Chemical Engineering Commons^™

Developing A 3d In Vitro Model By Microfluidics, Hung-Ta Chien

Dissertations and Theses

In vitro tissue models play an important role in providing a platform that mimics the realistic tissue microenvironment for stimulating and characterizing the cellular behavior. In particular, the hydrogel-based 3D in vitro models allow the cells to grow and interact with their surroundings in all directions, thus better mimicking in vivo than their 2D counterparts. The objective of this thesis is to establish a 3D in vitro model that mimics the anatomical and functional complexity of the realistic cancer microenvironment for conveniently studying the transport coupling in porous tissue structures. We pack uniform-sized PEGDA-GelMA microgels in a microfluidic chip to …

Ion Size Effects On The Properties Of Charge Regulating Electric Double Layers, Divya Jyoti Prakash

Nanoscience and Microsystems ETDs

The behavior of charged interfaces formed in various systems like colloidal solution, fuel cells, battery, electro-deposition, catalysis is governed by the properties of electrical double layer(EDL). Civilized model with charge regulation boundary condition determined by thermodynamic equilibrium at the interface has been used to model electrical double layer and shows that size of the solvent plays a critical role in characterizing the properties of EDL using classical density functional theory.This thesis investigates the impact of ion size in electrolyte solutions on the electrical double layer formed at the interface using a similar model. It is found that ion size greatly …

Experimental Analysis Of R134a, R22, And R404 For An Edibon Taab: Air Conditioning Lab Unit, Kyle T. Heesen

Senior Honors Projects, 2010-2019

This paper presents an experimental analysis of an Ebidon® TAABTM: Air Conditioning Lab unit running on R-134a being compared with R22 and R404 refrigerants, a $24,449 piece of equipment purchased by the JMU ISAT Department. In this paper we will compare the performance of the R-134a refrigerant under a range of working conditions and compare them to how the system would run on R22 or R404. The experimental tests use varying fan speeds and the R-134a data collected is compared to simulated data collected for R22 and R404. Analysis of the collected data and simulated data will be compared on …

Shear Driven Micro-Fluidic Pump For Cardiovascular Applications, Nihad E. Daidzic

Aviation Department Publications

A valveless shear-driven micro-fluidic pump design (SDMFP) for hemodynamic applications is presented in this work. One of the possible medical and biomedical applications is in-vivo hemodynamic (human blood circulation) support/assist. One or more SDMFPs can be inserted/implanted into vascular lumens in a form of a stent/duct in series and/or in parallel (bypass duct) to support blood circulation in-vivo. A comprehensive review of various micro-pump designs up to about mid 2000’s is given in [1,2]. Many of micropump designs considered are not suitable for in-vivo or even in-vitro medical/biomedical applications.

Operating principles, design, and SDMFP features are given in [3]. A …

Evaluation Of A Microfluidic Mixer Utilizing Staggered Herringbone Channels: A Computational Fluid Dynamics Approach, Brian Hama

ETD Archive

Microfluidic platforms offer a variety of advantages including improved heat transfer, low working volumes, ease of scale-up, and strong user control on parameters. However, flow within microfluidic channels occurs at low Reynolds numbers, which makes mixing difficult to accomplish. Adding V-shaped ridges to channel walls, a pattern called the staggered herringbone design (SHB), might alleviate this problem by introducing transverse flow patterns that enable enhanced mixing. However, certain factors affecting the SHB mixer’s performance remain largely unexplored.

In this work, a microfluidic mixer utilizing the SHB geometry was developed and characterized using computational fluid dynamics based simulations and complimentary experiments. …

Surface Enabled Lab-On-A-Chip (Loc) Device For Protein Detection And Separation, Zhichao Wang

Dissertations, Master's Theses and Master's Reports

Sensitive and selective chemical/biological detection/analysis for proteins is essential for applications such as disease diagnosis, species phenotype identification, product quality control, and sample examination. Lab-on-a-chip (LOC) device provides advantages of fast analysis, reduced amount of sample requirements, and low cost, to magnificently facilitate protein detection research. Isoelectric focusing (IEF) is a strong and reliable electrophoretic technique capable of discerning proteins from complex mixtures based on the isoelectric point (pI) differences. It has experienced plenty of fruitful developments during previous decades which has given it the capability of performing with highly robust and reproducible analysis. This progress has made IEF devices …

