Chemical Engineering Commons^™

Corrosion Rate Of Carbon Steel For Flowline And Pipeline As Transmission Pipe In Natural Gas Production With Co2 Content, Andi Rustandi, Muhammad Adyutatama, Enriko Fadly, Norman Subekti

Makara Journal of Technology

The purpose of this research is to investigate the corrosion rate of carbon steel as flowline and pipeline in natural gas production with CO2 content. The influence of variety of conditions that represent the actual conditions in practice such as CO2 partial pressure and solution composition, particularly NaCl percentage were performed. Research conducted by polarization test and simulation methods using PREDICTTM software. The result of this research is used to illustrate the level of corrosion rate of typical carbon steel i.e. API 5L X-52 occurred in natural gas pipelines due to the effect of dissolved CO2. From the experiments obtained …

Modification Of Flow Structure Over A Van Model By Suction Flow Control To Reduce Aerodynamics Drag, Harinaldi Harinaldi, Budiarso Budiarso, Warjito Warjito, Engkos Achmad Kosasih, Rustan Tarakka, Sabar Pangihutan Simanungkalit, I Gusti Made Fredy Lay Teryanto

Makara Journal of Technology

Automobile aerodynamic studies are typically undertaken to improve safety and increase fuel efficiency as well as to find new innovation in automobile technology to deal with the problem of energy crisis and global warming. Some car companies have the objective to develop control solutions that enable to reduce the aerodynamic drag of vehicle and significant modification progress is still possible by reducing the mass, rolling friction or aerodynamic drag. Some flow control method provides the possibility to modify the flow separation to reduce the development of the swirling structures around the vehicle. In this study, a family van is modeled …

Age, Gender, And Muscle Strength: A Study Based On Indonesian Samples, Henny Henny, Hardianto Iridiastadi, Iftikar Zahedi Sutalaksana

Makara Journal of Technology

Age and gender have been commonly used as a main criterion in accepting a job aplicant, but it is usually not clear how these affect job performance. While a number of recent studies have been done that describe the relationships between age, gender, and participants capacity (e.g., muscle strength), the results have been inconclusive. In Indonesia, in particular, such issues have been rarely investigated, and it is still important to study the issue since the relationships between these factors are population-specific. This study aimed at describing the relationships between age and muscle strength among workers for both genders. Ninety-six male …

Circularly Polarized Microstrip Array Antenna For Ground Segment In Quasi-Zenith Satellite System, Fitri Yuli Zulkifli, Eko Tjipto Rahardjo

Makara Journal of Technology

In satellite communication system, antenna plays an important role. Therefore, the antenna must meet some requirements, such as high gain, circular polarization, and good directivity. In this paper, a four element linear array triangular patch microstrip antenna with cross slot is designed to be used for Quasi-Zenith satellite system. A simulation study as well as experimental study was carried out. The simulation showed that the 3 dB axial ratio bandwidth of 87 MHz (2.569-2.656 GHz) is achieved while the measured results showed 96 MHz (2.556-2.652 GHz). The linear array of 4 element antenna has a gain of 13.73 dB and …

Concurrent Engineering Of Tolerance Synthesis And Process Selection For Products With Multiple Quality Characteristcs Considering Process Capability, Mohamad Imron Mustajib

Makara Journal of Technology

The existences of variances that are very difficult to be removed from manufacturing processes provide significance of tolerance to the product quality characteristics target of customer functional requirement. Furthermore, quality loss incurred due to deviation of quality characteristics of the target with a specified tolerance. This article discusses the development of concurrent engineering optimization model of tolerance design and manufacturing process selection on product with multiple quality characteristics by minimizing total costs in the system, namely total manufacturing cost and quality loss cost as functions of tolerance, also rework and scrap costs. The considered multiple quality characteristics have interrelated tolerance …

