Chemical Engineering Commons^™

Electrocatalytic Oxidation Of Formaldehyde On The Proline Film Modified Electrode, Yu-Rong Ma, Qiu-Xia Yang, Guo-Bao Li, Zheng-Kai Xi, Xue-Lin Wang

Journal of Electrochemistry

The proline film modified electrode and its electrochemical behavior was studied by cyclic voltammetry and spectroelectrochemistry. After incorporation of Ni(Ⅱ), the cyclic voltammograms of the proline Ni(Ⅱ) film electrode exhibited a typical redox peak, which appeared at potential of 0.52 V anodic and 0.44 V cathodic in NaOH. The formal potentials E' were linearly dependent on the pH, and the peak currents ip were linearly dependent on the square root of the scan rates, thus charge transfer in the film was controlled by diffusion. The diffusion coefficient is figured out to be 2×10^_-10 cm²·s^-1. The …

Preparation,Structure And Properties Of Electrochromic Rhodium Oxide Films, Hai-Hong Wang, Tao Wang, Man-Ming Yan, Zhi-Yu Jiang

Journal of Electrochemistry

Electrochromic rhodium oxide films were prepared on ITO substrate by sol-gel method. The films exhibited reversible two-color (bright yellow at reduction and dark green at oxidation) electrochromic behavior in alkaline solution with good cycle stability. In-situ XRD, TGA-DTA, IR, XPS methods were used for studying the structure and chemical process of the films. The diffusion coefficient during the electrochromic process was measured by electrochemical impedance spectra method. It was found that the rhodium oxide films may be suitable for the use in electrochromic devices.

The Fission Properties Of Curium Separated From Spent Nuclear Fuel, William Culbreth, Elizabeth Bakker, Jason Viggato

Separations Campaign (TRP)

Curium poses special problems in the chemical preparation of spent nuclear fuel for transmutation. Once separated from the other minor actinides, the seven curium isotopes in spent fuel can lead to nuclear fission with the subsequent release of a large amount of radiation. Several isotopes of curium also generate a significant amount of heat by radioactive decay. Sustained fission can be avoided by preventing the accumulation by more that a critical mass of curium. The heat generation of curium presents even more restriction on the mass of curium that can safely be contained in one location.

To analyze the nuclear …

Modeling And Experimental Verification Of Growth Of An Axisymmetric Cylindrical Rod By Three-Dimensional Laser-Induced Chemical Vapor Deposition, Qing Chen

Doctoral Dissertations

Three-dimensional laser-induced chemical vapor deposition (3D-LCVD) is a recently developed micro-manufacturing process that holds great potential for the production of complex microstructures with high aspect ratio. A laser beam is focused through a vacuum chamber window onto a movable substrate. The heat from the laser at or near the focal spot on the substrate induces the decomposition reaction of precursor gas in the chamber. As a result, solid-phase reaction products are deposited on the substrate to form the microstructure. In this dissertation, a numerical model is developed for simulating kinetically-limited growth of an axisymmetric cylindrical rod by pre-specifying the surface …

Preliminary Study On Direct Ethanol Fuel Cell, Shu-Qin Song, Li-Kang Chen, Jian-Guo Liu, Zhao-Bin Wei, Qin Xin

Journal of Electrochemistry

The performance of a direct ethanol fuel cell based on Nafion115 was reported.PtRu/C and Pt/C were used as ethanol anode and oxygen cathode catalysts in a single cell of size 9 cm² .The effects of temperature, oxygen pressure, the flow rate of ethanol, and oxygen, and ethanol concentration were tentatively studied. The experimental results showed that the cell open circuit voltage 0.608 V, the cell voltage 0.329 V at 50 mA/cm², and the peak power density 19.25 mW/cm² were reached under the conditions of T_cell =85 ℃, P_O2 =0.5 MPa, C_ethanol =1.0 mol/L …

