Bioresource and Agricultural Engineering Commons^™

Mechanical Fractionation Of Wheat Middlings For Application In Pyrolysis And Animal Feed, Okwudili I. Obiakor

Dissertations, Master's Theses and Master's Reports

Wheat middlings are grain byproducts that are underused for bioenergy production despite having a high lignocellulose content. Its use as a feedstock for catalytic pyrolysis depends on effective and sustainable fractionation to enhance efficiency and product yield. This study tested mechanical pre-fractionation (sieving and air classification) to reduce ash content of certain fractions to < 1% for catalytic pyrolysis and enrich nutrient levels of other fractions for feed applications. Wheat middlings were separated into 11 fractions using screen sizes from 106 µm to 1651 µm, and the composition of each fraction was characterized (ash, protein, structural carbohydrates, lignin, starch, and simple sugars). For cyclone separation, a full factorial design was used to study the effect of air velocity (15,18, 20 m/s) and feed rate (33, 35, 38 kg/h) on the amount of material collected in the underflow and overflow, and the composition of these fractions was characterized. Sieving showed a pronounced segregation of ash content, from 4.5% to 6.5% in wheat middlings fractions, with 5.7% being the lowest for coarse fractions which has higher lignocellulose content, and 4.5% in the fine fraction (150-212 µm). The same defined enrichment was observed in all nutrients except for protein. Starch enrichment zone were defined in the fine fractions (212 µm and below), for structural carbohydrates and lignin in the coarse fractions (600 µm and above), and for ash in coarse fractions (1180-1651 µm). In contrast, protein content was not significantly different between various fractions (p value=0.787). The fiber rich fraction (> 600 µm), suitable for pyrolysis, which have a composite ash value of 6.0% can be sorted and mixed with intermediate fractions to reduce ash to 5.3% and the remaining fractions rich in digestible nutrients used for animal feed formulation. Compared to sieving, cyclone separations did not …

Cultivation Of Botryococcus Braunii For The Production Of Hydrocarbons Suitable For Fuel Use, Bryan C. Carroll

All Theses

Energy security, rural poverty, and climate change are pressing issues of our time. Biofuels provide a solution to these issues, with a focus on sustainable aviation fuel, SAF, due to compatibility with aircraft infrastructure and energy density. This research aims to review and produce knowledge about a specific microalga, Botryococcus braunii, for its potential for SAF. First a literature review on the process was conducted followed by an experimental study on the impact of aqueous media and inorganic carbon its growth and hydrocarbon content. The literature review found the process consists of cultivation followed by lipid extraction or hydrothermal …

Kinetic Growth Rate Analysis Of Coelastrella Sp. In Aquaculture Wastewater., Rob Skarvan

Master of Engineering Theses

The demand for sustainable food and energy production continues to rapidly rise. Utilizing aquaculture wastewater as microalgae growth medium is a potential opportunity for nutrient recycling and industrial symbiosis, but more research is required to understand how best to design and scale-up a dual-purpose facility. This study investigates the growth of Coelastrella sp. in aquaculture wastewater compared to industry-standard growth medium BG-11 and modified tap water as controls. Though cell size and pigment density varied throughout media, aquaculture wastewater performed very comparably to BG-11 as a microalgae culture broth.

The Monod equation can model Coelastrella sp. growth based …

Enhancing The Mechanical Properties Of Sla 3d-Printed Bio-Resin From Linseed Oil Using Cellulose And Lignin Biopolymers, Chukwunonso A. Ikedionu

College of Graduate Studies: Theses & Dissertations

Abstract

This research explores the development of bio resin from linseed oil by the process of epoxidation and acrylation to produce acrylated epoxidized linseed oil (AELO). Lignin and cellulose biopolymers were added as reinforcement at varying weight fractions of 1 wt.%, 2.5 wt.%, and 5 wt.%, and their mechanical performance was compared against pure AELO. The formulations were printed using an Elegoo SLA 3D printer to create standardized test specimens like tensile bars, compression cylinders, and hardness blocks, which were all prepared according to the ASTM testing standard.

