Chemical Engineering Commons^™

Selective Direct Electro-Oxidation Of C-H Bond, Yan-Mei Liao, Qian-Qian Wu, An-Lun Zhang, Ying-Hong Zhu, Chun-An Ma

Journal of Electrochemistry

Carbon-hydrogen (C-H) bond is the most basic chemical bond in organic compounds. The activation and direct conversion of C-H bond are the effective methodology for synthesis of different kinds of organic compounds from alkane compounds. The oxidative activation and functionalization of C-H bonds constitute an important and challenging area of investigation. The electro-oxidative activation of C-H bonds to form new C-O, C-C and C-N bonds has proven to be interesting and important in organic chemistry using the clean electron as the oxidant. The target C-O, C-C and C-N compounds could be selectively achieved by choosing the appropriate electrode, supporting electrolyte …

A Comparison Study Of Two Synthesis Methods For Polymer Of Intrinsic Microporosity 1 (Pim-1), Conor S. Perry

Materials Engineering

Polymers of Intrinsic Microporosity (PIMs) are an emerging polymeric material class for molecular sieving applications. This study focuses on PIM-1, an alternating copolymer of 5,5’,6,6’-tetrahydroxy-3,3’,3,3’-tetramethyl-1,1’-spirobisindane and tetrafluoroterephthalonitrile synthesized via nucleophilic aromatic substitution. PIM-1 been widely studied as a gas separating material and filtering membrane, but in this case, it is studied as a battery separator material. PIM-1’s microporous (pore diameters less than 2 nm) structure allows smaller favorable ions to transport while preventing larger ions and compounds from transporting. Two synthesis methods, round bottom flask synthesis and ball mill synthesis, of PIM-1 are compared to see any improved characteristics. The …

Synthesis And Characterization Of Molybdenum Sulfide And For Hydrogen Evolution Reaction And Supercapacitor Applications, Zhuo Wang

Electronic Theses & Dissertations

To meet the constantly rising requirement of energy other than traditional fossil fuel and environment protection, it is a perfect time to development low cost, and efficient materials for clean energy production. Hydrogen generation by water splitting is one of the cleanest ways to produce cheaper energy. Hydrogen evolution reaction (HER) is one of the key steps in water splitting process. Ideally, the thermodynamic potential for HER should be at 0 V (vs. SHE). However, without an efficient catalyst, this reaction occurred at higher potential, called overpotential. A good HER catalyst is needed to lower the overpotential and hence to …

Polyisobutylene Telechelic Prepolymers By In Situ End-Quenching And Post-Polymerization Modifications, Bin Yang

Dissertations

This volume focuses on the development of telechelic polyisobutylene (PIB) prepolymers by combining end-capping of living carbocationic polymerization of isobutylene (IB) with suitable reactants and post-polymerization modifications. Alkylation kinetics of PIB tert-chloride with alkoxybenzenes using either TiCl₄ or AlCl₃ were investigated. Quantitative para-position end-capped products were only achieved if the alkoxybenzene/AlCl₃ molar ratio was greater than unity; while no such molar ratio is required for TiCl₄, but the alkylation rate was slower than AlCl₃ under the same conditions. Photopolymerization kinetics analysis of PIB triphenol tri(meth)acrylates with low and high M_ns, …

Recent Progress In Template-Assisted Synthesis Of Nitrogen-Doped Porous Carbons For Oxygen Electroreduction, Wenhan Niu, Ligui Li, Shaowei Chen

Journal of Electrochemistry

Nitrogen (N)-doped porous carbons are potential alternatives to precious metal catalysts for oxygen reduction reaction (ORR) at the cathodes of proton exchange membrane fuel cells and metal-air batteries. Template-assisted synthesis has been used extensively as a robust and versatile method in the preparation of such carbon catalysts, where the ORR activity has been found to be dependent on various structural parameters, such as the concentrations and molecular configurations of the dopants, and the porosity, surface accessibility and electrical conductivity of the carbon materials. In this review, we summarize recent progress in this area of research focusing on the design, preparation …

