Chemical Engineering Commons^™

Recent Research Progress For Non-Pt-Based Oxygen Reduction Reaction Electrocatalysts In Fuel Cell, Ping Song, Ming-Bo Ruan, Jing Liu, Guang-Jun Ran, Wei-Lin Xu

Journal of Electrochemistry

The expensive Pt-based catalyst suffers from its susceptibility to time-dependent drift, methanol crossover, and carbon monoxide (CO) deactivation, which will block the large-scale commercial application of fuel cells. It is, therefore, necessary to develop efficient, low-cost, highly stable non-precious metal oxygen reduction reaction (ORR) catalysts with high catalytic performance. Here, we will pay attention to the research progress of non-precious metal and heteroatom-doped (N, B, P, S, F) metal-free ORR catalysts. Importantly, we mainly focus on the work developed by Xu’s group with the Fe-based non-precious metal and F/NF-doped metal-free ORR catalysts. The purpose of these works is to improve …

Preparation And Properties Of Binary Oxides CoXCr1-XO3/2 Electrocatalysts For Oxygen Evolution Reaction, Tai-Lai Yang, Wen-Yan Dong, Hui-Min Yang, Li Zhang, Zhen-Hai Liang

Journal of Electrochemistry

Binary metal mixed oxides of Co and Cr with nominal compositional formulas, Co_xCr_1-xO_3/2 (x=0, 0.2, 0.4, 0.6, 0.8 and 1.0), were obtained by thermal decomposition method. The morphologies, crystal forms and valence states of the catalyst powders were analyzed by SEM, XRD and XPS, respectively. And the electrochemical properties, overpotentials and stabilities of Co_xCr_1-xO_3/2 electrodes for oxygen evolution reaction (OER) in an alkaline solution were evaluated by linear sweep voltammetry (LSV), staircase voltammetry and chronoamperometry, respectively. The results indicated that the mixtures of Co₃O₄ and eskolaite-Cr_{2 …}

Synthesis And Electrochemical Properties Of Cnts/V2O5 Hollow Microspheres, Liang Hao, Lai-Fa Shen, Jie Wang, Jia-Jia Zhu, Xiao-Chen Zhao, Xiao-Gang Zhang

Journal of Electrochemistry

The carbon nanotubes/vanadium oxides (CNTs/V₂O₅) hollow microspheres (VOC) were prepared via solvothermal process. The effects of the ratio for CNTs to V₂O₅ on the morphologies, structures and electrochemical performances were systemically investigated. The results indicate that CNTs dramatically enhanced the rate performances of VOC composite electrodes. When the ratio of CNTs is 7.1%, the VOC composite electrode exhibited the best electrochemical performance, which delivered a specific capacitance of 346 F·g^-1 at 0.5 A·g^-1 and maintained 75% at 8 A·g^-1 in 5 mol L^-1 LiNO₃. A hybrid capacitor …

Porous Co3O4 Hollow Nanospheres Cathode Catalyst For High-Capacity And Long-Cycle Li-Air Batteries, Tong Liu, Na Li, Qing-Chao Liu, Xin-Bo Zhang

Journal of Electrochemistry

In this paper, a high specific surface area of porous Co3O4 hollow nanospheres was successfully synthesized via hydrothermal carbonization at 140 °C, followed by calcination using cobalt nitrate hexahydrate (Co(NO3)2·6H2O), hexamethylenetetramine (HMT), sucrose, and sodium citrate (Na3C6H5O7). The porous Co3O4 hollow nanospheres consisted of nanoparticles with high specific surface area of mesoporous structure, and could provide active reaction sites for OER and ORR. When used as lithium-air battery cathode catalyst, the Co3O4/Super P (SP) electrode exhibited excellent cycle performance, resulting in high capacity and long life of lithium-air batteries.