Plasma Processes And Polymers Third Special Issue On Plasma And Cancer, Mounir Laroussi, Annemie Bogaerts, Nazir Barekzi

Electrical & Computer Engineering Faculty Publications

(First paragraph) This issue of Plasma Processes and Polymers is the third in a series on the applications of low temperature plasma (LTP) against cancer, or “plasma oncology.” The papers in this issue are inspired from the talks given at the third International Workshop on Plasma for Cancer Treatment (IWPCT) which took place on April 11–12, 2016 in Washington, DC, USA. IWPCT is an international workshop that was created in 2014 as a venue to share cutting edge plasma oncology research. The first IWPCT was held in Washington DC, under the co-chairmanship of Prof. Mounir Laroussi (Old Dominion University) and …

Determination Of Aqueous Surfactant Solution Surface Tensions With A Surface Tensiometer, Remelisa Esteves, Birce Dikici Ph.D, Matthew Lehman, Qayyum Mazumder, Nonso Onukwuba

Beyond: Undergraduate Research Journal

Surfactant solutions are applicable to engineering systems for cooling equipment for electronics. Surfactants can be added to water to improve heat transfer. An application of using aqueous surfactant solutions can be through microchannel heat sink. Although it is ideal to redesign these systems to reduce heat, it is a costly method. Surfactant solutions at optimal solution concentration can be able to transfer heat quickly and effectively with minimum expense. The surface tension of surfactant solutions is an important parameter for boiling heat transfer and must be taken into consideration. The purpose of this research is to measure surface tension of …

Determination Of Surfactant Solution Viscosities With A Rotational Viscometer, Remelisa Esteves, Nonso Onukwuba, Birce Dikici Ph.D

Beyond: Undergraduate Research Journal

Aqueous surfactant solutions are used in engineering systems for improving boiling heat transfer. The purpose of this research is to determine the viscosities of surfactant solutions and to investigate the effect of composition on viscosity. The results obtained can possibly be used as reference for further study in the effects of surfactant solution viscosities on nucleate boiling. A rotational viscometer was used to determine the viscosities of three surfactant solutions – SLS, EH-14, and SA-9 – of various compositions at room temperature. It was discovered that the viscosities of SLS, EH-14, and SA-9 had a nearly consistent pattern as their …

Numerical Simulation On The Combustion Characteristic Of Iron Ore Sintering With Flue Gas Recirculation, Gan Wang, Zhi Wen, Guofeng Lou, Ruifeng Dou, Xunliang Liu, Fuyong Su, Sizong Zhang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

The Influence Of Relative Particle Size And Material Interactions On The Flow-Induced Detachment Of Particles From A Microchannel, Morgan Brittany Mayfield

Graduate Theses - Chemical Engineering

Particulate transport in microfluidic channels is difficult due to confined geometries and low flow rates, which promote solids settling. To re-entrain these solids, the detachment behavior of closely-fitting particles from microchannel walls must be understood. Experiments were completed to examine the effects of particle size and material interactions on particle detachment velocity. Studies were conducted for various sizes of glass and poly(methyl methacrylate), PMMA, spheres in glass and poly(dimethyl siloxane), PDMS, microfluidic channels. In addition, an inexpensive method to produce monodisperse PMMA microparticles was developed. To analyze the effect of material interactions, the work of adhesion between the particle and …

Micro Debris Generator, Gordan Bradaric, Ross Byers, Stephen Quanci

Mechanical Engineering

This senior project team at Cal Poly consisting of Stephen Quanci, Gordan Bradaric, and Ross Byers has been commissioned by Erik Brown of Lawrence Livermore National Labs to create a way to reliably and consistently entrain microscopic particles into the hot HTTU flow. These particles will be used to compare the loading rates of new HEPA filters by measuring the pressure drop across the filter. The generated particles would simulate typical conditions in which these HEPA filters are expected to operate, namely fine ash. The particles used for loading the filter are intended to simulate the particulate reaching the LLNL …

Microstructure And Rheology Of Carbon Nanotubes At Air-Water Interfaces, Charles D. Young

Honors Scholar Theses

This work characterizes the material properties of carbon nanotubes at air-water interfaces for potential use in creating stable emulsions. Properties such as length, aspect ratio, contact angle, microstructural ordering, surface pressure, compression and shear elastic moduli, stresses, surface viscosities and non-linearity are explored. Challenges such as deviation from a classical analysis of monolayers are encountered in the form of aggregation, mechanical contributions, and interface relaxation. These factors are taken into account to explain experimental measurements and trends. Ultimately, existing models for more homogeneous systems are resolved with observations to offer insight and areas of promise moving forward.