Comparison Of Oxygen Reduction Reaction Activity Of Pt-Alloy Nanocubes, Yongan Tang, Lin Dai, Shouzhong Zou

Journal of Electrochemistry

Alloying Pt with the first row non-noble transition metals has been demonstrated to increase the catalytic activity toward oxygen reduction reaction (ORR), which is the cathode reaction of the proton exchange membrane fuel cells (PEMFCs) and metal-air batteries. However, how much the ORR activity improvement comes from the alloying elements remains controversial. In this paper, the nanocubes of PtMn, PtFe, PtCo, and PtNi with the similar size and composition were prepared and their ORR activities were explored, in order to investigate the effects of alloying elements on the catalytic activity. The use of cubic shape particles minimizes the contribution to …

Designing Pt-Skin Of Pt-Based Bimetallic Electrocatalysts For Oxygen Reduction Reaction, Binwei Zhang, Yunxiao Wang, Yanfei Xu, Huakun Liu, Shixue Dou

Journal of Electrochemistry

In the past decade, great advancement has been made in the development of nanocatalysts for energy conversion and storage. Pt-skin of Pt-based bimetallic has shown a great potential in the tuning the electronic structures of electrocatalytically active materials toward oxygen reduction reaction. Here, we offer a brief overview of the recent research on the design and preparation of catalysts. Our focus is paid on the systematic studies of preparation and performance of Pt-skin catalysts towards oxygen reduction reaction.

Comparative Studies Of Fe, Ni, Co And Their Bimetallic Nanoparticles For Electrochemical Water Oxidation, Maduraiveeran Govindhan, Brennan Mao, Aicheng Chen

Journal of Electrochemistry

The design of efficient, durable, and earth-abundant electrocatalysts via environmentally compatible strategies for the oxygen evolution reaction (OER) is a vital for energy conversion processes. Herein we report a facile approach for the fabrication of low-cost and earth abundant metal catalysts, including iron (Fe), nickel (Ni), cobalt (Co), CoNi, and CoFe nanoparticles (NPs) on titanium (Ti) substrates through a one-step electrochemical deposition. Field-emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) spectrocopy, X-ray photoelectron spectroscopy (XPS), and electrochemical techniques were employed to characterize these nanoparticles. Our electrochemical results revealed that among the five synthesized nanomaterials, the …

Impact Of Nafion Loading And Anion Adsorption On The Synthesis Of Pt Monolayer Core-Shell Catalysts, Lijun Yang, Dustin Banham, Elod Gyenge, Siyu Ye

Journal of Electrochemistry

Carbon supported palladium (Pd) nanoparticles were used as a model core material for the synthesis of platinum (Pt) monolayer core-shell catalysts using rotating disk electrode method and a copper (Cu) under potential deposition technique. The impact of Nafion on the synthesis process was revealed by electrochemical testing with various Nafion contents. The existence of Nafion influenced the Cu under potential deposition, galvanic replacement and eventually the oxygen reduction reaction activity of the core-shell catalyst. However, as long as the Nafion content was less than 5 wt% in the test film, adding Nafion could help to bind catalyst onto the surface …

Electrodeposition Of Ruo2 Layers On Tio2 Nanotube Array Toward Co2 Electroreduction, Bei Jiang, Lina Zhang, Xianxian Qin, Wenbin Cai

Journal of Electrochemistry

RuO₂/TiO₂ composite materials have multitude of electrocatalytic applications including but not limited to CO₂ reduction reaction (CO₂RR). RuO₂/TiO₂ electrodes were previously prepared by repetitive coating and thermal decomposition (TD) of a Ru(III) precursor solution on Ti substrate. In this work, electrochemical potential cycling is applied to deposit amorphous RuO₂ (α-RuO₂) layers onto TiO₂ nanotube array (TNA) (RuO₂^CV/TNA) preformed on Ti foil. SEM, GIXRD, and voltammetry are applied to characterize the structures of the resulting RuO₂^CV/TNA. Ru loading on the RuO_{2 …}

Design Of 3d Macroporous Inverse Opal Tio2 Binary And Ternary Composites Sensitized With Gold Nanoparticles And Cds Quantum Dots For Photocatalysis, Daniel A. Corella