Electrosynthesis Of Glyoxylic Acid In A Packed Bed Reactor, Jin-Hong Fan, Jun Li, Yu-Zhong Su, Hao-Qi Gao

Journal of Electrochemistry

Glyoxylic acid was produced by electroreduction of oxalic acid in a packed bed reator. The cathodic and anodic electrolytes were super-saturated oxalic and hydrochloric acid aqueous solutions separated by a super-acid ion-exchange membrane. The current efficiency and yield of glyoxylic acid were studied under different structured packed bed reactors and different electrode materials, temperatures and current densities. The results indicated that the current efficiency of synthsis of glyoxylic acid was over 66.2% and the concentration of glyoxylic acid could reach 2.02% after 45min electrolysis with cathode of lead particles and anode of graphite board under conditions of temperature 32 ℃, …

Varying Current Electro-Synthesis Of Glyoxalic Acid In Pairs In The Fixed-Bed Electrolytic Cell, Yin-Sheng Chen, Xin-Sheng Zhang, Ying-Chun Dai, Wei-Kang Yuan

Journal of Electrochemistry

As for the process of the electro oxidation of glyoxal to glyoxalic acid, the electrolytic result of either fixed bed electrolytic cell or varying current electrolysis was better than that of either flat plate electrolytic cell or constant current electrolysis. The average current density of varying current electro synthesis of glyoxalic acid in pairs was 1535 A/m² and the current efficiency were 85.3% and 86.7% and the selectivity were 93.9% and 94.0% for the anodic oxidation and cathodal reduction respectively. The initial composition of anodic electrolyte was 7% glyoxal and 8% hydrochloric acid (W/W) and the cathodal electrolyte consisted …

Electrochemical Synthesis And Characterization Of The Nickel Electropolyurushiol Coordination Polymer, Feng Gao, Guo-Cai Shen, Jie-Yuan Tang, Wen-Gong Zhang

Journal of Electrochemistry

The nickel electropolyurushiol coordination polymer (EPU Ni²⁺) was obtained by the reaction between nickel chloride isopropyl alcohol solution with electropolyurushiol (EPU). The electrochemical polymerization of urushiol and the preparation of nickel electropolyurushiol coordination polymer were investigated. The coordination polymer was characterized by XPS, FT-IR, DMTA and AES methods, and its composition and structure were determined.The content of Ni²⁺ reached up to 7.5%. It was shown that there was certain coordination between Ni²⁺ and electropolyurushiol in the coordination polymer, thus cross-inks were formed. Therefore the glass transition temperature of the coordination polymer increased and heat resistance was …

Membrane Ultrafiltration Of Treated Palm Oil Mill Effluent (Pome), Pui Wah Wong

Student Works (2000-2009)

The common practice for treatment of palm oil effluent (POME) in Malaysia employs a combination of aerobic and an anaerobic treatment. Bearing in mind that the quantity of POME produced is high, reaching 740 000 m3 in May 2001, reuse and recycling of treated POME can be an excellent practice in terms of saving of water resources. As the treated POME is already low in certain parameters required by the Department of Environment (i.e. BOD, total and ammoniacal nitrogen, oil and grease), further treatment will greatly enhance the water quality. The purpose of the advance treatment step is to allow …

Biological Reduction Of Perchlorate In Ion Exchange Regenerant Solutions Containing High Salinity And Ammonium Levels, Tina M. Gingras, Jacimaria R. Batista

Civil and Environmental Engineering and Construction Faculty Research

The most promising technologies to remove perchlorate from water are ion exchange and biological reduction. Although successful, ion exchange only separates perchlorate from water; it does not eliminate it from the environment. The waste streams from these systems contain the caustic or saline regenerant solutions used in the process as well as high levels of perchlorate. Biological reduction could be used to treat the regenerant waste solutions from the ion exchange process. A treatment scheme, combining ion exchange and biodegradation, is proposed to completely remove perchlorate from the environment. Perchlorate-laden resins generate brines containing salt concentrations up to 6% or …

