Chemical Engineering Commons^™

Synthesis Of Pani/Nihcf Nanocomposite Particles And Eqcm Measurement Of Ion Exchange Properties In Solutions Containing Cd2+, Yu-Jiao Yang, Xiao-Gang Hao, Xu-Li Ma, Zhong-De Wang, Zhong-Lin Zhang, Nian-Chen Han

Journal of Electrochemistry

The PANI/NiHCF nanocomposite particles were synthesized on the CNTs-modified Pt substrate by one-step co-polymerization using cyclic voltammetry. Electrochemical quartz crystal microbalance (EQCM) technique was adopted to investigate the polymerization process of the nanocomposite particles and the mechanism of ion exchange in aqueous solution containing Cd²⁺． The morphology and structure of the as-prepared composite particles were characterized by scanning electron microscope (SEM), transmission electron microscope (TEM), and Fourier transform infrared spectroscopy (FT-IR). Combined with cyclic voltammetry (CV) and energy dispersive spectroscopy (EDS), the electrochemical behavior and the mechanism of ion exchange were also investigated in electrolytes of Cd^{2+ …}

A Comparative Study In Pretreatments Of Acid Chemical Wastewater By Electrochemical Oxidation And Ozonation, Han-Shui Liu, Su Yu, Shao-Ping Tong, Chun-An Ma

Journal of Electrochemistry

Under the condition of keeping certain acidity, the pretreatment efficiency of an acid chemical wastewater (pH 0.85) by electrochemical oxidation was compared with that by ozonation. The results showed that the electrochemical oxidation pretreatment could obtain a better result than the ozonation at pH 0.85. After the addition of 2 g·L^-1 NaCl and with the electrochemical oxidation pretreatment at 30 mA·cm^-2, the removal rate of chemical oxygen demand (CODCr) reached 43.4%, and the value of biochemical oxygen demand/chemical oxygen demand (BOD₅/COD_Cr) also increased from 0.034 to 0.14 in 20 minutes, indicating significantly improvement …

Preparation Of Benzoquinone From Phenol By Electrooxidation, Dong-Fang Niu, Cheng-Kai Yu, Xin-Sheng Zhang

Journal of Electrochemistry

The benzoquinone was prepared from phenol by electrooxidation in an H-type cell with cation exchange membrane, in which lead plates were used both as an anode and a cathode, while H₂SO₄ was used as a supporting electrolyte. The effects of current density, concentration of sulphuric acid, concentrations of benzoquinone in electrolyte and extractant on the yields and efficiencies of electrolysis were investigated. Under the optimized conditions of current density being 4 A·dm^-2, concentration of sulphuric acid 1 mol·L^-1, passed charge 3.2 A·h, the yield and current efficiency of benzoquinone could reach 68% and …

Experimental Design Methodology Applied To The Oxidation Of Quinolines In Aqueous Medium By Electro-Fenton Process, Souhaila Trabelsi Souissi, Nihal Oturan, Nizar Bellakhal, Mehmet A. Oturan

Journal of Electrochemistry

The degradation behavior of 8-hydroxyquinoleine sulfate (8-HQS), a model molecule of quinolines, was studied in an aqueous medium by electro-Fenton process using a carbon felt cathode and a platinum anode. The great oxidation ability of this process is due to a large production of hydroxyl radical (OH) by electrochemically induced Fenton’s reagent (H₂O₂, Fe²⁺). Hydroxyl radicals are very powerful oxidizing agents which react on organics up to complete mineralization. A factorial experimental design was used for determining the operating parameters on the degradation of 8-HQS in an aqueous medium. The results showed that the …

Optimization Of Polymer Separation By Gradient Polymer Elution Chromatography, Gideon R. Liem, Linda Nien-Hwa Wang

