Chemical Engineering Commons^™

Development Of Novel Adsorbent For Industrial Waste Water Treatment, Islam M. Al-Akraa, Hassan M. Shehata Eng, Dalia A. Ali Eng., Hoda A. Elsawy Dr

Chemical Engineering

The main objective of this research project is to perform some experimental procedures to inform the ability of the novel adsorbent used in this project. The chemical modification of the adsorbent is the chemical oxidation of pure powder chitosan using some specific redox pairs which are potassium dichromate and sodium bisulphite. After preparing the modified chitosan, there are some parameters that must be discussed during the adsorption process. The first parameter is the time parameter, showing experimentally the optimum time for adsorption under certain conditions by collecting values of absorbance and concentration of thymol blue adsorbed after the process from …

A Spin-Coated Tiox/Pt Nanolayered Anodic Catalyst For The Direct Formic Acid Fuel Cells, Islam M. Al-Akraa, Ahmad M. Mohammad Prof

Chemical Engineering

The CO poisoning of the platinum anodic catalyst which typically functions the catalytic deterioration of the direct formic acid fuel cells could be minimized with a simple modification for Pt with titanium oxide. The fabrication scheme involved the spin-coating of a Ti precursor onto a Pt thin layer that was physically sputtered onto a Si substrate. The whole assembly was subjected to a post-annealing processing to produce the TiOx layer (60 nm) in a porous structure (mostly Anatase) atop of the Pt surface. The porous nature of the TiOx layer permitted the participation of Pt in the electrocatalysis of the …

Process Data Analytics Using Deep Learning Techniques, Majid Moradi Aliabadi

Wayne State University Theses

In chemical manufacturing plants, numerous types of data are accessible, which could be process operational data (historical or real-time), process design and product quality data, economic and environmental (including process safety, waste emission and health impact) data. Effective knowledge extraction from raw data has always been a very challenging task, especially the data needed for a type of study is huge. Other characteristics of process data such as noise, dynamics, and highly correlated process parameters make this more challenging.

In this study, we introduce an attention-based RNN for multi-step-ahead prediction that can have applications in model predictive control, fault diagnosis, …

Gravity-Drawing Flexible Silicone Filaments As Fiber Optics And Model Foldamers, Katherine Snell

CMC Senior Theses

Here, we present a method of gravity-drawing polydimethylsiloxane (PDMS) silicone fibers with application as fiber optics and as model foldamers. Beginning as a viscous liquid, PDMS is cured using heat until its measured viscosity reaches 4000 mPa•s. The semi-cured elastomer is then extruded through a tube furnace to produce thin (diameters on the order of hundred micrometers) filaments with scalable lengths. PDMS is biocompatible, gas-permeable, flexible, and hydrophobic. Additionally, the PDMS surface hydrophobicity can be modified via UV exposure, O2 plasma, and corona discharge. We demonstrate the patternibility (i.e patterns of hydrophobicity) of PDMS fibers, adding complexity to potential foldamer …

Synthesis Of Graphene Using Plasma Etching And Atmospheric Pressure Annealing: Process And Sensor Development, Andrew Robert Graves

Graduate Theses, Dissertations, and Problem Reports (ETD)

Having been theorized in 1947, it was not until 2004 that graphene was first isolated. In the years since its isolation, graphene has been the subject of intense, world-wide study due to its incredibly diverse array of useful properties. Even though many billions of dollars have been spent on its development, graphene has yet to break out of the laboratory and penetrate mainstream industrial applications markets. This is because graphene faces a ‘grand challenge.’ Simply put, there is currently no method of manufacturing high-quality graphene on the industrial scale. This grand challenge looms particularly large for electronic applications where the …

Elucidating The Properties And Mechanism For Cellulose Dissolution In Tetrabutylphosphonium-Based Ionic Liquids Using High Concentrations Of Water, Brad Crawford

Graduate Theses, Dissertations, and Problem Reports (ETD)

The structural, transport, and thermodynamic properties related to cellulose dissolution by tetrabutylphosphonium chloride (TBPCl) and tetrabutylphosphonium hydroxide (TBPH)-water mixtures have been calculated via molecular dynamics simulations. For both ionic liquid (IL)-water solutions, water veins begin to form between the TBPs interlocking arms at 80 mol % water, opening a pathway for the diffusion of the anions, cations, and water. The water veins allow for a diffusion regime shift in the concentration region from 80 to 92.5 mol % water, providing a higher probability of solvent interaction with the dissolving cellulose strand. The hydrogen bonding was compared between small and large …

