Chemical Engineering Commons^™

Non-Isothermal Reaction-Diffusion Systems With Thermodynamically Coupled Heat And Mass Transfer, Yaşar Demirel

Papers in Analytical Chemistry

Non-isothermal reaction-diffusion (RD) systems control the behavior of many transport and rate processes in physical, chemical, and biological systems. A considerable work has been published on mathematically coupled nonlinear differential equations of RD systems by neglecting the possible thermodynamic couplings among heat and mass fluxes, and reaction velocities. Here, the thermodynamic coupling refers that a flux occurs without its primary thermodynamic driving force, which may be gradient of temperature, or chemical potential, or reaction affinity. This study presents the modeling equations of non-isothermal RD systems with coupled heat and mass fluxes excluding the coupling of chemical reactions using the linear …

Retrofit Of Distillation Columns Using Thermodynamic Analysis, Yaşar Demirel

Papers in Physical Properties

Thermodynamic analysis provides the column grand composite curves and exergy loss profiles, which are becoming readily available for a converged distillation column simulation. For example, the Aspen Plus simulator performs the thermodynamic analysis through its Column–Targeting tool for rigorous column calculations. This study uses the column grand composite curves and the exergy loss profiles obtained from Aspen Plus to assess the performance of the existing distillation columns, and reduce the costs of operation by appropriate retrofits in a methanol plant. Effectiveness of the retrofits is also assessed by means of thermodynamics and economics. The methanol plant utilizes two distillation columns …

Graphitized Carbon Foam With Phase Change Material, Angelinda D. Fedden

Theses and Dissertations

This thesis examines the transient heating and cooling responses of graphitized carbon foam infiltrated with phase change material (PCM). The carbon foam provides rapid heat transfer throughout the PCM volume, while the PCM stores the heat for later removal. The foam/PCM system was heated with a copper heating block, and then cooled with a liquid-cooled heat removal block. Infiltrating the foam with PCM significantly increased the length of time before the system reached maximum temperature. The temperature response of the foam/PCM system was consistent over multiple cycles of heating and cooling. A high density foam had a faster heating and …

Cycle Performance Of A Pulse Detonation Engine With Supercritical Fuel Injection, Timothy M. Helfrich

Theses and Dissertations

Pulse detonation engines (PDE) rely on rapid ignition and formation of detonation waves. Because hydrocarbon fuels are composed typically of long carbon chains that must be reduced in the combustion process, it would be beneficial to create such reduction prior to injection of fuel into the engine. This study focused on PDE operation enhancements using dual detonation tube, concentric-counter-flow heat exchangers to elevate the fuel temperature up to supercritical temperatures. Variation of several operating parameters included fuel type (JP-8, JP-7, JP-10, RP-1, JP-900, and S-8), ignition delay, frequency, internal spiral length, and purge fraction. To quantify the performance, four key …

Stability Of Transport And Rate Processes [Review], Yaşar Demirel

Papers in Thermal Mechanics

About fifty years ago, the Turing instability demonstrated that even simple reaction-diffusion systems might lead to spatial order and differentiation, while the Rayleigh-Bénard instability showed that the maintenance of nonequilibrium might be the source of order in fluids subjected to a thermodynamic force above a critical value. Therefore, distance from global equilibrium in the form of magnitude of a thermodynamic force emerges as another constraint of stability; some systems may enhance perturbations, and evolve to highly organized states called the dissipative structures after a critical distance on the thermodynamic branch. Although the kinetics and transport coefficients represent short-range interactions, chemical …

Thermal Characteristics Of Pitch Based Carbon Foam And Phase Change Materials, Kevin W. Wierschke

Theses and Dissertations

Phase-change thermal energy storage devices offer thermal control systems an option that allows a smaller heat sink to be used by absorbing the thermal energy quickly and storing it in the phase change to prevent failure of electronic components and then slowly releasing the heat to the heat sink. This paper experimentally determined the transient response of carbon foam with a phase-change material by measuring the response to a step temperature input to test samples. The transient response was recorded until steady state was reached. An analytic response was created and compared against the measured response. A simplified analytic prediction …