The Summer Undergraduate Research Fellowship (SURF) Symposium

High Performance Liquid Chromatography (HPLC) has been a versatile separation method for polymers for many years. Analysis of different polymers by HPLC is typically done by utilizing the differential solubility of the polymers by mixing a good solvent and an anti-solvent in various compositions. This method is called Gradient Polymer Elution Chromatography (GPEC). While GPEC has been used extensively, it commonly uses a linear gradient to separate components. Linear solvent gradients consume a lot of solvent and take a relatively long time (> 30 minutes) to complete. The goal of this study is to develop a step gradient from a …

An Analysis Of The Impact Of Storage Temperature, Moisture Content & Duration Upon The Chemical Components & Bioprocessing Of Lignocellulosic Biomass, Arun Athmanathan

Open Access Dissertations

The successful utilization of lignocellulosic biomass as a feedstock for fuels and chemicals necessitates storage for 2-6 months. It is correspondingly important to understand the impact of storage parameters - moisture concentration, temperature and duration - on biomass quality.

As aerobic storage is the most viable large-scale solution, aerobic storage experiments were carried out with three projected bioenergy feedstocks - sweet sorghum (Sorghum bicolor) bagasse, corn (Zea mays) stover and switchgrass (Panicum virgatum). Stored samples of each were examined for dry matter loss and composition change to develop a material balance around carbohydrates and lignin.

A mean dry matter loss …

Preparation Of Mesoporous Silica Supported Ruthenium Oxides And The Application And Kinetic Study In The Catalysis Of Water Oxidation, Yang Zhang

Open Access Dissertations

Photo-induced water splitting of water into H2 and O2 has been a major focus in the development of clean and renewable energy. The development of viable and efficient catalysts that facilitates O2 production remains the major challenge in the study of the corresponding half-reaction of water oxidation. There are plenty of metal oxides reported active in the catalysis of water oxidation. However, several important performance bench marks of those materials, such as the non-stoichiometric production of O2, slow reaction rate and/or low quantum efficiency, remain to be improved.

Ruthenium oxide (RuO2) has long been known as one of the most …

Design And Assembly Of Nanostructured Complex Metal Oxide Materials For The Construction Of Batteries And Thermoelectric Devices, Gautam Ganapati Yadav

Open Access Dissertations

Thermoelectric devices and lithium-ion batteries are among the fastest growing energy technologies. Thermoelectric devices generate energy from waste heat, whereas lithium-ion batteries store energy for use in commercial applications. Two different topics are bound with a common thread in this thesis - nanotechnology! In fact, nanostructuring is a more preferred term for the approach I have taken herein. Another commonality between these two topics is the material system I have used to prove my hypotheses - complex metal oxides.

Complex metal oxides can be used for both energy generation and storage as they are stable at high temperatures, are benign …

Development Of Quantitative Ft- Ir Methods For Analyzing The Cure Kinetics Of Epoxy Resins, Sang Ha Son

Open Access Dissertations

Epoxy thermosets are important engineering materials with applications in coating, adhesives, packaging and as structural components in a variety of advanced engineering products. The ultimate performance of polymer critically depends upon the details of the cure chemistry used to produce the thermoset. In order to better understand and monitor the cure chemistry, quantitative analysis of the FT-IR response has been developed for describing the epoxy-amine curing reaction as well as monitoring the hydrogen bonding that occurs in these systems The FT-IR analysis includes (i) quantitative deconvolution of complex peaks into individual spectral contributions, (ii) peak identification via DFT analysis and …

Elucidation Of Chiral Recognition Mechanisms Of Solutes By Amylose Tris[(S)-Alpha-Methylbenzylcarbamate] Sorbent, Hung-Wei Tsui

Open Access Dissertations

Enantioselective separations of chiral molecules are important in various chemical fields, such as pharmaceuticals and agrochemicals industries. Polysaccharide-based sorbents have been widely used in chiral liquid chromatography. The recognition mechanisms which determine their enantioselectivities are not completely understood.

