Bioresource and Agricultural Engineering Commons^™

Using Net Groundwater Extractions For Farm Level Groundwater Sustainability Monitoring, Daniel J. Howes, Morgan Whinery, Eric Limas, Dan Vink

BioResource and Agricultural Engineering

The Cal Poly Irrigation Training and Research Center (ITRC) has developed a method for computing net groundwater extraction and recharge at the farm level for district management and regulation of sustainable/safe yields. This method is called Net To/From Groundwater (NTFGW). Net groundwater extraction is preferred for assessing sustainable yield in unconfined aquifer systems over direct metering of gross groundwater pumping. A recent pilot project with the Lower Tule River and Pixley Irrigation Districts’ Groundwater Sustainability Agencies (GSAs) compared actual metered groundwater pumping, surface deliveries, and evapotranspiration to the NTFGW outputs on 19 farms within the GSAs over a 3-year period …

An Assessment Of The Greatest Impacts On Distribution Uniformity For Drip And Micro Irrigation, Brooke Ashley Worden

Master's Theses

Using the Cal Poly Irrigation Training and Research Centers (ITRC) drip/micro evaluation program, global, or system, DU_lq is computed by combining the component DU_lq values of: pressure variation, uneven spacing between emitters, unequal drainage and “other” causes. “Other” causes include plugging, wear and manufacturing coefficient. The program also computes what percentage of the non-uniformity is due to each component. Burt (2004) showed that over 95% of the non-uniformity is due to “Other” causes and pressure differences. This thesis looks at what specifically in those components is driving the non-uniformity by analyzing various equipment and field practices and their …

Water Hammer Protection For Pumped Turnouts On Aging Pipelines, Charles M. Burt, Zachary C. Markow

BioResource and Agricultural Engineering

Water hammer in an irrigation district pipeline is typically caused by sudden changes in turnout flow rates. A sudden shutoff of a booster pump, or a rapid closure of a turnout valve, can potentially cause surge damage. The problem occurs if the pressure exceeds the pressure rating of the pipeline. As pipes age, their pressure rating typically declines. This report describes three different solutions that utilize a combination of these techniques/devices to provide district pipeline protection from water hammer.

Developing, Evaluating, And Demonstrating An Open Source Gateway And Mobile Application For The Smartfarm Decision Support System, Caleb D. Fink

Master's Theses

The purpose of this research is to design, develop, evaluate, and demonstrate an open source gateway and mobile application for the SmartFarm open source decision support system to improve agricultural stewardship, environmental conservation, and provide farmers with a system that they own. There are very limited options for an open source gateway for collecting data on the farm. The options available are: expensive, require professional maintenance, are not portable between systems, improvements are made only by the manufacturer, limited in customization options, difficult to operate, and data is owned by the company rather than the farmer. The gateway is designed …

A Review Of Subsidence Measurements Near Mendota, California, Tom Mastin, Stuart Styles, Kyle Feist

BioResource and Agricultural Engineering

The image of Dr. Poland of the United States Geological Survey (USGS) standing next to a marked powerline in 1977 is circulated as a striking example of land subsidence. This and other historical data are common references for modern subsidence studies. Because of the significance of this data, recent work was conducted to analyze the historical data as well as independently measure the magnitude of subsidence since 1975, within the same study area southwest of Mendota, CA. The results indicate that local subsidence in the area of the photo is less than 0.5 meters between 1975 and 2017. Furthermore the …

Case Study: Flow Measurement And Control In Walker River Irrigation District, Stuart Styles, Sierra Layous, Robert Bryan

BioResource and Agricultural Engineering

Walker River Irrigation District (WRID) is located in Nevada around the community of Yerington and contains approximately 95,000 hectares (235,000 acres), 32,000 hectares (80,000 acres) of which are irrigated. The district operates a canal system centered around the three forks of the Walker River. Starting in 2009, the district has worked with the Irrigation Training and Research Center (ITRC) to modernize its system by improving the accuracy of the measured diversions from the Walker River and enhancing the real-time control capabilities of the water managers. A “package” was developed for the headworks of canals diverting water from the river, consisting …

Safety Videos For Major Shop Equipment In Cal Poly Brae Lab 1, Trey Joseph Johnston

Agricultural Education and Communication

At California Polytechnic State University, San Luis Obispo, students from all majors can take a variety of classes in the BioResource and Agriculture Engineering Department (BRAE). It is essential for future high school mechanics educators to learn the basic shop tools and the importance of safety in the laboratory. In shop 1 of the BRAE Department, there are many different tools students will find in a mechanics classroom. The five main power tools are the Table Saw, Drill Press, Bench Grinder, Radial Arm Saw, and Disk/Belt Sander.