Particle Image Velocimetry Design & Installation, Zach Ritchie

Mechanical Engineering Undergraduate Honors Theses

This work will mainly focus on the design, construction, and installation of the Particle Image Velocimetry (PIV) system in the Chemical Hazards Research Center wind tunnel. The PIV system utilizes a Class IV (double pulsed) laser, optics to produce a light sheet, timing circuitry, and a high-resolution camera (with buffered output) to measure a system’s velocity (two-dimensional) field by determining the displacement of particles over the time between laser pulses. For maximum mobility and functionality, the PIV system was installed in the center of the tunnel on a moveable cart with the laser and camera mounted to an adjustable support. …

Development Of A Parallel Multiphase Lattice-Boltzmann Solver To Study Stokes Number Effects On Particle Trajectories, Lenan Zhang, Anand Samuel Jebakumar, John Abraham

The Summer Undergraduate Research Fellowship (SURF) Symposium

Particle-laden flows are important owing to their relevance to many engineering devices such as coal combustors, gasifiers and solar thermochemical reactors. In a recent experimental study by Lau and Nathan [1], it was found that particles in a turbulent pipe flow tend to migrate preferentially depending on their Stokes number (St). Particles with a high St (>10) are concentrated near the axis while those with low St (

A Computational Study Of The Potential For Lng Tanker Polystyrene Foam Insulation Failure Under Fire Exposure, Jeffrey David Martinez

Graduate Theses and Dissertations

Liquefied natural gas is shipped across the oceans in large marine carriers. The carriers house the LNG using several different insulation systems. One of these systems involves large aluminum spheres insulated with polystyrene foam. Polystyrene foam is very susceptible to heat degradation. This raised issues as to the extent of possible insulation failure caused by a large ship fire. Experiments were done investigating the nature of polystyrene’s thermal degradation, notably by Brauman, Chen, and Matzinger and Butler. A large scale investigation was also performed by Sandia National Laboratory. However, computational modeling of the degradation was lacking. This work set out …

Novel Separation Methods Using Electrodialysis/Electrodeionization For Product Recovery And Power Generation, Alexander Miguel Lopez-Rosa

Graduate Theses and Dissertations

The use of electrodialytic separations for the purification of products has been a vital technique for the past 50 years in the chemical industry. Originally used for demineralization and desalination, electrodialysis and its counterparts have expanded to assist in product purification, waste and hazard removal, and power generation. This research focused on the development of high purity organic acids purification with low power requirements. Work resulted in the development of a new type of electrodialysis process, specifically the use of ionic liquids as a secondary solvent for the development of dual solvent electrodialysis. Through dual solvent electrodialysis, ions were recovered …

Coalescence-Induced Jumping Of Droplet: Inertia And Viscosity Effects, Samaneh Farokhirad, Jeffrey F. Morris, Taehun Lee

Publications and Research

The problem of coalescence-induced self-propelled jumping of droplet is studied using three-dimensional numerical simulation. The focus is on the effect of inertia and in particular the effect of air density on the behavior of the merged droplet during jumping. A lattice Boltzmann method is used for two identical, static micro-droplets coalescing on a homogeneous substrate with contact angle ranging from 0◦ to 180◦. The results reveal that the effect of air density is significant on detachment of the merged droplet from the substrate at the later stage of the jumping process; the larger the air density, the larger the jumping …

A Study On The Heavy Crude Oil Viscosity Reduction With The Dissolution Of Nitrogen And Carbon Dioxide, Abdurahman Ajumobi

