Chemical Engineering Commons^™

Electrochemical Advanced Treatment Of Desulfurization Wastewater From Coal-Fired Power Plants, Ju-Cai Wei, Juan Yi, Xu Wu

Journal of Electrochemistry

Zero-emission of desulfurization wastewater is one of the main demands for coal-fired power plants. As typical high salinity wastewater, it is hard to purify the desulfurization wastewater from coal-fired power plants through traditional physicochemical treatment or biochemical treatment, e.g., COD and Cl^–. A high concentration of Cl^– ion in desulfurization wastewater restricts wastewater reuse and zero-emission. Electrochemical technology is an attractive method for high salinity wastewater zero-emission, which provides a versatile, efficient, cost-effective, easily automatable, and clean industrial process. For advanced treatment of effluent after triple box process treatment in power plants, this paper reports an electrochemical …

Seeding Effects Of Submicron Caal-No3 Ldh Particles On The Hydration And Properties Of Portland Cement And Sulfoaluminate Cement Pastes, Sukanta K. Mondal, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

Layered double hydroxide (LDH) is reported to improve the durability of concretes, primarily due to its ability to exchange anionic species, including chloride, which is implicated in corrosion-driven durability issues. However, there is no comprehensive study investigating the effect of LDH on the properties of different cement systems at both early and mature ages. in this study, the early age and mature age properties of Portland cement (OPC) and calcium sulfoaluminate (CSA) cement pastes seeded with submicron-sized calcium aluminum-NO3 LDH (CaAl-NO3 LDH) were investigated. the effects of the 1–5%mass dosage of LDH on the hydration of both cement systems were …

Thermal Frontal Polymerization – Applications In Coatings And Composites, Maria Martinez

LSU Doctoral Dissertations

Thermal frontal polymerization has long been used as a method to cure composites and coatings. However, this is the first time these applications have been used without the use of a catalyst, for the case of composites and coatings.

Chapter 2 discusses how to optimize cure-on-demand, thin layer coatings, using frontal polymerization. Previously, for the use of curing thin layer coating using thermal FP, it was known to just make the formulation viscous enough, as this would prevent premature quenching caused by heat loss. It was discovered that for a given layer thickness, a minimum viscosity and initiator concentration were …

Shorting At Long Duration: Impact Of Extended Discharge Capacity On Battery Solid Electrolytes, Ryan C. Hill, Amanda S. Peretti, Leo J. Small, Erik D. Spoerke, Yang-Tse Cheng

Chemical and Materials Engineering Faculty Publications

Long-duration energy storage (LDES) is critical to a stable, resilient, and decarbonized electric grid. While batteries are emerging as important LDES devices, extended, high-power discharges necessary for cost-competitive LDES present new materials challenges. Focusing on a new generation of low-temperature molten sodium batteries, we explore here unique phenomena related to long-duration discharge through a well-known solid electrolyte, NaSICON. Specifically, molten sodium symmetric cells at 110 ° C were cycled at 0.1 A cm−2 for 1–23 h discharges. Longer discharges led to unstable overpotentials, reduced resistances, and decreased electrolyte strength, caused by massive sodium penetration not observed in shorter duration discharges. …

Recent Advances In Solar Photo(Electro)Catalytic Nitrogen Fixation, Jun-Bo Ma, Sheng Lin, Zhiqun Lin, Lan Sun, Chang-Jian Lin

Journal of Electrochemistry

Ammonia (NH₃) is an essential chemical in modern society. It is currently produced in industry by the Haber-Bosch process using H₂ and N₂ as reactants in the presence of iron-based catalysts at high-temperature (400–600 ^oC) and extremely highpressure (20–40 MPa) conditions. However, its efficiency is limited to 10% to 15%. At the same time, a large amount of energy is consumed, and CO₂ emission is inevitably. The development of a sustainable, clean, and environmentally friendly energy system represents a key strategy to address energy crisis and environmental pollution, ultimately aiming to achieve carbon neutrality. …

Highly Efficient Dopamine Sensing With A Carbon Nanotube-Encapsulated Metal Chalcogenide Nanostructure, Harish Singh, Jiandong Wu, Kurt A.L. Lagemann, Manashi Nath

