Chemical Engineering Commons^™

The Effect Of An Electrical Corona Discharge Upon The Reaction Of So2 To So3 In Low Concentration So2 - Air Mixtures, Edward James Malarkey

Theses

An investigation of a pilot plant electrical dust precipitator was conducted to determine its ozone generating characteristics in air as well as the ability of the ozone formed to convert gaseous SO₂ to particulate SO₃. It was anticipated that in addition to the known primary particulate dust and mist removal function of a precipitator, a secondary gaseous removal facility was inherent in its operation.

Ozone formation quantities were determined at varied air flow and electrical power input levels to the precipitator. Maximum ozone generation was 0.02 pounds per hour at an energy input level of 113 KW-HR …

An Investigation Of The Mechanism Controlling The Co-Deposition Of Aluminas With Copper During Electrodeposition Of Copper, James Edward Hoffmann

Theses

Experimental work was undertaken to determine the mechanism controlling the co-deposition of aluminas with copper during electrode-position of copper. The aluminas were present in the copper plating electrolytes as an insoluble disperse phase.

Three possible mechanisms for co-deposition of aluminas were studied, They were mechanical inclusion, electrophoretic deposition, and adsorption.

The results of experimental studies established that mechanical inclusion was not a significant factor in the mechanism controlling co-deposition of aluminas with copper.

Theoretical considerations of the compositions of the copper plating electrolytes indicated that co-deposition of aluminas by an electrophoretic mechanism was highly unlikely. The conclusions arrived at by …

Electrolytic Polishing Of Copper And Nickel Silver, Halle Abrams

Theses

To facilitate the study of surface conditions on ultrasonic weldability, electrolytic polishing was used to obtain four types of surfaces on copper and nickel silver (alloy D). A500 orthophosphoric acid bath was used, and the necessary operating conditions to obtain these surfaces were established. In accordance with current electrolytic polishing theory, the existence of the anode viscous layer and anode surface film was observed, and their role in the polishing process is discussed. By means of metallurgical techniques and surface profile measurements, it is shown that the four types of surfaces are significantly different, and good reproducibility of these surfaces …

Fugacity Coefficients Of Gases In Binary Mixtures, David Albin Olson

Theses

A proposed, method of Joffe for determining fugacity coefficients of gases In binary mixtures is presented. The method is evaluated by calculating 320 pairs of fugacity coefficients and comparing the results with experimental data and with values calculated by the method of Pitzer.

Joffe derived the expression for fugacity coefficients by employing the technique of Gamson and Watson. The expression is based on the three-parameter corresponding states principle as previously presented by Pitzer and a proposed definition of the pseudocritical properties.

The method of Pitzer and the proposed method of Joffe both require the same data.

This study is based …

Application Of Radioactive Tracers In The Study Of Diffusional Phenomena, Rodolfo Cilento

Theses

The study of mass transfer of a solute through a solvent can be greatly facilitated by the use of radioactive tracers.

This experiment was developed to demonstrate that by using radioactive tracers very small quantities of matter that would be very difficult to test chemically, can not only be tested but easily followed without disturbing the apparatus in which the diffusion is taking place.

Oleic Acid tagged with radioactive iodine (I¹³¹) was diffused through hexane at constant temperature in a glass column, one inch in diameter and thirty-six inches long.

The diffusion of Oleic Acid was followed by …

Interphase Gas-Liquid Mass Transfer Study In A Horizontal Channel, Bruce R. Marx

Theses

The rate of transfer of hydrogen sulfide and of carbon dioxide from an atmosphere of the gas saturated with water to a flowing stream of water in a horizontal channel was investigated over a range of water flow velocities and absolute pressures.

