Bioresource and Agricultural Engineering Commons^™

Regional Variation In Temperature Humidity Index For Poultry Housing, Richard S. Gates, Hanzhong Zhang, Donald G. Colliver, Douglas G. Overhults

Biosystems and Agricultural Engineering Faculty Publications

A building thermal model was used to compute hourly values of temperature humidity index (THI) for a broiler house with and without an evaporative misting system. Hourly summer time weather data for 238 U.S.A. locations covering 30 years were used to develop extreme occurrences of THI. Results were incorporated into a Geographical Information System (GIS) database to create isolines of THI and percentage of hours exceeding a heat stress threshold. Regional variations in misting as a suitable cooling technique are presented in terms of hours reduction in annual heat stress. The technique may be used for assisting in management decisions …

Field Calibration Of A Transient Model For Broiler Misting, Richard S. Gates, Douglas G. Overhults, Robert W. Bottcher, Shu Hui Zhang

Biosystems and Agricultural Engineering Faculty Publications

A transient model to predict temperature within a tunnel ventilated broiler house during misting is developed. The model is calibrated with field data to obtain steady-state constants; transient predictions are compared to measured temperatures during cyclic misting for two different size birds. Measured temperatures during cyclic misting are shown to swing between steady-state asymptotes predicted from the model. Transient response of the model was faster than measured temperature data, in part due to temperature sensor dynamic response. The model predicts the length-wise temperature profile within the building during misting, and can be used to investigate alternate misting strategies and designs. …

Mechanical Backup Systems For Electronic Environmental Controllers, Richard S. Gates, Douglas G. Overhults, Larry W. Turner

Biosystems and Agricultural Engineering Faculty Publications

A series of mechanical backup systems for electronic environmental controllers is presented for a typical finishing swine barn and a typical tunnel ventilated broiler house. The systems consist of mechanical thermostats and timers used in parallel with the electronic controller, designed to ensure animal survival in the event of controller or related hardware failure. For swine housing, three distinct mechanical backup functions are identified; for broiler housing, four distinct mechanical backup functions are identified. Schematic diagrams of the mechanical backup functions are provided and their implementation is described.

A Survey Of Electronic Environmental Controllers, Richard S. Gates, Douglas G. Overhults, Larry W. Turner

Biosystems and Agricultural Engineering Faculty Publications

Sixteen commercially available electronic environmental controllers were evaluated. The units were classified according to enclosure type, analog versus microprocessor based control, power supply, sensors, alarms, control relays and triac output, interval timers, outside temperature feedback, and retail price. An assessment of these controllers indicated several critical limitations in the application of this technology.

The use of integrated controllers for animal production has the potential for substantial improvements in production efficiencies. If the limitations observed in the present controller technology, as represented by this sample, are addressed, industry acceptance of the technology can be accelerated. A uniform standard to address this …

Transient Overvoltage Testing Of Environmental Controllers, Richard S. Gates, Larry W. Turner, Douglas G. Overhults

Biosystems and Agricultural Engineering Faculty Publications

The integrated electronic control system will provide a new method for the day-to-day management of environmental control of animal production systems. No standards are currently accepted for transient overvoltage protection of these controllers. To assess the adequacy of existing designs, a test circuit was designed and used for a transient open circuit over-voltage waveform (ANSI/IEEE C62.41-1980) of 16 environmental control units: a maximum spike of 770 V was applied to the power supplies, and a spike up to 100 V was applied to temperature sensor lines. For these relatively mild tests, no failures were noted due to power supply transients, …

Compact – A Reclamation Soil Compaction Model Part I. Model Development, Ronald L. Bingner, Larry G. Wells

Biosystems and Agricultural Engineering Faculty Publications

A physically based, event oriented soil compaction model, known as COMPACT, was developed as a management or research tool to evaluate the effect of surface mining systems on compaction of soil material during reclamation. Simulation of compaction throughout the soil profile at a surface mining reclamation site requires information describing how equipment moves on the site. The compaction processes that are caused by vehicles throughout the soil profile are described by applying the pressure distribution of the surface contact area of a tire or track to determine stresses in the soil profile. A virgin compression curve is then used to …