The results indicate that reinforcement effects depend on both filler type and …

Valorizing Municipal Solid Waste For Sustainable Aviation Fuel And Polyhydroxyalkanoate Bioplastics: Pyrolysis And Microbial Pathways, Emon Das

Theses and Dissertations--Biosystems and Agricultural Engineering

The escalating global burden of municipal solid waste (MSW), projected to reach 3.88 billion tons annually by 2050, calls for innovative valorization strategies to mitigate environmental impacts and promote a circular bioeconomy. This thesis investigates the conversion of MSW into two high-value products: sustainable aviation fuel (SAF) and polyhydroxyalkanoate (PHA) bioplastics. Chapter one presents comprehensive physicochemical characterization and pyrolysis-GC/MS analysis of MSW feedstocks. The physicochemical results reveal that densification enhances handling and storage properties, while pyrolysis-GC/MS analysis indicates that plastic-rich MSW streams produce bio-oils with favorable hydrocarbon profiles suitable for SAF production, potentially contributing to decarbonization efforts in the aviation …

Kinetics Model Of Cananga (Cananga Odorata) Fresh Flower Extraction Using Microwave Hydrodistillation Method, Darnengsih Darnengsih, Hikmatun Ni’Mah, Mahfud Mahfud, Ayu Chandra Kartika Fitri

Makara Journal of Science

Recent studies have focused on improving essential oil extraction methods by incorporating advanced technologies, such as microwave-assisted hydrodistillation (MHD). Despite these advancements, further research is necessary to fully understand how different kinetic models influence extraction efficiency. This study evaluates several kinetic models for extracting essential oil from fresh Cananga flowers using MHD, examining how varying microwave power affects extraction rates and correlates with kinetic model parameters. The extraction process involved introducing 200 grams of fresh Cananga flowers in 400 mL of distilled water and subjecting the mixture to microwave power levels of 200 W, 400 W, and 600 W. The …

Integrating Sustainability And Food Safety Through Quantitative Microbial Risk Assessment And Life Cycle Assessment Of Low-Moisture Foods, Jessica Bain

Graduate Theses and Dissertations

Food safety and sustainability are critical concerns in the food industry. However, these areas are often evaluated separately, leading to an incomplete understanding of the overall impact of food production on human health. This dissertation aims to integrate food safety with sustainability to provide a comprehensive assessment of the impact of low-moisture foods on human health, using the almond processing supply chain as a case study.

In addition to conducting life cycle assessments (LCA) of almond processing, wheat flour production, and dried apple processing, this dissertation aims to create a framework to bridge the gap between sustainability and food safety. …

Isolation And Upgrading Of Lignin From Agricultural Sources Using Phase Equilibria, Bronson Lynn

All Dissertations

In the emerging bioeconomy, agricultural residues from our nationwide crop harvests are positioned to be a cornerstone of renewable and sustainable fuels, chemicals, and materials. However, to be economically viable, the basic constituents of this plant matter must be separated and funneled to the appropriate application to maximize value and overall usability.

This work focuses on the component that has, to this point, been largely left behind: lignin. Although it is the most abundant aromatic biopolymer on the planet, making up 15-40% of grasses, hardwoods, and softwoods, the processing involved to isolate usable lignins is too complex and expensive to …

Investigating The Impact Of Secondary Activation Time On The Adsorption Properties Of Activated Biochar For Arsenic Removal From Wastewater, Achyuth Bharadwaj Rayarao

Graduate Theses and Dissertations (2019 - present)

Biochar, a naturally occurring and renewable carbon material, becomes porous through activation. Activated biochar is an ideal candidate for use as an adsorbent. The objective of this study is to investigate whether activated biochar derived from Colorado soft pine serves as a better adsorbent and demonstrates enhanced adsorption capabilities after undergoing secondary physical activation at various activation times. The effect of secondary action time on physical adsorption properties drawn from the analysis of isotherm plots, surface areas and pore size patterns were examined by using a physisorption analyzer. Chemical structures were identified using both ultimate and proximate analyses, while porosity …

An Assessment Of Methane Cracking Technologies For Hydrogen Production And Reduction Of Greenhouse Gases, Alisa E. Pjetrovic

2024 Spring Honors Capstone Projects - Archive

Methane reformation and methane pyrolysis involve separating, or cracking, the components of methane, leading to the production of hydrogen gas, and in the case of pyrolysis, solid carbon. Because methane is known as a leading cause of climate change, these technologies are gaining attention as the global community moves to address methane as a greenhouse gas. This study aims to assess, through a systematic literature review, the current state-of-the-art methane cracking technologies based on seven technology criteria: hydrogen production capability, environmental impact, value of carbon produced, reaction stability, operating temperature requirements, energy requirements, and Technology Readiness Level (TRL). This study …

Modernization Of Water Flow Measurement In Open Irrigation Systems Using The Slope-Area Method, R.M. Aliev, Djalilov Anvar

Chemical Technology, Control and Management

This article describes two methods for determining water flow in open irrigation systems: “speed - area” and “slope - area”. The authors considered the problem of its modernization using the existing method for determining water flow “slope - area” in open irrigation systems. The essence of the issue is the remote transfer of parameters necessary for calculating water flow in open irrigation systems and improving the means of their processing. In scientific studies conducted by the authors, the required hydraulic parameters were studied using the “slope - area” and “speed - area” water flow methods. Based on experimentally obtained data, …

