Chemical Engineering Commons^™

Chitosan/Nonahydrate Gel Derived Fe-N-Doped Porous Carbon Sheet As High-Efficient Orr Electrocatalyst, Fan-Lu Meng, Xin-Bo Zhang, Jun-Min Yan

Journal of Electrochemistry

The chitosan/nonahydrate gel was used as a precursor to realize the uniform mixture of N-polymer and metal salt. After lyophilization treatment, the gel went through heat treatment and acid etch. Accordingly, the Fe-N-doped porous carbon sheet with homogenous composition and microstructure was prepared. Compared with the commercial Pt/C catalyst, the Fe-N-doped porous carbon sheet exhibited more positive onset potential and half-wave potential, higher current density, and especially, excellent durability. The power density of 318 mW·cm^-2 was obtained in alkaline fuel cell with the Fe-N-doped porous carbon sheet as a cathode catalyst, which is higher than 267 mW·cm^-2 with …

Synthesis Of Ultrathin Co3O4 Nanoflakes Film Material For Electrochemical Sensing, Hui-Juan Wang

Journal of Electrochemistry

Ultrathin cobalt oxide (Co₃O₄) nanoflakes film material was synthesized by using an electro-deposited cobalt layer as a raw material through a simple oxidation method and followed by a heat treatment at 350 ^oC. The physical characterizations of the Co₃O₄ nanoflakes film were performed by scanning electron microscopy (SEM), X-ray diffraction (XRD) and transmission electron microscopy (TEM) technologies, and the electrochemical activity was measured by cyclic voltammetry (CV). As a promising material for electrochemical sensing, the as-synthesized ultrathin Co₃O₄ nanoflakes film material exhibited excellent electrochemical activity for H₂O …

Design And Synthesis Of Dynamic Covalent Polymer Scaffolds With Controlled Architectures, Emily Annette Hoff

Dissertations

The design and synthesis of functional, controlled polymer architectures is essential to the development of new materials with precise and tailorable properties or applications. The work described in this dissertation focuses on the development of controlled polymer architectures with dynamic linkages for the design of multifunctional materials and surfaces via robust, efficient, and stimuli-responsive strategies.

In Chapter III, a post-polymerization modification strategy based on ambient temperature nucleophilic chemical deblocking of polymer scaffolds bearing N-heterocycle blocked isocyanate moieties is reported. Room temperature RAFT polymerization of three azole-N-carboxamide methacrylates, including 3,5-dimethyl pyrazole, imidazole, and 1,2,4-triazole derivatives, afforded reactive polymer scaffolds …

The Study Of Dynamical Electrochemical Impedance Spectroscopy For Oxygen Reduction Reaction On Pt/C Catalyst, Kun-Ming Shi, Jian-Wei Guo, Jia Wang

Journal of Electrochemistry

With joint techniques of rotating disc electrode(RDE) and electrochemical impedance spectroscopy(EIS), and further establishment on equivalent circuit model, this paper studied oxygen reduction reaction(ORR) on commercial Pt/C catalyst in acid medium. Our results found that the dynamical interface on Pt/C consists of two independent processes: 1) the PtO reduction from Pt surface, 2) the new PtO formation from ORR, thus providing key clues for catalyst stability and activity. This also implied that the dynamical interface facilitates reconstruction for porous electrode, and matches with mass transfer. One important issue is discovered that at high overpotential, the high reaction rate for ORR …

Template-Assisted Hydrothermal Synthesis Of Nio@Co3O4 Hollow Spheres With Hierarchical Porous Surfaces For Supercapacitor Applications, Wen Zhou, Xue-Feng Lu, Ming-Mei Wu, Gao-Ren Li

Journal of Electrochemistry

Hollow structures have shown great potentials in a variety of important applications, such as energy conversion and storage. In order to further enhance the performance, the rational design of hollow structures with higher complexity in terms of composition and structure is highly desirable and still remains a great challenge. In this work, an efficient strategy was established for the fabrication of novel NiO@Co₃O₄ hollow spheres (HSs) with hierarchical porous surfaces by silica spheres template-assisted hydrothermal synthesis. The as-fabricated NiO@Co₃O₄ HSs showed high specific surface area of 219.68 m²·g^-1, and significant …