Design Of Pigments For Use In “Cool” Coatings, Tyler Laughorn

Williams Honors College, Honors Research Projects

This project was focused on the development and testing of several novel pigments that exhibit high NIR-reflectance and therefore show potential for use in “cool” coatings. A “cool” coating will reflect more solar radiation than other standard coatings, and so a coated structure would require less energy to keep cool. Four sets of pigments were synthesized: Co_1-xMg_xCr₂O₄ (teal), Co_0.25Mg_0.75Cr_2-yAl_yO₄ (blue), Ti_1-x-yNi_xSb_yO₂ (yellow), and Cr_2-xFe_xO₃ (black). NIR and TSR values were then measured …

Filtration Apparatus Design For Oil-Water Separation Using Membranes And Sponges, Alec Jerger

Williams Honors College, Honors Research Projects

It can be difficult to separate water and oil emulsions through traditional filtration. Therefore, investigations of filtering using thermo-responsive (TR) polymers, in this case poly(vinyl methyl ether) (PVME), was conducted. It’s hypothesized that below its lower critical solution temperature (LCST), PVME has an affinity for water while oil substances do not. Above the LCST the opposite will be true. To verify this hypothesis, iterations of filtration designs were created to provide optimum control over the parameters to measure flow. The final optimized experimental apparatus was a Chromaflex glass column which was air tight and controlled all parameters besides fluid flow. …

Using Batman Software To Analyze Metabolic Changes In Type 1 Diabetes-Susceptible Rats, Connor Hall

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Reactions At The Critical Point Of Solution, Jason Mote

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Structure, Morphology And Composition-Property Elucidation Of Ni–Mo And Ni−Mo−P Nanocrystals For Water Splitting Reactions And Group Iv Alloy And Silicate Nanocrystals For Visible To Near Ir Optoelectronics, Ebtesam Hassan Abuelenein Eladgham

Theses and Dissertations

Abstract

Structure, Morphology and Composition-Property Elucidation of Ni–Mo and Ni−Mo−P Nanocrystals for Water Splitting Reactions and Group IV Alloy and Silicate Nanocrystals for Visible to Near IR Optoelectronics

by

Ebtesam Hassan Abuelenein Eladgham

A dissertation submitted in partial fulfillment of the requirements for the degree of Doctor of Philosophy at Virginia Commonwealth University.

Advisor: Indika U Arachchige

Associate Professor, Department of Chemistry

Nanomaterials have gained a great attention because of their unique physical properties with size intermediate between molecular materials and extended solids. They have a large surface to volume ratio and display size tunable physical properties that was not …

Emulsion Stability Of Heavy Oil With Surfactants And Nanoparticles, Zainab Abdulmohsein, Baojun Bai, Parthasakha Neogi

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The recovered crude oil is often in form of an emulsion and the recovery is cut off when water to oil ratio exceeds a certain amount. The emulsions vary from water-in-oil to oil-in-water and the step that follows is to coalesce droplets to get two continuous liquids. Difficulties arise when the oil contains emulsifiers. There are naturally occurring surfactants, or the oil recovered is by enhanced oil recovery techniques which have additives that stabilize the droplets. We have considered below a heavy oil (viscosity 650-750 mPa.s) containing one of the three surfactants: a nonionic surfactant or a cationic surfactant or …

Analysis Of Mass Transfer Coefficient Of Co2 Absorbed By Two-Component Amine Mixture In A Packed Bed Column, Thanakornkan Limlertchareonwanit

Chulalongkorn University Theses and Dissertations (Chula ETD)

Nowadays, coal fired plant has an important role in generating energy all over the world. It affects to greenhouse gases effect (GHGs) and global warming. Carbon dioxide (CO2) is a product of coal combustion that is the amount of number one in the world. However, most of the CO2 usually remove from post-combustion process by chemical absorption which is Monoethanolamine (MEA). Anyway, MEA has a disadvantage such as low CO2 loading and corrosion. Therefore, this study needs to investigate the effect of the mass transfer for a new solvents, 2-(Methylamino)ethanol (2-MAE) and Dimethylaminoethanol (DMAE), compensate for the drawbacks of MEA …