Compact – A Reclamation Soil Compaction Model Part Ii. Sensitivity Analysis And Applications, Ronald L. Bingner, Larry G. Wells

Biosystems and Agricultural Engineering Faculty Publications

COMPACT, a physically based, event-oriented compaction model, was developed as a management or research tool to evaluate the influence of a surface mining system on compaction of soil material during reclamation. Two systems of area mining reclamation operations were simulated by COMPACT. The first system involved scrapers and bulldozers and the second also included trucks. Scrapers or trucks were used to pick up and deposit the soil material. Bulldozers were then used to shape the site for reclamation. The simulated results were compared with measured results and show how equipment patterns and soil parameters can affect overall soil compaction. This …

Evaluation Of Gamma Ray Attenuation For Measuring Soil Bulk Density Part I. Laboratory Investigation, Xiwen Luo, Larry G. Wells

Biosystems and Agricultural Engineering Faculty Publications

Gamma ray attenuation was evaluated as a means of determining soil bulk density. Experiments were conducted using clay, silt, and sandy loam soils wherein samples were compacted to uniform densities at various moisture contents. We determined the attenuation characteristics of dry soil to be independent of soil texture while being significantly different from that of water. Comparison of gamma density measurements with known soil sample densities indicated that the gamma gauge provided reliable measurement of soil bulk density, provided that the effect of soil moisture on attenuation was accounted for and the manufacturer-prescribed calibration procedure was followed daily. Further, we …

Evaluation Of Gamma Ray Attenuation For Measuring Soil Bulk Density Part Ii. Field Investigation, Larry G. Wells, Xiwen Luo

Biosystems and Agricultural Engineering Faculty Publications

A field investigation was conducted at sites near Lexington and Central City, Kentucky, to evaluate the use of gamma ray attenuation for measuring soil bulk density. Experiments were conducted whereby the gamma gauge was calibrated by various means and compared with volumetric cores collected from the field soils. Calibration by the manufacturer’s recommended procedure was determined to be as accurate as more rigorous laboratory calibration or calibration via regression of soil bulk density data, provided that the effect of soil water on gamma attenuation is correctly considered. We also developed a linear regression equation to correct for the occurrence of …

Curling Burley Tobacco From An Automated Harvesting System, Linus R. Walton, Larry G. Wells, James H. Casada

Biosystems and Agricultural Engineering Faculty Publications

If burley tobacco can be successfully cured at high density under waterproof covers in the field, a producer can expand production without the necessity of building new curing barns and can thereby more easily justify investment in the automated burley tobacco harvesting system (Wells et al., 1990a, b). Curing under waterproof covers in the field and curing on frames in the barn were evaluated over three curing seasons using two varieties (KY 14 and TN 86), two plant densities (32 and 43 plants/m², 3 and 4 plants/ft²), position of tobacco on the frame (four levels ranging …

Elliptical Combing Motion For Harvesting Bell Peppers, J. H. Wilhoit, George A. Duncan, Larry G. Wells

Biosystems and Agricultural Engineering Faculty Publications

A new concept for mechanically harvesting bell peppers, intended specifically for multiple-pass harvesting, utilized spaced horizontal fingers combing vertically upward through plant foliage in an elliptical path alternating from both sides of the row. An apparatus based on this concept was designed and built, and harvest tests were conducted to determine the effect of two main machine operating parameters, vertical picking speed and disk angle. Harvesting performance was evaluated in terms of harvest efficiency, fruit damage, and plant damage as it related to multiple-pass harvesting. Fruit removal, both harvestable size and immature, increased significantly as vertical picking speed increased. Branch …

Automated Harvesting Of Burley Tobacco Ii. Evaluation Of System Performance, Larry G. Wells, George B. Day V, Timothy D. Smith

Biosystems and Agricultural Engineering Faculty Publications

A prototype system for fully automated harvesting of burley tobacco has been developed and tested. Three years of field testing has shown that mechanical losses associated with the system were only slightly higher than via conventional methods. The system performed reliably at a sustained harvesting rate of approximately 1.4 ha/day (3.4 acre/day), while indicating that a rate of 2 ha/day (5 acre/day) should be easily achievable. The system is operated by two workers and reduces conventional labor requirement by approximately 80-85%.

