Bioresource and Agricultural Engineering Commons^™

Controller Area Network (Can) Bus J1939 Data Acquisition Methods And Parameter Accuracy Assessment Using Nebraska Tractor Test Laboratory Data, Samuel E. Marx

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

Electronics have become a standard in agricultural equipment and the trend of “smarter” equipment is on the rise. To have “smarter” equipment, a working knowledge of the accuracy of the data being transmitted throughout that equipment is needed. The controller area network (CAN) bus is the current interface to machine operation data transmitted between electronic control units (ECUs).

Because CAN bus has been around for nearly thirty years, numerous devices have been created for interfacing with the bus. Choosing a device can be a challenge, especially without knowing if there are differences between the logging methods for true data representation. …

Smart V-Belt, Kyle J. Mosier

Open Access Theses

The purpose of this research was to develop a method for detecting premature failure in a v-belt using capacitance and resistance readings. Another goal of the research was to detect tension values on the belt using the same readings. Materials of current belts and possible materials for a prototype belt were tested. Materials were chosen, and prototype belts were built. Pulley system configurations were developed and built. Sections of the belt designs were tested for capacitance and resistance before and after various methods of damage. Capacitance was chosen as the better sensing method. Certain layered belt configurations and sheave configurations …

Methane Production By A Packed-Bed Anaerobic Digester Fed Dairy Barn Flush Water, Sean Richard Thomson

Master's Theses

Packed-bed digesters are an alternative to covered lagoon digesters for methane production and anaerobic treatment of dilute wastewaters such as dairy barn flush water. The physical media of packed-beds retain biofilms, often allowing increased treatment rates. Previous studies have evaluated several types of media for digestion of dilute wastewaters, but cost and media fouling have setback commercial development. A major operational cost has been effluent recirculation pumping.

In the present effort, a novel approach to anaerobic digestion of flush dairy water was developed at pilot-scale: broken walnut shells were used as a low-cost packed-bed medium and effluent recirculation was replaced …

Agricultural Industry Advanced Vehicle Technology: Benchmark Study For Reduction In Petroleum Use, Roger M. Hoy, Rodney Rohrer, Adam Liska, Joe D. Luck, Loren Isom, Deepak R. Keshwani

Adam Liska Papers

Diesel use on farms in the United States has remained relatively constant since 1985, decreasing slightly in 2009, which may be attributed to price increases and the economic recession. During this time, the United States’ harvested area also has remained relatively constant at roughly 300 million acres. In 2010, farm diesel use was 5.4% of the total United States diesel use. Crops accounting for an estimated 65% of United States farm diesel use include corn, soybean, wheat, hay, and alfalfa, respectively, based on harvested crop area and a recent analysis of estimated fuel use by crop. Diesel use in these …

Design And Development Of A Novel Test Method To Measure The Slipper / Swashplate Interface Fluid Film In A Positive Displacement Machine, Natalie A. Spencer

Open Access Theses

Although robust models of fluid film behavior between the slipper / swashplate lubricating interface in positive displacement machines have been developed, measuring this same fluid film thickness to a highly accurate degree inside a relatively unaltered axial piston unit has never been accomplished until now. A test method was created to close this gap in available data by measuring fluid film thickness between the slipper and swashplate in a 130cc axial piston pump. Precise knowledge of the gap height between the slipper and swashplate at various shaft angle locations during operation provides critical insight into machine behavior. The design, validation, …

Vehicle Multi-Pass Rut Volume And Mobility Power Study, William W. Barbour

Pursuit - The Journal of Undergraduate Research at The University of Tennessee

This paper presents the relationship between applied power by a wheeled vehicle to soil and the rutting effects. Specifically, a strong positive relationship was found between cumulative applied power and total rut volume across multiple passes by the vehicle over the same tracks. Field-testing was conducted using a high-mobility multi-purpose wheeled vehicle (HMMWV) and two distinct soil types. Sensors on the vehicle measured torque and angular velocity of each of the four wheels, from which applied power was calculated. A rut profile meter was used to document the shape of the rut after set numbers of passes and this profile …

Modification Of A Draw Bar Type Arena Harrow To Three Point Mounted Type Harrow, Clayton Alan Brown

BioResource and Agricultural Engineering

This senior project will be the design, and construction of a three point hitch to be attached to a draw bar type spike tooth harrow. Currently used by the Cal Poly Rodeo Team to cultivate their arena before performances, and practices.