In this dissertation, the chiral recognition mechanisms of a widely used commercial sorbent, amylose tris[(S)-alpha-methylbenzylcarbamate], for benzoin (B) enantiomers were first studied. The HPLC data for benzoin with pure n-hexane as the mobile phase have been obtained. The behavior of sorbent-solute-hexane systems can be interpreted by considering only sorbent solute two-component interactions. Infrared (IR) spectra showed evidence of substantial hydrogen bonding (H-bonding) …

The Effect Of Composition On The Linear And Nonlinear Mechanical Properties Of Particulate Filled Elastomers, Oluwaseyi Ogebule

Open Access Dissertations

Engineering elastomers are materials capable of undergoing large deformation upon load application and recovering upon load removal. From car tires to building vibration isolator systems, elastomers are the most versatile of engineering materials. The inclusion of particulate fillers into elastomers enhances their mechanical properties (modulus, tensile strength, toughness, tear resistance, etc) thereby extending their applicability to more demanding functions. The automotive, healthcare, construction, adhesives and consumer products are some of the many industries that produce finished goods containing elastomeric parts.

Despite the various concepts on reinforcement in filled elastomers, a complete understanding of their linear viscoelastic properties and the nonlinear …

Energy Systems Analysis For A Solar Economy, Dharik Sanchan Mallapragada

Open Access Dissertations

The use of solar energy for human needs faces challenges owing to its relatively low energy intensity and intermittent availability, coupled with the constrained availability of renewable carbon and land resources. This study uses systems analysis tools to identify carbon and energy efficient transformations of solar energy for different purposes, including transportation fuels and grid-scale energy storage. These efforts have been complemented with a feasibility analysis of existing fossil-energy and other hybrid pathways.

In an era of limited fossil resources, liquid fuels from sustainably available (SA) biomass could meet the energy needs of the transportation sector. We present a method …

Spectroscopic And Kinetic Study Of Copper-Exchanged Zeolites For The Selective Catalytic Reduction Of Nox With Ammonia, Shane Adam Bates

Open Access Dissertations

The recent application of metal-exchanged, small-pore zeolites for use in the selective catalytic reduction (SCR) of NO_x with ammonia NH₃ for automotive deNO_x applications has been a great stride in achieving emission standard goals. Copper-exchanged SSZ-13 (Cu-SSZ-13), the small-pore zeolite in this study, has been shown to be very hydrothermally stable and active under conditions presented in the exhaust of the lean-burn diesel engine. In this work, detailed studies were performed to identify many aspects of the active site(s) in Cu-SSZ-13 in order to learn about the standard SCR mechanism.

A series of seven Cu-SSZ-13 samples were …

Electrosynthesis Of Glycerol Carbonate From Co2 And Glycerol, Huan Wang, Mei-Xia Zhu, La-Xia Wu, Xiao-Ming Xu, Xue-Ru Zhao, Jia-Xing Lu

Journal of Electrochemistry

Glycerol carbonate was obtained from glycerol and carbon dioxide under room temperature and normal pressure by electrochemical method. The effects of synthesis conditions, such as cathode, charge, current density and temperature, on the reaction of glycerol and carbon dioxide have been investigated. The yields of 73% were produced by electrosynthesis of carbonate under the optimized condition, which is much higher than that by common catalysis method. The electrochemical behavior of the reaction system has been studied by cyclic voltammetry, through which the reaction process has been proposed.

Influence Of Pretreatment On Electrocatalytic Property For Methanol Oxidation Of Ptru/Wc, Xiao-Ling Lang, Mei-Qin Shi, Ye-Kun Jiang, Chun-An Ma

Journal of Electrochemistry

The surface of tungsten carbide (WC) was treated by potassium hydroxide (KOH) at different pH values for different time. The PtRu/WC composite was prepared by microwave-assisted polyol method. The phase structure of PtRu/WC composites were characterized by XRD. The electrocatalytic activity was tested by cyclic voltammetry and chronoamperometry. The results indicated that with different pH treatments WC became more readily supported on PtRu. When treating WC in KOH at pH = 14, PtRu exhibited the best degree of crystallinity on WC surface, leading to the highest electrocatalytic activity of PtRu/WC. Moreover, the optimized activity of PtRu/WC towards methanol oxidation was …