Master of Science in Chemical Sciences Theses

Materials composed of titanium (IV) oxide (TiO₂) have received enormous scientific interest due to titania’s abundance, non-toxicity, and photocatalytic proficiency, however its large band gap limits its applicability under ambient conditions. Various attempts have been made to incorporate titania into composite systems to sensitize it for activity under a broader range of wavelengths. One such method includes utilizing narrow band gap semiconductors to form an electron transfer process analogous to photosynthesis referred to as a Z-scheme. Z-scheme systems can catalyze the decomposition of aqueous pollutants via generation of reactive oxygen species after input of sunlight. This work reports …

An Expedited, Regiospecific Para-Bromination Of Activated Aryls, Kathryn E. Dudley

Masters Theses & Specialist Projects

Electrophilic Aromatic Substitution (EAS) is one of the most frequently used aryl substitution methods. Aside from the fact that most EAS reactions require an acid and an oxidizer to proceed, the reactions involving activated aryls typically produce a mixture of ortho- and para- products as well as an ortho-/para- disubstituted product. Regiospecificity in aromatic substitution is key in the production of many compounds in a variety of disciplines. Since EAS is one of the most often used substitution methods, it is extremely important to develop an efficient method for regiospecific substitutions. Previous research developed a method of ortho-substitution by using …

Synthesis, Characterization, And Properties Of Graphene-Based Hybrids With Cobalt Oxides For Electrochemical Energy Storage And Electrocatalytic Glucose Sensing, Sara C. Botero Carrizosa

Masters Theses & Specialist Projects

A library of graphene-based hybrid materials was synthesized as novel hybrid electrochemical electrodes for electrochemical energy conversion and storage devices and electrocatalytical sensing namely enzymeless glucose sensing. The materials used were supercapacitive graphene-family nanomaterials (multilayer graphene-MLG; graphene oxide-GO, chemically reduced GO-rGO and electrochemical reduced GOErGO) and pseudocapacitive nanostructured transition metal oxides including cobalt oxide polymorphs (CoO and Co3O4) and cobalt nanoparticles (CoNP). These were combined through physisorption, electrodeposition, and hydrothermal syntheses approaches. This project was carried out to enhance electrochemical performance and to develop electrocatalytic platforms by tailoring structural properties and desired interfaces. Particularly, electrodeposition and hydrothermal synthesis facilitate chemically-bridged …

Technical Feasibility Of Selectively Separating Rare Earth Elements By Vapor Phase Extraction And Condensation, Katie Lyons

Graduate Theses & Non-Theses

Experiments were performed to evaluate the technical feasibility of selectively separating selected rare earth halides (bromides and chlorides) using a volatilization and condensation technique. Initially, optimum chloridizing and bromidizing roast parameters were secured in studies performed on reagent grade rare earth oxide samples and subsequently confirmed in tests performed on mineral ore and concentrate samples. The volatilization and condensation experiments were performed by placing the subject rare earth halide samples in an argon-purged multiple-zone tube furnace wherein the temperature profile was controlled to establish separate vaporization and condensation regions. Following each experiment, condensate and solid residue samples were analyzed to …

Synthesis And Catalytic Applications Of Non-Metal Doped Mesoporous Titania, Syed Z. Islam, Suraj R. Nagpure, Doo Young Kim, Stephen E. Rankin

Chemical and Materials Engineering Faculty Publications

Mesoporous titania (mp-TiO₂) has drawn tremendous attention for a diverse set of applications due to its high surface area, interfacial structure, and tunable combination of pore size, pore orientation, wall thickness, and pore connectivity. Its pore structure facilitates rapid diffusion of reactants and charge carriers to the photocatalytically active interface of TiO₂. However, because the large band gap of TiO₂ limits its ability to utilize visible light, non-metal doping has been extensively studied to tune the energy levels of TiO₂. While first-principles calculations support the efficacy of this approach, it is challenging to …

The Problem Of The Anode Electrolyte In H-Type Electrolytic Cell For Electrochemical Reduction Of Carbon Dioxide, Rui Zhang, Wei-Xin Lv, Li-Xu Lei