Dissertations and Theses

World's energy challenges would be greatly improved upon if half of the world's heavy oil and extra heavy oil could be made to ow in pipelines. Viscosity reduction of heavy oils is the key to solving this problem. In this study, aside from injecting pure nitrogen and pure carbon dioxide separately into the oil, two different compositions of the mixture of the two gases were also injected. In the first mixture, varied quantities of the two gases were used; 62:5%, 82:2% and 86:4% of the mixture was nitrogen while 37:5%, 17:8% and 13:6% was carbon dioxide at total test pressures …

Fundamental Studies Of Surfactant Templated Metal Oxide Materials Synthesis And Transformation For Adsorption And Energy Applications, Saikat Das

Theses and Dissertations--Chemical and Materials Engineering

This work addresses fundamental aspects of designing templates and curing conditions for the synthesis of mesoporous metal oxide thin films. The first section addresses selection of cationic-carbohydrate surfactant mixtures to synthesize templated silica thin films for selective adsorption of simple carbohydrates based on molecular imprinting. Nuclear magnetic resonance and fluorescence spectroscopy results suggest a novel structure for mixtures of alkyl glucopyranosides or xylopyranosides with cationic (trimethylammonium) surfactants. Despite thermodynamically favorable mixing, the carbohydrate headgroups in the mixed micelle adopt an inverted configuration with their headgroups in the micelle core, and therefore are inaccessible for molecular imprinting. This orientation occurs even …

Measurements And Modeling Of Hydrocarbon Mixture Fluid Properties Under Extreme Temperature And Pressure Conditions, Babatunde A. Bamgbade

Theses and Dissertations

Knowledge of thermodynamic fluid properties, such as density and phase behavior, is important for the design, operation, and safety of several processes including drilling, extraction, transportation, and separation that are required in the petroleum. The knowledge is even more critical at extreme temperature and pressure conditions as the search for more crude oil reserves lead to harsher conditions. Currently, there is dearth of experimental data at these conditions and as such, the predictive capability of the existing modeling tools are unproven. The objective of this research is to develop a fundamental understanding of the impact of molecular architecture on fluid …

Stability Of Aqueous Dispersions Of Titanium Dioxide Against Sedimentation And Aggregation, Guanrong Bai, Xilan Zhu, Elias I. Franses, David S. Corti, Yung-Jih Yang

The Summer Undergraduate Research Fellowship (SURF) Symposium

Particles of titanium dioxide (TiO₂) are widely used as white pigments in paints and inks, due to their brightness and high refractive index. Yet, with TiO₂ having a high density (4.2 g/cm³), particles with typical sizes of 300 nm sediment rapidly even before significant agglomeration can occur. Thus, increasing the stability of TiO2 dispersions against sedimentation as well as aggregation is important. We studied the effect of sodium dodecyl sulfate (SDS), a commonly used dispersant, on the stability of aqueous dispersions of TiO₂ with weight fractions from 0.01 to 40. The sedimentation time of …

Effect Of Sodium Dodecyl Sulfate And Sodium Chloride On The Stability Of Aqueous Dispersions Of Tio2 Particles Against Aggregation And Sedimentation, Xilan Zhu, Guanrong Bai, Elias I. Franses, David S. Corti, Yung-Jih Yang

The Summer Undergraduate Research Fellowship (SURF) Symposium

Dispersions of TiO₂ particles are widely used as the main pigment in white inks for inkjet printers due to its brightness and high opacity. The TiO₂ particles, however, have a high density, and so the possible fast settling of these particles can cause maintenance problems for the printers and lower the printing quality. We studied the effect of sodium dodecyl sulfate (SDS), a commonly used dispersant, on the stability of 1 wt% TiO2 aqueous dispersions, both with and without NaCl, against aggregation and sedimentation. The sedimentation half time (t50), defined as the time need for the particles to …

A Soft Condensed Matter Approach Towards Mathematical Modelling Of Mass Transport And Swelling In Food Grains, Michael Chapwanya, N. Misra

Articles

Soft condensed matter (SCM) physics has recently gained importance for a large class of engineering materials. The treatment of food materials from a soft matter perspective, however, is only at the surface and is gaining importance for understanding the complex phenomena and structure of foods. In this work, we present a theoretical treatment of navy beans from a SCM perspective to describe the hydration kinetics. We solve the transport equations within a porous matrix and employ the Flory–Huggin’s equation for polymer–solvent mixture to balance the osmotic pressure. The swelling of the legume seed is modelled as a moving boundary with …