Thermodynamic Analysis Of Separation Systems, Yaşar Demirel

Papers in Thermal Mechanics

Separation systems mainly involve interfacial mass and heat transfer as well as mixing. Distillation is a major separation system by means of heat supplied from a higher temperature level at the reboiler and rejected in the condenser at a lower temperature level. Therefore, it resembles a heat engine producing a separation work with a rather low efficiency. Lost work (energy) in separation systems is due to irreversible processes of heat, mass transfer, and mixing, and is directly related to entropy production according to the Gouy-Stodola principle. In many separation systems of absorption, desorption, extraction, and membrane separation, the major irreversibility …

Exergy Use In Bioenergetics, Yaşar Demirel

Papers in Analytical Chemistry

Every developed and adapted biological system extracts useful energy from outside, converts, stores it, and uses for muscular contraction, substrate transport, protein synthesis, and other energy utilizing processes. This energy management in a living cell is called the bioenergetics, and the useful energy is the exergy, which is destroyed in every irreversible process because of the entropy production. The converted exergy is the adenosine triphosphate (ATP) produced through the oxidative phosphorylation coupled to respiration in which the exergy originates from oxidation of reducing equivalents of nutrients. A living cell uses the ATP for all the energy demanding activities; it has …

Review Of The Product Development Process And Information Flow In The Manufacturing Industry: Problems And A Possible Wav Forward, E Opiyo

Tanzania Journal of Engineering and Technology (TJET)

No abstract provided.

Design And Simulation Of An Induction Skull Melting System, Taide Tan

UNLV Theses, Dissertations, Professional Papers, and Capstones

Incorporating volatile actinides, mainly americium into a metallic fuel pin (MFP) has been a serious problem due to americium’s high vapor pressure. An Induction Skull Melting (ISM) system was identified by Argonne National Laboratory (ANL) as a potential furnace design to cast MFPs. Through the development of the ISM system, the nuclear waste feedstock can be melted and injected into the mold for fabricating MFPs in the advanced nuclear fuel cycles. The main phenomena in this system include: induction melting process, casting process and mass transfer process of americium. Issues related to ISM system design for casting MFPs are discussed …

Effect Of Plasma Flux Composition On The Nitriding Rate Of Stainless Steel, Christopher Muratore, Scott G. Walton, D. Leonhardt, Richard F. Fernsler, David D. Blackwell, R. A. Meger

Chemical and Materials Engineering Faculty Publications

The total ion flux and nitriding rate for stainless steel specimens exposed to a modulated electron beam generated argon-nitrogen plasma were measured as a function of distance from the electron beam axis. The total ion flux decreased linearly with distance, but the nitriding rate increased under certain conditions, contrary to other ion flux/nitriding rate comparisons published in the literature. Variation in ion flux composition with distance was explored with a mass spectrometer and energy analyzer as a possible explanation for the anomalous nitriding rate response to ion flux magnitude. A transition in ion flux composition from mostly N2 1 to …

Gibbs Dividing Surface And Helium Adsorption, Sasidhar Gumma, Orhan Talu

Chemical & Biomedical Engineering Faculty Publications

All adsorption data is based on the definition of Gibbs dividing surface, which is a purely mathematical transformation. Adsorption measurements in microporous solids necessitate experimental determination of the dividing surface. An international protocol does not exist on how to perform this important measurement. Commonly, helium is assumed not to adsorb and used as a probe molecule for this measurement. Each experimentalist chooses an arbitrary set of conditions, often without even disclosing them, which adds to the confusion in adsorption literature. Here, a self-consistent method for the analysis of helium data is proposed which does not assume non-adsorbing helium …

