Chemical Engineering Commons^™

Economic Feasibility Of Mixed Plastic Waste Pyrolysis Using Twin Reactor System In Northwest Arkansas, Carol Rogers, Patricia Means, Renato Gonzalez, Kaida Sheets, Hayden Townsend

Chemical Engineering Undergraduate Honors Theses

Plastic waste generation is increasing at an unsustainable rate while recycling solutions remain stagnant. As a chemical means of recycling, mixed plastic waste pyrolysis can generate synthetic oil appropriate for use as fuel in power generation from plastic waste that otherwise accumulates in landfills. With the scaling of a commercial plastic pyrolysis process in Northwest Arkansas (NWA) modeled after an operational sawdust pyrolysis unit in Huntsville, Arkansas, economic analysis resulted in 26.3% internal rate of return. Therefore, construction of a commercial mixed plastic-to-fuel pyrolysis plant is economically justified and should be pursued. To effectively implement the proposed design, NWA must …

Predicting Henry's Law Constants Of Volatile Organic Compounds Present In Bourbon Using Molecular Simulations., Christopher A Abney

Electronic Theses and Dissertations

Henry’s Law describes the partitioning of molecules into liquid and gas phases at low concentrations. Henry’s Law, which is based upon a species-dependent constant and the gas phase partial pressure, is useful for predicting phase behavior of dilute solutes. However, Henry’s Law constants are difficult to measure experimentally or to predict using structure-property or thermodynamic models. Herein, molecular simulations were used to calculate Henry’s Law constants for 18 volatile organic compounds (VOCs) present in bourbon. The novel simulations analyzed solvation thermodynamics of small organic molecules in 120 proof ethanol. A fast-growth non-equilibrium free energy method was used in which the …

Graphical Design And Analysis Of Mass Exchange Networks Using Composition Driving Forces, Nessren Mohamed Farrag, Dina Ahmed Kamel, Ayat Ossama Ghallab, Mamdouh Ayad Gadalla, Mai Kamal Fouad

Chemical Engineering

Pinch analysis is a methodology for minimizing energy and mass consumption in different industries. It has been widely applied for more efficient processes. This study presents a new graphical-approach to analyze and design Mass Integration (MI) and exchange networks that follows Pinch principles to guarantee maximum mass recovery with minimum losses. This technique uses the composition driving forces in network representation as it rules the mass transfer between streams. The proposed approach can be applied on both existing mass networks as well as new ones. This graphical representation a visual descriptive design tool to describe and explain the details of …

Relationship Between Thermal Conductivity And Free Electrons In Metal, Yansong Liu

Senior Theses

An experiment was designed and conducted to explore the relationship between thermal conductivity with free electrons in metal. In the experiment, copper, iron, aluminum, and titanium rods with close diameters were used to carry out the experiment. Each rod was heated up by a heat unit at one end while cooled on the other end with a heat sink to maintain a steady state. DC current was applied to rods in the direction along, as well as against, the heat flow. Thermal conductivities were measured in these two situations for each rod. Results showed electrons do dominate thermal flow inside …

Thermal And Thermophysical Properties Of Anionic Amines And Their Aqueous Solutions For Co2 Capture In Confined Environments, Randi Swanson

Honors Theses

Air revitalization for the International Space Station (ISS) has been identified by NASA as a mission critical need which requires improvement. The current method uses13X zeolite, a solid adsorbent, to adsorb carbon dioxide. While this is effective, the zeolite adsorbent produces dust that is unwelcome on the space station. Furthermore, the adsorbentis too sensitive to humidity in moderate temperature gas streams [1]. Aqueous solutions of ionic amines show promise as a safe and efficient solution, as they do not volatilize and are not water sensitive [2]. Specifically, anionic amines have the most potential because of the amine functional group’s ability …

Understanding Absorption, Supersaturation, And Drug Activity In Solution: Working Towards Developing A More Biorelevant Media, Freddy Arce

Theses and Dissertations--Pharmacy

With the looming dominance of poorly water-soluble chemical entities within the pharmaceutical pipeline, the pharmaceutical industry has leaned on the use of supersaturating drug delivery systems (SDDSs) to achieve efficacious concentrations within the gastrointestinal fluids. SDDSs aim to achieve concentrations in solutions greater than the solubility of the lowest energy crystalline form. However, the generation of supersaturated solutions of active pharmaceutical ingredients (APIs) creates a strong crystallization potential, which is undesirable.