The attachment will allow the harrow to be pulled in both directions to create different types of soil affects.

Also the fabrications has a minimal budget so the majority of the materials will be scrap material already in position of the rodeo team or donated to the project.

Nuts & Bolts, Volume 2, Issue 2, Lance Todd, Julie Thomson, Louis Leviticus

Friends of the Larsen Tractor Museum

Museum Open House is a Success

The Passing of Museum Volunteer Larry Ehlers

Larsen Museum to Auction Twelve Tractors

Details an Estate Planning and Memorial Designation

Assessment Of Corn Stover Torrefaction For On-Farm Biochar Production, Christina M. Gerometta

Electronic Theses and Dissertations

Torrefaction is a thermochemical pretreatment process that is typically achieved by slowly heating biomass (<50°C/min) within the temperature range of 200 – 300°C under an inert atmosphere. This process yields a storable solid product with enhanced fuel characteristics that are influenced by the ligno-cellulosic composition of the original feedstock and the imposed torrefaction conditions (time and temperature). This study is an assessment of corn stover properties that are relevant for designing an on-farm torrefaction system. The first portion of this study compared the thermal decomposition behaviors of corn stover fractions (leaf, stalk, cob) to the respective ligno-cellulosic composition using thermo-gravimetric analysis. It was found that the thermal decomposition pattern correlates to the structure and ratio of ligno-cellulosic polymers and provides design guidelines for an on-farm torrefaction system capable of handling large quantities of mixed fraction stover. The second part of this study investigated the effects of torrefaction time and temperature on the mass and energy yield of mixed fraction corn stover using a 46.3 L batch style reactor. It was found that longer reaction times and higher temperatures were required to obtain mass and energy yields similar to those found using lab-scale reactors and finely milled samples. Non-uniform torrefaction occurred between fractions due to chemical composition of each fraction and proximity to the heating elements.

Low Cost Flow Sensing For Field Sprayers, Yue Zhang

Theses and Dissertations--Biosystems and Agricultural Engineering

Precisely measuring the flow rate in sprayers is a key technology to precision agriculture. With the development of advanced technologies, the demand for the ability to measure flow rate of individual nozzle has become more important and urgent.

This paper investigates the possibility of developing a low-cost flow rate measurement technique. The technique is based on analyzing the acoustic signal from a microphone placed near the nozzle tip. A comparison between acoustic signal and vibration signal was made to study the relations between them. Then several possible locations of the microphone for measuring flow rate were tested and compared, and …

Computer Simulation Study Of Slipper Lubrication In Hydraulic Machines, Jordyn B. Miller, Monika Ivantysynova

The Summer Undergraduate Research Fellowship (SURF) Symposium

Hydraulic pumps and motors are vital components used in many applications today. Specifically, the axial piston pump is important because it is reliable, relatively compact, and has a high horsepower-to-weight ratio. These features make this type of pump very advantageous in hydraulic systems. Maintaining proper lubrication between surfaces in an axial pump, such as the slipper and swashplate, is imperative in order to have smooth operation of the system and prevent metal-to-metal contact. The aim of this research is to find the optimal slipper design and fluid film thickness to simultaneously maintain a balanced pressure and decrease power loss in …

Design Of A Novel Actuation System For Variable Displacement Gear Machine, Mark W. Mahuren, Andrea Vacca

The Summer Undergraduate Research Fellowship (SURF) Symposium

External spur gear pumps are exceedingly useful components in common hydraulic systems. The main issue with external gear pumps is that all current models are limited to only fixed-displacement. This means that for every revolution of the gears inside the pump, a set amount of fluid will always be displaced. Consequently, external gear pumps are limited in their use because they can only operate at full throttle causing inefficiencies when reduced displacement is needed. The successful procurement of a variable displacement gear pump will allow a more efficient use of hydraulic systems, such as in the displacement controlled systems used …