Syntheses And Electrochemical Performances Of Li4Ti5O12 Anode Materials For Lithium Ion Battery, Yong-Long Zhang, Xue-Bu Hu, Yao-Qiong Wang, Dong-Hai Huang

Journal of Electrochemistry

Series of spinel lithium titanate (Li₄Ti₅O₁₂) materials were synthesized by one-step solid-state reaction using lithium acetate and TiO₂ as raw materials under different temperatures (750/800/850 °C) and atmospheres (N₂/air). The as-prepared Li₄Ti₅O₁₂ materials were investigated by thermogravimetric analysis, X-ray diffraction, scanning electron microscopy, cyclic voltammotry and charge-discharge test to analyze their crystal structures, microstructures and electrochemical performances. The results show that the Li₄Ti₅O₁₂（L-800N）material obtained at 800 °C under nitrogen atmosphere exhibited better electrochemical performance and smaller particle size. The initial …

An Enzymatic Ethanol/O2 Biofuel Cell Powered By Commercial Vodka Fuel, Yi-Ming Yan, Lan-Qun Mao

Journal of Electrochemistry

This study demonstrates the performance of a new type alcohol/O₂ biofuel cell assembled by using alcohol dehydrogenase (ADH) and bilirubin oxidase (BOD) as the biocatalysts of the bioanode and the biocathode for the bioelectrocatalytic oxidation of alcohol and reduction of oxygen, respectively. To construct the bioanode and the biocathode, single-walled carbon nanotubes (SWCNTs) were used. In the bioanode, SWCNTs were used as the supporting materials for both methylene green (MG) which was used as the electrocatalyst for the oxidation of NADH and ADH. The as-constructed MG/ADH/SWCNTs-based bioanode exhibits a good activity toward the bioelectrocatalytic oxidation of ethanol. In the …

Preparation And Properties Of Titanium Based Metal Oxide Electrodes For Ammonia Nitrogen Wastewater Treatment, Xue Li, Meng Xue, Ling Huang, Jun-Tao Li, Shi-Gang Sun

Journal of Electrochemistry

In this paper, four types of titanium based metal oxides electrodes were prepared by thermal decomposition method: Ti/SnO₂+Sb₂O₃, Ti/SnO₂+Sb₂O₃/SnO₂+IrO₂, Ti/SnO₂+Sb₂O₃/SnO₂+RuO₂, Ti/SnO₂+Sb₂O₃/SnO₂+CeO₂. The XRD results show that CeO₂ in Ti/SnO₂+Sb₂O₃/SnO₂+CeO₂ displayed a good crystal structure, and there was no significant oxygen evolution reaction occurred after electrolytic oxidation. Compared with the other three electrodes, the Ce-doped …

Naio4 Oxidation Of Mussel Adhesive Protein Film And Its Corrosion Protection For Mg-1.0ca Alloy, Rui-Qing Hou, Ping-Li Jiang, Shi-Gang Dong, Chang-Jian Lin

Journal of Electrochemistry

The effect of oxidation of mussel adhesive protein (Mefp-1) film on the corrosive resistance for Mg-1.0Ca alloy was investigated by scanning electron microscopy (SEM), atom force microscopy (AFM), electron probe microanalysis (EPMA), Infrared reflection absorption spectroscopy (IRAS) and electrochemical methods. The results showed that the NaIO₄ induced oxidation of the pre-formed Mefp-1 film with porous morphology involved structural change of the DOPA group in the protein and resulted in a more uniform film with net-like morphology. The protein film without oxidation had an increasing resistance for the corrosion of Mg-1.0Ca alloy up to 7 days exposure. After oxidation, Epit …

Electrochemical Monitoring Of Cell Wall-Regulated Transient Extracellular Oxidative Burst From Single Plant Cells, Jun-Tao Liu, Yan-Ling Liu, Zhi Cheng, Shi-Jing Chen, Wei-Hua Huang

Journal of Electrochemistry

Oxidative burst by rapid, transient generation of reactive oxygen species (ROS) is a fundamental process for plant disease defense and signal transduction. ROS can be protective or toxic depending on their concentrations, and critical balance between ROS production and scavenging is regulated by complex and perfect mechanisms in plant cells. However, the process of rapid and transient ROS burst from plant cells and their regulatory mechanisms are far from being completely understood, owing to the methodological obstacles in real-time monitoring such a fast process. In this work, we showed the application of microelectrode electrochemistry with high spatiotemporal resolution to monitor …

Transition States And Modeling For Co9s8/Mos2 Catalysis, Gabriel Angel Gonzalez

Open Access Theses & Dissertations

Transition state computational studies of the sulfur removal from dibenzothiophene (DBT) molecule have herein been performed considering the Co9S8/MoS2 interface existing on unsupported Co/MoS2 catalysts. The linear synchronous transit (LST) and quadratic synchronous transit (QST) methods integrated in a density functional theory (DFT) program such as Dmol3 were used for the calculations of energy barriers of the transition states. Three different configurations present on the Co9S8/MoS2 interface have been envisaged as possible catalytic sites: sulfur-sulfur (S, S) sites, and molybdenum-sulfur (Mo, S) and molybdenum-molybdenum (Mo, Mo) edge sites. This study revealed that the (Mo, Mo) edge site is the most …