Effect Of Cocatalyst Combination In Titanium-Based Ziegler-Natta Catalyst On Olefin Polymerization, Thanyaporn Pongchan

Chulalongkorn University Theses and Dissertations (Chula ETD)

This research focused on effect of cocatalyst types (TEA, TnOA, and TEA+TnOA) on titanium-based Ziegler-Natta catalyst in olefin polymerization both in slurry and gas-phase systems. This study has been divided into four sections. The commercial titanium-based catalyst was selected to investigate effect of reaction temperature and oxidation state of titanium from ESR measurement on slurry ethylene and propylene polymerization in the first and the second parts, respectively. The commercial catalyst with TEA exhibited the highest activity in ethylene polymerization. However, divalent, and trivalent of titanium (Ti2+ and Ti3+) was active in ethylene polymerization to produce more polymer. Stability of Ti3+ …

Development Of Graphite-Based Conductive Patterns By Copper Electroless Plating And Electroplating Techniques, Vipada Aupama

Chulalongkorn University Theses and Dissertations (Chula ETD)

The screen-printing technique has been widely applied in electronic manufacturing field. In this work, graphite is used for fabricating conductive patterns by screen-printing technique. Moreover, enhance the performance of electrical conductivity by electroless plating and electroplating techniques. The study was separated into two parts. Firstly, optimize the mass ratio between graphite and polyvinylidene fluoride (PVDF). In prepared ink from varied mass ratio; 2.0:0.1, 2:0.2, and 2:0.3 respectively. Volume resistivity analysis of conductive patterns, it was found that the mass ratio between graphite and PVDF of 2: 0.2 provided the lowest volume resistivity of 0.0122 Ω-m. In other cases, the mass …

Study Of Interactions Between Magnesium Silicate Particle And Diamond-Like Carbon Using Atomic Force Microscopy, Vipada Dokmai

Chulalongkorn University Theses and Dissertations (Chula ETD)

Interaction between particles and different surfaces under ambient condition is studied using AFM-based force spectroscopy. This work focuses on the adhesion mechanism and factors affecting particle-surface adhesion. The particles of interest consist of magnesium silicate (talcum powder) and zinc oxide (ZnO) particles, which have very attractive properties and are widely used in several applications. The adhesion force measurements were first carried out using silicon/silicon coated with DLC probes pressed on talc particles modified with hydrochloric acid or different organosilanes. These modifications change hydrophobicity and hydrophilicity of the particles. The results show that the adhesion forces are distributed in a bimodal …

Fundamental Study Of Supported Metal Catalysts Prepared By Metal In Lithium Solution For Energy Science, Haiping Xu

Graduate Research Theses & Dissertations

Electrochemical carbon dioxide reduction reaction (CO2RR) is a promising technique for energy conversion and storage from intermittent electricity sources (ie. wind and solar). By coupling electrochemical CO2 reduction (CO2R) to a renewable energy source atmospheric CO2 could be converted back into a fuel such as ethanol, or a commodity chemical such as ethanol or acetic acid. These products could then be consumed for energy or used to generate more valuable chemical products effectively removing CO2 from the atmosphere. To commercialize this process, it is highly desired to prepare catalysts that selectively reduce CO2 at low overpotential with long durability. Research …

Time-Dependent Reliability Framework For Durability Design Of Frp Composites, Rajneesh Kumar Bharil

Graduate Theses, Dissertations, and Problem Reports (ETD)

The life-cycle performance, durability, and aging characteristics of Fiber Reinforced Polymer (FRP or Structural Composites) have been of keen interest to the engineers engaged in the FRP design, construction, and manufacturing. Unlike conventional construction materials such as steel and concrete, the design guidelines to account for the aging of FRP are somewhat scattered or not available in an approved or consistent format. Loss of strength over time or aging of any structural material should be of concern to engineers as the in-service lifespan of many engineering structures is expected to exceed 100 years. Use of durability strength-reduction factors or factors …

An Integrated Wellbore Stability Study To Mitigate Expensive Wellbore Instability Problems While Drilling Into Zubair Shale/Sand Sequence, Southern Iraq, Ahmed Khudhair Abbas

