Chemical Engineering Commons^™

Environmentally Friendly Alternates To Chemlok 233 Adhesive Cement, Madeline M. Busch

Williams Honors College, Honors Research Projects

The purpose of this project was to determine and qualify suitable, environmentally friendly replacement(s) for the current Chemlok 233 adhesive cement used by UTC Aerospace. Chemlok 233 was discontinued by the manufacturer based on the availability of a hazardous solvent (Trichloroethylene – TCE). The Chemlok 233 Control and four Experimental alternates with similar properties were lab tested for adhesion strength in various UTC proprietary cement specifications. The specifications modeled Chemlok’s uses in the construction of pneumatic de-icers. Chemlok 2332 was selected for use in Cement A, and Chemlok 402 was chosen for use in Cement B based on their highest …

Correlation Of Electrospun Polyvinylpyrrolidone Fiber Mat Thickness With Basis Weight, Fiber Diameter, Pore Size Distribution, And Air Permeability, Leah Mcpherson

Williams Honors College, Honors Research Projects

This project developed correlations between electrospun polyvinylpyrrolidone fiber mat thickness, basis weight, fiber diameter, pore size, and air permeability. The hypotheses were thinner fibers produce thicker mats, pore size decreases with fiber diameter, pore size and permeability decrease as basis weight increases. Project results could be used for modeling or quality control purposes.

Fiber diameter distributions were analyzed using a Scanning Electron Microscope and FibraQuant 1.3 software. Four conditions were chosen for further study: 0.284 ± 0.104 µm, 0.379 ± 0.128 µm, 0.520 ± 0.138 µm, and 0.733 ± 0.177 µm. Lower PVP concentrations produced thinner fibers.

Sample thickness (nm) …

Vanadium Redox Flow Batteries: Design And Experimentation, Matthew George

Williams Honors College, Honors Research Projects

Vanadium flow batteries (VFB) are a type of battery that has potential as a grid-scale energy storage solution. An original design for a lab-scale VFB is presented herein, along with a procedure for electrolyte preparation from V₂O₅ using oxalic acid. The flow cell is constructed from Delrin, Teflon, Kynar, Santoprene, Nafion, graphite plate, and porous carbon. Two diaphragm pumps along with polyethylene, PVC, and Santoprene tubing are used. The active area is 58 cm². The battery was charged using a DC power supply at a constant current of 4 A with corresponding initial voltage of …

Effects Of Corrosion Inhibitor On The Corrosion Behavior Of Low Carbon Steel In Co2 Environment, Michael Harris

Williams Honors College, Honors Research Projects

The effectiveness of Benzalkonium chloride (C14) as a corrosion inhibitor for mild steel in an aqueous CO₂ environment was studied for dual use. It is a known biocide and currently untested corrosion inhibitor. Potentiodynamic polarization was used to determine the anodic and cathodic reaction kinetics through analysis of the potentiodynamic curves and the corrosion current densities. Electrochemical impedance spectroscopy (EIS) was utilized to analyze the surface characteristics through analysis of the Nyquist and Bode plots. C1010 and C1018 mild steel were tested in a 200mL jacketed Gamery cell, and purged with CO₂ (99.9%). Temperature effects were studied and …

Evaluation Of Epoxy Coatings For Protecting Aluminum Alloy 2024 From Corrosion Caused By Aspergillus Niger, Kamshat Dukenbaeva

Williams Honors College, Honors Research Projects

The aim of this study was to assess the potentials of using epoxy coatings for the prevention of fungus-induced corrosion. The metal specimen of interest was the aluminum alloy AA 2024-T3. The main intent was to evaluate the behavior of the organic acid producing fungus, Aspergillus niger (A. niger), towards the epoxy-coated aluminum. Two different types of epoxy coatings were used: a two-part resin and a commercially-available Rust-Oleum Specialty Appliance Epoxy. Due to challenges encountered throughout the length of the project and time constraints, limited quantitative data was obtained. However, from optical and visual data it can be concluded that …

Controlled Humidity Chambers To Maintain Red Roses’ Freshness And Improve Their Shelf Life, Rima Vasudevan

Williams Honors College, Honors Research Projects

Floriculture is the third largest agricultural crop in the United States of America. Flowers are usually transported in pots of mud or with the roots still submerged in water to increase their shelf life and ensure freshness during long hours of transport. This not only increases the weight of the transport materials but also makes the process expensive.