Experimental Energy Performance Of Open Cooling Towers Used Under Low And Variable Approach Conditions For Indirect Evaporative Cooling Of Buildings, Ben Costelloe, Donal Finn

Articles

The success of chilled ceilings and displacement ventilation systems as a means of sensible cooling in buildings has prompted a review of evaporative cooling technology as an effective means of generating the required cooling water. When such cooling water is generated at low approach conditions (2–5 K), at the higher temperatures required in these systems (14–18°C), very high levels of availability result. In many north western European locations the levels of availability are such that the prospect of supplanting rather than simply supplementing the refrigeration system, for sensible cooling purposes, arises. The viability of the technique, however, largely depends on …

Indirect Evaporative Cooling Potential In Air-Water Systems In Temperate Climates, Ben Costelloe, Donal Finn

Articles

Recent developments have prompted a review of evaporative cooling technology as an effective means of cooling modern deep plan buildings. Prominent among these developments is the success of high temperature sensible cooling systems, particularly, chilled ceilings, which require a supply of cooling water at 14–18 °C. Crucial to the success of evaporative cooling technology, as a significant means of cooling in modern applications, is the ability to generate cooling water, in an indirect circuit, at a temperature which closely approaches the ambient adiabatic saturation temperature (AST) or wet bulb temperature (WBT). Recent experimental research has demonstrated that it is technically …

Development Of A Model For Induction Heating, Randy Clarksean, Yitung Chen

Fuels Campaign (TRP)

There are two coupled equations that must be solved in order to determine the power deposition. The numerical solution of these equations is needed in order to apply a source term within the energy equations. These equations have previously solved in FIDAP. That implementation used modified versions of the momentum and energy equations to provide a mechanism for the solution of two coupled equations. Currently, we want to solve for the induction heating field in addition to the flow field and the energy equation. In order to do this, a mechanism has to be defined within FIDAP to solve these …

The Fission Properties Of Curium Separated From Spent Nuclear Fuel, William Culbreth, Elizabeth Bakker, Jason Viggato

Separations Campaign (TRP)

Curium poses special problems in the chemical preparation of spent nuclear fuel for transmutation. Once separated from the other minor actinides, the seven curium isotopes in spent fuel can lead to nuclear fission with the subsequent release of a large amount of radiation. Several isotopes of curium also generate a significant amount of heat by radioactive decay. Sustained fission can be avoided by preventing the accumulation by more that a critical mass of curium. The heat generation of curium presents even more restriction on the mass of curium that can safely be contained in one location.

To analyze the nuclear …

Thermodynamics And Bioenergetics, Yaşar Demirel, Stanley I. Sandler

Papers in Thermal Mechanics

Bioenergetics is concerned with the energy conservation and conversion processes in a living cell, particularly in the inner membrane of the mitochondrion. This review summarizes the role of thermodynamics in understanding the coupling between the chemical reactions and the transport of substances in bioenergetics. Thermodynamics has the advantages of identifying possible pathways, providing a measure of the efficiency of energy conversion, and of the coupling between various processes without requiring a detailed knowledge of the underlying mechanisms. In the last five decades, various new approaches in thermodynamics, non-equilibrium thermodynamics and network thermodynamics have been developed to understand the transport and …

Thermodynamics And Bioenergetics, Yaşar Demirel, Stanley I. Sandler

Papers in Thermal Mechanics

Bioenergetics is concerned with the energy conservation and conversion processes in a living cell, particularly in the inner membrane of the mitochondrion. This review summarizes the role of thermodynamics in understanding the coupling between the chemical reactions and the transport of substances in bioenergetics. Thermodynamics has the advantages of identifying possible pathways, providing a measure of the efficiency of energy conversion, and of the coupling between various processes without requiring a detailed knowledge of the underlying mechanisms. In the last five decades, various new approaches in thermodynamics, non-equilibrium thermodynamics and network thermodynamics have been developed to understand the transport and …