Transition Metal Carbide (Tmc) Novel Materials For Novel Catalytic Applications, Svetlana Lagoykina

Open Access Theses & Dissertations

Transition metal carbides (TMC) constitute a diverse class of materials and traditionally have many technological applications. TMC became a subject of extensive research since 1973, when their platinum -like properties were discovered. They demonstrated high catalytical activity and selectivity in a variety of chemical reaction and have potential for some novel catalytic application.

This research is an effort to design new high effective, selective and stable bimetal or alkali promoted TMC catalyst. After extensive theoretical research a wide range of TMC, including bimetal and alkali promoted carbides, were synthesized by different methods. All solids were characterized by XRD and microscopy. …

Platinum Hollow Nanospheres With Different Sizes: Controllable Synthesis And Electrocatalytic Oxidation Toward Methanol, Xuan Lin, Mei-Qin Cheng, Zhong-Jin Shang, Ting Xiong, Xian-Tu Zhang, Wei Tian, Jian-Yun Lin, Qi-Ling Zhong, Bin Ren

Journal of Electrochemistry

The selenium (Se) templates and hollow platinum (Pthollow) nanospheres with different sizes were controllably synthesized by adjusting the concentration of sodium dodecyl sulphonate (SDSN) (CSDSN, μmol·L-1) which was used as a surfactant. Accordingly, the Pthollow nanospheres modified glassy carbon (GC) electrode (Pthollow/GC) was prepared. The morphology and composition of Pthollow nanospheres were characterized by scanning electron microscopy (SEM), transmission electron microscope (TEM), energy dispersive X-ray spectroscopy (EDX), high resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED) and X-ray diffraction (XRD) techniques. The electrocatalytic activities of Pthollow/GC and electrodeposited Pt nanoparticles modified glassy carbon electrode (Ptnano/GC) toward methanol oxidation …

Comparison In Factors Affecting Electrochemical Properties Of Thermal-Reduced Graphene Oxide For Supercapacitors, Peng Xiao, Da-Hui Wang, Jun-Wei Lang

Journal of Electrochemistry

In this paper, thermal-reduced graphene oxide (T-RGO) materials are synthesized by modified Hummer’s method, followed by thermal reduction under argon atmosphere at different temperatures. Electrochemical investigations show that, for T-RGO electrodes, good electrical conductivity is necessary and the surface functional groups play more significant role than the specific surface area in determining the electrochemical capacitance. The T-RGO obtained at 900 °C (T-RGO900) with a relatively high Brunauer-Emmett-Teller (BET) surface area (314 m²·g^-1) and a high electrical conductivity (2421 S·m^-1) shows a low specific capacitance of 56 F·g^-1. In comparison, the T-RGO obtained …

Synthesis Of Namnpo4 By Spraying Drying-High Temperature Sintering And Its Electrochemical Performance, Xiao-Chen Lin, Xiao-Biao Wu, Xu Hou, Yong Yang

Journal of Electrochemistry

As a cathode material for sodium ion batteries, NaMnPO₄/C nanocomposite is successfully synthesized by the combination of spraying drying and high temperature sintering methods. The crystal structure of the as-synthesized phosphate material is confirmed as the natrophilite NaMnPO₄, which possesses orthorhombic symmetry and Pmnb space group. It is shown that the precursors are hollow spherical particles and the obtained product consists of micro-scaled secondary particles, which are composed of NaMnPO₄ nanocrystallites (tens of nanometres) and amorphous carbon networks. The ionic and electronic conductivities of NaMnPO₄ are both effectively enhanced with the help of this …

One-Step Synthesis Of Pani/Nihcf Hybrid Film Using Unipolar Pulse Electrodeposition And Its Electrocatalytic Reduction Performance For H2O2 Detection, Sen-Liang Liao, Xiu-Min Li, Xiao-Gang Hao, Yan-Hong Wang, Chun-Feng Xue, Yong-Hong Wang