Crane Shaking Platform Design, Bixing Yan, Andrea Vacca

The Summer Undergraduate Research Fellowship (SURF) Symposium

Most of the control methodology of Mobile hydraulic crane is not as energy efficient as people think or want, and the desire to innovate novel, energy-efficient control strategy is the target of most hydraulic experts. To develop or test the control method under real road and off-road conditions, a platform that could simulate the movement and vibration of the crane truck is desired. To design and build the multi-operation platform, a design process includes brain storming, design selection, FEA (Fundamental Element Analysis), mechanical sizing, hydraulic sizing and Bill of Material is required and preferred. After going through all the steps …

Design, Construction And Evaluation Of A Low Head Hydroelectric Turbine For Canals, Sean Phillip Ellenson

BioResource and Agricultural Engineering

Means of hydroelectric power generation today typically require state or federal funding, massive construction projects and high head differentials with the use of a dam. With thousands of miles of canals and waterways at our disposal, it is necessary to find a cost effective way of generating a substantial amount of power from low-head hydroelectric power sources.

This senior project details research on low-head hydroelectric power generation, along with the design, construction and evaluation of a twisted Savonius hydroelectric turbine. Sizing optimizations for a twisted Savonius turbine were performed, and the hydroelectric power generation unit was constructed, including a housing …

Residential Fire Sprinkler Design For The Phi Kappa Psi Fraternity House, Nolan Frost

BioResource and Agricultural Engineering

This senior project discusses the design of a residential fire sprinkler system for a local fraternity house. The design follows NFPA 13D code, and contains design calculations, design drawings, material specifications, and cost analysis. The design was completed with the intention of being used for the installation of a fire sprinkler system in the house.

Testing The Fuel Efficiency Of Tractors With Continuously Variable And Standard Geared Transmissions, Christopher N. Howard, Michael F. Kocher, Roger M. Hoy, Erin E. Blankenship

Department of Agricultural and Biological Systems Engineering: Faculty Publications

A John Deere 8295R IVT tractor with a continuously variable transmission (CVT) and a John Deere 8295R PowerShift (PST) tractor with a standard geared transmission (GT) were tested for fuel consumption at three different travel speeds with six different load levels applied per speed. The JD 8295R PST tractor was tested both at full throttle (FT) and shifted up two gears and throttled back (SUTB) to achieve the same travel speed as at full throttle. For each travel speed with each transmission mode, fuel consumption was determined to be linearly related to drawbar power. Linear regression analyses were performed, and …

Design And Construction Of A Solar Operated Gate, Jacob Gardener

BioResource and Agricultural Engineering

This senior project discusses the design and construction of a solar operated gate. A solar panel is used to charge a battery, and then an inverter is used to run a garage door opener off the battery. The garage door opener operates a short lever arm which is connected to a longer lever arm which is connected to the gate. Each component and mounting mechanisms were designed and built to effectively provide the gate opening function. The finished product operates well, the gate opens in about 8 seconds after the button is pressed on the remote controller or wall mount …

History Of The Biological Systems Engineering Program In Nebraska, University Of Nebraska-Lincoln, William E. Splinter

Department of Agricultural and Biological Systems Engineering: Faculty Publications

The Farm Machinery/Agricultural Engineering/Biological Systems Engineering program current and former faculty members at the University of Nebraska, as demonstrated here, has made a statewide, national, and worldwide impact on the efficient production of food. The quality of this recognition is evidenced best by peer professionals through recognized ASABE awards received by Nebraska alumni or professors. Since its inception in 1909 and until 2010, there have been 10 national presidents, 19 gold medal recipients and 33 named national award recipients. Currently there are 31 ASABE Fellows and two members of the National Academy of Engineering. This national recognition comes as a …

Design Of A Smart System For Monitoring Concrete Curing And Structural Health, William Quinn

Theses

Structural Health Monitoring (SHM) is a rapidly growing sector of the construction industry. Automated monitoring methods arc mainly limited to global monitoring and the application of local monitoring methods has not gained widespread application due to the fact that currently technology requires that the systems are wired to data acquisition devices. This thesis presents a fully embeddable wireless sensor node for the local monitoring of structural concrete. It presents the first reported wireless embedded system implementation of the electromechanical impedance method using both resonant and antiresonant sensors for this purpose.