Valorization Of Bourbon Distilling Waste Using Thermal Conversion Processes For Nutrient-Rich Food Products, Tosin Olayemi Olanrewaju

Theses and Dissertations--Biosystems and Agricultural Engineering

The Commonwealth of Kentucky accounts for over 95% of global bourbon production. A primary byproduct of bourbon production is stillage, which has a very high moisture content (91–94%) and high biochemical oxygen demand, making it challenging to manage. The recent expansion of the bourbon industry has heightened environmental concerns regarding the best methods to handle this byproduct. Dewatering and drying of stillage produce distillers' spent grains (DSG-B), which are rich in dietary fiber and protein and could serve as an excellent source of functional fiber in human nutrition.

This study examined the approach for dewatering, drying, inclusion of DSG-B as …

Reducing Food Scarcity: The Benefits Of Urban Farming, S.A. Claudell, Emilio Mejia

Journal of Nonprofit Innovation

Urban farming can enhance the lives of communities and help reduce food scarcity. This paper presents a conceptual prototype of an efficient urban farming community that can be scaled for a single apartment building or an entire community across all global geoeconomics regions, including densely populated cities and rural, developing towns and communities. When deployed in coordination with smart crop choices, local farm support, and efficient transportation then the result isn’t just sustainability, but also increasing fresh produce accessibility, optimizing nutritional value, eliminating the use of ‘forever chemicals’, reducing transportation costs, and fostering global environmental benefits.

Imagine Doris, who is …

Characterization Of Lignin And Cellulose Biopolymers Structure – Function Relationships, Zachariah Pittman

All Dissertations

Biomass is vital to ongoing efforts to secure a sustainable future. While many of our efforts focus on finding alternative forms of energy, biomass among them, only biomass has the potential to serve as a sustainable materials feedstock. However, biomass is heterogenous, complicating the upgrading processes needed to manufacture commodity and performance products. For example, plant biomass consists largely of cellulose, a crystalline polysaccharide, and lignin, a highly stable polyaromatic. The specific properties of cellulose and lignin depend greatly on the plant, harvesting conditions, and isolation procedures. Thus, accurate and reliable determination of the fundamental properties of biomass is crucial …

A Process Intensification Approach To Improve Volatile Fatty Acids Production, Extraction, And Valorization, Can Liu

Theses and Dissertations--Biosystems and Agricultural Engineering

Anaerobic digestion (AD) is a widely used biowaste conversion method. Recent studies have explored arrested methanogenesis as an alternative approach to leverage existing AD facilities and produce volatile fatty acids (VFAs) instead of biogas. VFAs have been recognized as precursors for a range of value-added chemicals and bioproducts. Arrested methanogenesis involves inducing acidic fermentation by halting the AD process before methanogenesis. It has been found that higher organic loading and thermophilic conditions enhance VFA accumulation and stabilize the acidic fermentation (AF) system.

Brewer's spent grain (BSG), a significant by-product of the brewing industry, was employed as the feedstock for VFA …

Microalgae Immobilization With Filamentous Fungi: Process Development For Sustainable Food Systems, Suvro Talukdar

Theses and Dissertations--Biosystems and Agricultural Engineering

Demand for sustainable food sources has increased because of the rapid growth of the world's population.  In this study, microalgae cells of Haematococcus pluvialis were immobilized using the edible fungal strain Aspergillus awamori for potential food applications. The study investigated the impact of fungal loading, pellet geometry, and initial microalgae cell concentration on the immobilization performance and product characteristics. It was found that higher fungal loading and larger fungal pellets contributed to increased immobilization performance while increased initial microalgae concentration inhibited the process. Larger fungal pellets had decreased biomass density, which led to decreased surface concentration of immobilized microalgae but …

Sustainable Material For Urea Delivery Based On Chitosan Cross-Linked By Glutaraldehyde Saturated Toluene: Characterization And Determination Of The Release Rate Mathematical Model, Jayanudin Jayanudin, Retno S. D. Lestari, Indar Kustiningsih, Dandi Irawanto, Rozak Rozak, Reyonaldo L. A. Wardana, Fakhri Muhammad