Continuous Synthesis And Condition Exploration Of Precursor Ni1/3Co1/3Mn1/3(Oh)2 Ternary Cathode Material, Zhi-Jun Jiang, Ya-Li Zhang, Qian Wang, Hui Zhang

Journal of Electrochemistry

Commercial LiNi_1/3Co_1/3Mn_1/3(OH)₂ ternary material is generally prepared by a combination of co-precipitation and solid state reaction method. The particle size distribution and morphology of Ni_1/3Co_1/3Mn_1/3(OH)₂ precursor have a great impact on the electrochemical performance of LiNi_1/3Co_1/3Mn_1/3O₂. In this work, the precursor Ni_1/3Co_1/3Mn_1/3(OH)₂ ternary cathode material was prepared by co-precipitation method with MnSO₄, NiSO₄, and CoSO₄ as raw materials, NaOH as a precipitating agent and NH_{3 …}

Effect Of Surface Treatment On Liquid Adhesion Inside 3-D Structures, Madani A. Khan, Jeffrey Alston, Andrew Guenthner, Jacob Zavala

STAR Program Research Presentations

This study explores the relationship between chemical surface treatments on the interior of glass tubes and their resistance to fluid flow. By treating the interior of the tubes with functional silanes we can decrease or increase the interaction of the tube walls with the fluid column, which translates to changes in fluid column height for a given pressure differential. Resistance to fluid flow is quantified by using the tubes as integral parts of a barometric pressure column and measuring the changes in column height as the fluid is pulled into the tube by a set pressure differential. The barometric pressure …

Hydrothermal One-Step Synthesis Of Layered Nickel/Cobalt Double Hydroxide With Using Shape-Directing Agent And Homogeneous Precipitating Agent, Li-Wei Zhu, Yun-Hai Yan, Hui Jia, Run-Fen Liang

Journal of Electrochemistry

Nickel/cobalt double hydroxide (Ni/Co-DH) has been prepared by facile hydrothermal one-step synthesis method using hexamethylene tetramine (HMT) as a homogeneous precipitating agent and cetyltrimethylammonium bromide (CTAB) as a shape-directing agent. With the hydrolysis of HMT and the use of CTAB, the Ni/Co-DH could be synthesized without additional alkali source, and in the meantime, the Ni/Co-DH exhibited a controlled mesopore size of 13.4 nm and a large BET surface area of 93.6 m² •g^-1 . The X-ray diffraction (XRD) pattern displays that the Ni/Co-DH existed as a mixture of α-Ni(OH)₂-β-Co(OH)₂. The scanning electron microscope (SEM) …

Reduced Graphene Oxide (Rgo) Hollow Network Cages For High-Performance Electrochemical Energy Storage, Chi Zhang, Xu-Jun He, Gao-Ren Li

Journal of Electrochemistry

The reduced graphese oxide (RGO) hollow network cages were synthesized via zinc oxide (ZnO) template-assisted electrodeposition. The as-prepared RGO hollow network cages exhibited the multi-level architectures, from nano sheets, porous structures, networks, to 3D microscaled hollow cages, which can simultaneously optimize transport of electroactive species, utilization rate of electrode material, and super capacitive performance. Electrochemical measurements confirmed the superior performance of RGO hollow network cages for supercapacitors (SCs), such as high Csp (393 F⋅g^-1 at 1.0 A⋅g^-1), excellent rate capability (21.2% Csp loss from 1.0 to 20 A⋅g^-1), and superior cycling stability (< 1% Csp loss after 10000 cycles).

