Chemical Engineering Commons^™

Stability Analysis Of A More General Class Of Systems With Delay-Dependent Coefficients, Chi Jin, Keqin Gu, Islam Boussaada, Silviu-Iulian Niculescu

SIUE Faculty Research, Scholarship, and Creative Activity

This paper presents a systematic method to analyse the stability of systems with single delay in which the coefficient polynomials of the characteristic equation depend on the delay. Such systems often arise in, for example, life science and engineering systems. A method to analyze such systems was presented by Beretta and Kuang in a 2002 paper, but with some very restrictive assumptions. This work extends their results to the general case with the exception of some degenerate cases. It is found that a much richer behavior is possible when the restrictive assumptions are removed. The interval of interest for the …

Molecularly Conductive Behavior Of Blended Polymer Electrolyte-Based Cmc/Pva, Noor Saadiah Mohd Ali, Dishen Zhang, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

This study investigated the electrical conduction and structural behavior of blended polymer electrolyte (BPE)-based carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA) in the development of solid-state electrochemical devices. Based on impedance spectroscopy and correlating Fourier transform infrared (FTIR) with thermogravimetric analysis, a framework was proposed to explain the structural enhancement of the BPE system. As revealed by FTIR, the optimum conductivity of CMC/PVA BPEs was 9.21 × 10−6 Scm−1 for 80:20 composition attributed to the intermolecular attraction between the polymers. Thermal stability of the CMC/PVA was influenced by the formation of a hydrogen bond between the hydroxyl (-OH), carboxylate (-COO-), …

Multistage Sonication Effect On The Composition And Properties Of Degraded Chitosan Product, Nurul Laili Arifin, Emma Savitri, Anjar Indah, Fesa Putra, Sumarno Sumarno

Makara Journal of Technology

The sonication method randomly breaks polymer chains to produce a varied distribution of products. A scheme with multi-stage sonication steps is proposed to identify oligomers and low molecular weight chitosan based on changes to the degrad-ed product. For each sonication level, 1% (w/v) chitosan in 1% (v/v) aqueous acetic acid was sonicated for 120 min at 60 °C. The products of the sonication treatment were deprotonized by adding an alkali solution, freeze dried and insoluble product re-sonicated until a low molecular weight was produced. Low molecular weight chitosan/insoluble products were character-ized with Fourier-transform infrared spectra (FT-IR) and X-ray diffraction (XRD) …

Study Of Zno Nanospheres Fabricated Via Thermal Evaporation For Solar Cell Application, Fatin Farisha Alia Azmi, Bouchta Sahraoui, Saifful Kamaluddin Muzakir

Makara Journal of Technology

A solar cell is a device that absorbs light energy to generate electrical energy. A typical example of a solar cell is the quantum dot solar cell (QDSC), which consists of three main components: (i) fluorophore: the component that absorbs light and generates excited state electrons and holes, (ii) photoelectrode: the component that transports the excited state electron and prevents recombination of excited state electrons and holes, and (iii) electrolyte: the component that re-plenishes the vacancy left by the excited electron in the hole. Despite the increasing number of research in the QDSC field, to date, a device with significant …

Electrical Properties Of A Novel Solid Biopolymer Electrolyte Based On Algi-Nate Incorporated With Citric Acid, Ahmad Faizrin Ahmad Fuzlin, Noor Syahida Ismail, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

In the present study, a novel solid biopolymer electrolyte (SBE) system is introduced by doping citric acid into alginate polymer. A sample of the alginate-citric acid SBE system was prepared via a solution casting technique. Using electrical impedance spectroscopy (EIS), the electrolytes of alginate-citric acid analyzed from 5 Hz to 1 MHz achieved the highest conductivity at 20 wt.% of 5.49 × 10-7 S cm-1. The temperature dependence of various citric acid amounts obeyed the Arrhenius rule with R2~1, where all SBE systems were thermally activated with increasing temperature. The dielectric studies of the alginate-citric acid SBE system showed non-Debye …

Wavelet Transform On Digital Rainbow Hologram Based On Spectral Compression For Quality Enhancement In 3d Display Media, Ucuk Darusalam, Panca Dewi Pamungkasari

Makara Journal of Technology

A digital rainbow hologram (DRH) is a potential next-generation three-dimensional display media for the development of modern and smart electronics devices. It is one of the methods that can support the characteristic whereby a realistic display media occupies the space that the real object would have occupied. Since a rainbow hologram records a large amount of spatial or temporal frequency component from the object that represents the rainbow spectrum, a large amount of information needs to be decoded digitally. In this paper, to reconstruct a DRH, we propose a novel method based on the modulation of red, green, and blue …