The research conducted provides the first stages of an alternative packaging material that can lower the weight of transport materials and maintain the freshness of the flowers. The experiments conducted in this work support the hypothesis that using controlled high (>60%) …

The Influence Of Light On The Electrochemical Characteristics Of Pure Aluminum, Hongbo M. Cong

Williams Honors College, Honors Research Projects

The objective of this work was to study the influence of light (wave length ~ 460 nm) on the electrochemical characteristics of pure aluminum. The open circuit potential (OCP) measurements, potentiostatic polarization, cyclic potentiodynamic polarization and Zero Resistance Ammetry (ZRA) were performed in 0.1 M NaCl solution. It was observed that the incident light shifted the OCP in the noble direction by 100 mV. Furthermore, ZRA was performed to measure the galvanic current between illuminated and non-illuminated aluminum electrodes. Cyclic potentiodynamic polarization tests revealed the influence of light on the pitting potential, passive current density, corrosion current density, and repassivation …

Design Of Rubber Extraction Process From Tks Dandelion, Trevor A. Cody

Williams Honors College, Honors Research Projects

A design was developed for a controlled environment agriculture 3D greenhouse to grow and harvest TKS dandelions, as well as a processing plant to extract natural rubber and inulin from the roots. The design capacity was scaled for both pilot- and full-scale production: 100 and 100,000 tonnes of natural rubber per year, respectively. The byproducts of the process were dandelion greens, inulin, cellulose, and glucose; all of these except for cellulose were able to be valorized. The greenhouse was designed based on existing 3D hydroponic growing environments, and the extraction process was designed based on the original TKS dandelion extraction …

Design Of Natural Rubber Extraction From Tks Dandelion, Jehad S. Alrawajfeh, Trevor Cody, Jason Pogozelski

Williams Honors College, Honors Research Projects

A design was developed for a controlled environment agriculture 3D greenhouse to grow and harvest TKS dandelions, as well as a processing plant to extract natural rubber and inulin from the roots. The design capacity was scaled for both pilot- and full-scale production: 100 and 100,000 tonnes of natural rubber per year, respectively. The byproducts of the process were dandelion greens, inulin, cellulose, and glucose; all of these except for cellulose were able to be valorized. The greenhouse was designed based on existing 3D hydroponic growing environments, and the extraction process was designed based on the original TKS dandelion extraction …

Role Of Salt On Coating Failure, Kyle Krause

Williams Honors College, Honors Research Projects

It is important to understand the role of salt in the coating failure because it may influence the coating degradation mechanism that is related to coating performance. This project will study the role of salt on two types of organic coatings under two different immersion environment. The environment selected was 3.5% by weight sodium chloride solution and deionized (DI) water. The two coatings were Neorez 1080 (a waterborne polyurethane) and Joncryl 587-AC (a solvent borne polyurethane). Each coating was tested in each environment using electrochemical impedance spectroscopy (EIS) measurement which presented a total of four data sets. The equivalent circuit …

Characterization Of Polyurethane For Use As Substrate In Nanofiber Sensor For Biomedical Applications, Megan Theaker

Williams Honors College, Honors Research Projects

The purpose of this project is to begin to determine properties of polymer nanocomposites that make a suitable substrate for nanofiber sensors. In this work, sensitivity of a sodium ion selective sensor constructed with polyurethane was used as a benchmark for comparison with sensors constructed with nylon-6. The sensors were characterized using contact angle and chronoamperometry. Using an ANOVA analysis, the results showed that the multi-walled carbon nanotube type was a significant factor on sensor response both with and without additional functionalization of the polymer by calixarene. The weight percentage of polyurethane in the electrospinning solution was also statistically significant …

Stability And Retention Enhancement Of Low Fouling Polystyrene Sulfonic Acid (Pss) And Polyethylene Glycol (Peg) Blend Films With Silane Coupling Agents, Sean Stybel

Williams Honors College, Honors Research Projects

The goal of this research project was to apply silane coupling agents for enhanced stability and retention of a low fouling polymeric coating to an inorganic substrate. A blend of polystyrene sulfonic acid (PSS) and polyethylene glycol (PEG) was crosslinked in order to create a low fouling film. The film was prepared by spin coating a PSS-PEG solution on an inorganic substrate coated with a layer of a silane coupling agent (3-aminopropyltriethoxysilane, APTES, solution), followed by thermal curing. The research was limited to less than one year and only used lab equipment available at the University of Akron. Stability and …