Synthesis, Structural Diversity, And Redox Control Of Cyclometalated Monoruthenium Complexes, Zhong-Liang Gong, Jiang-Yang Shao, Yu-Wu Zhong

Journal of Electrochemistry

Cyclometalated ruthenium complexes have received increasing attractions recently due to their excellent redox and photophysical properties. One structural feature of these complexes is that there is a ruthenium-carbon (Ru-C) σ bond presented in the molecule. Three common methods, namely, the “late metalation”, “early metalation”, and “transmetalation” methods, for the synthesis of cyclometalated ruthenium complexes are discussed and summarized. General strategies for the design of cyclometalating ligand and cyclometalated ruthenium complexes are introduced. By using different ancillary ligands, such as pyridine, imidazole, triazole, and pyrimidine, a great number of ruthenium complexes can be prepared. The presence of the Ru-C bond significantly …

Developments Of Photo-Assisted Fuel Cells, Ling-Ling Zhang, Shao-Jun Dong

Journal of Electrochemistry

The exploitation and utilization of fossil fuels have led to serious energy crisis and environmental pollution. In this case, the development of renewable energy is an alternative to traditional energy consumption. Fuel cells (FCs) can convert chemical energy into electricity via the electrochemical reaction, which is green and environment-friendly. Photo-assisted FCs integrate photo-responsive components into FCs, leading to the dual routes of energy conversion including light energy to electricity and chemical energy to electricity, and thus, improving the energy utilization efficiency. The development of photo-assisted FCs is significant for practical application and promising to solve the coming energy crisis. In …

Special Issue: Electrocatalyst And Electrocatalysis In Fuel Cells Preface, Zi-Dong Wei

Journal of Electrochemistry

/

Recent Progress In Non-Precious Metal Oxygen Reduction Reaction Catalysts With An Encapsulation Structure, Mei-Ling Xiao, Jian-Bing Zhu, Chang-Peng Liu, Jun-Jie Ge, Wei Xing

Journal of Electrochemistry

Platinum-based materials, the state-of-the-art catalysts for fuel cells, suffer from prohibitive costs, limited resources and insufficient durability. Accordingly, tremendous efforts were made in searching for efficient, durable and inexpensive alternatives to precious-metal electrocatalysts for the oxygen reduction reaction (ORR). Transition-metals (Fe, Co)/nitrogen co-doped hybrids, heteroatom (N, P, S, F, et al) doped carbons and composites with transition-metals encapsulated in graphitic layers are reported as the most efficient non-precious metal ORR catalysts. Among the various non-precious metal ORR catalysts, transition-metals encased in graphitic layer catalysts are a novel type of catalysts for ORR with high activity and durability, and thus, the …

Dynamic Simulation Of Oxygen Reduction Reaction In Pt/C Electrode For Proton Exchange Membrane Fuel Cells, Shang Li, Fen Zhou, Lei Chen, Mu Pan

Journal of Electrochemistry

It is an urgent need to reduce the Pt loading in electrode for practical fuel cell applications worldwide. Herein, we theoretically investigate the oxygen distribution, generated current, and minimum Pt loading of Pt/C electrode for practical applications based on kinetic model of oxygen reduction reaction. The results indicate that with increasing electrode effective thickness to 40 mm, serious concentration polarization is expected for Pt/C electrode. To generate a power density of 1.4 W⋅cm^-2 (2.1A⋅cm^-2@0.67 V) for fuel cell, the cathode catalyst layer thickness in PEMFC should be as thin as 3 mm. The minimum Pt loading will …

Multi-Scaled Carbon Supported Platinum As A Stable Electrocatalyst For Oxygen Reduction Reaction, Yu-Ping Li, Lu-Hua Jiang, Su-Li Wang, Gong-Quan Sun

Journal of Electrochemistry

The stability of carbon supports is essential for electrocatalysts of fuel cells. Herein, the mesoporous carbon with the high graphitic degree (highly graphitic mesoporous carbon, HGMC) was synthesized by using resorcinol as the carbon precursor, SiO₂ as the templates and urea as the reducing agent. The as-prepared HGMC was characterized by XRD, Raman spectroscopy, TEM, N2 adsorption. The stability of HGMC was evaluated by mimicking the start-up/shut-down conditions of fuel cells in a three-electrode system referring to the NREL standard. The obtained HGMC is of moderate surface area (187.4 m²•g^-1) and is chemically stable under …

Recycling Mf Solid Waste Into Mesoporous Nitrogen-Doped Carbon With Iron Carbide Complex In Graphitic Layers As An Efficient Catalyst For Oxygen Reduction Reaction, Can-Yun Zhao, Lin Huang, Yong You, Ying-Fang Yao, Xiao-Gang Su, Hong Wan, Jian-Guo Liu, Cong-Ping Wu