Data Fusion Method Based On Adaptive Kalman Filtering, Bernadus Herdi Sirenden

Makara Journal of Technology

This paper discusses data fusion methods to combine the data from a rotary encoder and ultrasonic sensor. Both sensors are used in a micro-flow calibration system developed by the Research Center of Metrology LIPI. The methods studied are hierarchical data fusion and Kalman filtering. Three types of Kalman filters (KFs) are compared: the conventional Kalman filter and two adaptive Kalman filters. Moreover, a method to combine the uncertainty results from KF in hierarchical data fusion is proposed. The aim of this study is to find appropriate methods of data fusion that can be implemented in micro-flow calibration systems. Data from …

Sorption-Based Energy Storage Systems: A Review, Kyaw Thu, Nasruddin Nasruddin, Sourav Mitra, Bidyut Baran Saha

Makara Journal of Technology

Mismatched timing between the supply and demand of energy calls for reliable storage systems. Energy storage systems have become further significant with the widespread implementation of renewable energy. These systems can mitigate problems that are often associated with renewable energy sources such as supply unreliability while meeting the de-mand during peak hours. Energy can be stored in various forms, yet storage systems can be generally grouped based on their output forms, namely (i) electricity and (ii) heat or thermal energy. Electrical energy is the most convenient and effective form since it can power almost all modern devices. However, the electricity …

Experimental Investigation Of The Manufacture Of Tunable Graphene Oxide Filter Membranes Using Intense Pulse Light, Joshua H Kotter

Electronic Theses and Dissertations

Reduced graphene oxide is a thin, strong, and inexpensive material with a channel and pore structure that make it a promising candidate for a filtration material. Reduced graphene oxide has been produced and tested in the laboratory, but a lack of scalable manufacturing techniques have limited its commercial use.

This thesis has shown that graphene oxide can be rapidly manufactured with an industrially scalable flash reduction process. The flash reduction process uses 0.58 millisecond pulses from a xenon lamp to reduce the graphene oxide film in less than a minute. Results for partially reduced graphene oxide membranes tuned by the …

Design Of A Portable Biogas Purification And Storage System, Anikumar Kosna, Bade Shrestha

Faculty Research and Creative Activities Award (FRACAA)

The objective of this study is to propose and design a commercial portable purification and storage system to commercialize biogas (which mainly consists of 45 - 75 % of methane and 15 - 16% of carbon dioxide), produced from household/non-commercial biogas plants. The selection of purification process is based on the portability of the purification system.

Examination Of Flow Dynamics And Passive Cooling In An Ultra Compact Combustor, Tylor C. Rathsack

Theses and Dissertations

The Ultra Compact Combustor (UCC) promises to greatly reduce the size of a gas turbine engine’s combustor by altering the manner in which fuel is burnt. Differing from the common axial flow combustor, the UCC utilizes a rotating flow, coaxial to the engine’s primary axis, in an outboard circumferential cavity as the primary combustion zone. The present study investigates two key UCC facets required to further this combustor design. The first area of investigation is cooling of the Hybrid Guide Vane (HGV). This UCC specific hardware acts as a combustor center body that alters the exit flow angle and acts …

Introducing Concept Maps In Undergraduate Thermodynamics, Jessie Lofton

ASEE IL-IN Section Conference

Concept maps, also called mind maps, are a widely utilized educational tool. While numerous studies cite the benefits of concept mapping as a tool for student learning, the use of concept maps is more common in non-engineering disciplines. This study examines student perceptions and academic performance in an undergraduate, introductory Thermodynamics course for students majoring in Mechanical Engineering. The pedagogical approach includes incorporating student-developed concept maps, as well as an interactive study tool for First Law analysis. Qualitative and quantitative results are presented. Results are limited to a single institution and a small sample size of students. Future work will …

Exergetic Relationship Between The Thermal Properties Of Direct Contact Membrane Distillation, D. Perdue, L. Chen, L. Schaefer