Chemical and Biochemical Engineering Faculty Research & Creative Works

Carbon nanotube-encapsulated nickel selenide composite nanostructures were used as nonenzymatic electrochemical sensors for dopamine detection. These composite nanostructures were synthesized through a simple, one-step, and environmentally friendly chemical vapor deposition method, wherein the CNTs were formed in situ from pyrolysis of a carbon-rich metallo-organic precursor. The composition and morphology of these hybrid NiSe2-filled carbon nanostructures were confirmed by powder X-ray diffraction, Raman, X-ray photoelectron spectroscopy, and high-resolution transmission electron microscopy images. Electrochemical tests demonstrated that the as-synthesized hybrid nanostructures exhibited outstanding electrocatalytic performance toward dopamine oxidation, with a high sensitivity of 19.62 μA μM-1 cm-2, low detection limit, broad linear …

Biomolecular Crystals As Functional Materials, Fahmeed Khan Sheehan

Dissertations, Theses, and Capstone Projects

The field of supramolecular chemistry has undergone significant evolution over the last few decades, progressing from fundamental studies of self-assembling systems to the rational design of functional materials with exceptional properties. Among these materials, short peptides have emerged as a chemically simple yet highly versatile class of biomimetic compounds. Initially, short peptides were used as model systems to understand larger protein interactions. As the field progressed, short peptides were found to have exceptional functionality, and are now explored as functional nanomaterials for diverse applications. In many cases, short peptide materials have displayed properties not found in biology, in some cases …

Monodispersed Cu-Tcpp/Cu2O Hybrid Microspheres: A Superior Cascade Electrocatalyst Toward Co2 Reduction To C2 Products, Zi-Xuan Wan, Aidar Kuchkaev, Dmitry Yakhvarov, Xiong-Wu Kang

Journal of Electrochemistry

The electrochemical conversion of carbon dioxide (CO₂) into valuable chemicals is a feasible way to mitigate the negative impacts of overmuch CO₂ emissions. Porphyrin-based metal organic frameworks (MOFs) are expected to be used for selective and efficient electrochemical CO₂ reduction (ECR) with porous structure and ordered active sites. Herein, we report the synthesis of a monodispersed and spherical organic/inorganic hybrid Cu-TCPP@Cu₂O electrocatalyst composed of Cu-TCPP (TCPP=tetrakis (4-carboxyphenyl) porphyrin) and Cu₂O, where TCPP plays significant roles in regulating the morphology. In-situ formed Cu during ECR process in combination with Cu-TCPP (Cu-TCPP@Cu) can suppress …

Rational Design Of Heterostructured Nanomaterials For Accelerating Electrocatalytic Hydrogen Evolution Reaction Kinetics In Alkaline Media, Hai-Bin Ma, Xiao-Yan Zhou, Jia-Yi Li, Hong-Fei Cheng, Ji-Wei Ma

Journal of Electrochemistry

Owing to the merits of high energy density, as well as clean and sustainable properties, hydrogen has been deemed to be a prominent alternative energy to traditional fossil fuels. Electrocatalytic hydrogen evolution reaction (HER) has been considered to be mostly promising for achieving green hydrogen production, and has been widely studied in acidic and alkaline solutions. In particular, HER in alkaline media has high potential to achieve large-scale hydrogen production because of the increased durability of electrode materials. However, for the currently most prominent catalyst Pt, its HER kinetics in an alkaline solution is generally 2–3 orders lower than that …

Investigation Of Space Charge Effects On Co2 Electrocatalytic Reduction On Gd-Doped Ceria Via Scanning Kelvin Probe And Model-Based Bayesian Analysis, Alejandro Mejia

Graduate Theses, Dissertations, and Problem Reports (ETD)

In studying novel energy conversion and storage systems, such as high-temperature electrolysis, numerous underlying fundamental physical processes remain unclear or inadequately understood. Among these, the modeling and comprehension of surface reaction mechanisms, coupled with the intricate effects of space‑charge interfaces, remains an unclear and challenging area of research.