Mathematical models describing the system in terms of the penetration and boundary layer theories were inadequate when used to calculate the diffusivity of each gas in water at various conditions. The results of the hydrogen sulfide-water system study shows a relationship between the diffusivity, the interfacial concentration and the liquid flow rate. The calculated diffusivity of the carbon …

Gas Phase Fugacity Coefficients, Harvey Joel Klee

Theses

A method is presented for calculation of fugacity coefficients in gas mixtures. This work is based on a recent paper by Leland, Gamson, and Chappelear, wherein they presented a new method for evaluation of ideal K values. The information required for the method presented here includes pure component physical properties, and generalized tables or equations for compressibility factors, fugacity coefficients, and real gas enthalpy departure terms. Pseudo-critical temperatures and pressures for the mixture are calculated using the expressions presented by Leland and Mueller.

Five different binary systems consisting of paraffin hydro-carbon and CO₂ mixtures containing 318 separate points were …

Decomposition Of Diacetone Alcohol In Packed Beds Of Ion Exchange Resins, Arthur Donald Lahr, Rafael Juan Puente-Duany

Theses

A study was made of the rate of decomposition of diacetone alcohol by anion exchange resins in a packed bed under adiabatic and isothermal conditions. Two different resins were compared: a conventional type gel structure resin, Amberlite IRA-400, and a newly marketed maorore-ticular resin, Amberlyst A-26.

In a substrate with low water content, the rate of decomposition of diacetone alcohol by Amberlite IRA-400 vas controlled by intraparticle diffusion. This vas due to shrinkage of the polymer chain matrix of the resin. When dry diacetone alcohol feed was introduced the amount of decomposition was not measurable.

It was found that the …

Thermodynamic Properties Of Perfluoropropane, Frank Fang

Theses

The thermodynamic properties of perfluoropropane (octafluoropropane) have been determined by the author for the saturated region from -100°C to the critical temperature, 71°C. Properties in the superheated region were likewise determined by the author for temperatures from -35°C to 300°C and over a pressure range from 1 atmosphere to 40 atmospheres. Enthalpies, entropies, densities, and specific volumes are reported for both vapor and liquid phases where applicable. The datum point used in these calculations is based on a zero value for vapor enthalpy and vapor entropy at -100°C and 0.0183 atmospheres.

Constants used in the Benedict-Webb-Rubin equation of state were …

An Oxidation Of Para-Nitrotoluene, Albert Edward Meisinger

Theses

The original purpose of this paper was to investigate the reaction kinetics of the air oxidation of para-nitro-toluene (PNT) to para-nitrobenzoic acid (PNBA). The reaction was to be carried out at atmospheric pressure and at temperatures between 100 and 175° C, and in the presence of an oxidation catalyst. However the main problem became one of trying to find a catalyst that would work at these conditions. The catalysts used were nickel acetate, cobaltous acetate, manganous acetate and manganese naphthenate. Hydrogen peroxide was tried as an accelerator for the reaction. None of these worked since no yield greater than 0.01% …

Effect Of Temperature On Rate Of Absorption Of Ammonia By Water In Packed Tower, Chhotu B. Patel

Theses

Measurements of the rate of absorption of ammonia in water have been made using a 4-inch diameter Lucite column With porcelain Raschig rings packed to a height of 3 feet, Tests were made with water rates of 462 and 695 lbs./ hr-ft² and a constant gas rate of 130 lbs/hr-ft² with liquid temperature verying from 72° F. to 110° F.

At constant liquid and gas rate, the mass transfer coefficient, Κ_Ga, decreases with increasing liquid temperature and in represented by straight lines on plot of Κ_Ga versus temperature. The variation of Κ_Ga …

Esterification Of Oleic Acid, Niranjan Muljibhai Patel

Theses

The purpose of this paper is to determine the effects of catalyst concentrations and temperatures on the rate of reaction and energy of activation in the reaction system of oleic acid and oleyl alcohol. It is suggested by Flory^2,3 that the p-toluene-sulfonic acid catalyzed esterification reactions follow a second order mechanism. The p-toluene-sulfonic acid is used in the present work.