In product development, supersaturating products often fail in Phase I and Phase II clinical trials due to poor oral bioavailability and a lack of in vivo efficacy. Pre-clinical testing …

Ultrafast Thermal Modification Of Strong Coupling In An Organic Microcavity, Bin Liu, Vinod M. Menon, Matthew Y. Sfeir

Publications and Research

There is growing interest in using strongly coupled organic microcavities to tune molecular dynamics, including the electronic and vibrational properties of molecules. However, very little attention has been paid to the utility of cavity polaritons as sensors for out-of-equilibrium phenomena, including thermal excitations. Here, we demonstrate that non-resonant infrared excitation of an organic microcavity system induces a transient response in the visible spectral range near the cavity polariton resonances. We show how these optical responses can be understood in terms of ultrafast heating of electrons in the metal cavity mirror, which modifies the effective refractive index and subsequently the strong …

Dynamic Modelling And Control Of Grid-Level Energy Storage Systems, Sai Pushpitha Vudata

Graduate Theses, Dissertations, and Problem Reports (ETD)

The focus of this work is on two energy storage technologies, namely pumped storage hydroelectricity (PHS) and secondary batteries. Under secondary battery technologies, two potential technologies for grid-scale storage, namely high-temperature sodium-sulfur (NaS) battery and vanadium redox flow battery (VRFB), are investigated. PHS is a largescale (>100 MW) technology that stores and generates energy by transporting water between two reservoirs at different elevations. The goal is to develop a detailed dynamic model of PHS and then design the controllers to follow the desired load trajectory accurately with high efficiency. The NaS battery and VRFB are advanced secondary batteries which …

Testing The Effectiveness Of Various Fabrics For Use In Protective Face Coverings, Isaac Daley

Williams Honors College, Honors Research Projects

Facemask requirements have been heavily implemented as a result of the COVID-19 pandemic. The purpose of this study was to test various fabrics that could be used in face coverings and determine which materials are best for reducing virus transmission rates. Of the seven fabrics tested, five were conventional home-use fabrics and the other two were surfaces modified with hydrophobic organosilanes. Wettability and droplet adherence tests were performed on each material. The materials that performed the best were decyltrichlorosilane (DTS) modified cotton, perfluorotrichlorosilane (FTS) modified cotton, and polyester. Contact angles for water droplets on these fabrics were 106°, 93°, and …

Continuous Preparation And Application Of Novel Heterogeneous Catalysis, Michael B. Burkholder

Theses and Dissertations

Transition metal heterogeneous catalysts are widely used across many chemical industries to reduce waste and emissions and reduce production time while increasing rate. The prevalence of these materials results from the complex relationship between metal nanoparticles and supports affecting final catalytic performance. Rational catalyst synthesis describes the ability to precisely engineer structures through controlled preparation. Novel materials and continuous processing represent a promising approach for rational catalyst synthesis.

The application of these catalysts in continuous, multiphase processes, such as cross-coupling reactions, oxidation chemistry, and nitroreduction processes, are paramount to developing new commercial routes for high-value products. Pd/G catalysts synthesized by …

Interactions Of Lignin Dimers With Engineered Surfaces And Model Cell Membranes For Design Of Lignin-Based Materials, Mahsa Moradipour

Theses and Dissertations--Chemical and Materials Engineering

Capitalizing on byproducts of industrial and agricultural economies is among the utmost goals of sustainability. Of particular interest for commercial upgrading is lignin, a phenolic biopolymer found in the cell walls of plants which is the second most abundant biopolymer on Earth after cellulose. Due to its heterogeneous structure, deconstructing lignin to selected small molecules for use as chemicals or advanced materials has been elusive. This work capitalizes on a “bottom up” approach to the synthesis of lignin oligomers of known bond chemistry to better understand their interfacial interactions.