The work of this dissertation involves the development of a 2D finite element analysis model, leveraging the robust MOOSE framework from INL. This model, featuring inhomogeneous defect thermodynamics for near-surface chemistry, formulated through Poisson‑Cahn variational theory, has been exploited for studying the electrocatalytic reduction of CO₂ on gadolinia doped ceria. The …

Data-Driven Modeling Of Oxygen Kinetics In La0.6sr0.4co0.2fe0.8o3−Δ (Lscf) For High-Temperature Reduction Of Co2 In An Electrolysis Cell, Ferron Campbell

Graduate Theses, Dissertations, and Problem Reports (ETD)

Electrolysis systems are critical to several societal applications, particularly energy storage and conversion. Developing these systems requires a detailed knowledge of the chemistry and thermodynamics of the materials used in the electrolysis cell. This work focuses on using embedded scientific machine learning as an efficient way to build an interpretable model for the reaction and transport kinetics in the LSCF electrode, whose performance directly influences the electrolysis system’s performance. The models developed in this study are trained using the publicly available machine learning package, FoKL-GP. This package incorporates a robust Gibbs sampler that employs a forward variable selection process to …

Novel Re-Crosslinkable Preformed Particle Gels (Rppg) For Parent- And Infill-Well-Fracture Interactions Mitigation, Xiaojing Ge, Adel Alotibi, Ahmed Al-Hlaichi, Yanbo Liu, Tao Song, Junchen Liu, Baojun Bai, Thomas P. Schuman

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Hydraulic fracturing treatments in unconventional infill (or "child") wells can be significantly affected by depletion from existing parent-well, resulting in asymmetrical fracture growth. These issues may lead to excessive load-water production, proppant deposition, casing deformation in the parent well, and unbalanced stimulation of infill wells. To mitigate these effects, various strategies have been proposed, including the use of far-field diverters in child wells and repressurization of parent wells. Additionally, an increasingly popular strategy involves injecting near-wellbore diverters to temporarily plug entry points into the parent wellbores during frac operations on infill wells. To achieve better application, a novel low-cost, self-degradable, …

Change Of Metal Oxidation State At High Temperature, Impact Of Temperature And Reactive Gases, Yegor Nikitin

Dissertations and Theses

The fundamental understanding of gas-solid reactions enables a wide range of applications to be developed and improved. Specifically, the use of metal-based materials is critical to ensuring robust, safe, and long-term operations. For example, in power systems where boilers are used to generate steam for heat or electricity generation the use of stainless metal alloys is critical to allow high quality steam to be produced in a very harsh environment. Alternatively, in catalysis, the use of metal doped heterogeneous catalysts are essential in achieving selectivity and conversion performance for chemical synthesis to emissions abatement. Typically, these metal alloys must withstand …

Lessons Learned From Laboratory Study And Field Application Of Re-Crosslinkable Preformed Particle Gels Rppg For Conformance Control In Mature Oilfields With Conduits/Fractures/Fracture-Like Channels, Baojun Bai, Thomas P. Schuman, David Smith, Tao Song

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

This Paper Surveys the Role of Re-Crosslink able Preformed Particle Gels (RPPG) in Addressing Conformance Challenges within Mature Oilfields. Despite Widespread Preformed Particle Gel (PPG) Application in 15,000+ Wells, their Limitations in Sealing Fractures and Conduits Prevalent in Mature Reservoirs Have Driven the Development of RPPG Formulations. Synthesized in Various Sizes from Micrometer to Millimeter Levels, These Environmentally Friendly RPPGs Are Tailored for Diverse Reservoir Conditions. Findings Showcase the Successful Laboratory-Scale Creation and Upscaling of RPPG Products, Offering Adaptability to Temperatures from 20 to 175°C, Customizable Sizes, Swelling Ratios (5 to 40 Times), and Re-Crosslinking Times Spanning Minutes to Days. …

Electrochemical Performance Of Porous Ceramic Supported Tubular Solid Oxide Electrolysis Cell, Heng-Ji Wang, Wen-Guo Chen, Zhou-Yi Quan, Kai Zhao, Yi-Fei Sun, Min Chen, Ogenko Volodymyr