Pineapple Liquid Waste As Nata De Pina Raw Material, Agus Sutanto

Makara Journal of Technology

This research aims to study the quantity, quality, ecological and economic feasibility of nata de pina production (NP) from pineapple liquid waste (PLW). The design of the study employs complete random design (CRD) with three treatments: PLW without nutrients addition (A), PLW nutrients addition (B), and PLW stored for six months with nutrients addition (C). The nata de pina’s production factors measured were weight, thickness, fiber content, color, brightness, and residual waste. The highest weight was reached in treatment B (899 grams), followed by treatment A (616.4 grams), and C (477.8 grams). The thickness of NP of the height and …

Modeling Of A New Structure Of Precision Air Conditioning System Using Secondary Condenser For Rh Regulation, Aries Subiantoro, Nasruddin Nasruddin, Feri Yusivar, Muhammad Idrus Al-Hamid, Bagio Budiardjo

Makara Journal of Technology

A dynamic mathematical model for a new structure of precision air conditioning (PAC) has been developed. The proposed PAC uses an additional secondary condenser for relative humidity regulation compared to a basic refrigeration system. The work mechanism for this system and a vapour-compression cycle process of the system are illustrated using psychrometric chart and pressure-enthalpy diagram. A non-linear system model is derived based on the conservation of mass and energy balance principles and then linearized at steady state operating point for developing a 8th-order state space model suited for multivariable controller design. The quality of linearized model is analyzed in …

Optimizing Fermentation Medium To Produce Cyclosporin A Using Response Surface Methodology, Rofiq Sunaryanto

Makara Journal of Technology

Response surface methodology (RSM) is a three factorial model which illustrates the relationship between one or more independent variables. RSM can be used to optimize the fermentation medium for the production of Cyclosporin A from the isolate Tolypocladium inflatum. The optimal point of the response surface area is predicted by using a seconddegree polynomial model and applying the statistic model obtained from the central composite design (CCD). The results of optimizing the fermentation medium for Cyclopsorin using the three independent variables of glucose, casein, and KH2PO4 show that all three of the independent variables affect the production of Cyclosporin A. …

Analysis Of The Penney-Ante Game Using Difference Equations: Development Of An Optimal And A Mixed-Strategies Protocol, Carl Barratt, Pauline Schwartz

Chemistry and Chemical Engineering Faculty Publications

Penney-Ante is a well known two-player (Player I and Player II) game based on an information paradox. We present a new approach, using difference-equations, to analyzing the outcome for each player. One strategy yields a winning outcome of 75% for Player II, the player playing second. The approach also permits investigation of non-optimal strategies, and demonstrates how mixing of such strategies can be used to tune the winning edge of either player. We generalize the analysis to accommodate the possibility of a biased coin.

Controlling Nanoparticles Formation In Molten Metallic Bilayers By Pulsed-Laser Interference Heating, Mikhail Khenner, Sagar Yadavali, Ramki Kalyanaraman

Mathematics Faculty Publications

The impacts of the two-beam interference heating on the number of core-shell and embedded nanoparticles and on nanostructure coarsening are studied numerically based on the non-linear dynamical model for dewetting of the pulsed-laser irradiated, thin (< 20 nm) metallic bilayers. The model incorporates thermocapillary forces and disjoining pressures, and assumes dewetting from the optically transparent substrate atop of the reflective support layer, which results in the complicated dependence of light reflectivity and absorption on the thicknesses of the layers. Stabilizing thermocapillary effect is due to the local thickness-dependent, steady- state temperature profile in the liquid, which is derived based on the mean substrate temperature estimated from the elaborate thermal model of transient heating and melting/freezing. Linear stability analysis of the model equations set for Ag/Co bilayer predicts the dewetting length scales in the qualitative agreement with experiment.