Synthesis And Electrochemical Properties Of Li(Ni0.5Co0.2Mn0.3)1-2xTiXNbXO2, Yong Tang, Qin-Lin Liao, Xiang-An Guo

Journal of Electrochemistry

The cathode-active materials of layered Li(Ni_0.5Co_0.2Mn_0.3)_1-2xTi_xNb_xO₂（x=0, 0.002, 0.005, 0.01, 0.02）composites were synthesized by the thermal treatment of the coprecipitated precursor at 900 ^oC in air. The effects of Ti-Nb co-dopants on the structural and electrochemical properties of Li(Ni_0.5Co_0.2Mn_0.3)O₂ were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical experiments. The results show that the small amounts of Ti-Nb co-dopants in Li(Ni_0.5Co_0.2Mn_0.3)O₂significantly decreased the degree of cation mixing in …

Research Progress Of Intermediate Layers In Ti-Based Oxide Anodes, Xiu-Li Song, Hui-Min Yang, Zhen-Hai Liang

Journal of Electrochemistry

Titanium (Ti)-based oxide anodes are excellent anode materials which have been applied widely in electrochemical fields all over the world. Adding intermediate layers in Ti-based oxide anodes can improve the conductivity, lengthen the lifetime and strengthen the stability between Ti base and metal oxides active layers of electrodes. This article reviews the research progress of intermediate layers in Ti-based oxide anodes. At the same time, current problems existed in the field of Ti-based oxide anodes are pointed out and future development trend in oxide electrode with intermediate layers is prospected.

Advanced Treatment Of Dyeing Wastewater For Reuse By Electrochemical Oxidation, Fei-Xiang Chen, Chu-Yin Yang, Ming-Ming Zhou, Jia-De Wang

Journal of Electrochemistry

In response to the characteristics of dye wastewater, the electrochemical oxidation of effluents from the biochemical process of dyeing wastewater was studied in the electrochemical reactor using PbO₂/Ti electrode as the anode and stainless steel plate as the cathode. The results revealed that the electrochemical oxidation could simultaneously remove the Chemical Oxygen Demand (COD), ammonia and chromaticity. At the residence time of 60 min and current density of 10 mA·cm^-2, the COD, ammonia, chromaticity, concentration of chloride ion and pH values could meet the water standards for “the reuse of urban recycling water-water quality standard for …

Voltage Reversal Behavior In Microbial-Anode Fuel Cells, En-Ren Zhang, Jun-Le Niu, Lei Liu, Guo-Wang Diao

Journal of Electrochemistry

Voltage reversal behavior was investigated in microbial-anode fuel cells (MFCs). Electricity-producing biofilms were developed on the surface of anodes in MFCs inoculated with mixed inoculum from activated sludge. MFC duplicates generally exhibited different performances with respect to the internal resistance, the voltage output and the discharging duration when operating in batch mode. Voltage reversal was observed to occur first in the MFC with lower performance when connecting MFCs in series. Analysis of electrode potentials indicated that the potentials of microbial anodes quickly shifted to more positive values when enhancing discharge current, resulting in voltage reversal in MFCs. Increasing temperature would …

Using Hydrolyzed Sludge Liquor As The Substrate Of Microbial Fuel Cell, Peng Liang, Chao Guo, Xia Huang

Journal of Electrochemistry

Hydrolyzed sludge liquor was used as the substrate of microbial fuel cell. When the thermal treatment time increased from 2 h to 96 h, pH varied little between 7.4 and 8.0. When the treatment time increased, the conductivity, COD and alkaline condition increased to 2.53 mS·cm^-1, 2520 mg·L^-1 and 800 mg·L^-1, respectively. Meanwhile, the power density increased to 25 W·m^-3. The COD removal increased firstly, then decreased, and finally reached the maximum of 47% at the hydrolyzed time of 6 h. The maximal coulombic efficiency was 71% when the treatment time was 4 …

Electrocatalytic Oxidation Degradation Kinetics Of Oxalic Acid In A Cylindrical Electrochemical Reactor With Ti/Iro2-Ta2O5 Anode, Jing Su, Hai-Bo Lin, Hong Xu, Wei-Min Huang, Ya-Peng He