Journal of Electrochemistry

Organic–inorganic hybrid films composed of polyaniline/nickel hexacyanoferrate (PANI/NiHCF) were fabricated on platinum substrates using unipolar pulse one-step electrodeposition. The deposition mechanism of hybrid film was proposed: Due to high potential of unipolar pulse electrodeposition, which avoided the reduction of Fe(CN)₆^3-, the films with high electrocatalytic property and “insoluble” form of NiHCF were achieved. The morphology and composition of PANI/NiHCF hybrid film were characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and Fourier transform infrared spectroscopy (FT-IR). The effect of pulse potential on the electrochemical performance of hybrid film was investigated in detail. Results showed that …

Direct Electrochemistry And Glucose Biosensing Of Glucose Oxidase-Gold Nanoparticles Composite Synthesized By Enzyme Method, Fang He, Xiao-Li Qin, Ying-Chun Fu, Chao Chen, Qing-Ji Xie, Shou-Zhuo Yao

Journal of Electrochemistry

Glucose oxidase (GOx)-gold nanoparticles (AuNPs) composite was synthesized by the one-pot enzyme reaction in the mixture solution of NaAuCl₄, GOx and glucose, and a Nafion/GOx-AuNPs/glassy carbon electrode was fabricated by the cast-coating method to examine the direct electrochemistry of GOx and the biosensing performance on this electrode. Such a GOx-AuNPs composite showed good direct-electrochemistry activity and bioactivity of GOx, probably because the enzyme-mediated AuNPs are close to the redox active centers of GOx. This enzyme electrode exhibited a linear amperometric response to glucose concentration (0.54 mmol·L^-1) at -0.4 V (vs. SCE), and a detection limit of …

Microanalysis Of Polymer Chain Diffusion In Heat Seals, Russell Cooper

All Theses

Heat sealing is an integral method for the closure and protection of packaging. Previous work has shown that seal strength is developed by the interdiffusion of polymer chains within heat seals. Heat seals were made between two dissimilar materials. Poly(ethylene-co-acrylic acid) (EAA) was heat sealed to ionomer. Diffusion within the EAA-ionomer heat seals was estimated. The diffusion estimates were then related to resulting seal strength in the EAA-ionomer sealant system. Heated tooling sealing was utilized to make heat seals at 40 psi (275.79 kPa), 0.5 seconds, and a range of temperatures between 180˚F (82.22˚C) and 300˚F (148.89˚C). Scanning electron microscopy …

Printing Functional Electronic Circuits And Components, Ahmed Tausif Aijazi

Dissertations

The purpose of this study was to investigate the challenges in printing reliable multilayer flexible circuits, devices and components. Gravure was used as the primary printing process for this work, but due to some limitations of gravure, other printing methods were also investigated. At first a systematic study was done to determine the optimum parameters for the gravure printing of sub 50 micron lines. Commercially available silver nanoparticle inks were printed on a lab scale gravure printer, Accupress®. The highest resolution line that was electrically conductive was 36μm wide. The 9μm, 18μm and 27μm lines were printed but were not …

Influence Of Pt:Ru Ratio In Nanotubes Array Structures On The Electrocatalytic Activity Of Methanol Oxidation, Jin-Hua Yuan, Feng-Bin Wang, Xing-Hua Xia

Journal of Electrochemistry

Bimetallic PtRu nanotubes array electrodes (NTAEs) with varied Pt to Ru atomic ratios have been prepared by electrochemical codeposition in 3-aminopropyltri-methoxysilane modified porous anodic alumina (PAA) membranes. The structure and morphology of the catalysts were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. Electrochemical results showed that the NTAEs with varied atomic ratios could be achieved by controlling the precursor concentration for deposition. The prepared nanoarrays composed of Pt or PtRu alloy promoted the mass-normalized activity toward the sluggish electrooxidation reaction of methanol due to the increased catalytic activity and real surface area, as well as the …

Electrochemistry Of Glucose Oxidase Modified On Porin-Phospholipid Biomimic Membrane, Kun-Qi Wang, Zuo-Ming Zhang, Wei Xing, Chang-Peng Liu, Xing Zhou

Journal of Electrochemistry

Biomimic membrane with nano-channels, which is made up of porin MspA and 1,2-Dimyristoyl-sn-glycero-3-phosphocholine (DMPC) is constructed on glassy carbon substrate, and glucose oxidase (GOD) is modified on it. The direct electrochemical reaction and electrocatalytic behavior to oxygen and glucose of GOD on the GOD/MspA-DMPC/GC electreode are expounded by the cyclic voltammetric method. The study shows that GOD immobilized on porin MspA and DMPC biomimic membrane displays direct and surface-controlled electrochemical reaction nearby formal potential (E0′) of the flavoprotein active centre (FAD/FADH), and the electrochemical reaction contains two electrons and two protons exchange in 0.1 mmol·L^-1 phosphate buffer solution (PBS) …