Publications

Direct contact membrane distillation (DCMD) is a process that has shown promise within the field of desalination due to its less energy intensive methods and widespread applications. DCMD is a thermally driven microfiltration separation process that operates on the principle of vapor–liquid equilibrium conditions where heat and mass transfer occur simultaneously. Fundamentally, DCMD is based on a porous hydrophobic membrane separating the hot solution (feed) from the cold solution (permeate) where desalinated water condenses. The membrane interfacial temperatures determine the vapor pressure difference across the membrane. In this work, a direct simulation Monte Carlo analysis is employed to investigate how …

Use Of Penetrating Asphalt Emulsions To Address High-Void Pavement Areas, Andrew Eicher, Curt Higginbotham

Purdue Road School

Longitudinal joints are high in air voids due to compaction limitations. Lowering the void content of these areas improves the durability of the pavement. Project data indicate that rapid penetrating emulsion (RPE) fills the voids beneath the surface of the pavement, reducing air and water intrusion while maintaining surface texture, whereas traditional emulsions seal the surface only. Lab tests have been developed to quantify the penetrating ability of an emulsion and resistance to water exposure. Join us for a discussion.

Urea Functionalization Of Ultrasound-Treated Biochar: A Feasible Strategy For Enhancing Heavy Metal Adsorption Capacity, Baharak Sajjadi, James William Broome, Wei Yin Chen, Daniell L. Mattern, Nosa O. Egiebor, Nathan Hammer, Cameron L. Smith

Faculty and Student Publications

© 2018 Elsevier B.V. The main objective of a series of our researches is to develop a novel acoustic-based method for activation of biochar. This study investigates the capability of biochar in adsorbing Ni(II) as a hazardous contaminant and aims at enhancing its adsorption capacity by the addition of extra nitrogen and most probably phosphorous and oxygen containing sites using an ultrasono-chemical modification mechanism. To reach this objective, biochar physically modified by low-frequency ultrasound waves (USB) was chemically treated by phosphoric acid (H3PO4) and then functionalized by urea (CO(NH2)2). Cavitation induced by ultrasound waves exfoliates and breaks apart the regular …

Fluorescence Of Cdse/Zns Quantum Dots In Toluene: Effect Of Cyclic Temperature, Ting Chen, Weiling Luan, Shaofu Zhang, Fuqian Yang

Chemical and Materials Engineering Faculty Publications

Quantum dots (QDs) are the potential material for the application in optical thermometry, and have been successfully applied to solar cells, LEDs, bio-labeling, structural health monitoring, etc. In this paper, we study the fluorescence properties of CdSe/ZnS QDs in toluene under the action of heating-cooling cycles. The experimental results show that, in a heating-cooling cycle, increasing temperature causes red-shift of the emission peak and the decrease of the PL intensity, and decreasing temperature causes blue-shift of the emission peak and the increase of the PL intensity. The surface structures of the QDs likely are dependent on the cycle numbers, which …

Plenum-To-Plenum Heat Transfer Characteristics Under Natural Circulation In A Scaled-Down Prismatic Modular Reactor, Salman Mohammed Alshehri

Doctoral Dissertations

“Gas-cooled reactor (GCR) is being developed under the Next Generation Nuclear Plant Program (NGNP) in nuclear engineering studies. As the world searches for an energy source with high energy density, clean, abundant, and storable nature to avoid global warming issues, GCR seems to be a promising solution, particularly the possibility of producing hydrogen. Studying and developing the safety analysis and GCR technologies are required for the optimum design and safety of GCR system. Multiphase Reactors Engineering and Applications Laboratory (mReal) at Missouri University of Science and Technology (S&T) has developed a natural convection heat transfer test facility with one riser …

Computational Fluid Dynamics Modeling And Comparison Of Advanced Techniques For Heat Transfer Augmentation For Nuclear Applications, Salman Mohammed Alzahrani

Doctoral Dissertations

“Passive safety is the most important feature of NuScale’s reactor designs. Twist tape is one passive heat enhance heat technique. The present research investigated thermo-hydraulic characteristics of natural and forced convection of water under different configurations of twisted tape inserted in tube as well as NuScale rod bundles for uniform wall heat flux using computational fluid dynamics (CFD) using ANSYS Fluent 18.1. Results for twist tape inserted in tube under natural circulation showed that heat transfer enhanced and pressure drop increased to 28% and 102.8% over the plain tube respectively. Regularly spaced tapes, and different widths of the twisted tapes …