The potential pharmacological mechanism of lignin deconstruction components and their toxicological …

Thermal/Structural Analysis Of The Axion Quantum Metrology Cavity And Its Components, Tyler Funk

Graduate Research Theses & Dissertations

This research was centered around maximizing the capability to cool dielectric material within a containment unit, or Photonic Band Gap (PBG) cavity, designed for detecting axion dark matter and identifying the unit’s thermal properties. There are multiple types of PBG cavities, but the latest version that axion researchers wish to use has been theorized to contain possible issues related to its thermal properties. Thermal conductivity is an issue with the dielectric material because it is made from alumina which is highly insulative. This is important since the research is being done in a cryogenic environment and the thermal noise affects …

Tailoring Thermoresponsive Poly(N-Isopropylacrylamide) Toward Sensing Perfluoroalkyl Acids, Dustin Thomas Savage

Theses and Dissertations--Chemical and Materials Engineering

Widespread distribution of poly- and perfluoroalkyl substances (PFAS) in the environment combined with concerns for their potentially negative health effects has motivated regulators to establish strict standards for their surveillance. The United States Environmental Protection Agency issued a cumulative domestic threshold of 70 ppt for water supplies, and this bar is even lower in some local districts and other countries. Monitoring PFAS consequently requires sensitive analytical equipment to meet regulatory specifications, and liquid chromatography with tandem mass spectroscopy (LC/MS/MS) is the most common technique used to satisfy these requirements. Though extremely sensitive, the instrument is often burdened by pretreatment regimens, …

New Horizons For Processing And Utilizing Red Mud, M. Archambo

Dissertations, Master's Theses and Master's Reports

Red mud is an industrial slurry waste that is produced as a byproduct of the Bayer process for alumina. The waste is generated in large quantities, up to a ratio of 2:1 against the valued product alumina. Red mud exhibits many chemical and physical properties that categorize it as a hazardous material. Due to the addition of sodium hydroxide in processing, the pH is typically at values close to 13. Small particle size discourages separation from water for disposal, so drying red mud happens over many years.

The pH of red mud can be reduced with inexpensive reagents. Carbon dioxide …

Reduction Of Copper And Iron Oxide Mixture With Local Reducing Gases, Shokhrukh Khojiev

Acta of Turin Polytechnic University in Tashkent

The article analyzes the scientific problems of the copper industry. In particular, the main problem with the classical production of copper is the causes of large amounts of slag and the negative impact of these wastes on the environment. Accordingly, the main component that forms the slag is iron, and the higher its content in the original copper concentrate, the more slag is formed, and at the same time a large amount of copper metal is released into the waste. The departure is indicated by evidence. To prevent this problem, a technology has been proposed to reduce copper sulfide concentrates …

A Computational Investigation Of The Interstitial Oxidation Thermodynamics Of A Mo-Nb-Ta-W High Entropy Alloy Beyond The Dilute Regime, Adib J. Samin

Faculty Publications

High entropy alloys (HEAs) are promising candidates for high-temperature structural material applications. Oxidation is a major factor that must be accounted for when designing such materials and it is thus important to study the oxidation behavior of HEAs to enable the optimum design of next generation materials. In this study, the thermodynamic behavior of interstitial oxygen in a Mo-Nb-Ta-W high entropy alloy was explored beyond the dilute limit. This was accomplished by sampling configurations of the HEA and HEA-oxygen systems from an isothermal–isobaric ensemble using a series of first-principle-based Monte Carlo simulations. It was found that the interstitial oxygen had …

Enhancement Of Regeneration Ratio And Thermal Durability For Regenerated Fiber Bragg Grating Based On Pre-Annealing Treatment And Multimaterial Fibers, Nurul Asha Mohd Nazal

Student Works (2020-2029)

Regenerated fiber Bragg grating (RFBG) or also known as regenerated grating (RG) is the creation of the temperature resistant grating through thermal erasure of seed grating (SG) followed by a rebirth of new grating in a annealing process. RG has shown to be a promising fiber Bragg grating component for operation under very high ambient temperature condition. Nonetheless, further investigation and improvement are required to better understand its formation mechanism and to enhance its performance. This study aims to enhance the regeneration ratio and thermal durability of the RG based on pre-annealing treatment and multimaterial fiber. In this work, the …