Karbala International Journal of Modern Science

The aims of this study were to characterize the urea-loaded chitosan microspheres and determine the release kinetic constants and diffusion coefficients. An emulsion cross-linking method was used to prepare the urea-loaded chitosan microspheres. Urea was dissolved in a solution of chitosan then put into vegetable oil and stirred to form an emulsion. Glutaraldehyde saturated toluene (GST) was added into the emulsion dropwise while continuously stirring for the solidification process. Chitosan microspheres filled with urea were washed, dried, and then analyzed. Characterization of the urea-loaded chitosan microspheres was conducted using a scanning electron microscope (SEM), Raman spectroscopy, X-ray diffraction, and particle …

Biochar Preparation, Investigation Of Properties And Application As A Low-Cost Adsorbent – A Review, A Kh Aripov, S M. Turabdzhanov, Sh Komilova, O Sh Qodirov, G S. Rakhimova, T V. Darabkova, Zh Aimenova, L S. Rakhimova

Technical science and innovation

An overview of current developments in biochar application in water and wastewater treatment is given in this article, along with a brief explanation of the sorption mechanisms for removing contaminants and the techniques for biochar preparation. In order to encourage the continued use of biochar in effective water and wastewater treatment, future research directions and environmental concerns about biochar are also presented.

Increase The Nutritional Value Of Pasta With Grains And Pulses, D D. Mirkhodjaeva, E Sh Sanaev

Technical science and innovation

The main goal of this study is to develop a paste formulation containing a mixture of ginger, lemon and mint powder, as well as a combination of legumes and cereals with high nutritional value. This will expand the range of pasta. The task of achieving high quality and economic efficiency is solved by improving a number of technological processes and applying innovative methods. The effectiveness of using innovative methods of freeze-drying and microwave drying is shown in comparison with the process of drying instant pasta by frying them in vegetable oil.

Understanding The Interfacial Processes Of Reactive Nanobubbles Toward Agricultural Applications, Xiaonan Shi

Dissertations

There is a growing interest in nanobubble (NB) technology because of its diverse applications (e.g., detergent-free cleaning, water aeration, ultra-sound imaging and intracellular drug delivery, and mineral processing). NBs have a higher efficiency of mass transfer compared to bulk scale bubbles due to the high specific surface areas. The high specific surface also facilitates physical adsorption and chemical reactions in the gas liquid interface. Furthermore, the collapse of NBs creates shock waves and the formation of hydroxyl radicals (OH).

However, it remains elusive why or how NBs are stabilized in water and particularly, the states of internal pressures of NBs …

Determination Of The Heating Time Constant For Root Crops, Z K. Ergasheva, Beraat Ozcelik

Technical science and innovation

Convective drying refers to one of the energy-intensive processes used in chemical, woodworking, food and other industries. Therefore, in modern conditions, when there is a growing shortage and an increase in energy tariffs, it is important to develop and apply new effective methods of drying wet materials in industrial production, create high-performance drying equipment, improve the operation of existing dryers, which will contribute to the rational use of natural resources, reduce the cost of finished products and increase the competitiveness of production. Root crops are plants in which nutrients are concentrated in tubers or roots. Jerusalem artichoke refers to sugar-containing …

Lignin Valorization Via Reductive Depolymerization Using Promoted Nickel Catalysts And Sub- And Supercritical Methanol, Julia Parker

Theses and Dissertations--Biosystems and Agricultural Engineering

While lignin has been regarded as the most promising renewable feedstock for the sustainable manufacture of aromatic compounds, lignin valorization is necessary to improve the economic viability of biorefineries. Reductive catalytic fractionation (RCF), which combines delignification and lignin depolymerization into a single stage while maintaining the structure and integrity of the cellulose component, has evolved as an effective method for processing biomass. The ability of Cu and Fe to promote the performance of a 20% Ni/alumina catalyst when converting native lignin to alkylphenols by RCF in sub- and supercritical methanol was tested. The effectiveness of lignin extraction as measured by …

Recovering And Upgrading Kraft Lignin For Application In Flexible Polyurethane Foam, Peng Quan

Dissertations, Master's Theses and Master's Reports

Lignin is the second abundant natural polymer and has been highlighted as a potential substitute for fossil-based raw materials. However, the inherent molecular heterogeneity and the complex recovery processes result in the challenge of controlling the molecular properties and value-added applications of lignin in large scale. To address those issues, a novel acid-liquefaction process was developed in this study to recover Kraft lignin with improved molecular homogeneity directly from black liquor.

In the first study, the liquefaction parameters were screened based on yield and molecular weight properties of the recovered lignin. Then, the recovered lignin samples were used to replace …

Greenhouse Tomatoes: Process Simulation, Juan Gabriel Marin Jr.