Molecular Simulation Of Adsorption: Gibbs Dividing Surface And Comparison With Experiment, Orhan Talu, Alan L. Myers

Chemical & Biomedical Engineering Faculty Publications

At low temperature near the normal boiling point, computer simulations of adsorption of gases can be compared directly with experiment. However, for adsorptive gas separations in which the gas is adsorbed near or above its critical temperature, absolute simulation variables must be converted to excess variables for comparison with experiment. The conversion of absolute to excess variables requires the helium pore volume of the adsorbent. Lennard-Jones potential parameters for helium gas molecules interacting with the oxygen atoms of silicalite are ε/k = 28.0 K and σ = 2.952 Å. The helium pore volume of silicalite is 0.175 cm …

Effects Of Concentration And Temperature On The Coupled Heat And Mass Transport In Liquid Mixtures, Yaşar Demirel, Stanley I. Sandler

Papers in Thermal Mechanics

Using published experimental data on the thermal conductivity, mutual diffusivity, and heats of transport, the degree of coupling between heat and mass flows has been calculated for binary and ternary nonideal liquid mixtures. The binary mixtures consist of two types: the first is six systems of six-to-eight-carbon straight and branched chain alkanes in chloroform and in carbon tetrachloride; and the second is mixtures of carbon tetrachloride with benzene, toluene, 2-propanone, n-hexane, and 11-octane. The ternary mixture considered is toluene-chlorobenzene-bromobenzene. The published data are available at 35°C, 30°C, and 35°C and ambient pressure. Using the linear nonequilibi-ium thermodynainics (LNET) and the …

Linear-Nonequilibrium Thermodynamics Theory For Coupled Heat And Mass Transport, Yaşar Demirel, Stanley I. Sandler

Yaşar Demirel Publications

Linear-nonequilibrium thermodynamics (LNET) has been used to express the entropy generation and dissipation functions representing the true forces and flows for heat and mass transport in a multicomponent fluid. These forces and flows are introduced into the phenomenological equations to formulate the coupling phenomenon between heat and mass flows. The degree of the coupling is also discussed. In the literature such coupling has been formulated incompletely and sometimes in a confusing manner. The reason for this is the lack of a proper combination of LNET theory with the phenomenological theory. The LNET theory involves identifying the conjugated flows and forces …

Entropy Generation Method To Quantify Thermal Comfort, S. C. Boregowda, S. N. Tiwari, S. K. Chaturvedi

Mechanical & Aerospace Engineering Faculty Publications

The present paper presents a thermodynamic approach to assess the quality of human-thermal environment interaction and quantify thermal comfort. The approach involves development of entropy generation term by applying second law of thermodynamics to the combined human-environment system. The entropy generation term combines both human thermal physiological responses and thermal environmental variables to provide an objective measure of thermal comfort. The original concepts and definitions form the basis for establishing the mathematical relationship between thermal comfort and entropy generation term. As a result of logic and deterministic approach, an Objective Thermal Comfort Index (OTCI) is defined and established as a …

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna

Tanzania Journal of Engineering and Technology (TJET)

Vibration is one of the techniques employed in the determination of dynamic properties of fruits and vegetables. It entails generation of a mechanical or acoustic vibrational signal which is propagated through the flesh of the agricultural material. A transducer is either attached or held close to the specimen to monitor the propagation of the signal through the specimen. The manner in which the signal is transmitted through the material is analyzed, and the dynamic properties of the specimen which relate to its firmness or its internal being are derived. The technique has been around for the past 30 years or …

Editorial, Orhan Talu, Shivaji Sircar

Chemical & Biomedical Engineering Faculty Publications

No abstract provided.