Effect Of Ionic Liquid Electrolytes In Dsscs With Titanium Dioxide (Tio2) Inverse Opal Structures, Naomi S. Ramesar

Dissertations and Theses

Dye-sensitized solar cells (DSSC) are low-cost alternatives to conventional solar cells that can work well in low-light conditions. Despite considerable study on improving the efficiency of DSSCs, the current liquid electrolyte cell has plateaued at a conversion efficiency of ~ 12%. A major problem with these cells regarding their applicability is the low viscosity and high volatility of the toxic electrolyte, i.e., acetonitrile, which cause leakage and volatilization. We propose that using ionic liquids (ILs), which are more viscous, less volatile, and conductive, may be more suitable electrolytes. However, one unwanted side effect of the higher viscosity of the ILs …

Low Volume Dispensing With High Speed Dispensers, Sunny Agarwal

Graduate Dissertations and Theses

With the high pace of innovation in the semiconductor manufacturing industry, there has been an increasing demand for more energy efficient and environmental friendly products. This research relates to a complex process of fluid dispensing at low volumes on a printed circuit board. Currently, a more refined non-contact dispensing terminology named “Streaming” is widely used to stream out material at low volumes for various applications. The key solution is to frame a dispensing method that lends itself most closely to the requirements of a specific production process.

This study represents a detailed approach of dispensing low volumes of materials in …

Method And Apparatus For Measurement Of Fluid Properties, Feredoon Behroozi

Patents (University of Northern Iowa)

A method and apparatus for determining the contact angle and/or surface tension of a liquid on a solid surface is described. The method involves placing a fluid drop on a solid surface, and gradually increasing its volume by adding more fluid, while continuing to determine the corresponding increase in fluid height, until the drop attains maximum height beyond which additional fluid only increases the drop footprint and not height, and determining the equilibrium height and in turn the contact angle by means of an equation that correlates contact angle with depth below the fluid surface, together with the fluid surface …

Efficient Numerical Scheme Of The Dynamics Of Nonisothermal Thin Film Flow, Moustafa A. Soliman, Khalid I. Alhumaizi

Chemical Engineering

In this work we use Lubrication type method, based on the possibility of the separation of longitudinal and transversal length scales to simplify the analysis of thin film dynamics. We study the dynamics of evaporating thin liquid films on an inclined plane, where the effect of van der Waal forces is significant. The numerical solution of the evolution equation is carried out using the method of orthogonal collocation and is used for the study of the instabilities of evaporating thin film to identify conditions for efficient operation. For symmetric cases where the plane is horizontal, a two spline collocation second …

Dynamics Of A Coating Film Flow On Horizontal Cylinders With Van Der Waals Forces, Moustafa A. Soliman, Khalid I. Alhumaizi

Chemical Engineering

In this work we use the lubrication type method, based on the possibility of the separation of longitudinal and transversal length scales, to simplify the analysis of coating film dynamics. We study the dynamics of coating thin films on horizontal stationary and rotating cylinders in general, and when the effect of van der Waals forces is significant. A computer code based on the method of orthogonal collocation is developed and is used for the study of the instabilities of coating thin film flow on cylinders to identify conditions of stable operation. For stationary cylinders, the equations are symmetric and the …

Characterization And Quantification Of Monomers, Oligomers, And By-Products From Xylan During Biomass Pretreatment, Ching-Shuan Lau

Graduate Theses and Dissertations

Biomass pretreatment generates inhibitory products, which reduce the overall yield of xylose for ethanol production. Understanding of hemicellulose depolymerization into xylose is essential to identify the pretreatment conditions that maximize xylose formation, but minimize the generation of these inhibitory products, such as formic acid and furfural. Thus, the goal of this project is to understand how dilute acid pretreatment parameters affect hemicellulose depolymerization, maximize xylose concentrations, and minimize by-products formation.

To progress towards this goal, rates and mechanisms of hemicellulose release must be determined. Birchwood xylan was used as the starting material to produce xylose oligomers. The hydrolyzed birchwood xylan …