Two different catalyst concentrations were used at two different temperatures. The uncatalyzed reaction at the same temperatures was also studied. The specific rate constants are calculated and from that, the energy of activations are calculated using the Arrhenius equation. …

Diffusion Of Single And Multicomponent Solutes From Capillaries, Oleh S. Sklepkowycz

Theses

The purpose of this investigation was to determine the diffusion coefficients of several single and multi-component solutes, and to establish the relations between the diffusivity, the solute composition) and the diffusion rate. Such information pertinent to the extraction and leaching operations, can not be found in literature.

The procedure developed by Piret, Wbel, and Armstrong (25), involving observation of the extraction rate of two-phase mixtures from straight capillaries, was adopted and verified on a known sodium chloride-water system.

In the course of the experimental work diffusion coefficients more determined for ursolic acid, palmitic acid, and tripalmitin in methyl isobutyl ketone. …

The Reaction Of Urea With Primary Alkyl Bromides, Ronald Lewis Stabile

Theses

The reactions between urea and the primary alkyl bromides from 1-bromobutane to 1-bromooctane were investigated. The effect of concentration, temperature, and solvents on the yield was determined. Second order reaction rate constants at temperature of 80°, 100°, and 132°C were calculated from the data for yield. The yield is defined as the percent of bromine from the alkyl bromide titrated as bromide ion.

The results indicate that the reactions of the primary alkyl bromides with urea are similar; the reaction being of the second order and the ex. tent of reaction being approximately the same for each alkyl bromide for …

Amination Of Alkyl Halides, Frank Joseph Stulb

Theses

The possibility of aminating alkyl halides with urea was the prime interest of the research undertaken in this thesis. Alkyl halides and urea react only to a slight degree. However the reaction is rapid when dimethylformamide is used as a solvent.

In working with compounds containing halogen on the aromatic ring we always found the halogen to be replaced by the amino group. With alkyl halides, however, this was not so. In the case of the reaction between an alkyl halide and urea in a solvent, a compound of composition close to that of a di-alkylurea was isolated and the …

Salt Effects In Liquid-Liquid Equilibria, Edwin Otto Eisen

Dissertations

The effect of lithium chloride, sodium chloride and potassium chloride on the distribution of acetic acid, propionic acid and butyric acid between benzene and water at 25° C has been studied. The method of Hand, which has previously been used to correlate tie line data in salt-free ternary systems, has now been successfully employed to correlate distribution data for quaternary systems containing salt.

The slope and intercept of the Hand equations have been expressed as linear functions of the salt concentration in each system studied. Equations for slope and intercept possessing high statistical significance have been formulated using a linear …

The Virial Equation Of State Based On Critical Constants, Ghanshyam R. Patel

Theses

Results obtained from the Epstein equation of state¹⁵ i.e. equation (8), which is theoretically valid up to the critical density, are compared with the experimental values of the compressibility factor. The calculated values of compressibility factor or ethylene, ethane, propane, and n-butane were obtained using two methods of evaluation for the second and third virial coefficients. In addition, using these two methods and excluding fourth, fifth, and sixth virials in the Epstein equation of state, compressibility factors were calculated for all the four compounds to test the effect of higher virial terms. In the proposed method-(A) and method-(C), the …

Polypropylene Fibers, Anthony Vincent Galanti

Theses

One of the latest members of the rapidly growing therrnoplastic polymer family which appears capable of successfully competing with the currently saturated textile and chemical markets is polypropylene fiber. The objectives of this Thesis were to: (1) examine the effects of polymer characteristics and fiber processing conditions on the properties of polypropylene fibers, and (2) correlate all existing information on the physical, chemical, and mechanical properties of polypropylene fibers and comparatively evaluate this material with other fibers, natural and synthetic.