Journal of Electrochemistry

Nitrogen-doped carbon materials with iron ions are known as catalytic growth agents for the oxygen reduction reaction (ORR) in fuel cells, but the design and synthesis of high-performance and low-cost catalysts still remain a significant challenge. Herein, we present a cost-effective approach to dispose of MF solid waste as the precursor for the synthesis of MCFes catalyst with the favorable structure features such as the high specific surface area, abundant active sites and suitable pore structure. The results showed that the MCFe-10/10/2 had specific surface area as high as 780.7 m²•g^-1 and high efficient catalytic activity comparable …

Recent Progresses In Molybdenum-Based Electrocatalysts For The Hydrogen Evolution Reaction, Ze-Xing Wu, Jie Wang, Jun-Po Guo, Jing Zhu, De-Li Wang

Journal of Electrochemistry

Electrochemical catalytic production of hydrogen has been considered as a promising and sustainable strategy for clean and renewable energy technologies. Molybdenum-based non noble metal catalysts for the hydrogen evolution reaction have attracted extensive attention due to its effective catalytic performance. In this review, the recent progresses in molybdenum-carbide, phosphide, nitride and sulfide electrocatalysts are presented. In addition, the strategies to improve the catalytic performance are analyzed and the prospects for the future development trends are expected.

Rambling Between "Zhong Yong" And "Catalysis", Zi-Dong Wei

Journal of Electrochemistry

“Zhong Yong” represents a traditional Chinese wisdom, which was first proposed by Confucius and continuously richened by his followers. “Zhong Yong” pursues the balances among all kinds of contradictions, and insists that neither “too much” nor “not enough” is good. For a successful catalyst, on which the adsorption of reactants must be not so strong and not so weak either. On this point of view, there are the same pursuits for “Zhong Yong” and catalysis. In this paper, the author starts his story with a conversation between Confucius and his student, followed by 3 interesting stories happening in the ancient …

Synthesis Of Structurally Ordered Platinum-Iron Catalysts With Enhanced Oxygen Reduction Reaction Activity, Ye-Zheng Cai, Ming-Chuan Luo, Fang-Hui Wang, Zhao-Nan Sun, Hong Zhu

Journal of Electrochemistry

To improve oxygen reduction reaction catalytic activity of the precious metals platinum for fuel cell, the precursors of carbon-supported structurally disordered platinum-iron alloy (D-Pt₃Fe/C and D-PtFe/C) catalysts with different compositions were synthesized via a modified polyol reduction method. Then, by optimizing the annealing conditions in the inert gas, we turned the structurally disordered platinum-iron alloy to the structurally ordered platinum-iron alloy (O-Pt₃Fe/C and O-PtFe/C) catalysts. The structural characterizations of the as-prepared catalysts were performed by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), inductively coupled plasma-atomic emission spectroscopy (ICP-AES), and X-ray photoelectron spectroscopy (XPS). The results …

Mini-Review: Possible Applications Of Scanning Electrochemical Microscopy (Secm) In Characterizations Of Oxygen Reduction Reaction And Oxygen Evolution Reaction, Xing-Xing Chen

Journal of Electrochemistry

Scanning electrochemical microscopy (SECM) has been proved to be a unique technique for combinatorial screening of localized phenomena for different electrocatalysts potentially used in new energy conversion and storage systems. This mini-review provides a brief summary of different SECM working modes, such as direct mode, feedback mode, generation-collection mode, redox competition mode and noise mode, which are especially applied for characterizing the oxygen reactions. Particularly, a series of important development in SECM screening of electrocatalysts for oxygen reduction reaction and oxygen evolution reaction from the author and W. Schuhmann’s group in Germany has been highlighted and overviewed. Finally, some prospects …

Syntheses Of Carbon Paper Supported High-Index Faceted Pt Nanoparticles And Their Performance In Direct Formic Acid Fuel Cells, Long Huang, Mei Zhan, Yu-Cheng Wang, Yan-Fen Lin, Shuo Liu, Ting Yuan, Hui Yang, Shi-Gang Sun