Journal of Electrochemistry

Electrochemical reduction of carbon dioxide (CO₂) was studied in the H-type electrolytic cell. It was found that the voltage between the cathode and the anode would increase during the long time electrolysis process, for this reason the electrolytic process would be unsustainable. After the experimental investigations carried out by constant potential electrolysis, constant current electrolysis, pH test and KHCO₃ concentration analysis of anode electrolyte before and after the electrolysis, the increase in cell voltage might be caused by the following process: H⁺, that was generated from the anodic oxygen evolution reaction, reacted with HCO_{3 …}

Application Of Composite Ionic Liquid In Electro-Oxidation Activation Of A C-H Bond, Zi-Ying Chen, Qian-Qian Wu, Jian-Qing Zhang, Ying-Hong Zhu, Chun-An Ma

Journal of Electrochemistry

In this paper, the ionic liquid/carbon nanotube composite material was prepared through modifying the ionic liquid 1-ethyl-3-methylimidazolium acetate to multi-walled carbon nanotubes. The electro-oxidation properties of p-methoxy toluene (p-MT) were studied using the composite as an electrolyte. The effects of scanning speed, temperature and substrate concentration were studied by cyclic voltammetry and chronoamperometry. The electrochemical kinetics of p-MT in this system was also studied. The results showed that the electrochemical oxidation of p-MT in the composite electrolyte solution was irreversible. The process was mainly controlled by diffusion, and the diffusion coefficient (D) was 7.69×10-10 cm²·s^-1. Increasing …

Electrochemical Synthesis Of Porous Polyaniline Electrodes Using Hkust-1 As A Template And Their Electrochemical Supercapacitor Property, Qiong Luan, Chun-Feng Xue, Hong-Ye Zhu, Fu-Juan Yang, Xu-Li Ma, Xiao-Gang Hao

Journal of Electrochemistry

Excellent electrode plays vital important role in the performance of supercapacitors. Polyaniline (PANI) with good conductivity is often used to prepare electrode. However, its available surface is limited and results in a poor supercapacitance in many cases. It is desirable to fabricate an electrode containing electroactive PANI with high surface area deriving from its porous structure. Here, the metal-organic framework (MOF) material with high surface area was selected as a hard template for synthesizing porous PANI. Microporous PANI composite electrodes (Micro-PANI/CC) were fabricated by depositing aniline on to carbon cloth (CC) pre-coated with MOF material of HKUST-1 using a unipolar …

Sn-Doped Α-Fe2O3 Photocatalyst Containing Oxygen Vacancy For Water-Splitting, Zu-Hua Wang, Dong-Fang Niu, Hui-Cheng Li, Rong-Bin Du, Heng Xu, Xin-Sheng Zhang

Journal of Electrochemistry

The α-Fe₂O₃ nanoparticles containing oxygen vacancies were synthesized in atmospheric N₂ by dip-dropping method without a high vacuum employed before annealing. The influences of annealing atmosphere and Sn-doping on the photocatalytic performance of α-Fe₂O₃ nanoparticles were studied by annealing the photocatalyst in N₂ or air and adding SnCl₄ to the precursor directly. The results showed that the current density of Sn-doping α-Fe₂O₃ annealed in N₂ at 550 °C and 1.23 V (vs. RHE) was 35 times greater than that of pristine α-Fe₂O₃ annealed in …

Direct Electrochemistry Of Glucose Oxidase Based On Ws2 Quantum Dots And Its Biosensing Application, Chen-Lu Li, Hua-Ping Peng, Zhong-Nan Huang, Yi-Lun Sheng, Pei-Wen Wu, Xin-Hua Lin

Journal of Electrochemistry

In this study, a novel electrochemical glucose biosensor has been developed by immobilizing glucose oxidase (GOx) on tungsten disulfide quantum dots (WS₂ QDs) on the surface of glassy carbon electrode (GCE). Transmission electron microscopy, UV-vis spectroscopy and cyclic voltammetry were employed to characterize the morphology, structure, and electrochemical behaviors of the as-prepared WS₂ QDs and the biofilm modified electrode. The results suggested that the WS₂ QDs could accelerate the electron transfer between the electrode and the immobilized enzyme, which enabled the direct electrochemistry of GOx without any electron mediator. Besides, the immobilized GOx in WS₂ QDsfilm …