In BRAE 121 Agricultural Mechanics, students learn basic shop skills about lab safety …

Scada System Maintenance: An Often Overlooked Necessity, Charles M. Burt, Kyle Fesit

BioResource and Agricultural Engineering

The design and implementation of a Supervisory Control and Data Acquisition (SCADA) system is typically undertaken by expert engineers and integration contractors. In order to provide a robust and reliable SCADA system, good design and installation practices are required. Preserving the initial SCADA system reliability requires good maintenance. Unfortunately, SCADA maintenance is often overlooked or underestimated. There are two potential providers for SCADA maintenance activities. Some SCADA maintenance activities are best provided by the developer or installer of the SCADA system, before closing out a project contract. Other SCADA maintenance requirements are best provided by the irrigation district or SCADA …

A New Approach To Vfd System Specifications And Rebates, Kyle Feist, Randall Cole, Charles M. Burt

BioResource and Agricultural Engineering

Variable frequency drives (VFDs) are used to provide flexibility and efficiency enhancements for agricultural pressurized irrigation systems. Standard 6-pulse VFDs commonly used for agricultural pumps can also create real problems with the pump motor and nearby electrical systems, unless mitigated by special equipment.

With support by the California Polytechnic State University (Cal Poly) Irrigation Training and Research Center (ITRC), Pacific Gas and Electric Company (PG&E) recently began a new rebate program for installing VFD systems for pressurized irrigation. A major component of the new rebate program is the requirement to comply with a detailed set of minimum VFD system design …

Modernizing Aging Pipe Infrastructure In Irrigation Districts, Charles M. Burt, Kyle Feist, Zachary Markow

BioResource and Agricultural Engineering

Many irrigation and water districts in California convey water through aging concrete pipelines. In addition to huge problems with leaks and failures, districts also struggle to provide turnout deliveries with more flexible schedules. This paper discusses the problems that are encountered, and various approaches that have been or can be used. The specific pipeline designs that are discussed in this paper are generally gravity flow, flowing downhill from a canal. Most of these pipelines were originally installed under the assumptions that farmers would need high flows at low pressures for surface irrigation.

Case Study: Modernization Of The Walker River Irrigation District, Stuart Styles, Robert C. Bryan, Sierra Layous

BioResource and Agricultural Engineering

The Irrigation Training and Research Center (ITRC) and Walker River Irrigation District (WRID) collaborated on the modernization of WRID with support from the Bureau of Reclamation, U.S. Department of Interior in Carson City, Nevada. This paper presents an update to the USCID case study that was presented in 2014 on the initial proposed plan for improving water gauges throughout WRID. There has been phased implementation of the initial proposed plan as well as modification and expansion of that plan. The initial scope of work for system improvements was developed by ITRC in 2009 following field investigations and engineering analyses of …

Smartfarm, Nathan A. Oto, Caleb Fink

Computer Engineering

The overall expectation of this product is to create an autonomous Arduino library that accurately and robustly collects plant environment data from the Smart Farm board. The Smart Farm PCB is split into two primary functions: Data Acquisition(DAQ) and Power Control. Each function of the PCB is controlled by an Atmega 328P Microcontroller. The primary concern for this report is the functionality of the DAQ microcontroller.

Kettle Cooling And Sustainability Project, Nico Degiorgio

BioResource and Agricultural Engineering

A particular frozen food processing facility uses a once-through cooling process to bring their kettle-cooked product’s temperature down from nearly boiling temperatures to the eighty degree Fahrenheit range. This process is water intensive and facility managers are seeking to reduce their potable water consumption. Sales engineers from Air Treatment Corporation, an HVAC&R manufacturers’ rep, initiated a number of meetings to propose heat rejection solutions and illustrate their associated payback potentials.

This report contains methods of analyzing a food production process, the technical sales process, thermodynamic principles, refrigeration technologies, and the application of technical knowledge to provide a long-term, system solution. …

Improving Flow Measurement Accuracy Using A Portable Irrigation Turnout Calibration Unit, Stuart Styles, Kyle Feist, Charles M. Burt

BioResource and Agricultural Engineering

Relatively accurate flow measurement at irrigation district water delivery points is an important component of volumetric billing and equitable service. In California, this has often occurred with conversions to pressurized irrigation systems which commonly include the installation of pipeline flow meters as part of the on-farm system. However, a large portion of irrigation turnouts in the western US continue to operate via gravity and fall into one of the following categories: (a) a metergate, or similar structure was installed without adherence to standard construction requirements or (b) the structure was never intended for flow measurement.