Platinum-Rhodium Alloy Electrocatalyst Activities In The Methanol Oxidation Reaction, William R. Sandorf

Williams Honors College, Honors Research Projects

This study evaluates the electrochemical activity of several compositions of platinum-rhodium alloys on carbon support to identify potential replacements for the expensive platinum electrocatalysts currently used in direct methanol fuel cells (DMFCs). The electrochemical active surface areas (ECSAs) of each sample were determined using cyclic voltammetry (CV) in a 0.5 M H₂SO₄ solution to normalize CV currents generated in the methanol oxidation reaction (MOR). The activity of five compositions was tested; Pt₃Rh, Pt₂Rh, PtRh, Pt₂Rh, and Pt₃Rh. 100 mg of each catalyst was synthesized at 10% by weight platinum …

Polarized Elastic Nanofiber Tubular Mat, Elizabeth Moore

Williams Honors College, Honors Research Projects

Abstract

The scope of this project is to find the optimal parameters to polarize a nanofiber membrane in a tubular geometry as spun on a metal spring. Several different recipes were tested for electrospinning and polarization. Some recipes proved unable to be electrospun. A polymer solution with 12 weight percent resulted in good fiber formation. The results from the polarization attempts proved inconclusive as the electrostatic surface charge did not appear to change. The readings were taken with an electrostatic field meter. As a future experiment a new measurement technique with a Faraday cage will be utilized.

Chemical Modification Of Crumb Rubber To Increase Its Bonding With Concrete, Mary T. Mccannon, Kendall J. Sweitzer

Williams Honors College, Honors Research Projects

The hydrophilicity of crumb rubber was increased with wet chemical modification and added to concrete to increase its adhesion with concrete, consequently the compressive strength relative to that of concrete with untreated rubber. Other modification methods were tested on crumb rubber and rubber sheets to yield an increase in hydrophilicity. Certain tests were less reliable for powder testing or tedious and time consuming and concrete materials and rubber may not be homogeneous.

For wet chemical modification, several approaches were attempted. First, crumb rubber was soaked in 5% sodium hydroxide, 5% potassium permanganate and saturated sodium bisulfite, tested for hydrophilicity using …

Titanium Nanoparticles Synthesized Via Hydrothermal Reaction, Kyle W. Hodge

Williams Honors College, Honors Research Projects

The main goal of this project was to determine if increasing the time and temperature of a hydrothermally reacted titanium nanotube would increase the size of the nanotubes. Five experiments were conducted while varying the time and temperature of the reaction: 120°C for 24 hours, 120°C for 48 hours, 150°C for 24 hours, 180°C for 24 hours, and 180°C for 48 hours. Following the synthesis of all of these samples x-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive spectroscopy (EDS) analyses were performed. The XRD analysis revealed anatase titanium nanoparticles formed in the 120°C and 150°C samples, this could …

Protein Release Study Using Heparin Modified Methacrylamide Chitosan Hydrogels, Dakotah G. Cox

Williams Honors College, Honors Research Projects

This study was performed to improve the release of proteins from hydrogels in order to increase their effectiveness in treating spinal cord injuries. Heparin, which has the ability to bind to proteins and slow their release, underwent methacrylation, was added to prepared methacrylamide chitosan (MAC) solutions with a model protein (SDF-1α) and photopolymerized to create MAC-heparin hydrogels. Varying weight percentages of methacrylated heparin were tested in order to determine the optimal amount needed to improve the release profile. The pure MAC hydrogels and gels with 10 wt% heparin had a rapid release of the SDF-1α (>23% and >29%, respectively, …

Process Control Laboratory Skid Refurbishment, Danny Crowder

Williams Honors College, Honors Research Projects

This project evaluates a salvaged process control skid for potential refurbishment and educational re-use. In-lab work evaluated the existing skid. Several process control elements have been recommended for replacement, including the process tank (due to corrosion), the pressure transmitter (operability/corrosion), the flow meters (mechanical) and the control system (age). The control valves, temperature elements and transmitters, pump, holding tanks, and the electrical heat exchanger should be salvaged. An I/P converter and pressure relief valve should be added to the pneumatic feed. Enclosing of all electrical components should be prioritized. An electrical schematic for a new control system should be implemented. …