Journal of Electrochemistry

Solid oxide electrolysis cell (SOEC) is an efficient and clean energy conversion technology that can utilize electricity obtained from renewable resources, such as solar, wind, and geothermal energy to electrolyze water and produce hydrogen. The conversion of abundant intermittent energy to hydrogen energy would facilitate the efficient utilization of energy resources. SOEC is an all-ceramic electrochemical cell that operates in the intermediate to high temperature range of 500–750 ℃. Compared with traditional low temperature electrolysis technology (e.g., alkaline or proton exchange membrane cells operating at ~100 ℃), the high-temperature SOEC can increase the electrolysis efficiency from 80% to ~100%, providing …

Combined Risk Based Inspection And Fault Tree Analysis For Repetitive 3-Phase Line Piping Leakage At West Java Offshore Topside Facility, Dona Yuliati, Akhmad Herman Yuwono, D. Rizal Asral, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Hydrocarbon releases might result in serious consequences in various aspects. In addition to the contribution to environmental pollution, repetitive leakages need high repair costs. This study aim is to minimize potential repetitive leakage for other typical 3-phase piping systems. We conducted the risk assessment by adopting Risk Based Inspection (RBI) API 581 to identify risk level, calculating piping lifetime, recommended inspection plan and mitigations. The most relevant root causes can be obtained through quantitative Fault Tree Analysis (FTA). Observation and investigation was taken from eight 3-phase piping systems that experienced repetitive leakages. It has been found that the risk level …

Nitrogen Gas Quenching Pressure Effect On Bs S155 Alloy Steel In Vacuum Furnace, Agus Mulyadi Hasanudin, Eddy Sumarno Siradj

Journal of Materials Exploration and Findings

The production of metal and alloy products requires the use of heat treatment, when during the heat treatment process, quenching is a crucial step. The quenching medium can be anything from water, a salt bath, oil, air and gas. In a vacuum furnace, pressurized gas, most frequently nitrogen (N₂) gas, serves as one of the quenching mediums. One of the drawbacks of the quenching process is the distortion and dimensional change of the parts. This paper aims to investigate the influence of nitrogen gas quenching pressure on the distortion and dimensional change of aerospace actuator gear planet parts …

Characterization Of Interlayer Laser Shock Peening During Fused Filament Fabrication Of Polylactic Acid (Pla), Fabien Denise

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The field of additive manufacturing (AM) has gained a significant amount of popularity due to the increasing need for more sustainable manufacturing techniques and the adaptive development of complex product geometries. The problem is that AM parts routinely exhibit flaws or weaknesses that affect functionality or performance. Over the years, surface treatments have been developed to compensate certain flaws or weaknesses in manufactured products. Combining surface treatments with the modularity of additive manufacturing could lead to more adaptable and creative improvements of product functions in the future. The current work evaluates the feasibility of pursuing a new research axis in …

Constructing Carbon-Encapsulated Nifev-Based Electrocatalysts By Alkoxide-Based Self-Template Method For Oxygen Evolution Reaction, En-Hui Ma, Xu-Po Liu, Tao Shen, De-Li Wang

Journal of Electrochemistry

The development of green and sustainable water-splitting hydrogen production technology is beneficial to reducing the over-reliance on fossil fuels and realizing the strategic goal of "carbon neutral". As one of the half reactions for water splitting, oxygen evolution reaction has suffered the problems of sluggish four-electron transfer process and relatively slow reaction kinetics. Therefore, exploring efficient and stable catalysts for oxygen evolution reaction is of critical importance for water-splitting technology. Metal alkoxides are a series of compounds formed by the coordination function of metal ions with alcohol molecules. Metal alkoxides possess the double advantages of organic materials and inorganic materials, …

Chain Conformation And Exciton Delocalization In A Push-Pull Conjugated Polymer, Yulong Zheng, Rahul Venkatesh, Connor P. Callaway, Campbell Viersen, Kehinde H. Fagbohungbe, Aaron L. Liu, Chad Risko, Elsa Reichmanis, Carlos Silva-AcuñA

UK CARES Faculty Publications

Linear and nonlinear optical line shapes reveal details of excitonic structure in polymer semiconductors. We implement absorption, photoluminescence, and transient absorption spectroscopies in DPP-DTT, an electron push−pull copolymer, to explore the relationship between their spectral line shapes and chain conformation, deduced from resonance Raman spectroscopy and from ab initio calculations. The viscosity of precursor polymer solutions before film casting displays a transition that suggests gel formation above a critical concentration. Upon crossing this viscosity deflection concentration, the line shape analysis of the absorption spectra within a photophysical aggregate model reveals a gradual increase in interchain excitonic coupling. We also observe …