For these and other scenarios, …

Using Electricity Consumption To Estimate Water Volumes Pumped From Wells, Charles M. Burt

BioResource and Agricultural Engineering

The Sustainable Groundwater Management Act (SGMA) of California has led some organizations to want access to documentation of the volumes of groundwater pumped by individual wells. Many well pumps already have flow meters installed that provide an accurate measurement of both instantaneous flow rate and the cumulative volume pumped. For wells that do not have flow meters, it has been proposed for many years that pumped volumes can be accurately estimated by simply using the total power consumption, measured in kilowatt-hours (kWh).

Influence Of Supply-Channel Velocity On Farm Delivery Meter Gate Flow Measurement, Daniel J. Howes, Charles M. Burt, John M. Thorburn

BioResource and Agricultural Engineering

The work presented here is an extension of previous papers that updated the calibration of round (Armco-type) meter gates (three sizes: 0.30, 0.46, and 0.61 m), developed ratings for rectangular gates (two sizes: 0.46 and 0.61 m) on round pipes, and examined errors and uncertainty related to using these devices for water discharge measurement. Previous works examined gate discharge ratings under low supply-channel flow velocity perpendicular to the gate discharge pipeline. Here, additional testing was conducted to test the hypothesis that higher velocities in the supply channel would show decreased meter gate flow compared to the low-velocity ratings, but that …

Managing Drip Filter Backflush Water, Charles M. Burt

BioResource and Agricultural Engineering

The paper discusses the principles of backflushing different types of filters, as well as pressure and flow requirements for proper backflushing of various filters. Additionally, it discusses options for what to do with the backflush water. A prototype ITRC design for cleaning and recycling backflush water is presented.

Identification Of Agricultural Land Use In California Through Remote Sensing, Todd Allen Robinson

Master's Theses

Ground truthing actual crop types in an area can be expensive and time-consuming. The California Department of Water Resources attempts to ground truth land use in each county in California every five years. However, this is limited by budgetary constraints and often results in infrequent (more than every ten years) surveying of many counties. An accurate accounting of crops growing in a region is important for a variety of purposes including farm production estimates, groundwater and surface water modeling, evapotranspiration estimation, water planning, research applications, etc. Agricultural land use is continually changing due to development and environmental factors.

Currently, USDA …

The Design And Construction Of A Rear Bumper With Incorporated Spare Tire Rack, Alan C. Isaacson

BioResource and Agricultural Engineering

This senior project outlines the design and construction of a rear bumper with incorporated spare tire and equipment rack for a 1946 Willys CJ2A Jeep. The spare tire rack is capable of swinging out away from the vehicle to allow for the use of the vehicle’s tailgate. The bumper was designed for strength, functionality and aesthetic qualities alike. Additionally, the bumper design considered all vehicle codes and regulations.

Testing Feasibility Of Inductive Power Coupling For Modern Applications, Andrew Burman

BioResource and Agricultural Engineering

This project takes two bifilar tesla coils and uses them to find a % efficiency of power transfer as distances between the coils decrease. The reason this experiment is being conducted is to find possible implications for wireless charging of vehicles using similar style coils. This project conducted experiments on 60 Hz, 400 Hz, and 1 kHz frequencies for a small input signal. The general conclusion is that as the frequency increases more power can be transferred and higher efficiency of power transfer is seen. This project also concluded that it could be possible to get higher efficiency at a …

Design Of A Drip Irrigation System For 80 Acres Of Almonds In Arbuckle, California, Alexander E. Marsh

BioResource and Agricultural Engineering

This senior project discusses the detailed steps and calculations involved with the design of a dual line buried drip irrigation system. The system is specifically for an 80 acre orchard of almonds in Arbuckle, California. The new design distribution uniformity of the design in 0.92.

Design And Testing Of An Autonomous Ground Robot For Agricultural Applications, Lukas L. Hannemann

BioResource and Agricultural Engineering

This senior project discusses the design and testing of an autonomous ground robot for agricultural applications such as strawberries. The vehicle will feature a robotic arm that will be programmed to perform various tasks, such as collecting soil and leaf samples of the crop or measuring soil moisture and salinity. Various components were chosen to be implemented on the vehicle due its power requirements and operating environment. Finite Element Analysis testing was done on the frame of the vehicle to ensure the adequacy of the design.