Characterization Of Aerosols In An Underground Mine, Arash A. Habibi

Doctoral Dissertations

“Diesel-powered engines are a common source of submicron carbon-rich particles. Characterizing morphological and physical attributes of diesel agglomerates is therefore of great importance to be able to identify the source and improve removal technology. Size-segregated sampling was conducted in two phases of underground experiments. Scanning transmission electron microscopy and fast mobility particle sizers were used to determine the size distribution of agglomerates based on particle mobility and projected area diameter. Controlled zone sampling test results were used to determine the morphological characteristics of agglomerates for specific types of diesel equipment both with and without removal strategies. Changes in fractal dimension, …

Capillary Forces In Partially Saturated Thin Fibrous Media, Ali Moghadam

Theses and Dissertations

Capillarity is often exploited in self-cleaning, drag reducing and fluid absorption/storage (sanitary products) purposes just to name a few. Formulating the underlying physics of capillarity helps future design and development of optimized structures. This work reports on developing computational models to quantify the capillary pressure and capillary forces on the fibrous surfaces. To this end, the current study utilizes a novel mass-spring-damper approach to incorporate the mechanical properties of the fibers in generating virtual fibrous structures that can best represent fibrous membranes. Such virtual fibrous structures are then subjected to a pressure estimation model, developed for the first time in …

Improving The Delivered Specific Impulse Of Composite Rocket Propellant Through Alteration Of Chemical Composition: Methodology And Parameters For Characterization Of Propellant And Validation Of Simulation Software Common To The Amateur Rocketry Community, Isaac O'Brien, Austin Ryan

Williams Honors College, Honors Research Projects

In this study, two solid composite rocket propellants were designed utilizing ProPEP, a rocket propellant formulation software common in the amateur and hobby rocketry communities. The two propellants were designed to optimize specific impulse relative to a literature propellant designed by 1020 Research Labs. The literature propellant was also tested in order to validate the design of experiment as well as the mixing and testing procedures. All three propellants, which includes the literature propellant RCS-P, and the two novel propellants AKR-P1 and AKR-P2 were characterized with static tests. The results of the static tests provide data on propellant performance and …

Reduction Of Nox Emissions In A Single Cylinder Diesel Engine Using Sncr With In-Cylinder Injection Of Aqueous Urea, Anthony Timpanaro

UNF Graduate Theses and Dissertations

The subject of this study is the effect of in-cylinder selective non-catalytic reduction (SNCR) of NO_x emissions in diesel exhaust gas by means of direct injection of aqueous urea ((NH₂)₂CO) into the combustion chamber. A single cylinder diesel test engine was modified to accept an electronically controlled secondary common rail injection system to deliver the aqueous urea directly into the cylinder during engine operation.

Direct in-cylinder injection was chosen in order to ensure precise delivery of the reducing agent without the risk of any premature reactions taking place. Unlike direct in-cylinder injection of neat water, …

Void Fraction Measurements In Large (0.3 M) Diameter Bubble Column Using Wire Mesh Sensor And Pressure Transducers- Effect Of Sparger, Afolabi Gabriel Ojo

Dissertations and Theses

The importance of the accurate temporal and spatial measurements of the two-phase flow parameters in bubble columns is very well known. The aim of this research work is to report the spatial measurements of the void fraction distribution in a 30 cm diameter cylindrical bubble column using Wire Mesh Sensor (WMS) tomography and Pressure Transducers. Pair of WMS sensors, with a 64×64 wire configuration of each sensor, were installed which are separated by a distance along the axis of the bubble column. Wire Mesh Sensors and PTs Data were collected for time-averaged and transient with a sampling frequency of 1000 …

Literature Survey Of Wet-Waste And Hydrothermal Carbonization System: A Comparative Evaluation, Ramat Olaide Yusuf

Dissertations and Theses

This thesis describes the process of Hydrothermal carbonization and a comparative assessment on recent work done on the process using different feedstocks such as Raw Apple (RA), Apple chip pomace (ACP), apple juice pomace (AJP), grape pomace (GP), macadamia nut-shell (MNS), Sewage Sludge (SS), Poultry Litter (PL) and Grape Marc (GM). The data obtained from the literature survey was compared with the data obtained by the CCL team on the SWPS gasifier (HTC of poultry litter) to obtain how carbon conversion efficiency, syngas composition, thermal efficiency, char production rate, gas production rate and energy utilization vary with carbonization process conditions, …

Void Fraction Measurements In A Large (0.3 M) Diameter Bubble Column Using Wire Mesh Sensors And Pressure Transducers: Effect Of Spargers, Afolabi G. Ojo

