educate students about the importance of a closed looped system within plastic manufacturing.

Controlled Crystallization Of Pet Filaments In Additive Manufacturing, Ryan Kordahi

Williams Honors College, Honors Research Projects

Polyethylene terephthalate (PET) appears in daily life in many forms, the most common being disposable soft drink bottling. To deal with the ever-growing quantitity of disposed PET (both in landfills and environment), a waste plan revolving around depolymerization should be implemented. Specifically, the potential of PET depolymerization through aminolysis into useful, low molecular weight monomers will be explored with the end goal of producing a 3D printing filament and analyzing economic feasibility.

Optimization Of E-Textiles For Lactic Acid Detection, Andrew Laboy, Mallory David

Williams Honors College, Honors Research Projects

The overall goal of the project is to develop an e-textile that will be able to determine different characteristics of an athlete's health through multiple sensors. The goal of these sensors is to monitor physiological parameters for health and fitness uses in real time. Building from the existing sodium concentration sensor, these new sensors will detect lactate levels within sweat to monitor instantaneous health which allows customization of workout and overall health regimen.

Evaluating Rubber Aging On Tire Durability: Quantitative Evaluation Of Rubber Aging, Brian Auffenberg

Williams Honors College, Honors Research Projects

Rubber is considered one of the most important polymers in the world due to its variety of uses. There are many different conditions that can affect the useful life of rubber. The purpose of this research was to determine how the mechanical loading on the rubber may affect the aging of the rubber. The scope of the project was to focus on the rubber used for tire production. The research was limited to focusing only on rubber supplied by industry mentors which was styrene-butadiene rubber. By varying the length of time for testing as well as the temperature of the …

A Foundational Approach To Extrusion And Compounding, David Frankart

Williams Honors College, Honors Research Projects

With a history of nearly 200 years, polymer processing and compounding is constantly changing to fit the material science needs of the era. Exposure of undergraduate students to the technology and practices used in industry today in a lab setting would create new opportunities for experiential learning and growth. The objective was to set up a 0.75”, 25 L/D Thermo Haake single screw extruder for lab use and run trials of material in a single screw extruder to set up a basis for experiments. Trials were run of co-polyester resin through a single screw extruder with carbon fiber additives varying …

Methods For Film Coating Electrospun Fibers, Kristopher Dejean

Williams Honors College, Honors Research Projects

Electrospinning uses high voltages to form polymer nanofiber membranes. These membranes have potential for use in filtration, tissue engineering, drug delivery, and catalysis. The nonwoven fiber mat is malleable but has a low tensile strength compared to a solid film of the same polymer. Joining the fibers with a thin film is desired to balance the strength and flexibility. Three methods of producing a film on fiber membrane were tested. The techniques are spraying then melting, spin coating, and dip coating. Electrospinning setup conditions, solvent ratios, damage to fibers, and spin coating speeds were determined. Research was abruptly stopped and …

Effects Of Crosslinking Conditions On Biofouling Of Polymer Substrates With A Hydrogel Layer, Laura Davila

Williams Honors College, Honors Research Projects

The introduction of a hydrogel coating to a surface has been looked at for different benefits. Certain hydrogels offer antifouling properties that are beneficial to different applications like medical components. Previous attempts (2) (3)have been done to introduce a hydrogel surface to plastic substrates. One of them is to use grafting brushes which works properly but it is not sufficient since the layer is too thin and therefore can be damaged. The second method have a bulkier coating without crosslinking. Opposite to grafting brushes this method has too thick of a layer. Additionally, there is no crosslink therefore the coating …

Optimization And Validation Of The Neurolux Wireless Optoelectronics System For Optogenetics, Karis Courey, Su Hyun Lee Ph.D., Adam Smith Ph.D., Nicholas Cilz Ph.D., Sarah K. Williams Avram Ph.D., Adi Cymerblit-Sabba Ph.D., June Song, Nicholas Leipzig Ph.D., W. Scott Young M.D., Ph.D.