Effect Of Imidazole Ionic Liquids On The Electro-Oxidation Of P-Methoxy Toluene, Qiong Chen, Ying-Hong Zhu, Ying Zhu, Yan-Fang Li, Chun-An Ma

Journal of Electrochemistry

The interactions between four Imidazole ionic liquids (EMIMBF₄, BMIMBF₄, BMIMHSO₄, BMIMAc) and p-methoxy toluene were investigated by ultraviolet spectroscopy. The red shifts of absorption peak were obviously observed, and the fine structures of the spectroscopy were disappeared on the long wave district. p-MT producing stable excited state was benefit from the interaction with solvent molecules. The electro-oxidation behavious of p-MT were studied in the four ILs on platinum electrode by cyclic voltammetry (CV) and chronoamperometry (CP), and the diffusion coefficients (D) and activation energies (ED) were calculated. The results indicated that the electro-oxidation process …

Electro-Catalytic Properties Of Β-Pbo2/Sb-Sno2/Ti Electrode On Phenol Oxidation, Peng Li, Yue-Min Zhao, Li-Zhang Wang, Yan-Le Zhang, Zhao-Qing Lu

Journal of Electrochemistry

The combination technology of brush pyrolysis and electroplating was employed in the preparation of β-PbO₂/Sb-SnO₂/Ti electrode. X-ray Diffraction (XRD) and Scanning Electron Microscope (SEM) results showed that the Sb-SnO₂ as an interlayer would restrain the formation of lead fluoride and the crystallization degree on the electrode surface could be as high as 100%. The grain size was calculated by Scherrer formula to be 25.2 nm and the agglomeration of lead dioxide was effectively eliminated. The potential span of diffusion control phase, oxygen evolution potential, Tafel slope for the β-PbO₂/Sb-SnO₂/Ti electrode during …

Boosting Electrocatalytic Activity Of Nitrogen-Doped Graphene/Carbon Nanotube Composite For Oxygen Reduction Reaction, Yu Zhang, Jin-Song Hu, Wen-Jie Jiang, Lin Guo, Zi-Dong Wei, Li-Jun Wan

Journal of Electrochemistry

Developing low-cost catalysts with high electrocatalytic activity for oxygen reduction reaction (ORR) has recently attracted much attention because the sluggish ORR currently limits the performance and commercialization of fuel cells and metal-air batteries as well. Nitrogen doped carbon materials have been considered as a promising candidate for the replacement of high-cost and scarce Pt-based catalysts although their electrocatalytic activity still needs to be much improved. In this work, an improved nitrogen-doped graphene/carbon nanotubes composite (N-rGO/CNT) was developed as an efficient ORR electrocatalyst. It was found that the ORR activity of N-rGO/CNT composite could be significantly enhanced by introducing iron in …

Recent Progress In Heteroatoms Doped Carbon Materials As A Catalyst For Oxygen Reduction Reaction, Wei Ding, Xue Zhang, Li Li, Zi-Dong Wei

Journal of Electrochemistry

Developing catalytic materials for oxygen reduction reactions (ORR) with high performance and low cost has been one of the major challenges for large-scale applications of fuel cells. In this review, we summarize the recent progress in the heteroatoms doped carbon materials as a catalyst for the catalysis of ORR, with an emphasis on the universal origin of their catalytic mechanisms. The future prospects of the metal-free catalyst were to find precisely controlled doping methods, to explore the role of heteroatoms in the catalysis, and to generate more active catalysts with suitable nanostructure.

Fabrication Of Pattern Of Graphene Oxide And Au Nanoparticles By Microcontanct Printing Technique, Wen-Hui Pang, Xiao-Jian Xiao, Meng-Wei Ye, Kai-Chao Deng, Jing Tang

Journal of Electrochemistry

Graphene oxide (GO) was prepared by modified Hummers method. Using the GO solution as "ink", Au nanoparticles (AuNPs) and GO were transferred to the surface of ITO substrate modified with (3-aminopropyl) triethoxysilane (APTES/ITO) in a sequence. The transferred AuNPs and GO could form a uniform and dense composite pattern which was characterized by FE-SEM and AFM. Moreover, using the APTES/ITO substrate surface potential as zero, the sequences of the surface potential were APTES>GO>Au.