Dissertations and Theses

The importance of the accurate temporal and spatial measurements of the two-phase flow parameters in bubble columns is very well known. The aim of this research work is to report the spatial measurements of the void fraction distribution in a 30 cm diameter cylindrical bubble column using Wire Mesh Sensor (WMS) tomography and Pressure Transducers. Pair of WMS sensors, with a 64×64 wire configuration of each sensor, were installed which are separated by a distance along the axis of the bubble column. Wire Mesh Sensors and PTs Data were collected for time-averaged and transient with a sampling frequency of 1000 …

Modeling Electrospun Fibrous Materials, Sina Hassanpouryousefi

Theses and Dissertations

Electrospinning has been the focus of countless studies for the past decades for applications, including but not limited to, filtration, tissue engineering, and catalysis. Electrospinning is a one-step process for producing nano- and/or micro-fibrous materials with diameters ranging typically from 50 to 5000 nm. The simulation algorithm presented here is based on a novel mass-spring-damper (MSD) approach devised to incorporate the mechanical properties of the fibers in predicting the formation and morphology of the electrospun fibers as they travel from the needle toward the collector, and as they deposit on the substrate. This work is the first to develop a …

Towards Sustainable Production Of Chemicals And Fuels From The Fast Pyrolysis Of Waste Polyolefin Plastics, Ulises Gracida Alvarez

Dissertations, Master's Theses and Master's Reports

The increasing amount of plastic waste (PW) generation has become an important concern due to the leveled-off recycling rates. Therefore, governmental agencies around the world, including state governments in the United States, have proposed initiatives to minimize the amount of PW that is landfilled and encourage recycling or energy recovery. Circular economy is a strategy that attempts on reusing PW to produce new polymers while avoiding its disposal and the use of virgin material. Chemical recycling raises an interesting technology prospect due to the potential reduction of pollutant emissions and the establishment of a circular economy through the production of …

Experimental And Numerical Characterization Of Multiphase Subsurface Oil Release, Feng Gao

Dissertations

Subsurface oil release is commonly encountered in the natural environment and engineering applications and has received the substantial attention of researchers after the disastrous Deepwater Horizon Blowout oil spill in 2009. The main focus on the present research is to systematically study the hydrodynamics of underwater oil jet under a variety of conditions, including the effect of dispersant and different gas to oil ratios (GOR) by using experimental measurement as well as a Computational Fluid Dynamics (CFD) approach, from which the measured turbulent characteristics (e.g., velocity, turbulent kinetic energy, turbulence dissipation rate, etc.) of underwater oil jet are thoroughly examined …

Performance Of C2H4 Reductant In Activated-Carbon-Supported Mnox-Based Scr Catalyst At Low Temperatures, Guangli Liu, Dongtai Han, Jie Cheng, Yongshi Feng, Wenbin Quan, Li Yang, Kozo Saito

Mechanical Engineering Faculty Publications

Hydrocarbons as reductants show promising results for replacing NH₃ in SCR technology. Therefore, considerable interest exists for developing low-temperature (< 200 °C) and environmentally friendly HC-SCR catalysts. Hence, C₂H₄ was examined as a reductant using activated-carbon-supported MnOx-based catalyst in low-temperature SCR operation. Its sensitivity to Mn concentration and operating temperature was parametrically studied, the results of which showed that the catalyst activity followed the order of 130 °C > 150 °C > 180 °C with an optimized Mn concentration near 3.0 wt.%. However, rapid deactivation of catalytic activity also occurred when using C₂H₄ as the reductant. The mechanism of deactivation was explored and is …

Cfd Modeling Of Smoke Movement In An Atrium, Robin Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

The purpose of this paper is to better understand the behavior of smoke movement in an atrium. Thus gives first responders and civilians in and out of building a better understanding

With the advancements of modern technology, computers and softwares make simulation models possible such as fire models to simulate fire and smoke movements. In this paper, a computational fluid dynamic (CFD) software Fire Dynamic Simulator (FDS) is used to conduct a series of atrium tests to investigate the effectiveness of smoke exhaust systems. FDS solves the Navier-Stokes equations appropriate for low speed flows (Ma < 0.3) with an emphasis on smoke, heat transport and CO2 concentrations from fires. The default turbulence model used in FDS simulation is the Large Eddy Simulation (LES), which is the solution of Navier-Stokes equations at low speed.

The compartment tested was 9 …