Compostability Of Degradable Plastics And Its Use In Solid Waste Disposal / Putri Nadzrul Faizura Bt Megat Khamaruddin., Putri Nadzrul Faizura Megat Khamaruddin

Student Works (2000-2009)

Plastic waste generation and quantity generated is a growing concern in many countries including Malaysia. Plastic waste contributes the third highest waste volume in Malaysian municipal solid waste (MSW) next to putrescible waste and paper. ln the year 2000, plastic waste in MSW of Kuala Lumpur was 24.4% by weight from the MSW and most of the plastic waste was dumped into landfills. Landfills in Malaysia are reducing in its useful life as the amount of waste generated is growing every year by 2% and they have become an undesirable option of getting rid of plastic waste because of the …

Electrosynthesis Of A New Electroactive Poly(2,2'-Diaminophenyloxydisulfide), Yu-Zhi Su, Yan-Wen Rao, Ye Yang, Mei-Bing Chen, Yin-Ling Qiu, Yong-Hua Zhang, Ke-Cheng Gong

Journal of Electrochemistry

A new electroactive poly (2,2' diaminophenyloxydisulfide) (PDAPD) was successfully synthesized from acetonitrile(AN)/tetrahydrofuran (THF) solutions containing the supporting electrolyte (LiClO₄) and the various kinds of acids (HCl, CF₃COOH, CCl₃COOH) on Pt electrode by consecutive cyclic voltammiry. The effects of the concentrations of supporting electrolyte (LiClO₄) and acid (HCl, CF₃COOH, CCl₃COOH) on electrodepositon of PDAPD film were investigated. The best experimental conditions for electrosynthesis of a highly electroactive conducting polymer film are that the concentrations are 0.1 mol/L and between 0.05 mol/L～0.5 mol/L,respectively for LiClO₄ and HCl.

Research Progress On Proton Exchange Membranes Of Fuel Cells, Jing-Rong Yu, Dan-Min Xing, Fu-Qiang Liu, Jian-Guo Liu, Bao-Lian Yi

Journal of Electrochemistry

The proton exchange membrane fuel cells (PEMFC) use proton exchange membranes(PEM) as their electrolytes. The performance of the PEMFC is strongly dependent on the characteristics of the PEM. In this paper, the requirements of the PEM utilized in the PEMFC were analyzed. The per-fluorinated, partially fluorinated and non-fluorinated PEM were introduced respectively. The structures, preparation, properties of the various types of PEM and their applications in the PEMFC were also discussed in detail.

The Influence Of Synthesis Conditions On The Electrochemical Properties Of Spinel Limn2O4, Jun-Feng Xu, Zhi-Yu Jiang

Journal of Electrochemistry

The electrochemical properties of spine LiMn₂O₄ synthesized via a solid state reaction were investigated. Electrolysis MnO₂(EMD), Li₂CO₃ ,LiOH and LiNO₃ were used as the initial materials. It was found that the electrochemical properties of LiMn₂O₄ were strongly influenced by the synthesis conditions. The LiMn₂O₄ sample sprepared via the reactionof EMD and LiNO₃ showed the best properties for a lithiumion intercalation reaction. The procedure includes two steps:pretreatment at 280 ℃ for 6 hours to initiate the permeation of melting LiNO₃ into the microporesof EMD …

Adsorption And Oxidation Of Methanol On Pt And Sb, S Modified Pt Electrodes Using Cyclic Voltammetry And Eqcm, Guo-Liang Chen, Sheng-Pei Chen, Heng Lin, Xing-Hong Zheng, Shi-Gang Sun

Journal of Electrochemistry

The processes of adsorption and oxidation of methanol on Pt, Pt/Sb ad and Pt/S ad electrodes were studied by using cyclic voltammetry and electrochemical quartz crystal microbalance (EQCM). The results demonstrated that the oxidation of methanol depends strongly on oxidation states of electrode surface. Sb adatoms on Pt surface can adsorb oxygen at relatively low potentials, and exhibit catalytic effects for methanol oxidation. In contrast to Pt electrodes, the oxidation peak potential of methanol in this case negatively shifted to about 130 mV. In a contrary, the oxidation of S_ad atoms consumes oxygen species of Pt electrode surface. As …