Kinetic Models Of The Prebiotic Replication Of Dsrna Under Thermal Cycling Conditions, Pauline Schwartz, Dante M. Lepore, Carl Barratt

Chemistry and Chemical Engineering Faculty Publications

We present computational models for the replication of double stranded RNA (dsRNA) or related macromolecules under thermal cycling conditions that would reflect prebiotic (i.e. non-enzymatic) environments. Two models of the replication of dsRNA are represented as multi-step chemical systems. The objective of this investigation was to better understand the kinetic features of such chemical systems. It is shown that thermal cycling in a chemical system is advantageous (relative to a fixed temperature) if there are two competing reactions, one favored at high temperature and one favored at low temperature. For the prebiotic replication of dsRNA, a high temperature favors formation …

A Review Of Some Subtleties Of Practical Relevance, Keqin Gu

SIUE Faculty Research, Scholarship, and Creative Activity

This paper reviews some subtleties in time-delay systems of neutral type that are believed to be of particular relevance in practice. Both traditional formulation and the coupled differential-difference equation formulation are used. The discontinuity of the spectrum as a function of delays is discussed. Conditions to guarantee stability under small parameter variations are given. A number of subjects that have been discussed in the literature, often using different methods, are reviewed to illustrate some fundamental concepts. These include systems with small delays, the sensitivity of Smith predictor to small delay mismatch, and the discrete implementation of distributed-delay feedback control. The …

Heat Transfer Enhancement In A Straight Channel Via A Rotationally Oscillating Adiabatic Cylinder, Ali Beskok, Mehrdad Raisee, Bayram Celik, Bedri Yagiz, Mohsen Cheraghi

Mechanical & Aerospace Engineering Faculty Publications

Heat convection from the uniformly heated walls of a straight channel in presence of a rotationally oscillating cylinder (ROC) is simulated at Re = 100. Heat transfer enhancement due to vortex shedding from the ROC is investigated. Systematic studies are performed to explore the rotation angle and frequency influences on heat transfer by varying the latter in range of the lock-in regime and the former from 0 to 2 π/3. All simulation results are based on the numerical solutions of two-dimensional, unsteady, incompressible Navier-Stokes and energy equations using an h/p type finite element algorithm. Considering time periodicity of the resulting …

Investigation Of Carbon Corrosion Resistance Of Cnt Containing Electrode, Diana Larrabee, William A. Rigdon, Eli Mcpherson, Joshua Sightler, Xinyu Huang

Faculty Publications

Carbon support corrosion is one of the major degradation mechanisms of polymer electrolyte membrane (PEM) fuel cell. Carbon oxidation occurs in PEM electrode and is accelerated at high potential created by adverse operating conditions and improper distribution of reactants and products [1, 2, 3]. Carbon corrosion can lead to the thinning of the electrode layer and severe performance degradation. The detailed mechanisms of carbon support corrosion induced performance loss are still not fully understood; it is believed that the following events contribute to the decay: (1) structural collapse of the porous electrode due to the loss of carbon; (2) carbon …

Oxidation Of Borides And Carbides With Y2o3 And Ta Additions, Salvador Manuel Rodriguez

Open Access Theses & Dissertations

The study presented here describes an investigation of an oxidation scale of a fully-sintered Y2O3-ZrB2-TiC composite exposed in air at 1173K. Upon oxidation of the boride/carbide, a ZrO2-TiO2 was expected to form similar to the ZrO2-SiO2 dual scale of an oxidized ZrB2-SiC. The 47wt% Y2O3-38wt%ZrB2-16wt%TiC composite formed a dual scale consisting primarily of an Y2O3-ZrO2-TiC inner scale with an outer scale of ZrO2-TiO2-Y2O3.