Journal of Electrochemistry

Direct formic acid fuel fuels (DFAFCs) are promising energy source for portable electronic devices. Palladium (Pd) is more active than platinum (Pt) for the formic acid electrooxidation. However, the stability of Pd is much poorer than that of Pt. Unfortunately, the ultra-low natural abundance of the Pt makes it extremely expensive and limits its application as a fuel cell catalyst. Boosting both the activity and stability of Pt nanoparticles to enhance their efficiency is urgent. As previous works illustrated, nanoparticles enclosed with high-index facets usually bare a higher activity toward fuel cell related reactions than those nanoparticles with low-index facet. …

Preparation And Performance Of 3d Graphene Type Porous Carbon Employing Nano Fe(Oh)3 As Template For Oxygen Reduction Catalyst, Chong-Yun Sun, Zhong-Fang Li, Xue-Wei Lu, Xi-Zhan Zhong, Yu-Rong Liu

Journal of Electrochemistry

The 3D graphene type porous carbon was prepared using coal tar pitch as carbon source and nano Fe(OH)₃ as template. Optimal conditions for the catalytic oxygen reduction performance were determined as: the mass ratio of coal tar, nano Fe(OH)₃ and KOH is 6:8:4; the pyrolysis temperature is 800 ^oC. SEM images show that the products have uniformly porous structure. TEM images demonstrate that the products are porous with foam shapes. HRTEM images further indicate that the products have formed several-layers 3D graphene structure, which are also supported by XRD and Raman data, and the pore size mainly …

Nitrogen, Fluorine Co-Doped Silk-Derived Carbon For Electrochemical Oxygen Reduction With High Performance In Alkaline Solution, Fang-Fang Liu, Hong-Liang Peng, Shi-Jun Liao

Journal of Electrochemistry

A high-performance, doped carbon-based catalyst was synthesized by pyrolyzing hydrothermally treated silkworm cocoon. The effects of preparation conditions and fluorine promotion on various catalysts’ performance were investigated. The catalyst prepared under optimal conditions and doped with nitrogen and fluorine possessed the high specific surface area of more than 1000 m^2⋅g^-1 and contained 3.5 and 7.3% (by mass, the same below) N and F, respectively. The activity of the catalyst toward oxygen reduction reaction in an alkaline medium was comparable to that of commercial Pt/C, showing both superior tolerance to methanol poisoning and better durability. Doping with fluorine …

Optimizing Chemical & Rheological Properties Of Rejuvenated Bitumen, Dominic Nguyen, Hamzeh Haghshenas Fatmehsari, Santosh Kommidi, Yong-Rak Kim

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Bitumen has long been a material used in the construction of roadways, yet new pavement only consists of low fractions of recycled materials due to poor compatibility of aged bitumen and new materials. Thus, rejuvenators, chemical additives, have been used in an attempt to re-balance the chemical composition and restore the physical properties of aged bitumen back to its virgin state. A fundamental understanding of how one particular rejuvenator, soybean oil, revitalizes bitumen was investigated using a multi-scale approach.

Fourier-transform infrared spectroscopy (FTIR) was used to determine the changes in chemical properties of pure and rejuvenated virgin and aged samples. …

High Temperature Electrochemical Engineering And Clean Energy Systems, Brenda L. Garcia-Diaz, Luke Olson, Michael Martinez-Rodriguez, Roderick Fuentes, Hector Colon-Mercado, Josh Gray

Journal of the South Carolina Academy of Science

Global power demand is projected to more than double by 2050 and meeting this increased power demand will require maintaining or increasing power output from all existing energy sources while adding a large amount of new capacity. The power sources that have the greatest opportunity to fulfill this demand gap over this time period are clean energy sources including solar and nuclear power. One of the areas of expertise that SRNL has been applying to help with a variety of clean energy technologies is in high temperature electrochemistry. Savannah River National Laboratory (SRNL) in collaboration with industrial and university partners …

Electrochemical Syntheses Of Graphene And Its Composites, Bo Zhao, Li Jiang, Ming-Hui Yuen, Xian-Zhu Fu, Rong Sun, Ching-Ping Wong