The Varied Thermal Response Of Magnetic Iron-Oxide Nanoparticles During Induction Heating In Liquid And Solid-Liquid Phase Change Mediums, Joshua Tompkins

Graduate Theses and Dissertations

This study investigates the induction heating response of uncapped iron oxide nanoparticles sonically dispersed as a nanofluid and mechanically distributed in solid phase change materials. The nanoparticles examined have a mean diameter of 14.42 nm and are magnetically heated in an alternating magnetic field at an amplitude of 72.6 kA/m at frequencies of 217, 303, and 397 kHz. Nanoparticle characterization was undertaken through transition electron microscopy, x-ray diffraction, and dynamic light scattering when in suspension. Carrier fluids were characterized through viscosity, heat capacity, and density measurements which were used in the calorimetric calculation of the specific absorption rate (SAR) of …

A Parametric Analysis Of A Turbofan Engine With An Auxiliary Bypass Combustion Chamber – The Turboaux Engine, Kaleab Fetahi

Mechanical & Aerospace Engineering Theses & Dissertations

A parametric study of a novel turbofan engine with an auxiliary combustion chamber, nicknamed the TurboAux engine is presented. The TurboAux engine is conceived as an extension of a low-bypass turbofan engine with an auxiliary bypass annular combustion chamber around the core stream. The study presented in this thesis is motivated by the need to facilitate clean secondary burning of fuel at temperatures higher than conventionally realized, from air exiting the low-pressure compressor. The parametric study starts by analyzing the turbojet engine and its performance with and without an afterburner segment attached. Following that, the conventional turbofan and its mixing …

Parametric Study Of Residual Stresses In Wire And Arc Additive Manufactured Parts, Hisham Khaled Jamil Abusalma

Mechanical & Aerospace Engineering Theses & Dissertations

Wire and Arc Additive Manufacturing (WAAM) is a cost-effective additive manufacturing process due to its capability to fabricate large metal parts with high deposition rate and low equipment cost. Although this method is gaining popularity in manufacturing industry, more research is needed to understand process parameters’ effects on residual stress (RS) distribution and part distortion. As such, a 3D thermo-elastic-plastic transient model was established in ABAQUS and employed to investigate the effect of process parameters such as the torch speed, the deposition power and the interlayer dwell time on RS distribution and distortion in WAAM part. The numerical model utilized …

Thermal Control Development Of A Proton Exchange Membrane Fuel Cell System, Ola Mohammed Taha Al-Shalash

Mechanical Engineering Theses

A fuel cell is an electrochemical energy conversion device that uses fuel to generate electricity. It basically converts the chemical energy of reactants directly into electricity without combustion. In a Proton Exchange Membrane Fuel Cell (PEMFC), the reactants, hydrogen and oxygen, are fed into the two electrodes, anode and cathode, respectively. A reaction takes place at each electrode and produces electricity, as well as water, and heat as the by-products. In order to maximize performance of a fuel cell, many factors can be considered for tuning and control. Temperature management is one of these factors.

A thermal-fluid model of a …

Thermodynamic Analysis And Optimization Of Organic Rankine Cycles Using 1-Butylpyridinium Tetrafluoroborate As A Geothermal Fluid, Kazemi Shabnam

Student Works (2020-2029)

Organic Rankine cycle (ORC) is a promising technology for electricity generation by utilizing heat sources at low to moderate temperature that ranges between 80-350° C. In the present work, an ionic liquid (1-butylpyridinium tetrafluoroborate, C9H14NBF4), a known green chemical and non-volatile compound with good thermal and chemical stability, significant heat capacity, low vapor pressure and a wide liquid temperature range (25 to 459 °C), is utilized as a geothermal fluid. Simulation and optimization were conducted for a basic organic Rankine cycle (basic ORC), a regenerative organic Rankine cycle (RORC) and a two-stage evaporative organic Rankine cycle (TSORC) by maximizing exergy …

What Difference Does A Catalyst Make?, Tammy Guthrie, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use different catalysts for the decomposition of Hydrogen Peroxide, to determine if different catalysts affect the energy that is generated during the reaction.