Electrokinetic Cha Raci'erisation Of Colloidal A-Alumina, J Ntalikwa

Tanzania Journal of Engineering and Technology (TJET)

Electrophoretic mobility (uD is an important rneasurable parameter in studying the electrokinetic properties of a colloid dispersion. This parameter is Often convened into zeta potential (C) Which piays a great role in thc description Of the stability towards aggregation Of dispersed particles. In this paper, measurements of Of colloidal a-alumina dispersed in various concentrations of electrolyte arc reported. It was observed that, the isoelectric points (the pH at which us = O) occurred at 7.52 ± 0.32, 8.05 ± 0.11 and 7,95 ± 0.18 in Naci, KCI and NaNOs respectively. The isoelectric point was observed to be a function Of …

Comparative Analysis Of Rng K-E And 'Standard' K-C Models For Fluid Flow Around A Cylinder, A Temu

Tanzania Journal of Engineering and Technology (TJET)

A two-dimensional computational scheme for simulating fluid flow around a cylinder was investigated. RNG (Re-NOrmalisation Group) and 'standard' turbulent closure models were used. simulation was implemented with assistance OfFLOW-3D computational fluid dynamics (CFD) code. The governing equation Of fluid motion, in Eulerian form, included body forces as well as surface forces. The computational model predictions for fluid velocity showed good agreement between the two models. Comparison Of the viscosities showed a large deviation from the two models, with RNG k-E model giving a better approximation. Comparison Of the velocity around the cylinder, as obtained from RNG k-c model, with approximation …

Performance Of Proton Exchange Membranefuel Cell With Co/H2 Fuel, Hong-Mei Yu, Zhong-Jun Hou, Bao-Lian Yi, Ke-Wan Bi, Jing-Xin Zhang, Zhi-Yin Lin, Ming Han

Journal of Electrochemistry

Fuel of proton exchange membrane fuel cell(PEMFC) mostly comes from reformatecontains CO which will poison the fuel cell electrocatalyst. The effect of CO on the performance of PEMFC was studied in this paper. The results of the experiment show that when CO is fed inPEMFC ,the cell voltage will be decreased violently,then it will become steady with some vibration. The poison will become more serious with higher CO content and weaker at higher temperature. The adsorption of CO on the electrocatalyst is reversible. The PtRu electrocatalyst is moresuitable for the electrocatalysis of CO/H₂ than Pt electrocatalyst.

Study Of The Oxidation Dynamics Of Tizro2 Metal-Ceramics, Wen-Chao Li, Li-Dong Teng

Journal of Electrochemistry

The oxidation dynamics of hot-pressed Ti-ZrO₂ metal-ceramics with the compositionof 50 vol.% Ti and 50 vol.% ZrO₂ has been studied.Thermodynamic analysis shows that Ticould react with O₂ but not with N₂ in the oxidizing process of TiZrO₂ composites at 0.1 MPa air. The oxidation dynamic behavior of Ti-ZrO₂ composites is analogous to that of pure Ti. Theactivation energy for the oxygen diffusion in Ti-ZrO₂ composites is higher than that in Ti solutions, for the presence of ZrO₂ restrains the oxygen diffusion in Ti-ZrO₂ composites. At early stagethe oxidation of Ti-ZrO_{2 …}

Performance Of A Direct Methanol Fuel Cell, Zhao-Bin Wei, Jian-Guo Liu, Ya-Guang Jiao, Wei-Jiang Zhou, Wen-Zhen Li, Li-Kang Chen, Qin Xin, Bao-Lian Yi