Surface Modifications Of Lini0.96Co0.02Mn0.02O2 With Tungsten Oxide And Phosphotungstic Acid, Gang Zhao, Zheng-Liang Gong, Yi-Xiao Li, Yong Yang

Journal of Electrochemistry

With the rapid development of electric vehicles, enormous demands are made for higher energy density, better cycling performance and lower cost of lithium-ion batteries (LIBs). As an important high capacity cathode material for LIBs, the high nickel layered oxide material LiNi_0.8Co_0.1Mn_0.1O₂(NCM811) can reach an energy density of 760 Wh·kg^-1. The ultra-high nickel ternary positive electrode material (LiNi_1-x-yCo_xMn_yO₂, x ≥ 0.90) has a specific capacity of more than 210 mAh·g^-1, and can realize higher energy density. Besides, an ultra-high nickel material …

Preparation And Electrocatalytic Performance Of Feni-Cop/Nc Bifunctional Catalyst, Si-Miao Liu, Jing-Jiao Zhou, Shi-Jun Ji, Zhong-Sheng Wen

Journal of Electrochemistry

Rechargeable zinc-air batteries have gradually attracted much attention worldwide due to their high capacity, high energy density and low price. Oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) correspond to the charging and discharging processes in rechargeable zinc-air battery, respectively. At present, commercial Pt/C and IrO₂ catalysts hinder the large-scale application of zinc-air batteries due to low reserves, high prices and poor stability. Therefore, exploring high performance, low cost and high stability with dual functional catalysts is important for the development of rechargeable zinc-Air batteries. The metal-organic frameworks (MOFs) have high specific surface area, structural stability, good catalytic …

Corrosion Case Study On Pipeline, Kangze Ren

Corrosion Research

The Kashagan pipeline leaks were likely caused by sulfur stress corrosion cracking, a combined corrosion mechanism developed by the presence of high pressure, the high level of hydrogen sulfide(the main "ingredient" of sour gas), and poor metallurgical choice. Improper welding and poor metallurgical examination were blamed for causing the leaking issue. The purpose of the current review is to raise the alarm about the inappropriate corrosion management of Kashagan oil production and its societal and environmental consequences.

Hydrophobicity Optimization Of Cathode Catalyst Layer For Proton Exchange Membrane Fuel Cell, Hao-Jie Chen, Mei-Hua Tang, Sheng-Li Chen

Journal of Electrochemistry

Hydrophobicity of the cathode catalyst layers (CCLs) crucially determines the performance of proton exchange membrane fuel cells (PEMFCs) by affecting the transports of oxygen and liquid water. In this regard, polytetrafluoroethylene (PTFE) is usually used as a hydrophobic additive to facilitate the oxygen and water transports in CCLs. So far, there remains lacking systematic effort to optimize the addition methods of PTFE in CCLs and the mechanisms behind. In this work, the effects of the approaches for PTFE addition and the distribution of PTFE on the mass transport of oxygen and the proton conduction in CCLs were studied by using …

Synthesis And Evaluation Of Organic Additives For Copper Electroplating Of Interconnects, Yue-Hui Zhai, Yi-Xiao Peng, Yan Hong, Yuan-Ming Chen, Guo-Yun Zhou, Wei He, Peng-Ju Wang, Xian-Ming Chen, Chong Wang

Journal of Electrochemistry

Copper interconnects are essential to the functionality, performance, power efficiency, reliability, and fabrication yield of electronic devices. They are widely found in chips, packaging substrates and printed circuit boards, and are often produced by copper electroplating in an acidic aqueous solution. Organic additives play a decisive role in regulating copper deposition to fill microgrooves, and micro-vias to form fine lines and interlayer interconnects. Generally, an additive package consists of three components (brightener, suppressor, and leveler), which have a synergistic effect of super-filling on electroplating copper when the concentration ratio is appropriate. Many works of literature have discussed the mechanism of …