Williams Honors College, Honors Research Projects

Utilizing light and genetic engineering, optogenetics permits the manipulation of events within cells via light using the light-sensitive properties of single-component microbial opsins. Microbial opsins are activated by a light source, such as lasers, light-emitting diodes, and incandescent sources that deliver light to the region of interest either directly or indirectly, such as through fiberoptics. In classical in vivo optogenetics, the wiring of optic fibers necessitates tethering of animals by the optic fiber to the light source. The novel NeuroLux wireless optoelectronic system for optogenetics circumvents issues pertaining to classical optogenetics by utilizing near-field power transfer via magnetic coil antennae …

Methods For Film Coating Electrospun Fibers, Kristopher Dejean

Williams Honors College, Honors Research Projects

Electrospinning uses high voltages to form polymer nanofiber membranes. These membranes have potential for use in filtration, tissue engineering, drug delivery, and catalysis. The nonwoven fiber mat is malleable but has a low tensile strength compared to a solid film of the same polymer. Joining the fibers with a thin film is desired to balance the strength and flexibility. Three methods of producing a film on fiber membrane were tested. The techniques are spraying then melting, spin coating, and dip coating. Electrospinning setup conditions, solvent ratios, damage to fibers, and spin coating speeds were determined. Research was abruptly stopped and …

Understanding Effects Of Engineering Outreach On Elementary Students, Thomas Cobb

Williams Honors College, Honors Research Projects

Currently, there is a desire to increase engineering understanding held by elementary students. As such, there needs to be a way to stimulate not only engineering, but other science, technology, engineering, and mathematics (STEM) topics in a young student’s lifestyle. One way to emphasize the importance of STEM while also showing how fun it can be is through different hands on activities led by individuals partaking in undergraduate studies or the industry. While having the students participate in the activities, it is important to understand what the students are learning and how the activity overall is viewed. With the help …

Improving The Delivered Specific Impulse Of Composite Rocket Propellant Through Alteration Of Chemical Composition: Methodology And Parameters For Characterization Of Propellant And Validation Of Simulation Software Common To The Amateur Rocketry Community, Isaac O'Brien, Austin Ryan

Williams Honors College, Honors Research Projects

In this study, two solid composite rocket propellants were designed utilizing ProPEP, a rocket propellant formulation software common in the amateur and hobby rocketry communities. The two propellants were designed to optimize specific impulse relative to a literature propellant designed by 1020 Research Labs. The literature propellant was also tested in order to validate the design of experiment as well as the mixing and testing procedures. All three propellants, which includes the literature propellant RCS-P, and the two novel propellants AKR-P1 and AKR-P2 were characterized with static tests. The results of the static tests provide data on propellant performance and …

Effects Of Micro-Features On Cell Detachment From Poly(N-Isopropylacrylamide) Coated Polydimethylsiloxane Membranes, Luke Webel

Williams Honors College, Honors Research Projects

The tested hypothesis was that features on polydimethylsiloxane (PDMS) surfaces coated with a poly(N-isopropylacrylamide)/aminopropyltriethoxysilane or pNIPAAM/APTES thin film would accelerate cell detachment than the film coated on a unfeatured surface. This project tested samples with features generated by molds, wrinkling, and sandpaper roughened substrates. Surface feature generation methods were limited to mechanical means, and characterized by microscopy and strain rates. 50/50 mixtures of 1.5 wt.% pNIPAAM/ APTES were used to coat thin films (30-40 nm) on PDMS membranes by spin-coating, and the coated membranes were thermally annealed to chemically graft pNIPAAm/APTES on the membrane and their thermo-responsive property was assessed …

Increasing Mechanical Properties Of A Double Network Hydrogel From Polyacrylamide And Agar With Methylenebisacrylamide As A Photocrosslinker, Madelyn Jeske

Williams Honors College, Honors Research Projects

Double Network hydrogels are three dimensional networks of a soft, mechanically tough material that have been used for drug delivery, agriculture, adhesives, and other widely applicable uses. Using the one-pot method, a single hydrogel can be produced in 3 hours as opposed to the once demonstrated three days. It has been found that with a first, physically cross linked network and a second, chemically cross linked, hybrid double network hydrogels exhibit high mechanical properties and are freeshapeable. Agar is a thermoreversible organic molecule with a triple helix structure that provides an excellent first network that organizes into aggregate bundles once …