Copper Alloy-Impregnated Carbon-Carbon Hybrid Composites For Electronic Packaging Applications, S. K. Datta, Surendra N. Tewari, Jorge E. Gatica, W. Shih, L. Bentsen

Chemical & Biomedical Engineering Faculty Publications

Porous carbon-carbon preforms, based on three-dimensional networks of PAN (Polyacrylonitrile)-based carbon fibers and various volume fractions of chemical vapor-deposited (CVD) carbon, were impregnated by oxygen-free, high-conductivity (OFHC) Cu, Cu-6Si-0.9Cr, and Cu-0.3Si-0.3Cr (wt pct) alloys by pressure infiltration casting. The obtained composites were characterized for their coefficient of thermal expansion (CTE) and thermal conductivity (K) along the through-thickness and two in-plane directions. One composite, with a 28 vol pct Cu-0.3Si-0.3Cr alloy, showed outstanding potential for thermal management applications in electronic applications. This composite exhibited approximately isotropic thermal expansion properties (CTE = 4 to 6.5 ppm/K) and thermal conductivities (k greater than …

Computation Of Flame Base Height Of A Turbulent Diffusion Flame Resulting From A Methane Jet, A. S. Kheireddine, S. K. Chaturvedi, T. O. Mohieldin

Mechanical & Aerospace Engineering Faculty Publications

This work summarizes numerical results for a diffusion flame formed from a cylindrical tube fuel injector, issuing a gaseous methane jet vertically in a quiescent atmosphere. The primary objective is to predict the flame base height and other flame characteristics as a function of the fuel jet velocity. A finite volume scheme is used to discretize the time-averaged Navier-Stokes equations for the reacting flow resulting from the turbulent fuel jet motion. The turbulent stresses, and heat and mass fluxes are computed from a Reynolds stress turbulence model. A chemical kinetics model involving two-step chemistry is employed for the oxidation of …

Entropy Generation In A Rectangular Packed Duct With Wall Heat Flux, Yaşar Demirel, Ramazan Kahraman

Papers in Thermal Mechanics

The entropy generation due to heat transfer and friction has been calculated for fully developed, forced convection flow in a large rectangular duct, packed with spherical particles, with constant heat fluxes applied to both the top (heated) and bottom (cooled) wall. An approximate analytical expression for the velocity profile developed for packed bed with H/dp > 5 has been used together with the energy equation of fully developed flow to calculate the non isothermal temperature profiles along the flow passage. The velocity profile takes into account the increase in the velocity near the wall due to the higher voidage in this …

The Effectiveness Of Film Cooling In A Hypersonic Flowfield With Favorable Pressure Gradients, Julie A. Young

Mechanical & Aerospace Engineering Theses & Dissertations

The impetus of this technical document is to report results of aerothermodynamic cooling of a scramjet nozzle under favorable pressure gradients. The goals of film cooling are to protect the nozzle skin from the high enthalpy combustor flow, reduce regenerative cooling requirements, and decrease nozzle skin friction. A hypersonic nozzle configuration for which experimental data exists was selected as the basis of this numerical study. As a first step, the numerical results of film cooling along a flat plate are compared to previous literature to validate the numerical model. Subsequently, computations are performed to study the effects of varying the …

Behavior And Performance Of Adsorptive Natural Gas Storage Cylinders During Discharge, K. J. Chang, Orhan Talu

Chemical & Biomedical Engineering Faculty Publications

Adsorbed natural gas (ANG) has the potential to replace compressed natural gas in mobile storage applications, such as in vehicles. Although a substantial research effort has been devoted to ANG, very few studies evaluate the impact of heat of adsorption on system performance. This paper concentrates on the impact of heat of adsorption on ANG performance during discharge, while the gas outflow rate is dictated by the energy demand of the application. The temperature drop and performance loss was measured with commercially available ANG cylinders under realistic conditions. Data show as high as a 37°C temperature drop at …

Droplet Evaporation And Deformations In An Amplitude Modulated Ultrasonic Field, Nihad E. Daidzic, Rene Stadler, Adrian Melling

Aviation Department Publications

The aim of the report presented is the measurements of droplet oscillations.