Journal of Electrochemistry

The electrocatalytic oxidation degradation kinetics of oxalic acid in a cylindrical electrochemical reactor with Ti/IrO₂-Ta₂O₅  as an anode was studied. The relation between instantaneous current efficiency and organic concentration in bulk was established based on the two paths for direct electrochemical oxidations, and the theoretical model was verified by experiments. The experimental resultswere reasonably consistent with the established kinetic model. Furthermore, the competition between the two paths was explored with the modelparameter analysis.

Performance Of The Electro-Oxidation And Electro-Fenton Processes With A Bdd Anode For The Treatment Of Low Contents Of Pharmaceuticals In A Real Water Matrix, Sirs Ignasi, Antonio Garrido Jos, Brillas Enric

Journal of Electrochemistry

Here, we report the performance of electro-oxidation and electro-Fenton with a boron-doped diamond (BDD) anode for the treatment of single and multicomponent solutions containing small amounts of pharmaceutical residues (i.e., 1 mg·L^-1 paracetamol and/or 1 mg·L^-1 salicylic acid) spiked into a real water matrix at pH 3.0. Electro-oxidation was performed in a BDD/Pt cell, whereas electro-Fenton was carried out in a BDD/air-diffusion cell to electrogenerate H₂O₂ at the cathode, always operating at constant current density. It was found that the decay of both pharmaceuticals by electro-oxidation was more rapid in the real water matrix than …

Characterization Of Samples For Optimization Of Infrared Stray Light Coatings, Carey L. Baxter, Rebecca Salvemini, Zaheer A. Ali, Patrick Waddell, Greg Perryman, Bob Thompson

STAR Program Research Presentations

NASA’s Stratospheric Observatory for Infrared Astronomy (SOFIA) is a converted 747SP that houses a 2.5 m telescope that observes the sky through an opening in the side of the aircraft. Because it flies at altitudes up to 45,000 feet, SOFIA gets 99.99% transmission in the infrared. Multiple science instruments mount one at a time on the telescope to interpret infrared and visible light from target sources. Ball Infrared Black (BIRB) currently coats everything that the optics sees inside the telescope assembly (TA) cavity in order to eliminate noise from the glow of background sky, aircraft exhaust, and other sources. A …

Decoupling The Stationary Navier-Stokes-Darcy System With The Beavers-Joseph-Saffman Interface Condition, Yong Cao, Yuchuan Chu, Xiaoming He, Mingzhen Wei

Mathematics and Statistics Faculty Research & Creative Works

This paper proposes a domain decomposition method for the coupled stationary Navier-Stokes and Darcy equations with the Beavers-Joseph-Saffman interface condition in order to improve the efficiency of the finite element method. The physical interface conditions are directly utilized to construct the boundary conditions on the interface and then decouple the Navier-Stokes and Darcy equations. Newton iteration will be used to deal with the nonlinear systems. Numerical results are presented to illustrate the features of the proposed method.

Preparation And Characterization Of A Novel Composite Electrolyte Ceria-Sulfate For Intermediate Temperature Solid Oxide Fuel Cells, Ze Tong, Yi-Mei Yin, Jie-Wei Yin, Zi-Feng Ma

Journal of Electrochemistry

A novel composite electrolyte SDC-(Li/Na)₂SO₄ was prepared for intermediate temperature solid oxide fuel cells (ITSOFC). The phase structure and cross-sectional morphology were examined by XRD and SEM, respectively, and the ionic conductivity was investigated by AC impedance in a temperature range of 400 ^oC ~ 700 ^oC in air. It was found that the composite electrolyte was composed of two phases: crystal SDC and amorphous (Li/Na)₂SO₄. The conductivity of the composite electrolyte was significantly larger than that of SDC at intermediate temperatures (550 ^oC ~ 700 ^oC) and increased …