Journal of Electrochemistry

A direct methanol fuel cell with 9cm² active area consists of Pt-Ru/C anode ,Pt/Ccathode and Nafion 115 membrane. The effect of operating conditions: methanol solution concentration, oxygen pressure and cell temperature on the cell performances was investigated. The results show that performance of single cell was enhanced by increasing oxygen pressure and celltemperature ,and a maximum power density 75 mW/cm² was obtained in the range of 250-300mA/cm² current density, 0.2 MPa oxygen pressure, 1.0 mol/L methanol concentration and 75 ℃ cell temperature. When cell operating at room temperature, a relatively low, but a stable performance of cell …

New Progress In Studies Of Lithium Nickel Oxide As Positive Electrode Materials Of Lithium Ion Batteris, Han-San Liu, Yong Yang, Zhong-Ru Zhang, Zu-Geng Lin

Journal of Electrochemistry

Lithium nickel oxide as the positive electrode of lithium ion batteries has aroused more and more interests.This paper reviews the recent reserches on synthesis and element-substitution of LiNiO₂ cathode material,and summarizes the intrinsical relationship between properties and sturcture of the material.The developments of new synthesis methods and mutilsubstitution of the material are expecting to be studied in the future research.

Effects Of Concentration And Temperature On The Coupled Heat And Mass Transport In Liquid Mixtures, Yaşar Demirel, Stanley I. Sandler

Papers in Thermal Mechanics

Using published experimental data on the thermal conductivity, mutual diffusivity, and heats of transport, the degree of coupling between heat and mass flows has been calculated for binary and ternary nonideal liquid mixtures. The binary mixtures consist of two types: the first is six systems of six-to-eight-carbon straight and branched chain alkanes in chloroform and in carbon tetrachloride; and the second is mixtures of carbon tetrachloride with benzene, toluene, 2-propanone, n-hexane, and 11-octane. The ternary mixture considered is toluene-chlorobenzene-bromobenzene. The published data are available at 35°C, 30°C, and 35°C and ambient pressure. Using the linear nonequilibi-ium thermodynainics (LNET) and the …

A Study On The Performance Of Matrix Prepared By Tape Cast And Its Molten Carbonate Fuel Cells (Mcfcs), Hua-Xin Lin, Bao-Lian Yi, Li Zhou, Chang-Qing He, Lian-Ying Kong, En-Jun Zhang

Journal of Electrochemistry

The matrix prepared with γ-LiAlO₂ powder and by tape cast displayed higher ability of preventing from gas cross over and lower ohmic polarization. The voltages of the stack (three cells, 122 cm²) stacked with the matrix were 2.02 and 1.78 V at 200 and 246 mA/cm², respectively, and the output power reached 53.4 W. The cell (28 cm ²) voltages were 0.85 and 0.75 V at 200 and 300 mA/cm², respectively, and the output power was about 6.6 W. Compensating the shrinkage of matrix in stacking cells promoted the enhancement of the …

The Charge Transfer Effect Of Sers Induced By The Electrochemical Hydrogen Evolution Reaction, Feng-Ming Liu, Qi Han, Yan-Xia Chen, Qi-Ling Zhong, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

As one of the important mechanisms of SERS, the charge transfer (CT) enhancement requires the strong interaction of the adsorbed species with the substrate in order to permit the transition of charge between the metal Fermi level (energy state) and the molecular orbital. The high enhancement needs the match of the energy gap between the Fermi level (or surface state) and the orbital energy level of the adsorbed molecules with the energy of the incident light. The electrode Fermi level is usually adjusted by the applied potential to satisfy the CT resonance. For the electrochemical reaction process, the frontier orbital …

How Can Direct Mthanol Fuel Cell Benefit From Carbonate Media, Lin Zhuang, Yang Wang, Jun-Tao Lu

Journal of Electrochemistry

The kinetics of methanol oxidation and oxygen reduction in 0.5 mol/L K₂CO₃ were compared with those in 0.5 mol/L H₂SO ₄. Experiments revealed that carbonate media could be more beneficial to direct methanol fuel cell(DMFC). Firstly, both electrode reactions show better performance in the carbonate than in the acid; secondly, materials other than noble metals become possible to be used as the anodic and cathodic catalysts; thirdly, the potential dectease caused by methanol crossover could be depressed by using metal oxide catalysts not stable in acid, such as MnO₂.