Design, Construction, And Evaluation Of A Gas Forge, Spencer M. Davis

BioResource and Agricultural Engineering

This report covers the design, construction, and evaluation of a propane forge. The purpose for building this propane forge was to replace an old charcoal forge in order to improve upon certain points of performance such as adjustability of heat, portability, and fuel cost by being able to run the forge for any amount of time with an easy on/off control. The design of this forge consisted of a steel pipe body insulated with ceramic fiber blanket, and was heated by a single atmospheric burner.

Crop Selection, Cost Analysis, And Irrigation System Design For The Replanting Of A Nut Orchard, Maximilian Bricker

BioResource and Agricultural Engineering

This report was made to help the landowner of Bricker Farms make decisions regarding the replanting of his orchard. The decisions that need to be made in this process include: which crop to plant, how to plant it, and how to improve the distribution uniformity of irrigation water on the orchard. The report does not give definitive final decisions, but presents viable options that the landowner can utilize when deciding. In addition to the options that are presented, the report offers suggestions to the landowner so that the replanting process is done properly in a timely and economically-friendly manner.

Design, Construction, And Evaluation Of An Almond End-Row Nut Sweeper, Andrew J. Mancini

BioResource and Agricultural Engineering

This senior project discusses the design, construction, and evaluation of an almond end-row nut sweeper. The sweeper attached to the three-point hitch of a John Deere orchard tractor using a Category 2 hitch and was used to sweep nuts back into the orchard after they had been swept into windrows. This system worked by utilizing the tractor hydraulics to power an 18 inch diameter cylinder brush.

Proper field testing of the implement could not be done during the academic year in which this project was constructed since this implement was designed to be used as part of the California almond …

Design Of A Folding V-Scraper With Roller For Orchard Applications, Chase Ulrich

BioResource and Agricultural Engineering

This senior project discusses the design of a folding 15 ft. wide leveler for orchard use. This design utilized a category 2 three-point hitch to connect the implement to a tractor. The folding mechanism uses the tractors hydraulic system to actuate the folding movement using hydraulic cylinders. The blades, when wings in operational position, are rigid with one another after some assembly. When the implement is folded the width is reduced to nine feet.

Design, Construction, And Evaluation Of Off-Road Rock Sliders, Jake M. Freedman

BioResource and Agricultural Engineering

This senior project describes the design, fabrication, and evaluation of off-road rock sliders which can be used with Toyota Tacoma trucks of model year 2005-2012. Rock sliders are a form of trail armor and are a common aftermarket addition to trucks that are often used in off-road conditions. Rock sliders, in their simplest form, consist of a steel beam (either tubular or rectangular) that runs underneath the doors of the vehicle providing protection to the undercarriage, rocker panels, and doors as well as reducing the likelihood of becoming stuck or “high-centered” on the underside of the vehicle. The sliders will …

Design And Build Of An Automated Animal Feed Dispenser, Soroush Sedigh

BioResource and Agricultural Engineering

This senior project discusses the design, construction, and evaluation of automated animal feed dispenser on a small-scale level. The system consists of three main components with various sub-components. Those three components are the outer-casing, the hardware and circuitry, and lastly the code to make sure the hardware operates properly.

System tests have indicated that the feed dispenser is able to provide one week’s worth of feed to the end user with no human interference

Reconstructing The Natural Hydrology Of The San Francisco Bay - Delta Watershed, P. Fox, P.H. Hutton, D.J. Howes, A.J. Draper, L. Sears

BioResource and Agricultural Engineering

We evaluated the impact of landscape changes on the amount of delta outflow reaching San Francisco Bay. The natural landscape was reconstructed and water balances were used to estimate the long-term annual average delta outflow that would have occurred under natural landscape conditions if the climate from 1922 to 2009 were to repeat itself. These outflows are referred to as natural delta outflows and are the first published estimate of natural delta outflow. These natural delta outflows were then compared with current delta outflows for the same climate and existing landscape, including its re-engineered system of reservoirs, canals, aqueducts, and …

Rating Rectangular Farm Delivery Meter Gates For Flow Measurement, Daniel J. Howes, Charles M. Burt

BioResource and Agricultural Engineering

Traditional meter gates for farm delivery flow measurement from an open channel conveyance have traditionally incorporated round canal gates (Armco type) for control. In recent years, some irrigation water agencies (i.e., irrigation districts) have replaced deteriorating round gates with lower-cost rectangular gates that cover round holes. Similar to the situation described in a companion paper, where round gates were examined, there have been no investigations into flow measurement uncertainty using the existing rating tables for these gates. In this study, two commonly used rectangular gate sizes, 0.46 m (18-in.) and 0.61 m (24-in.), were tested under scenarios of various gate …