Doctoral Dissertations

”The Zubair Formation is the most prolific reservoir in Iraq, which is comprised of sandstones interbedded with shale sequences. Due to the weak nature of the shale sequence, the instability of a wellbore is one of the most critical challenges that continuously appears during drilling across this formation. Historically, over 90% of wellbore problems in the Zubair Formation were due to wellbore instability. Problems associated with wellbore instability, such as tight hole, shale caving, stuck logging tools along with subsequent fishing, stuck pipe, and sidetracking result in increasing the non-productive time. This non-productive time has cost an enormous amount of …

Ni-Au Anodic Nano-Electrocatalyst For Direct Glucose Fuel Cells, Islam M. Al-Akraa, Aya S. Abdulhalim Eng, Yassr M. Asal Mr, Ahmad M. Mohammad Prof

Chemical Engineering

This study aims at the sequential assembling of a nickel oxide (NiOx: cauliflower-like nanostructure, 90 nm) and gold (Au; spherical, 95 nm in an average particle size) onto the GC surface nanocatalyst on a glassy carbon (GC) electrode (will be abbreviated as Ni-Au/GC) for the glucose electro−oxidation (GO); the principal anodic reaction in the direct glucose fuel cells (DGFCs). The charge of the Ni deposition on the GC surface (will be abbreviated as Ni/GC electrode) was initially optimized to obtain the highest catalytic activity toward GO which attained at (339.8 Ag−1) by applying 15 mC in the Ni deposition. Yet, …

Structural Analysis Of Deformed Caprock Associated With A Salt Shoulder At Gypsum Valley Salt Wall, Paradox Basin, Colorado, Hanah Draper

Open Access Theses & Dissertations

This study documents the style and distribution of deformation present in Triassic-age gypsic and carbonate caprock associated with the Gypsum Valley Salt Wall Salt Shoulder in the Paradox Basin, Colorado in order to determine the mechanism and timing of deformation. Mapping of gypsic and carbonate capstone facies shows that the caprock layering that was generated during formation has been deformed by large-and-small-scale folding and faulting, brecciation, and boudinage. Deformation within the caprock resulted in widely variable orientations along the length of the salt shoulder, that also varies locally in intensity of deformation and with proximity to the passively rising diapir …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Transient Electrochemical Surface-Enhanced Raman Spectroscopic Study In Electrochemical Reduction Of P-Nitrothiophenol, Yun Ling, Jing Tang, Guo-Kun Liu, Cheng Zong

Journal of Electrochemistry

P-nitrothiophenol (PNTP) is one of the most common probe molecules studied by surface-enhanced Raman spectroscopy (SERS). The research in electrochemical reduction behavior of PNTP will help understanding the mechanism for the nitrobenzene reduction. In this paper, we used transient electrochemical surface-enhanced Raman spectroscopy (TEC-SERS) to study the SERS of PNTP with cyclic voltammetry and chronoamperometry on gold electrodes. The results show that the TEC-SERS provide a time resolution that equals the transient electrochemical methods, and we concluded that the reaction was so quick that we did not observe the spectral information of intermediate species described in the literatures with a …

Zif-67-Derived Ag/Co-Embedded N-Enriched Mesoporous Carbon For Oxygen Reduction Reaction, Zheng-Ling Di, Jing Zhu, Lei Dai, Wei Meng, Yue-Hua Li, Zhang-Xing He, Ling Wang

Journal of Electrochemistry

Nitrogen-doped porous carbon materials are considered as one of the most promising catalysts for oxygen reduction reaction (ORR). Herein, in order to further improve the activity of the nitrogen-doped porous carbon, Ag/Co bimetal is embedded into nitrogendoped porous carbon to form Ag/Co-embedded nitrogen-doped porous carbon material (AgCo@NC). The AgCo@NC was derived by the wet impregnation of Ag+ into ZIF-67 precursor, followed by chemical reduction and a subsequent pyrolysis process under Ar atmosphere at different temperatures (500 ℃, 600 ℃, 700 ℃). The morphologic characterization shows that the Ag/Co nanoparticles were successfully embedded in the mesoporous carbon framework with abundant nitrogen …

Ionic Liquid Assisted Synthesis Of Porous Carbons From Rice Husk For Supercapacitors, Han-Fang Zhang, Feng Wei, Jian Sun, Meng-Ying Jing, Xiao-Jun He