Corrosion Resistance Of Silane Coatings On Aluminum And Magnesium Alloys, John Demopoulos

Williams Honors College, Honors Research Projects

The purpose of this project was to increase the corrosion resistance of aluminum and magnesium alloys by coating the coupons with a silane on the surface. Four different silanes: 3-aminopropyltriethoxysilane (APTES), Bis(triethoxysilylpropyl)amine (Bis), (Heptadecafluoro-1,1,2,2-tetrahydrodecyl)trichlorosilane (FTS), and (Heptadecafluoro-1,1,2,2-tetrahydrodecyl)triethoxysilane (non Cl FTS) will be used and compared to see which silane would give the best corrosion resistance. Each silane solution was coated on the coupons by using a solution method in which the coupon was submerged for 24 hours and then thermally cured for another 24 hours. Once the coating was applied, the water contact angle and the thickness of the coating …

Selective, Catalytic Decomposition Of Hydrazine, Benjamin A. Kitson, Shirin N. Oliaee

Williams Honors College, Honors Research Projects

The selective, catalytic decomposition of hydrazine has been investigated using a 1 wt% Pt-Ni(OH)₂ catalyst system quantitatively studied by changing the following parameters; reaction solution alkalinity, temperature, hydrazine concentration, catalyst selectivity, catalyst stability, and catalyst durability. Using sodium hydroxide (NaOH), the best alkalinity was found to be 1 M NaOH. The optimal temperature was found to be 50 °C for complete hydrazine conversion. A hydrazine concentration of 0.1 M produced the most effective reaction. The catalyst was found to be completely selective in hydrogen and nitrogen production with no ammonia formation. The catalyst activity decreased by 15% after 8 …

The Effect Of Drying On The Release Of Small Hydrophilic Molecular Drugs From Polyelectrolyte Complex Beads, Dounsavanh Letdara

Williams Honors College, Honors Research Projects

The effects of bead composition and dryness on the release rate of small molecules, like a drug or dye, from polyelectrolyte complex (PEC) beads were studied. Release studies were performed on dried and not dried beads prepared using different PEC to drug ratios. The beads were dried for two hours, which allowed them to reach a constant weight. The beads were loaded with a dye, so their release could be detected through the visible light regime. A plate reader was used to determine the absorbance of a sample, and then the amount of dye released was determined. The data presented …

Microbiologically Influenced Corrosion: Rhamnolipid Effects, Andrea M. Wildroudt

Williams Honors College, Honors Research Projects

The purpose of this experiment was to identify if a rhamnolipid could inhibit the growth of a biofilm on carbon steel coupons and result in less corrosion activity. This type of research impacts various industries (with one of the largest being the oil and gas industry). Multiple systems with varying concentrations of the rhamnolipid were created to determine, if any, the optimum concentration to inhibit biofilm growth. The systems were created and exposed to optimum physio-chemical environments to promote SRB induced corrosion. Coupons were immersed for 28 days. Seven systems were created with varying rhamnolipid concentrations; to ensure accurate results, …

Calcium Alginate Microbead Production Via An Air Assisted Shearing Process, Ryan Loftus

Williams Honors College, Honors Research Projects

The purpose of this project was to model the size of calcium alginate microbeads produced by extruding a solution of 1.5 wt.% alginate from a syringe and needle with air shear generated from a pneumatic line flowing in an annular tube around the extrusion needle. The air shear would create microdroplets that would fall into a solution of 2 wt.% calcium chloride in water, crosslinking the droplets into beads. These microbeads can be used in drug dispersion applications or in encapsulation of cells throughout the body due to their biocompatibility. The goal was to create uniform beads that ranged from …

Separation Of Water From Ulsd Using Superhydrophobic Ps Nanofiber Mats, Alisa G. Webel

Williams Honors College, Honors Research Projects

Superhydrophobic polystyrene nanofiber membranes have potential to separate micron scale water droplets from organic due to their hydrophobicity and small pore openings. Polystyrene nanofibers were electrospun into flat sheets and cylindrical filter membranes. The fibers were crosslinked to increase strength and reduce solubility in diesel fuel. The filters were tested and the filtration efficiency was compared to their non-crosslinked counterparts. The optimal electrospinning conditions to create superhydrophobic nanofibers were found to be 20 wt. % PS fibers at 1 mL/hr. under a current of 20kV and at a distance of 20 cm away from the ground. It was found that …