Fabrication And Characterization Of The Ni-Scsz Composite Anodes With A Cu-Lscm-Ceo2 Catalyst Layer In The Thin Film Sofc, Yao Lv, Bo Huang, Xi-Zhi Gu, Chun-Yi Hou, Yi-Xing Hu, Xiao-Yin Wang, Xin-Jian Zhu

Journal of Electrochemistry

Solid oxide fuel cell (SOFC) directly operating on hydrocarbon without external reforming has the potential of greatly speeding up the application of SOFCs for transportation. In this paper, a three-layer structure anode was fabricated by tape casting and screen printing method. The addition of Cu-LSCM-CeO₂ to the supported anode surface presented better performance running on H₂ and ethanol. The maximum power densities were 511 and 390 mW?cm^-2, respectively, running on H₂ and ethanol at 750 °C. No significant degradation was observed on the anode. Consequently, the Cu-LSCM-CeO₂ catalyst layer on the surface of the …

Preparation Of Pt/Dna-Mwcnts/Gc Electrode And Its Electrocatalytic Activity Toward H2O2 Reduction, Li-Li Fan, Li-Na Wu, Zhi-Yu Qu, Dan-Feng Liu, Jun-Ming Zhang, Si-Ming Fan, You-Jun Fan

Journal of Electrochemistry

The DNA-multi-walled carbon nanotubes (MWCNTs)/glassy carbon (GC) electrode was prepared by modifying the DNA functionalized MWCNTs composite on a GC electrode. A novel non-enzymatic H₂O₂ sensing electrode was fabricated by electrodepositing Pt nanoparticles on the DNA-MWCNTs/GC electrode. The modified electrodes were characterized by scanning electron microscope (SEM). The response properties of the sensing electrode to H₂O₂ were investigated by cyclic voltammetry and chronoamperometry. The results indicated that the sensing electrode exhibited a good linear relationship between response current and H₂O₂ concentration in the range of 0.04 ~ 18.07 mmol·L^-1 with …

Electrochemical And Spectroscopic Studies Of Ethanol Oxidation On Nano-Cubic Pt Modified By Tin Adatoms, Lu Rao, Bin-Wei Zhang, Yan-Yan Li, Yan-Xia Jiang, Shi-Gang Sun

Journal of Electrochemistry

The nano-cubic Pt modified by tin (Sn) was synthesized and used to investigate the role of this adatom played in the ethanol oxidation. The onset potential of ethanol oxidation was significantly shifted negatively which can be forward about 300 mV when the coverage of Sn (θSn)was 0.9. The electrtochemical in situ FTIR result demonstrated that the amount of CO₂ increased first, and then decreased with θSn increased, and reached the maximun when θSn was 0.38. Furthermore, the formation of acetic acid could be observed at very low potential (-0.05 V) after modifying Sn adatom, and the amount of acetic …

Electrochemical Catalysis: A Dft Study, Li Li, Zi-Dong Wei

Journal of Electrochemistry

In this review, we focus on achievements in electro-catalysis based on the density function theory study. The relationships among the electrode potential, electronic structure of catalysts and electro-catalytic activity are summarized in three parts: the adsorption and desorption of species, electron transfer, and stability of catalysts. The electrode potential and the electronic structure (d-band center or Fermi (HOMO) energy) of catalysts significantly influence the formation, adsorption and desorption of surface species on electrode. The electro-catalytic activity can be improved by modulating the electrode potential and electronic structure of catalysts.

Recent Progress In The Mechanistic Understanding Of Formic Acid Oxidation On Pt Electrode, Jie Xu, Dao-Chuan Jiang, Dong Mei, Zheng-Da He, Yan-Xia Chen

Journal of Electrochemistry

This article reviews the recent progress in understanding of the mechanisms for formic acid oxidation on Pt electrode. There are two pathways for formic acid oxidation on Pt electrode: (1) Indirect Pathway through which HCOOH is oxidized to CO₂ through CO_ad intermediate. This pathway contributes only 1% of the total current; (2) Direct Pathway where HCOOH is oxidized directly to CO₂. The results from IR Spectroscopy, single-crystal electrochemistry and DFT calculation all support that the bridge-bonded formate is neither the intermediate of direct pathway nor the precursor for CO_ad formation in indirect pathway. Possible mechanism …