The samples oxidized with a parabolic layer growth allowing the calculation of the effective diffusion coefficient indicating that the oxidation was controlled by oxygen ingress through primarily the ZrO2-Y2O3 phase. The oxygen potential between the inner layer …

Formation Of Organized Nanostructures From Unstable Bilayers Of Thin Metallic Liquids, Mikhail Khenner, Sagar Yadavali, Ramki Kalyanaraman

Mathematics Faculty Publications

Dewetting of pulsed-laser irradiated, thin (< 20 nm), optically reflective metallic bilayers on an optically transparent substrate with a reflective support layer is studied within the lubrication equations model. A steady-state bilayer film thickness (h) dependent temperature profile is derived based on the mean substrate temperature estimated from the elaborate thermal model of transient heating and melting/freezing. Large thermocapillary forces are observed along the plane of the liquid-liquid and liquid-gas interfaces due to this h-dependent temperature, which, in turn, is strongly influenced by the h-dependent laser light reflection and absorption. Consequently the dewetting is a result of the competition between thermocapillary and intermolecular forces. A linear analysis of the dewetting length scales established that the non-isothermal calculations better predict the experimental results as compared to the isothermal case within the bounding Hamaker coefficients. Subsequently, a computational non-linear dynamics study of the dewetting pathway was performed for Ag/Co and Co/Ag bilayer systems to predict the morphology evolution. We found that the systems evolve towards formation of different morphologies, including core-shell, embedded, or stacked nanostructure morphologies.

Analysis Of Biomass/Coal Co-Gasification For Integrated Gasification Combined Cycle (Igcc) Systems With Carbon Capture, Henry A. Long Iii

LSU New Orleans Theses and Dissertations

In recent years, Integrated Gasification Combined Cycle Technology (IGCC) has become more common in clean coal power operations with carbon capture and sequestration (CCS). Great efforts have been spent on investigating ways to improve the efficiency, reduce costs, and further reduce greenhouse gas emissions. This study focuses on investigating two approaches to achieve these goals. First, replace the subcritical Rankine steam cycle with a supercritical steam cycle. Second, add different amounts of biomass as feedstock to reduce emissions. Finally, implement several types of CCS, including sweet- and sour-shift pre-combustion and post-combustion.

Using the software, Thermoflow®, this study shows that utilizing …

Effect Of Copper Addition On Mechanical Properties And Electrical Conductivity Of Pp/C-Cu Bipolar Plate Composites, Anne Zulfia, Taufik Abimanyu, Verina Warga Dalam

Makara Journal of Technology

Effect of Copper Addition on Mechanical Properties and Electrical Conductivity of PP/C-Cu Bipolar Plate Composites. Bipolar plate is a major component in PEM fuel cell which possess main function of collecting and removing electrons from anode to cathode. Therefore, materials for bipolar plates produced must have high electrical conductivity. To obtain bipolar plate materials which is cheap, lightweight and high conductivity, so it is developed bipolar plates material based on PP/C-Cu composite. PP/C-Cu composites has been made by mixing all materials then compounding, rheomix, hot blending and hot press. Cu (Copper) has been used various from 0.1 wt%, 1 wt% …

Application Of Empirical Orthogonal Function Models To Analyze Shoreline Change At Bangkalan Madura, Darius Arkwright, Suntoyo Suntoyo

Makara Journal of Technology

Bangkalan’s shoreline, especially on the opposite side of Surabaya, has been evaluated to determine the morphological changes due to wave attack, near-shore current, long-shore sediment transport and coastal configuration. This research aims to determine the dominant patterns of variation of Bangkalan’s shoreline change, expressed by Eigen-function in empirical orthogonal function (EOF) models. That was started with data collection such as oceanographic data (wave and tidal), bathymetry and topographic map and sediment data. All data was used for forecasting two-monthly shoreline. Coordinate of two-monthly shoreline was used as input of EOF model. The first Eigen mode is a profile of shoreline …

The Effectiveness Of Anaerobic Baffled Reactor And Rotating Biological Contactor In Batik Wastewater Treatment, Augustinus Ignatius Kristijanto, Widhi Handayani, Purwanti Asih Anna Levi