Polypropylene is the first member of a new group of polymers prepared by a mechanism defined as "stereospecific" polymerization. From …

Mass Transfer Into Cylindrical Liquid Films Measurement Of Liquid Diffusivities, Ronald Francis Lovenguth

Theses

This thesis was undertaken to augment and validate the previous work of Ratcliff and Reid⁽⁷⁾ in the area of diffusion of immiscible liquids. Their novel approach to this particular problem of liquid diffusion led the author to consider an experimental technique that has been used in gas-liquid studies. A short vetted-wall column was used to determine the rate of mass transfer of benzene and toluene into thin cylindrical films of water. A general analytical solution for the rate of mass transfer has been derived and is given below. This solution was checked using the system benzene-water.

G=3.63(Π(ρ_ω-ρ …

Thermal Conductivity Of Solid Materials, Irwin N. Huppert

Theses

A literature search on the methods of determining the thermal conductivity of solids has been made.

A compilation of the various methods of determining the thermal conductivity of solids presented in the literature is given in the report. In general, the literature is lacking in correlations of thermal conductivity with other properties of solid materials. A review of the correlations found is presented. A summary of data presented in the literature is presented in the text.

A method of determining the thermal conductivity of solid materials without measuring the heat flow through the test specimen is presented. The use of …

Esterification Of Oleic Acid With Oleyl Alcohol, Robert Persurance

Theses

The esterification of oleic acid with oleyl alcohol was studied. A literature search showed that the chemical kinetics for this reaction had not been studied previously.

In the temperature range of 150 to 200°C. and up to a conversion of about 85 per cent, the esterification was found to be a second order reaction when the water of reaction was removed from the system by simple distillation.

Para-toluenesulfonic acid is an effective catalyst for this system, and the observed specific rate constant is a linear function of the catalyst concentration.

The effect of temperature on the specific rate constant for …

The Purification, Analysis And Growth Of Single Crystals Of Organic Semiconductors, Melvin Leonard Druin

Theses

The purpose of this investigation was to design and construct a furnace for growing large single crystals of organic compounds by slow crystallization from the melt by the Bridgman technique. The crystals obtained by this furnace will be used in a later investigation of the intrinsic electrical and optical properties of organic semiconductors.

The methods describe have been used width success to produce large single crystals of anthracene and ethyl-p aminobenzoate with diameters of 1/2 inch.

The most promising methods of purification of anthracene, which were chemical synthesis, washing, recrystallization from solvents, sublimation, dimerization, co-distallatian and zone refining have been …

Effect Of Liquid Viscosity On Performance Of Wire Mesh Entrainment Separators, Raymond Paul Vogel

Theses

The knitted wire mesh entrainment separator, commonly referred to as a demister*, is in common use to separate entrained liquid from vapor streams. However, little quantitative information is available concerning the effect of physical properties of the entrained liquid on allowable gas velocities.

Studies were made on two demister styles to determine the effect of liquid viscosity on demister performance, Liquid viscosities from 0.9 to 12 centipoise were investigated using water, glycerine-water mixtures and heavy no. 2 fuel oil as the test liquids. Air was used as the gas medium in all cases.

Regression analysis of the test data indicates …

The Design And Fabrication Of A Cell To Measure The Thermal Conductivity Of Viscous Fluids, Donald William Hagedorn

Theses

The purpose of this investigation was to design and construct a device to measure the thermal conductivity of viscous fluids. The thermal conductivity data obtained with this device will be used in later work on predicting film coefficients of heat transfer to non-Newtonian fluids.

A cell of the concentric cylinder type was fabricated. Main features of the cell are: two concentric bronze cylinders separated by a 1/8 inch annular space, a central water capable of producing a 10° C temperature gradient in the annular space, and two guard heaters on individual rheostats to control the end looses. The temperatures are …

Slow Compression Crushing Of Glass In Fluids, Peter Joseph Lucchesi

Theses

Generally only a small fraction of the energy used in crushing, on the order of 1 or 2%, appears as new surface energy in the product. The purpose of this work was to determine if higher efficiencies could be achieved by the use of different fluids surrounding the particle during crushing.