Application Of Adamantane Schiff Base Nickel Complexes/Graphene Oxide/Glassy Carbon Modified Electrode In Detection Of Carmine, Peng Guo, Zheng Liu, Hai-Ying Li, Li-Ming Ma

Journal of Electrochemistry

The Schiff base nickel complexes/graphene oxide/glassy carbon electrodes were prepared by embedded method and electrodeposition on which were used to quantitatively detect the contents of carmine. Cyclic voltammetry, chronoamperometry, scanning electron microscopy (SEM) and other methods were employed to characterize properties and morphologies of the modified electrodes. The results show that the adamantane double Schiff base nickel complexes/graphene oxide/glassy carbon electrode had high electric catalytic activity toward carmine oxidation reaction, and might provide an easy and quick way to detect carmine content with good reproducibility.

Geometry-Driven Folding Of A Floating Annular Sheet, Joseph Paulsen, Vincent Démery, K. Buğra Toga, Zhanlong Qiu, Thomas P. Russell, Benny Davidovitch, Narayanan Menon

Physics - All Scholarship

Predicting the large-amplitude deformations of thin elastic sheets is difficult due to the complications of self contact, geometric nonlinearities, and a multitude of low-lying energy states. We study a simple twodimensional setting where an annular polymer sheet floating on an air-water interface is subjected to different tensions on the inner and outer rims. The sheet folds and wrinkles into many distinct morphologies that break axisymmetry. These states can be understood within a recent geometric approach for determining the gross shape of extremely bendable yet inextensible sheets by extremizing an appropriate area functional. Our analysis explains the remarkable feature that the …

Going Green: Experimental Adaptation Of Scenedesmus Dimorphus To Marine Conditions, Mohammed Khalil

Undergraduate Research Posters 2017

Algae has gained some interest as the need for alternative fuels becomes more pressing. Reliance on fossil fuels is causing our environment and economy harm, and is not sustainable moving forward. Lipid rich algae strains can be used in the production of biofuels, and provide an alternative fuel source. One challenge facing the prospect of algae as a fuel source is that lipid rich algae grows exclusively in freshwater. Considering the scarcity and cost to use freshwater for algae growth, interest has grown in the possibility of adapting lipid rich, freshwater algae to a seawater environment. Seawater can have up …

Evaluation Of Cetane Values Of Glycerolipids Extracted From Algae Scenedesmus Dimorphus Grown In Various Salinity Concentrations Using Gas Chromatography And Mass Spectrometry (Gc-Ms), Paul Lin, Chandana Mannem

Undergraduate Research Posters 2017

Algae's ability to store lipids, renewability, and potentially safer for the environment has made it a promising alternative fuel source. An industry rating for a biofuel's potential is the cetane value, which is a measure of a fuel's quality related to various glycerolipid concentrations. Growing conditions will affect lipid profile in algae, thereby affecting the cetane value. This project will attempt to identify changes in the centane value of the algae Scenedesmus dimorphus grown in various salinity concentrations. Scenedesmus dimorphus is the algae chosen for this experiment because of its ability to rapidly grow under harsh conditions. In this experiment …

P1: Salt Concentration And Ph Affect The Size Of Elastin-Like Polypeptide Nanoparticles, Bryce Noe, Ilona Tsuper, Daniel Terano, Richard Schmitt

Undergraduate Research Posters 2017

The transport of therapeutic drugs to specific tissues in the body can be accomplished using nanoparticles that encapsulate the drugs. Elastin-like polypeptides (ELP) is a class of materials that can reversibly form such nanoparticles in response to environmental cues. FLPs transition from soluble compounds to a phase separated system under particular solution conditions and have been used to produce temperature responsive surfactants. When these ELP surfactants are above their transition temperature, they spontaneously form energetically stable spherical micelles. When the temperature drops below the transition temperature, the micelles break apart and the ELP goes into solution. The size of these …