Synthesis Of Limn2O4-ΔClΔ Cathode Material By Like-Sol-Gel Methode, Zhao-Yong Chen, Yi He, Xing-Quan Liu, Zhi-Jie Li, Zuo-Long Yu

Journal of Electrochemistry

LiMn₂O_4-δCl_δ was synthesized by like sol gel methode, with calculated LiOH·H₂O, Mn(No₃)₂⋅6H₂O and LiCl·H₂O, and made electrochemical test with these compounds as positive materials. Result demostrated that LiMn₂O_4-δCl_δ cathode material has exellent stability and nearly no capacity loss after reaching stability.

Adsorption And Oxidation Of Ethanol On Nm-Pt/Gc Electrode Ii. Eqcm And In-Situ Ftir Spectroscopic Studies In Acid Media, Guo-Liang Chen, Sheng-Pei Chen, Zhi-You Zhou, Chun-Hua Zhen, Shi-Gang Sun

Journal of Electrochemistry

The adsorption and oxidation of ethanol on nm Pt/GC electrode in acid solutions containing 0.1 mol·L ^-1 H₂SO₄ +0.1 mol·L ^-1 CH₃CH₂OH was investigated by using cyclic voltammetry, EQCM and in situ FTIR spectroscopy. The experimental results demonstrated that the oxidation of CH₃CH₂OH is closely relaed to solution acidity and oxygen species on electrode surface; CH₃CH₂OH was oxidized on nm Pt/GC electrode in acidic media via a dual path reaction mechanism, i.e . CH₃CH₂OH may be oxidized into CO₂ through …

Effects Of External Electric Field On The Interfacial Properties Of Weakly Dipolar Fluid, V. B. Warshavsky, T. V. Bykov, Xiao Cheng Zeng

Xiao Cheng Zeng Publications

In the framework of modified mean-field density-functional theory, effects of a uniform electric field on the interfacial properties of a model dipolar fluid are studied. Both density and orientational order-parameter profiles of the planar vapor-liquid interface are obtained as a function of the field strength. For the dipolar fluids with reduced dipole moment μ₀^*0^*E*/T*!1) can shift the surface tension by few percent. We also find that the electric field actually reduces the thermodynamical surface tension but enhances the mechanical surface tension at the equimolar dividing surface. To detect these field effects on …

Waste Management In Palm-Oleo Sdn. Bhd, Ramesh Ramasamy

Student Works (2000-2009)

Oleochemical industry in Malaysia has been diversifying significantly due to the availability of raw materials (palm oil) and the high demand for downstream products such as fatty acids, fatty alcohols and glycerine. The growth of oleochemical industries is further enhanced by fluctuations io petroleum price and regular animal diseases, which made tallow-based fats unreliable. Environmental awareness is growing rapidly in Malaysia. There is growing realization of the need to balance industrial and economic development with environmental preservation and protection, as well as, with efficient use of energy sources in order to achieve sustainable development. Extensive waste management studies were focused …

Comparative Performance Of Wastewater Treatment Plants In Three Rubber Glove Manufacturing Plants, Lee Kuan Loh

Student Works (2000-2009)

During the manufacturing of rubber gloves, water is used as wash water at different stages to clean the rubber gloves, thus generating quite a substantial amount of effluent. There are four main sources of effluent. i.e. a) from the glove formers cleaning tank, which collects the acidified water used to clean these formers, b) latex dipping tank, where it collects wash water used to cool the tank during dipping process and the sludge form the tank itself, c) leaching tank, where it collects wash water used to leach out the pollutants from the gloves and lastly d) latex compounding, containing …