Hydrodynamic Voltammetry Of Fe2+/3+ In Aqueous Deep Eutectic Solvents Towards Redox Flow Batteries, Desiree Mae Prado, Xiaochen Shen, Robert Savinell, Clemens Burda

Faculty Scholarship

Deep eutectic solvents (DESs) have recently attracted much attention as potential green electrolyte solvents for redox flow batteries. DESs are considered not only as environmentally sustainable but also economically attractive electrolytes because they can be resourced from biological feedstock (alcohols, urea, choline) and are earth-abundant and of low toxicity. Despite these advantages, DESs still have limitations in important aspects such as reactant and ion transport, which is inhibited due to hydrogen-bonding-induced viscosity. Thus, improving the transport properties of redox species in DESs is essential. In addition, we explore the quantitative addition of water to ethaline (a 1:2 choline chloride: ethylene …

Recent Progress Of Bifunctional Electrocatalysts For Oxygen Electrodes In Unitized Regenerative Fuel Cells, Tian-Long Zheng, Ming-Yu Ou, Song Xu, Xin-Biao Mao, Shi-Yi Wang, Qing-Gang He

Journal of Electrochemistry

Unitized regenerative fuel cells (URFCs), which oxidize hydrogen to water to generate electrical power under thefuel cells (FCs) mode and electrolyze water to hydrogen under the water electrolysis (WE) mode for recycling, areknown as clean and sustainable energy conversion devices. In contrast to the hydrogen oxidation reaction (HOR) andhydrogen evolution reaction (HER) on the hydrogen electrode side, the sluggish kinetics of oxygen reduction reaction(ORR) and oxygen evolution reaction (OER) on the oxygen electrode side requires highly efficient bifunctional oxygencatalysts. Conventional precious metal oxygen catalysts combine Pt and IrO₂ with excellent ORR and OER activities toachieve bifunctional electrocatalysis performance, but …

Band Alignments Of Metal/Oxides-Water Interfaces Using Ab Initio Molecular Dynamics, Yong-Bin Zhuang, Jun Cheng

Journal of Electrochemistry

Band alignments of electrode-water interfaces are of crucial importance for understanding electrochemical interfaces. In the scenario of electrocatalysis, applied potentials are equivalent to the Fermi levels of metals in the electrochemical cells; in the scenario of photo(electro)catalysis, semiconducting oxides under illumination have chemical reactivities toward redox reactions if the redox potentials of the reactions straddle the conduction band minimums (CBMs) or valence band maximums (VBMs) of the oxides. Computational band alignments allow us to obtain the Fermi level of metals, as well as the CBM and VBM of semiconducting oxides with respect to reference electrodes. In this tutorial, we describe …

From Waste To Energy: The Electrochemical Reduction Of Co2 Using Recycled Nanostructured Catalysts, Ibrahim Badawy

Theses and Dissertations

The reduction of carbon dioxide (CO₂RR) using electrochemistry is a promising solution for the burgeoning global energy crisis. The overall vision of its implementation relies on renewable energy sources to power the reaction creating carbon neutral products and effectively closing the carbon cycle. Research in this field has come a long way since its inception in the mid-1900s. However, there remain significant hurdles and important considerations to overcome in order to reach full commercialization. Most electrocatalysts tested for CO₂RR have been designed solely for maximum performance while ignoring the environmental consequences if such a material were …

The Effect Of Heat Treatment And Chemical Treatment On Natural Fibre To The Durability Of Wood Plastic Composites – A Review, Nuratiqah Asyiqin Mohd Nasharudin, Nur Fatihah Sulaiman, Nurul Aziemah Mohammad, Wan Nor Raihan Wan Jaafar, Falah Abu Dr., Siti Norasmah Surip

Journal of Materials Exploration and Findings

The application of WPC is not only limited to indoor applications but has been extended to exterior applications where properties of WPC could compromise during service life. WPC was derived from wood fiber of various sizes to reinforce polymers. Wood fiber has the advantage of a cheaper price, being abundantly available, and ease of processing, however, the critical factor is its hydrophilic nature, where moisture absorption is likely to occur. Thus, treatments for reducing the hydrophilicity of wood fibers are applied. By treatment of wood fiber, the surface impurities were removed, leaving the roughened surface of fibers, thus providing a …