Molecular, Cellular, and Tissue Engineering Commons^™

Curing Duration Optimization To Reduce Shrinkage Cracking In One-Part Alkali-Activated Slag Concrete, A. Sadrmomtazi, H. Zanganeh

Journal of Sustainable Construction Materials and Technologies

The consequences of inadequate curing on one-part alkali-activated slag concrete (O-AAS) performance relative to ordinary Portland cement concrete (OPCC) have been investigated in this research. Prior to exposure to unsaturated conditions, samples underwent initial moist curing for durations ranging from 24 hours to one year. The testing program included compressive strength evaluation, chloride ion transport analysis, and measurement of free and restrained shrinkage. In addition, cylindrical cores were extracted from concrete columns to assess internal strength and chloride penetration resistance. Under unsaturated exposure, O-AAS exhibited a strength-aging phenomenon, with up to a 37% decrease in compressive strength over 360 days, …

Laboratory Investigation And Numerical Modelling Effect Of Carbon Nanotubes On Hot Mix Asphalt Permanent Displacement, Sepehr Saedi, Auwal Usman Nadada

Journal of Sustainable Construction Materials and Technologies

One of the primary causes of asphalt pavement deterioration is rutting; in contrast, one of the most effective methods to address this type of damage is the use of additives and quality evaluation during the design stages. In this research, laboratory testing and modeling using Abaqus software were employed to validate the laboratory results and predict and assess the potential for rutting. Carbon nanotubes (CNTs) were selected as an additive due to their exceptional mechanical properties and molecular interactions with bitumen. These nanotubes were used to modify the bitumen for the preparation of laboratory samples. The laboratory results from the …

Influence Of Early Microwave Curing On Performance Of Slag-Based Geopolymer Mortars, Ahmet Taşdemı̇R, Abdulkadir Çevı̇K

Journal of Sustainable Construction Materials and Technologies

In this article, an experimental study was conducted to examine the effect of curing time and microwave power on the compressive strength of early microwave-cured slag based geopolymers. Geopolymers have the potential to serve as an environmentally friendly substitute for cement-based building materials, and the use of microwave curing to geopolymers holds the promise of substantial strength improvement. Different microwave curing energies (300 - 800 Watts) were utilized at varying durations (10 - 60 minutes) on demoulded mortar specimens after one day. After that, compressive strength tests were conducted on both the cured and uncured specimens at three different ages: …

Use Of Alaçatı Stone Aggregate In Conventional And Self-Consolidating Concretes, Tahir Kemal Erdem

Journal of Sustainable Construction Materials and Technologies

Alaçatı stone or Alapietra stone is widely used mostly for building cladding. However, its production and use in the construction sites generate high amounts of waste (debris), causing environmental pollution in Çeşme which is a touristic district. This study investigated the reuse of Alaçatı stone as lightweight aggregate (LWA) in both conventional and self-consolidating concrete (SCC) mixtures. The concretes were prepared to have three different water-to-cement ratios (w/c), which were 0.38, 0.42 and 0.48. For each w/c, a conventional concrete mixture and two SCC mixtures with 60 or 70 cm slump flow were produced by varying the superplasticizer SP content. …

A Decision Support Model For Building Material And Component Reuse In The Context Of Circular Buildings, Havva Aksel

Journal of Sustainable Construction Materials and Technologies

Construction activities cause significant environmental impacts such as waste generation, pollution, resource consumption, and land use, which are expected to increase with global construction demands. To mitigate these environmental problems, the circular building occurs as an emerging concept depending on in the circular economy, which aims to minimize waste and redefine the “end-of-life” concept by reducing, reusing, recycling, and recovering materials. The reuse of building materials and components (BMCs) from existing structures represents a crucial strategy for achieving circularity in the built environment. Within this framework, design plays a key role. However, designing with reclaimed BMCs remains complex due to …

Optimization Of Research Pipeline To Characterize The Effects Of Atp-Sensitive Potassium Channels Mutations On Native Skeletal Muscle Fibers And Evaluate Potential Drug Therapy, Yuezhou Chen

McKelvey School of Engineering Graduate Student Theses & Dissertations

The ATP-sensitive potassium (KATP) channel is a critical metabolic sensor in skeletal muscle, yet its definitive molecular composition and functional roles remain contested. In this study, I conclusively demonstrate that the Kir6.2/SUR2 complex forms sarcolemmal KATP channel in mouse fast-twitch muscle. Genetic knock-out (KO) of Kir6.2 (Kcnj11−/−) or SUR2 (Abcc9−/−) resulted in a similar phenotype with increased fatigue resistance and a pathological rise in unstimulated resting tension at high-frequency stimulation. In contrast, SUR1 (Abcc8−/−) KO was ineffective. Furthermore, a CRISPR/Cas9 knock-in mouse model of a human SUR2A truncation variant (KCGV/KCGV) recapitulated the abnormal force accumulation, demonstrating that even loss-of-function of …

Functional Characterization Of Abcc8 Mutations Potentially Linked To The Transition From Hyperinsulinemic Hypoglycemia To Diabetes, Hao Zhang

McKelvey School of Engineering Graduate Student Theses & Dissertations

ATP-sensitive potassium (KATP) channels, composed of the SUR1 and Kir6.2 subunits encoded by the ABCC8 and KCNJ11 genes, are critical regulators of membrane excitability and insulin secretion in pancreatic β-cells. Gain-of-function (GOF) mutations in these genes cause neonatal diabetes mellitus through impaired insulin secretion and persistent hyperglycemia, whereas loss-of-function (LOF) mutations lead to congenital hyperinsulinism (CHI) with hypoglycemia due to β-cell hyperexcitability. I have addressed a paradoxical form of maturity-onset diabetes of the young (MODY) arising from KATP mutations, in which patients transition from CHI to glucose intolerance later in life. My experiments indicate that many KATP mutations associated with …