A Study Of The Thermodynamics Of Small Systems And Phase Transition In Bulk Square Well-Hard Disk Binary Mixture, Gulce Kalyoncu

Graduate Theses and Dissertations

Under the umbrella of statistical mechanics and particle-based simulations, two distinct problems have been discussed in this study. The first part included systems of finite clusters of three and 13 particles, where the particles are interacting via Lennard Jones potential. A machine learning technique, Diffusion Maps (DMap), has been employed to the large datasets of thermodynamically small systems from Monte Carlo simulations in order to identify the structural and energetic changes in these systems. DMap suggests at most three dimensions are required to describe and identify the systems with 9 (N = 3) and 39 (N = 13) dimensions. At …

Nonlinear Dimensionality Reduction For The Thermodynamics Of Small Clusters Of Particles, Aditya Dendukuri

Graduate Theses and Dissertations

This work employs tools and methods from computer science to study clusters comprising a small number N of interacting particles, which are of interest in science, engineering, and nanotechnology. Specifically, the thermodynamics of such clusters is studied using techniques from spectral graph theory (SGT) and machine learning (ML). SGT is used to define the structure of the clusters and ML is used on ensembles of cluster configurations to detect state variables that can be used to model the thermodynamic properties of the system. While the most fundamental description of a cluster is in 3N dimensions, i.e., the Cartesian coordinates of …

Semi-Lagrangian Implicit Bhatnagar-Gross-Krook Collision Model For The Finite-Volume Discrete Boltzmann Method, Leitao Chen, Sauro Succi, Xiaofeng Cai, Laura Schaefer

Publications

In order to increase the accuracy of temporal solutions, reduce the computational cost of time marching, and improve the stability associated with collisions for the finite-volume discrete Boltzmann method, an advanced implicit Bhatnagar-Gross-Krook (BGK) collision model using a semi-Lagrangian approach is proposed in this paper. Unlike existing models, in which the implicit BGK collision is resolved either by a temporal extrapolation or by a variable transformation, the proposed model removes the implicitness by tracing the particle distribution functions (PDFs) back in time along their characteristic paths during the collision process. An interpolation scheme is needed to evaluate the PDFs at …

Comparative Analysis Of Simulation Models Of The Production Of Ethylbenzene, Osariemen Imafidon

Honors Theses

Process Engineering is all about making sure a raw material can become the desired product with as little variation as possible, while achieving the customer's specifications. Many equipment used for chemical processes cannot be physically inspected during operation at steady state, hence, the need for simulation software. The objective of this study was to compare the results of three different simulation packages to evaluate their efficacy within process design.

This study focused on the economic analysis of the production of Ethylbenzene using various models. The base case variables were inputted into each model to simulate the calculations for a fully …

Improving Pv Module Efficiency Through Cooling, Blake Bradley

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …

Solution To Exide Technologies Inbatec Inefficiency, Shixuan Hou, Reagan Gilker, Mary Fairley, Spencer Christian, Covenson Latouche

Chemical Engineering Undergraduate Honors Theses

The inefficiency of the battery charging time in Inbatec Units 1 and 2 in the Exide Technologies Fort Smith was initially investigated by a student team in Fall 2019, and the investigation was continued into Spring 2020. The Exide Technologies facility in Fort Smith, Arkansas utilizes 13 Inbatec units to charge the lead-acid batteries. The Inbatec systems circulate the sulfuric acid solution through a cooling tower to maintain to optimal charging temperature. Previous analysis of the charging process for Inbatec Units 1 and 2 show the cooling tower have the capacity to quickly remove the excess heat in the sulfuric …

Solution To Exide Technologies Inbatec Inefficiency, Mary Fairley, Reagan Gilker, Spencer Christian, Shixuan Hou, Covenson Latouche

Chemical Engineering Undergraduate Honors Theses

The inefficiency of the battery charging time in Inbatec Units 1 and 2 in the Exide Technologies Fort Smith was initially investigated by a student team in Fall 2019, and the investigation was continued into Spring 2020. The Exide Technologies facility in Fort Smith, Arkansas utilizes 13 Inbatec units to charge the lead-acid batteries.

The Inbatec systems circulate the sulfuric acid solution through a cooling tower to maintain to optimal charging temperature. Previous analysis of the charging process for Inbatec Units 1 and 2 show the cooling tower have the capacity to quickly remove the excess heat in the sulfuric …