The first section of this thesis examines the feasibility of …

Guidance Directrix Generation Using Laser Sensors, Santosh Pitla, Joe D. Luck, Scott A. Shearer

Department of Agricultural and Biological Systems Engineering: Presentations and White Papers

A sensor array consisting of two laser sensors was utilized to determine the guidance directrix (offset distance-d, heading angle-ø) that are required as reference inputs for an automated guidance system. The sensor array was evaluated in both laboratory and field conditions. Under laboratory conditions the sensor array replicated the physical profile of the target surface with a 4% error in determining the heading angle. Field tests were conducted in two types of crops; corn and alfalfa. The sensor array identified the cut-crop edge profile ahead of the tractor and replicated distinct shapes of the cut-crop edge. RMSE values in determining …

Carbon Conversion During Bubbling Fluidized Bed Gasification Of Biomass, Kevin Timmer

Faculty Work Comprehensive List

Gasification is one means of transforming biomass so that it can be more easily utilized as a renewable source of thermal energy, transportation fuel, and chemicals. Under typical gasification conditions it is not uncommon that a portion of the carbon entering with the biomass leaves the reactor unconverted as char. Understanding and improving carbon conversion during biomass gasification in an atmospheric bubbling fluidized bed reactor is the focus of this study.

To better understand the intricacies of biomass gasification a carbon conversion analytic methodology was developed. The methodology is based on a mass balance of the fixed carbon entering and …

Economic Evaluation Of Integrating Biodiesel Production With A Dry Mill Ethanol Plant, Steven Bly

The Journal of Undergraduate Research

Biodiesei is produced by adding methyl ester products to diesel fuel. Base catalyzed transesterification of oil with methanol is the primary process used today. Current dry mill ethanol production facilities allow the com oil to pass through the process where it becomes part of the dried distiller's grain with solubles (DDGS), a lower valued feed co-product. This study evaluated the economic feasibility of integrating a biodiesel production facility with existing and/or new dry mill ethanol plants. The following methods for com oil separation were considered; hexane extraction of com oil from the dried distiller's grain stream, initial germ separation and …

Evaluation Of A Mechanical System For Reconstructing Soil On Surface Mined Land, John P. Fulton, Larry G. Wells

Biosystems and Agricultural Engineering Faculty Publications

The existence of excessive soil compaction has hindered the surface mining industry from returning land to pre−mining productivity after reclamation, especially on prime farmland soils. Heavy earthmoving equipment used during reclamation tends to generate root−limiting bulk densities that adversely affect plant growth thereby decreasing yields. Therefore, the purpose of this study was to evaluate a mechanism, called the ‘Soil Regenerator,’ which reconstructs soil media at minimum bulk density during surface mine reclamation. The prototype soil forming mechanism was mounted on the front of a conventional bulldozer. Soil was placed in long narrow windrows by a scraper or bulldozer. As the …

Effect Of Moisture And Loading Orientation On The Mechanical Properties Of Sorghum And Millet, E. L. Lazaro

Tanzania Journal of Engineering and Technology (TJET)

Uniaxial compression properties of sorghum and millet grain at different moisture contents (12–25% dry basis) and at different kernel orientation were investigated. These included: modulus of deformability, maximum compressive force, deformation and toughness at grain break point. Individual grain kernels of two varieties of sorghum, (Dionje and Jumbo) and one variety of pearl millet, (IM) at 12, 15, 20, and 25% moisture content dry basis (mc.db), were quasi-statically loaded using a J.J.universal tensile testing machine to their breaking point. The modulus of deformability, maximum compressive force required to initiate grain rupture and the grain toughness (energy absorbed at break point …