Automated Harvesting Of Burley Tobacco I. System Development, Larry G. Wells, George B. Day V, Timothy D. Smith

Biosystems and Agricultural Engineering Faculty Publications

A fully automated system for harvesting and handling mature buriey tobacco has been developed. This article identifies the operations essential to this harvesting concept and describes the development of the mechanisms by which they were accomplished. The system detaches, inverts and places mature plants into portable holders for air curing under waterproof covering without requiring any manual handling of the crop. Manual labor currently required to harvest buriey tobacco would be reduced by 80-85% and the system would eliminate the drudgery associated with manual handling. The harvesting system has an approximate capacity of 1.4 to 2.0 ha/day (3.5 to 5.0 …

Pneumatic Metering Of Hardwood Tree Seeds, Larry G. Wells, T. W. Richards, Timothy D. Smith, George B. Day

Biosystems and Agricultural Engineering Faculty Publications

A commercial, no-till row planter was extensively modified for use in direct seeding of hardwood tree species in surface mine reclamation. A pneumatic seed metering system was designed, fabricated, and mounted on the planter frame.

The metering device was tested under laboratory conditions which simulated varying terrain slope and field speed with seeds of various hardwood tree species. Metering efficiencies of 97% were achieved for pin oak seeds at 3.2 km/hr (2.0 m/h) and 50% slope. For red oak, 97% efficiency was achieved for 50% slope at 4.0 km/h (2.5 mph). Unsatisfactory metering was noted during tests of larger seeds, …

Automated Sorting Of Oriented Tobacco Leaves, Larry G. Wells, M. J. Bader

Biosystems and Agricultural Engineering Faculty Publications

A mechanism has been developed which removes cured burley tobacco leaves from plants so that midribs are oriented parallel. A photosensor was utilized to count leaves as they were removed and a microprocessor determined the number of leaves allocated to each of three grades. Experiments indicated that 84% of leaves removed could be correctly sorted with a 2.4% material loss at an effective rate of approximately 2.4 times that of conventional methods.

An Aeration Duct Design Model For Flat Grain Storage, Thomas C. Bridges, Douglas G. Overhults, Samuel G. Mcneill, G. M. White

Biosystems and Agricultural Engineering Faculty Publications

Traditionally most grain is stored in circular type bins which provide a convenient means for handling and management. With the excess grain production and government loan programs of the past few years, some producers have used rectangular structures and covered piles to complement their round storages. The recommended management practices used with round bins are still required in those alternative storages and may be more critical in obtaining a quality end product.

One such recommended practice used with round bins is aeration. This practice is used to maintain a uniform temperature in the grain mass, preventing condensation and "hot" spots …

Production Of Aflatoxin On Damaged Corn Under Controlled Environmental Conditions, D. M. Wieman, G. M. White, Joseph L. Taraba, I. J. Ross, Clair L. Hicks, Bruce E. Langlois

Biosystems and Agricultural Engineering Faculty Publications

Aflatoxin B₁ production by Aspergillus flavus (NRRL 6432) was determined on physically damaged corn stored at 35,25 and 20°C and at relative humidities of 97 and 92%. Production at lower relative humidities of 80 and 85% were also tested at 25°C. Production lag times were significantly different for all test conditions. Lag times ranged from 46 h at 97% relative humidity and 35°C to 173. 8 h at 20°C and 92% relative humidity. Aflatoxin B, concentration doubled every 6 to 10 hours after a level of 10 ppb had been reached. Production rate constants were not significantly different between …