Journal of Electrochemistry

Graphene is a kind of ideal two-dimensional flat carbon nanomaterials which have unique chemical and physical properties. The attractive potential applications must be based on the high quality mass production of graphene. However, it remains a huge challenge. An electrochemical approach is a fast, environmental friendly and easy-operating method. single- or multi-layered graphene flakes can easily be produced in short periods of time. In this review, the structure, properties and preparation methods of graphene are first introduced. Accordingly, the electrochemical approaches used for the productions of graphene flakes, graphene/inorganic nanocomposites, graphene/polymer composites and graphene analogues are highlighted. Finally, challenges and …

Synthesis Of Fe, N-Doped Graphene/Carbon Black Composite With High Catalytic Activity For Oxygen Reduction Reaction, Chi Chen, Zhi-You Zhou, Xin-Sheng Zhang, Shi-Gang Sun

Journal of Electrochemistry

Oxygen reduction reaction (ORR) is a bottleneck for improving the efficiency of proton-exchange membrane fuel cells as a cathode reaction due to its sluggish kinetics. The exploitation of low cost and high performance non-precious metal catalysts such as Fe/N/C based materials toward ORR has attracted extensive attentions. In this work, the Fe, N-doped graphene nanosheets/carbon black composite was prepared by hydrothermal polymerization and followed by a twice-heat-treatment procedure using 2-aminoimidazole as an N precursor, FeCl₃ as an Fe precursor and KJ600 carbon black as a support. The TEM images revealed that the graphene nanosheets were separated by carbon black …

Electricity Generation Of Microbial Fuel Cell Using Stainless Steel Mesh As Cathode, Hong-Yan Dai, Hui-Min Yang, Xian Liu, Xuan Jian, Xiu-Li Song, Zhen-Hai Liang

Journal of Electrochemistry

In the present work, a dual-chamber microbial fuel cell (MFC) was constructed with aeration tank sludge as an inoculum, carbon felt as an anode and stainless steel mesh without any modification as a cathode. The influence of the cathode size was investigated in terms of voltage output, power generation and electrochemical impedance. The long-term durability of the stainless steel mesh cathode was also evaluated. Results showed that the stainless steel mesh exhibited satisfactory long-term durability as MFC cathode. When the stainless steel mesh size was 2 × 2 cm², the maximum output voltage, power density, the internal resistance …

Electrochemical Detection Of Hydrogen Peroxide At Aunps Modified Electrode Using P-Hydroxyphenylboronic Acid As A Precursor, Chun-Yan Wang, Xiao-Qiu Liu, Ying-Xin Qi

Journal of Electrochemistry

We developed a new method for electrochemical detection of hydrogen peroxide (H₂O₂) based on boronate oxidation of p-hydroxyphenylboronic acid. This method using p-aminophenol which is produced from the reaction of H₂O₂ and p-aminophenylboronic acid as a well electrochemical probe, combined with a gold nanoparticles (AuNPs) modified electrode for an indirect detection of H₂O₂. Because of the large surface area and enhanced electrocatalytic behavior by the AuNPs modified electrode, the detection sensitivity was improved. The method could detect H₂O₂ in the concentration range of 1 ~ 100 …

The Study On Comparison Of Electrochemical Performance In Microbial Fuel Cell With Glucose And Sodium Acetate Acting As Substrates, Lei Fan, Yu Zhao, Ting Li, Qin-Bo Yuan, En-Zhi Wang, Xiao-Bin Wang, Jun-Wen Wang

Journal of Electrochemistry

By inoculating aerobic sludge and anaerobic sludge from the sewage treatment plant, two sets of dual-chamber microbial fuel cells (MFCs) were built with either glucose or sodium acetate acting as a substrate. Accordingly, the electrochemical performances of MFCs were explored with the concentration of the substrates being 0.0335 mol⋅L^-1. The results of the comparative study in glucose system and sodium acetate system showed that the impedance values of anodic half cell were 222 Ω for glucose and 213.67 Ω for sodium acetate, implying no significant effect on the internal resistance in battery with the different substrates. The exchange …