A Mechanical System For Soil Reconstruction, John Patrick Fulton, Larry G. Wells, Timothy D. Smith

Biosystems and Agricultural Engineering Faculty Publications

One of the most perplexing problems associated with reclaiming surface–mined lands is excessive compaction of soil due to the heavy earthmoving equipment used during the reclamation process. Over the years, some innovative material handling schemes have been devised to limit vehicle traffic during reclamation on reconstructed soil. However, final grading operations can often create root–limiting bulk densities, which affect plant growth and yield. The purpose of this article is to describe a mechanism designed at the University of Kentucky whereby mine soil can be reconstructed without introducing compaction caused by surface traffic in order for the soil to sustain desirable …

Investigation Of Forces Acting On Plain Discs, S. M. Mpanduji

Tanzania Journal of Engineering and Technology (TJET)

An investigation was carried out to study the mutually perpendicular forces generated by rotating and non-rotating plain discs similar to those used in disc ploughs. Experiments were conducted in a soil bin containing sand loam soil (Ryton sand) where forces were measured while changing disc rake and sweep angles. The results showed that draught forces were higher for non-rotating discs, while vertical and lateral forces were lower compared to rotating discs. Rotating discs were found to be suitable for counteracting high side forces because of less draught and higher lateral forces. The recommended optimum angles are between 8°–12° for disc …

Comparison Of Repair Costs Of Two Wheel Drive Tractors Under Tanzania Conditions, S. M. Mpanduji

Tanzania Journal of Engineering and Technology (TJET)

The repair costs of 2WD tractors were investigated in order to provide important information, which lacks in the scope of agricultural mechanization in Tanzania. Previously repair cost functions established for tractors in developed countries were used for both theoretical and practical purposes. The findings of this study have revealed that repair costs of tractors vary substantially from one make to another. The prediction functions developed in this study indicated that the magnitudes of repair costs in Tanzania are higher than the repair costs established in Europe and North America. The reason for this could be either due to high cost …

A Reduced–Cost Mechanized System For Handling And Curing Mechanically–Harvested Burley Tobacco, Greg A. Camenisch, Larry G. Wells, Timothy D. Smith, George A. Duncan

Biosystems and Agricultural Engineering Faculty Publications

An experimental system was tested in which mechanically harvested burley tobacco plants placed onto steel slotted receivers were retrieved from a field, transported to a field curing structure, and placed onto the structure for air curing by a single worker. The system consisted of a tractor–towed, trailer mechanism that engaged and hoisted loads of approximately 360 burley plants of approximately 1 Mg mass. Ten slotted steel rails, 3.05 m long, holding 36 notched plants were placed onto parallel wooden beams suspended at a height of 2.13 m by wooden posts set in the ground. Burley tobacco was cured in this …

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna

Tanzania Journal of Engineering and Technology (TJET)

Vibration is one of the techniques employed in the determination of dynamic properties of fruits and vegetables. It entails generation of a mechanical or acoustic vibrational signal which is propagated through the flesh of the agricultural material. A transducer is either attached or held close to the specimen to monitor the propagation of the signal through the specimen. The manner in which the signal is transmitted through the material is analyzed, and the dynamic properties of the specimen which relate to its firmness or its internal being are derived. The technique has been around for the past 30 years or …

Retention Of Gasification-Combustion Products By Corn, S. W. Sizemore, Otto J. Loewer, Joseph L. Taraba, I. J. Ross, G. M. White

Biosystems and Agricultural Engineering Faculty Publications

Shelled corn was dried in layers of 5.1 cm (2 in.) 10.2 cm (4 in.), and 15.2 cm (6 in.) using air heated with the exhaust from a corn-cob fueled gasification-combustion updraft furnace. The drying air entering and leaving the grain layers was sampled for particulate content to determine the percentage of total particulates trapped by the grain during drying. It was determined that an average of 25% of the total particulates in the drying air were retained by the grain. The large majority of those particulates retained were found in the bottom 5.1 cm (2 in.) of the grain …