P2: Light Scattering Study Of The Size And Shape Of Mixed Elastin-Like Polypeptide Micelles, Ilona Tsuper, Daniel Terrano, Bryce Noe

Undergraduate Research Posters 2017

Elastin-Like Polypeptides (ELP) can be used to form thermoreversible vehicles for drug delivery systems. The ELP nanoparticles are composed of three-armed star polypeptides. Each of the three arms extending from the negatively charged foldon domain include 20 repeats of the (GVGVP) amino acid sequence. In addition, linear constructs composed of 40 repeats of the same (GVGVP) sequence are introduced into the system. The mixed ELP polymer system is soluble at room temperature and becomes insoluble at the transition temperature (~ 50°C) forming micelles with the foldons on the exterior and linear constructs at the core. Above the transition, the size …

Synthesis, Characterization, And Activity Of Co/Fe Alumina/Silica Supported Ft Catalysts And The Study Of Promoter Effect Of Ruthenium, Sunday Azubike Esumike

Doctoral Dissertations

The alumina and hybrid alumina-silica FT catalyst were prepared by one-step solgel/oil-drop methods using metal-nitrate-solutions (method-I), and nanoparticle-metaloxides (method-2). The nanoparticle-metal-oxides did not participate in solubility equilibria in contrast to metal nitrate in method-1 causing no metal ion seepage; therefore, method-2 yields higher XRF metal loading efficiency than method-1. The thermal analysis confirmed that the metal loading by method-1 and method-2 involved two different pathways. Method-1 involves solubility equilibria in the conversion of metal-nitrate to metal- hydroxide and finally to metal-oxide, while in method-2 nanoparticle-metal-oxide remained intact during sol-gel-oil-drop and calcination steps.

The alumina supported catalysts were dominated by γ-alumina …

Biomimetic Devices To Drive A Thermodynamically Uphill Reaction Using Light And To Degrade Industrial Waste Stream Components, Madison Joanne Sloan

Theses and Dissertations--Chemistry

Given the amount of industrial waste produced each year, as well as the accruing amount of greenhouse gases in our atmosphere produced by the burning of fossil fuels, it is imperative that humanity develop environmentally-sustainable sources of energy and methods of remediation. Nature achieves both of these by use of enzymes as catalysts, inspiring interest in designing biomimetic systems capable of harnessing clean energy and remediating industrial waste. This study examined the ability of enzymes in electrochemical and convective flow systems to achieve these tasks. The first portion studied the incorporation of enzymes into an electrochemical system to drive the …

Preparation And Application Of Catalysts For The Stereospecific Reduction And Photooxygenation Of Olefins In Continuous Operations: A Novel Method For The Production Of Artemisinin, Daniel C. Fisher

Theses and Dissertations

Over the last two centuries, the discovery and application of catalysts has had a substantial impact on how and what chemicals are produced.Given their broad significance, our group has focused on developing new catalyst systems that are recoverable and reusable, in an attempt to reduce concomitant costs.

Our efforts have centered on constructing a recyclable chiral heterogeneous catalyst capable of effecting asymmetric hydrogenations of olefins with high stereoselectivity. A class of phosphinoimidazoline ligands, developed by researchers at Boehringer-Ingelheim, known as BIPI ligands, have proven efficacious in the asymmetric reduction of alkenes. However, these chiral ligands are homogeneous and coordinated to …

A Miniaturized Spectrophotometric In Situ Ph Sensor For Seawater, Reuben C. Darlington

Graduate Student Theses, Dissertations, & Professional Papers

Since the Industrial Revolution, the world's oceans have absorbed increasing amounts of CO2 and the resultant changes to the marine carbonate chemical system have reduced the pH by > 0.1 units (~ 30%) in surface waters. This acidification of the oceans has many far reaching impacts on marine life and there is great need of quality instrumentation to assess and follow the changing carbonate system. This MIS project aims to develop a low cost pH sensor with high precision and accuracy for open sea measurements with special emphasis on reduced size and cost. Design effort is based on the commercially available …