Makara Journal of Technology

Batik is one of popular arts of Indonesia. The batik industries in Sragen, Central Java, are prepared to compete in global market. In order to realize that objective, batik products should fulfill some qualifications, one of which is “environmental friendliness”. As batik production is usually generating wastewater which pollutes the environment, the technology of wastewater treatment should be developed to solve the problem. This preliminary study has been done to assess the effectiveness of anaerobic baffled reactor (ABR) and rotating biological contactor (RBC) in batik wastewater treatment. In 40 days of treatment period, the ABR performance in reducing pollutants showed …

Physical Characterization And Desulfurization Of Biobriquette Using Calcium-Based Adsorbent, Mahidin Mahidin, Asri Gani, Khairil Khairil

Makara Journal of Technology

Combustion of coal and co-combustion of their co-fuel contribute to gas emissions. Among the gas emissions are SOx, NOx, CO and CO2. Introduction of calcium based adsorbent is addressed to absorb SO2 that release to the atmosphere during the combustion process. Objective of the research is at first to observe the physical characteristics of biobriquettes as a function of briquette compositions (coal to palm kernel shell ratios) and Ca/S ratios (Ca in adsorbent and S in briquette) using a natural adsorbent (shellfish waste). The second objective is to investigate desulfurization characteristics as a function of Ca/S ratios and desulfurization temperatures …

Medium Density Fibreboard Made Of Acetylated Sludge From Paper Mill, Luthfi Hakim, Evalina Herawati, I Nyoman Jaya Wistara

Makara Journal of Technology

Medium Density Fibreboard Made of Acetylated Sludge from Paper Mill. Research of using sludge as raw material for making medium density fibreboard (MDF) was useful to create additional value of sludge. The objective of the research was to evaluate physical properties, mechanical properties, and durability of MDF from acetylated sludge in 4 levels of acetate anhydride (0%, 3%, 5%, and 7%) with 3 replicates. The MDF was made using dry process. After materials were mixed with adhesives, they were pressed using hotpress under 170 oC temperature and 45 Pa pressure for 25 minutes. The size of the MDF sample was …

Cassava Pulp As A Biofuel Feedstock Of An Enzymatic Hydrolysis Proces, Djuma’Ali Djuma’Ali, Nonot Soewarno, Sumarno Sumarno, Dyah Primarini, Wahono Sumaryono

Makara Journal of Technology

Cassava pulp, a low cost solid byproduct of cassava starch industry, has been proposed as a high potential ethanolic fermentation substrate due to its high residual starch level, low ash content and small particle size of the lignocellulosic fibers. As the economic feasibility depends on complete degradation of the polysaccharides to fermentable glucose, the comparative hydrolytic potential of cassava pulp by six commercial enzymes were studied. Raw cassava pulp (12% w/v, particle sizeμm) hydrolyzed by both commercial pectinolytic (1) and amylolytic (2) enzymes cocktail, yielded 70.06% DE. Hydrothermal treatment of cassava pulp enhanced its susceptibility to enzymatic cleavageas compared to …

Alos/Palsar Image Processing Using Dinsar And Log Ratio For Flood Early Detection In Jakarta Based On Land Subsidences, Dodi Sudiana, Mia Rizkinia

Makara Journal of Technology

Flood that occurred in Jakarta is not only influenced by rainfall, urban planning system and drainage alone, but also may be involved land subsidence (LS). LS is possible in because Jakarta stands on top of layers of sediments and the presence of ground water consumption in very large quantities. In this research, the Advanced Land Observing Satellite (ALOS)/Phased Array type L-band Synthetic Aperture Radar (PALSAR) data was processed to determine the level of LS in Jakarta area and its relation to flood potential area. Differential interferometry method (DInSAR) was performed on two PALSAR data with different acquisition years, i.e. 2007 …

Analytical And Computational Simulation Approaches To Design Low Energy Glass Block, Floriberta Binarti, Agustinus Djoko Istiadji, Prasasto Satwiko, Priyo Tri Iswanto