Graduate Theses and Dissertations

Growing population demand and challenges brought on by climate change have spurred the need for more resilient fruit and vegetable supply chains. One agricultural technology of significant interest is the use of greenhouses for food production. Greenhouses create a stable and adaptable environment for crops such as tomatoes to grow year-round. Fresh tomatoes are the second most consumed vegetable per capita in U.S. diets, currently averaging 20.7 pounds. The growing consumption of fresh tomatoes has been the result of increasing cultural diversity in the United States.

To meet the growing demand, Venlo-type greenhouses have been frequently used by growers. It …

Methane Emission Treatment And Potential Upcycling Using Methylomicrobium Alcaliphilum, Jace Parkinson

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

Anthropogenic methane emissions are harmful to the environment and can be difficult to treat. Use of M. alcaliphilum for bioremediation of methane looks to be one of the most promising methods of reducing the negative environmental impacts of methane emissions while simultaneously providing an economic incentive. Successful bioreactor design for M. alcaliphilum based methane treatment requires biokinetic constants and microbial growth information. Methods were established for determining biokinetic constants, including growth rate, biomass yield, specific methane consumption rate, and a correlation between methane oxidation and carbon dioxide production for M. alcaliphilum. Values determined for these constants were used to …

Degumming Of Hemp Fibers Using Combined Microwave Energy And Deep Eutectic Solvent, Bulbul Ahmed

LSU Master's Theses

Hemp is considered as one of the sustainable agricultural fiber materials. Degumming or surface modification of hemp bast is needed to produce single fibers for ensuing textile and industrial applications. The traditional degumming process necessitates a high amount of alkali, which causes detrimental environmental pollution. This study offers a new method to degum hemp fibers with reduced use of harmful alkali and precious water resources. In this work, hemp bast fibers were degummed by using combined microwave energy and deep eutectic solvent (DES). The properties of hemp fibers manufactured by this method were investigated and compared with the traditional alkali …

Exploration Of The Sludge Biodiesel Pathway, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Wastewater sludge is an overlooked source of fat, oil, and grease (FOG) that could be converted into biodiesel. The United States produces about 8 million tons of sludge per year. The disposal cost for this amount of sludge is about 2 billion US dollars. The widespread availability and low cost of sludge compared to other biodiesel raw materials make it an economical choice for a renewable fuel. Using sludge as a raw material can produce 25 to 30 mg per gram of fatty acid methyl ester (FAME); the main component of biodiesel. Sludge biodiesel has the potential of transforming a …

Extraction Of Micro- And Nano-Plastic Particles From Water Using Hydrophobic Natural Deep Eutectic Solvents, Jameson R. Hunter

Theses and Dissertations--Biosystems and Agricultural Engineering

The production of plastic and the amount of waste plastic that enters the environment increases every year. Synthetic polymers will gradually break down into particles on the micro- and nano-scale. The micro- and nano-plastics pose a significant ecological harm by transporting toxic chemicals and causing inflammation and cellular damage when ingested. Two common plastics are polyethylene terephthalate (PET) and Polystyrene (PS), and a newer bioplastic polylactic acid (PLA) that has become a popular alternative. Deep eutectic solvents are a recently discovered solvent composed of a hydrogen bond donor and hydrogen bond acceptor and have been proposed as a cheaper alternative …

Biomass-Derived Electrode Materials And Sustainable Processes For Supercapacitors, Katelyn M. Shell

Theses and Dissertations

Biomass is one of the most abundant natural resources and has been used as a source of energy for thousands of years. Biomass as a precursor for energy storage materials is still relatively novel and faces several obstacles before becoming commonly used in today’s electrical devices. Currently, energy storage devices, such as batteries, capacitors, and supercapacitors, utilize petroleum-derived graphitic carbons for anodes, generating a need for more sustainable materials. Biomass, as a carbon-rich source for electrode materials, presents a viable and economically feasible alternative due to the prevalent lignocellulosic compounds: lignin, cellulose, and hemicellulose. Preliminary studies on the solid residues …

Valorization Of Xylan In Agroforestry Waste Streams, Harrison Appiah

Graduate Theses, Dissertations, and Problem Reports (ETD)

Valorization of Xylan in Agroforestry Waste Streams.

Harrison Appiah

Microwave-assisted deep eutectic solvent and gamma-valerolactone metallic chloride catalyzed conversion of xylan to furfural were investigated using a 2x3 factorial experimental design at two levels of percent microwave power, reaction time, and catalyst concentration. The levels of each factor studied were (20%, 60% microwave power, 2, 4 minutes, and 10, 20mg) respectively. The effect of three metallic chloride catalysts (LiCl, FeCl3.6H20, CuCl2) on the conversion of xylan to furfural was also investigated. The gamma-valerolactone-ferric chloride sent system exhibited the highest mean yield of furfural (56.50%). The next highest furfural yield of …