Journal of Electrochemistry

It is still a challenge to prepare carbon materials with high specific surface area at low cost from renewable resources. Herein, the authors report an efficient approach to synthesize porous carbons (PCs) from rice husk with ionic liquid (1-butyl-3-methylimidazolium hexafluorophosphate (BMIMPF₆)) as a template and an activation agent. The as-made PCs featured the high specific surface area up to 1438 m²·g^-1. As electrodes for supercapacitors, PCs showed a high specific capacitance of 256 F·g^-1 at 0.05 A·g^-1 in 6 mol·L^-1 KOH aqueous electrolyte and a good rate performance of 211 F·g …

Electrochemical Sensor Based On Magnetic Electrode Modified With Magnetic Molecularly Imprinted Nanoparticles Immobilized Hemoglobin For Determination Of Hydrogen Peroxide, Yang Yuan, Jia-Xin Wang, Yu-Hua Cao

Journal of Electrochemistry

In this work, the surface-imprinted technique was used to prepare magnetic hemoglobin (Hb) imprinted nanoparticles, using Fe₃O₄@SiO₂ NPs as the carrier, Hb as the template molecule, and tetraethyl orthosilicate (TEOS) as the imprinted polymer monomer. The nanoparticles had a core-shell structure, with magnetic Fe₃O₄ NPs as the core and Hb imprinted polymers as the shell. Therefore, Hb could be concentrated and fixed on the surface of the magnetic imprinted nanoparticles (MMIPs NPs). Furthermore, MMIPs NPs were immobilized with chitosan (CS) on the surface of a magnetic electrode to constitute Hb enzyme-like biosensor …

A Microfluidic Paper-Based Analytical Device For Early Diagnosis And Prognosis Of Acute Myocardial Infarction, Lim Wei Yin

Student Works (2020-2029)

Acute myocardial infarction (AMI), also termed as heart attack, is often clinically screened by blood test through the measurement of cardiac biomarkers (i.e., troponin (T or I), creatine kinase (CK−MB) and myoglobin) and electrocardiography (ECG) changes which are presented to the hospital. However, the early diagnosis of AMI is challenging because the detection of biomarkers such as troponin (T or I) and CK−MB are only reliable at the intermediate and later stages (> 6 hours after chest pain onset), during myocardial injury and myocardial infarction. On the other hand, myoglobin often been used as early biomarker which is detectable within …

Low Temperature Liquid Metal Batteries For Energy Storage Applications, Cameron A. Lippert, Kunlei Liu, James Landon, Susan A. Odom, Nicolas E. Holubowitch

Center for Applied Energy Research Faculty Patents

The present invention relates to a molten metal battery of liquid bismuth and liquid tin electrodes and a eutectic electrolyte. The electrodes may be coaxial and coplanar. The eutectic electrolyte may be in contact with a surface of each electrode. The eutectic electrolyte may comprise ZnC1₂:KCI.

The Role Of Multi-Charged Responses: Construction And Application Of A Tandem Differential Mobility Analyzer (Tdma), Christopher Ray Oxford

McKelvey School of Engineering Graduate Student Theses & Dissertations

Atmospheric aerosols impact health outcomes, visibility, and the energy balance of the earth. The atmosphere contains a variety of compounds, and the volatility (phase change enthalpy and vapor pressure) of each compound determines its partitioning between the gas phase and the particle phase. The hygroscopicity (an aerosol’s affinity for water) of an atmospheric aerosol particle is determined by the many compounds present in the particle, and thus, the volatility impacts hygroscopicity. Changes in hygroscopicity alter the fraction of the aerosol deposited in the lungs and the fraction of the aerosol activated into cloud droplets. Thus, understanding the volatility and hygroscopicity …

Contemporary Problems In Aerosol Aggregation And Gelation, Pai Liu

McKelvey School of Engineering Graduate Student Theses & Dissertations

Aggregation of nanoparticles in aerosols is a fundamental phenomenon with important implications to diverse fields ranging from material synthesis to pollutant control. The past few decades have witnessed extensive research on investigating the structure and growth mechanism of aerosol aggregates with sizes spanning across several orders of magnitude. This dissertation focuses on some contemporary problems that remain unaddressed in this topical area. Aerosol aggregates in sub-micron regimes, which are formed via the irreversible collision and aggregation of solid nanoparticle monomers, are fractal-like in their morphology. A mathematical description of this seemingly random structure dates to the seminal works by Forest …