Influence Of Electrode Hydrophobicity On Performance Of Alkaline Polymer Electrolyte Fuel Cells, Li-Sheng Tan, Jing Pan, Yao Li, Lin Zhuang, Jun-Tao Lu

Journal of Electrochemistry

In the present work, we study the influence of the electrode hydrophobicity on the performance of alkaline polymer electrolyte fuel cells (APEFCs). QAPS or xQAPS is employed as the membrane and the ionomer, while PTFE is used as a hydrophobic additive in order to adjust the electrode hydrophobicity. We find that enhancing the hydrophobicity of anode can promote the performance of APEFCs, while a moderate hydrophobicity of cathode is required to achieve optimal performance. By using xQAPS as the electrolyte and adding some PTFE in the anode, a peak power density of 132 mW·cm^-2 can be obtained at a …

Electrocatalytic Mechanism And Porous Electrode Mass Transfer Process In Membrane Electrode Assembly For Direct Methanol Fuel Cells, Xin-Dong Wang, Yi-Tuo Wang, Gui-Cheng Liu, Meng Wang, Zhe Tian

Journal of Electrochemistry

Direct methanol fuel cell (DMFC) is considered to be a promising commercial energy conversion device for portable electronics due to its many advantages. In order to improve the performance of DMFC, many companies and research institutes have been launching the deep research and obtaining a lot of conspicuous achievements. In this paper, the electrocatalytic mechanism and porous electrode mass transfer process in membrane electrode assembly (MEA) are analyzed. In addition, combined with the preparation process of MEA, multilayer ordered structures and internal transfer process of the cell, recent progresses of MEA in DMFC are discussed.

Fabrication And Performance Of Lani0.6Fe0.4O3-δCathode Modified By Coating With Gd0.2Ce0.8O2 For Intermediate Temperature Solid Oxide Fuel Cell, Rui-Xuan Ren, Bo Huang, Xin-Jian Zhu, Yi-Xing Hu, Xiao-Yi Ding, Zong-Yao Liu, Ye-Bin Liu

Journal of Electrochemistry

The symmetric cell of LaNi_0.6Fe_0.4O_3-δ/Sc_0.1Zr_0.9O_1.95/LaNi_0.6Fe_0.4O _3-δ was fabricated with screen printing method. A LaNi_0.6Fe_0.4O_3-δ (LNF) cathode was modified by coating with nano-sized gadolinium-doped ceria (GDC, Gd_0.2Ce_0.8O₂) prepared using a simple combustion process within the pores of the cathode. According to the electrochemical impedance spectra (EIS), the polarization resistance of the pure LNF was 0.70 W·cm² at 750 ºC, while 0.13 W·cm² for the 21.3% GDC (by mass)-coated LNF cathode at the …

Multifunctional Corrosion Inhibition Behavior Of Zn-Al Calcined Layered Double Hydroxides For Steel Rebar In Nacl Solution, Xiao-Juan Zhang, Jing-Jing Wang, Shi-Gang Dong, Chang-Jian Lin

Journal of Electrochemistry

The Zn-Al layered double hydroxides (Zn-Al LDHs) and calcined products (Zn-Al CLDHs) were synthesized successfully under a routine air atmosphere. The results showed that both Zn-Al LDHs and Zn-Al CLDHs had obvious flake structures. The corrosion inhibition of Zn-Al CLDHs for steel rebar in NaCl solution was studied by electrochemical techniques. It was found that the corrosion rate of steel rebar decreased significantly after the steel rebar was treated by Zn-Al CLDHs in NaCl solution for 3 h. It was indicated that Zn-Al CLDHs could absorb Cl^- and release OH^- during their reconstruction process, which provided dual protection …

Ramjet Combustion Chamber, Paul Cameron Stone

Aerospace Engineering

A ramjet combustion chamber is designed and some initial assembly fabrication and test completed as a component of a ramjet graduate project for California Polytechnic State University, San Luis Obispo Supersonic Wind Tunnel. The combustor design is driven by a theoretical model created by a Cal Poly graduate student, Harrison Sykes. Temperature, pressure, and fuel flow will be measured.