Construction Of Polyurethane Fabric Nanocomposites For Use In Resistance Temperature Detectors-Effect Of Polyurethane Concentration, Multi-Walled Carbon Nanotubes, And Oxidant, Jordan M. Shaffer

Williams Honors College, Honors Research Projects

Current resistance temperature detectors (RTDs) are rigid and create pressure points when used in contact with the human body. The current RTDs can also not be used in confined areas like the inside of a prosthetic. The research done for this paper explores the possibility of creating a soft fabric like RTD that can accurately measure temperature. This RTD could be used in medical devices, be placed in prosthetic legs, and be worn for a long period of time creating no discomfort for the user. Polyurethane scaffolds were created through an electrospinning process and multiwalled carbon nanotubes were adhered to …

Investigation Of Degradation Of Amine Sorbent, Elijah Arendt

Williams Honors College, Honors Research Projects

The purpose of this study is to investigate the performance of amine-grafted sorbents, specifically when they are degraded at 120°C. This study varied the amine source and the amount of it in the sorbent. The additive type and the amount of it was also manipulated. The performance of sorbents is characterized by CO₂ capture capacity, which is the amount (in mmol) of CO₂ captured per gram of sorbent at 40°C. The best performing sorbents are ones that maintain their CO₂ capture capacity after degradation. When the amount of additive was manipulated, the sorbents containing 2% b.w. and …

Passivation And Potential Fluctuation Of Az31b Alloy In Alkaline Environments, Ana C. Bacco

Williams Honors College, Honors Research Projects

Magnesium (Mg) alloys are used in many industries because of their distinctive properties, but their high chemical reactivity and poor oxide film protection make them inferior. This project focused on investigating the effects of secondary phases and intermetallic particles (IMPs) on the corrosion behavior of AZ31B Mg alloy. The test solution was chloride free NaOH with varying pH levels between 10-14, as well as testing under deaerated conditions. The open circuit potential (OCP) measurements using AZ31B in static NaOH solutions showed potential fluctuation between approximately -1.6 V_SCE (active state) and -0.4 V_SCE (passive state) during the 24-h immersion. …

Prediction Of Vapor/Liquid Equilibrium Behavior From Quantum Mechanical Data, Marshall J. Gnap

Williams Honors College, Honors Research Projects

MOSCED (Modified Separation of Cohesive Energy Density) is a particularly attractive model for activity coefficients because it offers intuitive insights into how to tune solvent-solute interactions to achieve optimized formulations. Unfortunately, only 133 compounds have been characterized with the MOSCED method. Furthermore, there is no convenient method for extending MOSCED predictions to new compounds. The hypothesis of the present research is that the surface charge density of a molecule, once normalized over the molecule surface area, provided graphically by a σ-profile from density functional theory (DFT) computations, can be used to estimate the parameters used in the MOSCED model. DFT …

Stress Corrosion Cracking Evaluation Of Carbon Steel In Biodiesel And The Effect Of Ultrasonic Nanocrystal Surface Modification (Unsm) On 304 Stainless Steel, Josh Geyer

Williams Honors College, Honors Research Projects

The project that was performed was stress corrosion cracking (SSC) of carbon steel in biodiesel, petroleum diesel and a mixture. The project also included the effect of Ultrasonic Nanocrystal Surface Modification (UNSM) on 304 stainless steel. It included the assembly of a slow strain rate (SSR) machine and carrying out testing using the SSR machine. The assembly of the machine will require purchasing and building a stand to house the electrical equipment which includes the computer, actuator control panel and the actuator power supply. The assembly will also include designing and purchasing the connections to connect the actuator to the …

Thermal Responsive Release Of A Model Drug, Rhoadmine B, From Alginate Bead System, Heather F. Fairbairn Miss

Williams Honors College, Honors Research Projects

Smart drug delivery systems have garnered increased interest in the biomedical community during recent years. Investigation into thermal, pH, and light responsive delivery systems allows for targeted drug release systems to be developed. For this project, thermal responsive release behavior was investigated for the purpose of tuning release systems to achieve 60% release in a specified time by varying the content of thermal responsive polymer. To investigate this, the release profile of a model small hydrophilic drug (rhodamine B) from polymeric alginate beads that have been modified by the addition of thermal responsive poly(N-isopropylacrylamide) (PNIPAAm). It was determined that when …