Comparison Of Four Infiltration Models In Characterizing Infiltration Through Surface Mine Profiles, Larry G. Wells, A. D. Ward, I. D. Moore, R. E. Phillips

Biosystems and Agricultural Engineering Faculty Publications

A laboratory infiltrometer system was used to evaluate the infiltration process through reconstructed surface mine profiles. Six different profiles were subjected to constant simulated rainfall intensities for selected test conditions. Surface runoff rates were monitored and transient soil moisture contents in the profiles were measured with a gamma density gauge. Unsaturated hydraulic conductivity relationships were determined using Campbelfs method and the "zero-flux" procedure. The infiltration process was modeled by the SCS curve number method, a form of Holtan's equation, the Green-Ampt model and Richards' equation. SCS curve numbers were determined by fitting the method to the observed results. Richards' equation …

Traction Characteristics Of Prepared Traffic Lanes, Eddie C. Burt, James H. Taylor, Larry G. Wells

Biosystems and Agricultural Engineering Faculty Publications

Traction characteristics of lugged and smooth tires were compared on prepared traffic lanes and on conventional seedbed conditions. Results indicated that elevated traffic lanes offer important traction advantages over seedbeds in wet soil conditions. In dry soil conditions, traction on elevated traffic lanes was sometimes less than on the seedbed conditions. A timeliness advantage in mobility for the elevated traffic lanes was found to be up to 2 days in extremely wet conditions. A non-elevated traffic lane showed no traction advantage in wet conditions.

Characterizing Soil Deformation By Direct Measurement Within The Profile, Randall K. Wood, Larry G. Wells

Biosystems and Agricultural Engineering Faculty Publications

A unique feature of the University of Kentucky soil bin enables deformation to be characterized by studying a cross-sectional soil profile grid pattern. Modular sections of the bin are laterally removed to expose the cross-section after passes of a pneumatic tire.

The measured displacements of the grid points were converted to values of volumetric strain and then compared to soil density as measured by a dual probe gamma-ray density gauge following tests at various soil conditions. Final soil bulk density determinations using the two methods were not statistically different..

Storage Of Burley Tobacco In Bales And Bundles, Linus R. Walton, M. E. Casada, Joseph L. Taraba, James H. Casada, W. H. Henson Jr., Larry D. Swetnam

Biosystems and Agricultural Engineering Faculty Publications

Bales and bundles of burley tobacco were stored for seven months from spring to fall. Leaves darkened during storage at all moisture levels and stalk positions with the exception of the bottom stalk position, which darkened only slightly. There was no difference in color change and dry weight loss between burley tobacco in bales and bundles. Normal and high moisture bales and bundles were often graded as unsound because of a deviant odor caused by bacterial activity. A bale weight loss of about 8% occurred at normal moisture with the loss being divided evenly between moisture and dry weight losse.

Equilibrium Moisture Properties Of Corn Cobs, G. M. White, Thomas C. Bridges, Samuel G. Mcneill, Douglas G. Overhults

Biosystems and Agricultural Engineering Faculty Publications

Equilibrium moisture content-equilibrium relative humidity data for broken corn cobs have been determined for both desorption and adsorption conditions for three temperature levels and five moisture levels. The Modified Henderson and Chung equilibrium moisture equations have been fitted to these data by using non-linear regression procedures to estimate equation parameters. Both equations adequately represented the experimental data. A test of varietal differences indicated no significant difference in cob desorption ERH values for three selected corn varieties.