Single particles of solid glass cylinders, standing on. end, were crushed by slow compression in the presence of air, water, methanol, carbon tetrachloride, and glycerol. No effect was found with the various fluids even when considerable pressure was developed in the surrounding fluid in some of the glycerol experiments. …

Carbon Tetrachloride-Xylene Equilibria, Michael Jay Ram

Theses

The liquid-liquid equilibria of the ternary systems carbon tetra-chloride-xylene-propylene glycol and carbon tetrachloride-xylene-diethylene glycol were investigated. The effectiveness of the glycols as selective solvents for xylene was represented by a plot of weight ratio xylene to carbon tetrachloride in each phase. It was found that the diethylene glycol was the better of the two solvents at concentrations resulting in more than 75% xylene in the xylene-carbon tetrachloride rich layer. At the lower xylene concentrations the propylene glycol was found more effective as a selective solvent.

Synthesis Of Trimethyl Borate By Ester Interchange, Hugh Murphy

Theses

Trimethyl borate was prepared by transesterification of a high—boiling methyl ester with a high—boiling trialkyl borate using a metal alcholate catalyst. Interchange occurred between n—amyl borate and the following methyl esters: dimethyl sulfate, parahydroxy methyl benzoate, methyl salicylate, and methyl stearate. Interchange also took place between methyl stearate and tribenzyl borate, tri—n—propyl borate, and tri—m, p—cresyl borate. Highest yields and purities resulted from reactions involving methyl stearate. Catalysts employed were magnesium—aluminum ethylate and aluminum Isopropoxide.

Two methods of separating the methanol—methyl borate azeotrope were evaluated: sulfuric acid extraction and salt splitting. Extraction with sulfuric acid was determined to be the …

A Study Of Continuous Photochemical Hydrolysis, Robert Parlante, Theodore Arthur Gropler

Theses

In this investigation, the ultraviolet absorption spectra and the batch photochemical hydrolysis of monochloroacetic and monobromoacetic acid, and their potassium and sodium salts, have been measured and compared with those existing in the literature.

The continuous photochemical hydrolysis of sodium chloroacetate has been investigated for the first time. The continuous photolysis of uranyl oxalate was investigated and used as a chemical actinometer.

Gaseous material in the reactant feed has been found to be important at low flow rates.

A Study Of The Fatty Alcohol-Epichlorohydrin Reaction, Roy Henry Schaufelberger

Theses

The reaction between "Lorol" 5 fatty alcohol and epichlorohydrin was found to proceed at a rate which could easily be followed, at temperatures of 80 to 140°C, when catalyzed with 0.05 percent of a boron trifluoride ether-ate catalyst, based on the total weight of reactants. The reaction was followed by determining the decrease in epichlorohydrin concentration with time using standard analytical techniques.

Kinetic studies showed that the fatty alcohol/epichlorohydrin reaction was not a simple pseudo first order or second order reaction but rather a complex one probably composed of:

1. A second order reaction between primary fatty alcohol and epichlorohydrin. …

Viscosity Of A Three Component System : Benzene-Ethanol-Acetic Acid At 20 Degrees C., 25 Degrees C., And 30 Degrees C, Alan Alvin Schetelich

Theses

The viscosity for the ternary system benzene-ethanol-acetic acid, has been determined. The viscosity maximum shown in the ethanol-acetic acid system is clearly distinguished in the ternary system as well. The viscosity minima which occur in the benzene-ethanol, and benzene-acetic acid systems are too slight to be readily apparent in the ternary system.

The ternary system viscosity was determined at temperatures of 20, 25, and 30° C. The effect of increasing the temperature from 20° C for the ternary system was to produce corresponding curves of lower viscosity. The maximum viscosity noted in the ternary system as well as the maximum …