Makara Journal of Technology

Analytical and Computational Simulation Approaches to Design Low Energy Glass Block. An environmentally friendly process was developed to produce a low embodied energy glass block from waste glasses. The energy efficiency of the glass block is represented by its thermal conductance (U)

Improvement Of High Temperature Oxidation Of Low Carbon Steel Exposed To Ethanol Combustion Product At 700 °C By Hot-Dip Aluminizing Coating, Mohammad Badaruddin

Makara Journal of Technology

Low carbon steel (AISI 1005) was coated by hot-dipping into a molten Al-10% Si bath at 700 °C for 18s. After hotdipping treatment, the coating layers consisted of Al, Si, FeAl3, τ5-Fe2Al8Si, and Fe2Al5. The bare steel and the aluminized steel were isothermally oxidized at 700 °C in ethanol combustion product at atmospheric pressure for 49 h. The aluminized steel shows good performance in high temperature oxidation because the formation of Al2O3 layer on the coating surface. The growth of iron oxide nodules on the surface coating was accelerated by rapid outward diffusion of Fe-ions due to the presence of …

Establishment Code Hand Palm (Palm Code) 2d Gabor-Based Method, I Ketut Gede Darma Putra, Wira Bhuana, Erdiawan Erdiawan

Makara Journal of Technology

Establishment Code Hand Palm (Palm Code) 2D Gabor-Based Method. Palmprint is relatively new in physiological biometrics. Palmprint ROI segmentation and feature extraction are two important issues in palm print recognition. This paper introduces two steps in the center of mass moment method for ROI segmentation that will be applied in the Gabor 2D filter to obtain palm code as palmprint feature vector. Normalized Hamming distance was used to measure the similarity degrees of two feature vectors of palmprint. The system was tested using database 1000 palmprint images generated from 5 samples from each of the 200 persons randomly selected with …

Flutter Analysis Of Rx-420 Balistic Rocket Fin Involving Rigid Body Modes Of Rocket Structures, Novi Andria

Makara Journal of Technology

Flutter Analysis of RX-420 Balistic Rocket Fin Involving Rigid Body Modes of Rocket Structures. Flutter is a phenomenon that has brought a catastrophic failure to the flight vehicle structure. In this experiment, flutter was analyzed for its symmetric and antisymmetric configuration to understand the effect of rocket rigid modes to the fin flutter characteristic. This research was also expected to find out the safety level of RX-420 structure design. The analysis was performed using half rocket model. Fin structure used in this research was a fin which has semispan 600 mm, thickness 12 mm, chord root 700 mm, chord tip …

Flexible Connection Elastomeric Rubber As A Pounding Resisting Element Between Two Adjacent Buildings, Yuskar Lase, James Jatmiko Oetomo

Makara Journal of Technology

Flexible Connection Elastomeric Rubber as a Pounding Resisting Element between Two Adjacent Buildings To solve pounding problem of two adjacent buildings, structural designer usually employs a dilatation between the structures or make the two structures as a monolith structure. Other alternative is by using an elastomeric rubber as a pounding resisting element between the two structures. Effectiveness in applying elastomeric rubber component as flexible connection of two adjacent structures is the main focus of this paper. Various simulations such as structure models, earthquake excitations and openings in gap element are studied. Observation of maximum structural responses will be performed for …

Optimation Of Nitrogen And Phosphorus In Azolla Growth As Biofertilizer, Hany Handajani

Makara Journal of Technology

Nitrogen is one of the most important minerals for living organisms. Azolla is known as a small water fern which can fix nitrogen through the symbiotic association with the blue green algae Anabaena. Experimental studies were carried out in the glass house, investigating the growth of Azolla using different levels of nitrogen and phosphorus in the media. The experiment used 12 treatments with 3 levels of nitrogen (0, 5, and 10 mg atom/L) and 4 levels of phosphorus (0, 10, 20, and 30 mg atom/l) in a factorial design with 3 replicates. The results show that the highest biomass for …