Retention Of Gasification-Combustion Products By Corn, S. W. Sizemore, Otto J. Loewer, Joseph L. Taraba, I. J. Ross, G. M. White

Biosystems and Agricultural Engineering Faculty Publications

Shelled corn was dried in layers of 5.1 cm (2 in.) 10.2 cm (4 in.), and 15.2 cm (6 in.) using air heated with the exhaust from a corn-cob fueled gasification-combustion updraft furnace. The drying air entering and leaving the grain layers was sampled for particulate content to determine the percentage of total particulates trapped by the grain during drying. It was determined that an average of 25% of the total particulates in the drying air were retained by the grain. The large majority of those particulates retained were found in the bottom 5.1 cm (2 in.) of the grain …

Limiting Swine Stress With Evaporative Cooling In The Southeast, Robert L. Fehr, K. T. Priddy, Samuel G. Mcneill, Douglas G. Overhults

Biosystems and Agricultural Engineering Faculty Publications

Three-hourly weather data for 7 locations in the Southeast and Central United States were used to evaluate the feasibility of evaporative cooling for reducing swine stress. Stress was defined as a relationship between dry and wet bulb temperatures which exceeded a stress index of 85. This analysis indicates that properly installed evaporative coolers could reduce the number of hours that stress would occur in swine facilities from 89.6 to 96.4% depending on location.

Infiltration Through Reconstructed Surface Mined Spoils And Soils, A. D. Ward, Larry G. Wells, R. E. Phillips

Biosystems and Agricultural Engineering Faculty Publications

An extensive series of tests involving reconstructed profiles of spoil and topsoil material from a Western Kentucky surface mine site was conducted with a laboratory infiltrometer system. Infiltration through the reconstructed spoil profiles was very slow despite the coarse nature of the material. Low infiltration rates could be attributed to the material having a well-graded texture and to the high densities of the profiles. Infiltration through topsoil horizons was controlled, for the most part, by conditions at the surface. Following wetting, infiltration rates were primarily controlled by the hydraulic characteristics of the less permeable sub horizon of the spoil material. …

Effect Of Herbicides On Performance Of Aerobic Dairy Lagoons, John D. Bottom, Joseph L. Taraba

Biosystems and Agricultural Engineering Faculty Publications

The herbicides glyphosate, bromacil, and dalapon were assessed for their affect on the oxygen uptake of microorganisms from an aerated dairy lagoon at 20 °C. The maximum recommended addition of herbicide active ingerdient to a lagoon is: glyphosate (isopropyl amino salt)—0.42 mg/L; bromacil—3.70 mg/L; and dalapon (85.8 percent Na salt and 14.2 percent Mg salt)—1.95 mg/L. In addition, microorganism isolates from the aerobic dairy lagoon were incubated under aerobic and anerobic conditions at room temperature to assess the effects of the herbicides. Under aerobic incubation, it was found that neither herbicide type nor herbicide concentration affected isolate growth. Under anaerobic …

Vertical Wall Loads In A Model Grain Bin, S. A. Thompson, I. J. Ross, John N. Walker, Larry G. Wells

Biosystems and Agricultural Engineering Faculty Publications

No abstract provided.

Temperature And Humidity Prediction In A Burley Curing Facility, Thomas C. Bridges, Linus R. Walton, Larry G. Wells, I. J. Ross

Biosystems and Agricultural Engineering Faculty Publications

No abstract provided.

Simulation Of Burley Tobacco Harvesting-Housing Systems, Ronald L. Bingner, Larry G. Wells, Thomas C. Bridges, George A. Duncan

Biosystems and Agricultural Engineering Faculty Publications

A computer model has been developed using systems analysis techniques to simulate the labor and equipment aspects of harvesting burley tobacco. By varying the parameters of the model the user can determine a harvesting and housing strategy based on labor and equipment availability.

A Simulation Model For Assessing Alternate Strategies For Beef Production With Land, Energy And Economic Constraints, Otto J. Loewer, E. M. Smith, G. Benock, Thomas C. Bridges, Larry G. Wells, Nelson Gay, S. Burgess, L. Springate, David L. Debertin

Biosystems and Agricultural Engineering Faculty Publications

A computer model has been developed to analyze alternate management strategies and energy and economic constraints. Daily production of beef animals and growing crops is simulated in response to prevailing conditions and system interactions using the GASP IV simulation language. Complete inventories of plant dry matter, animal status, production resources and economic net worth are maintained over the simulation period.