2d-Nanosilicate Carriers For Sustained Delivery Of Vaccine Components, Chih Yun Liu

McKelvey School of Engineering Graduate Student Theses & Dissertations

Laponite® 2D Nanosilicates (NS) are disc-shaped platelets (~30 nm diameter, ~1 nm thick) with positively charged edges and negatively charged faces, capable of loading proteins, drugs, and nucleic acids via electrostatic interactions to form a house-of-cards gel that sequesters cargo. Here, we evaluated NS for sustained delivery of antigens and Toll-like receptor (TLR) agonists to extend germinal center duration and enhance antibody quality. The model antigen ovalbumin (OVA) was adsorbed onto NS at acidic pH in a ~1:1 ratio, with partial unfolding that remained stable at physiological pH. NS-OVA complexes were efficiently internalized by dendritic cells, with uptake driven primarily …

Durability Of Alkali-Activated Concretes Under 5% Sulfuric Acid Environment, Celal Karabaş, Anıl Niş

Journal of Sustainable Construction Materials and Technologies

The investigation focused on the resistance to 5% sulfuric acid degradation of the alkali-activated concretes (AAC). The AAC was manufactured using a blended binder of 50% slag and 50% F-type fly ash. The AAC was activated using a blend of 14 M sodium hydroxide and sodium silicate, with a hydroxide-to-silicate ratio of 1/2,5. Six AAC were produced against a 5% sulfuric acid environment, varying the binder amounts (400–500–600 kg/m3) and activator-binder (A/B) ratios (0,45–0,55). The chemical resistance of AAC was evaluated by visual appearance, variation in weight and compressive strengths. The findings pointed out that more gypsum and higher weight …

Comprehensive Risk Assessment For Construction Site Managers In Kosovo: A Mixed-Method Approach, Muhamet Ahmeti, Besian Sinani

Journal of Sustainable Construction Materials and Technologies

This study developed and validated a hybrid ISO 31000:2018 Kosovo-compliant risk assessment framework tailored for construction site managers operating within transitional economies. The research employed audits of 20 ISO-certified contractors in Pristina, Kosovo, along with field observations, interviews, and quantitative risk matrices. The findings indicate a critical concentration of risk, with 70% of firms classified as "High" or “Very High” risk. The most prevalent hazards identified were working at height without collective protection, unprotected electrical systems, and manual handling of heavy materials. Regression analysis revealed that firms with a designated safety champion achieved significantly lower risk scores, whereas those with …

Behaviour Of Internally Strengthening Hollow Stainless-Steel Hot-Rolled Circular Columns Filled With Crumb Rubber And Recycled Aggregate Concrete, Wadhah M. Tawfeeq, Mohammed M. Rasheed, Mithaq Kohees, Ahmed W. Al Zandd, Saif Al-Balushi, Hamed Al Abdul Salam

Journal of Sustainable Construction Materials and Technologies

Stainless-steel sections are increasingly being utilised in favour of their higher durability. Simultaneously, the use of recycled materials in concrete is aligned with the global concern to encourage sustainable and environmentally friendly construction. The paper examined the behaviour of stainless-steel columns filled with concrete with crumb rubber (CR) and recycled aggregate (RA). It analysed the effect of different percentages of CR (0, 15, and 30) and RA (0, 15, and 50) on the compressive strength of the concrete and the performance of the columns using stainless-steel hollow sections. 20 specimens were manufactured, 18 of which were cast with concrete containing …

Piezoelectric Concrete: A Smart Material Approach For Energy-Harvesting Structural Technologies, Dianah Mazlan, Vynotdni Rathinasamy, Naveen Kumar, Liu Chunpeng, Elango Elango

Journal of Sustainable Construction Materials and Technologies

The rapid growth of urban infrastructure demands innovative materials that not only support structural performance but also contribute to sustainability through energy harvesting. Piezoelectric concrete, which integrates ceramics, polymers, nanomaterials, and bio-based fillers into cementitious matrices, has emerged as a promising solution. This review systematically explores the fundamentals of piezoelectricity in concrete, highlighting how stress-induced electromechanical coupling enables both energy harvesting and structural health monitoring. The paper critically evaluates major material systems including PZT ceramics, PVDF polymers, hybrid nanocomposites, and emerging bio-based materials, alongside their integration strategies such as embedded and surface-mounted approaches. Applications across pavements, bridges, and smart buildings …

A Novel Microfluidic Device For Preclinical Testing Of Chemotherapeutics, Kaija Saleh Ogan

Master's Theses

This work demonstrates the feasibility of a novel microfluidic tumor model that reproduces physiologically relevant nutrient gradients and endothelium–tumor interactions, validating its potential as a preclinical test platform. Finite element simulations of glutamine diffusion and fluid dynamics aligned with experimental tracer studies, and co-cultures supported directed endothelial migration toward tumor spheroids, confirming the device’s ability to mimic in vivo–like behavior.

Current preclinical models often fail to capture the complexity of the tumor microenvironment (TME), limiting their predictive value for therapeutic testing. Nutrient availability and angiogenic signaling are critical drivers of tumor progression, yet they are poorly represented in traditional …

Diabetes-Induced Mitral Valve Degeneration: Tissue-Engineered Solutions And Antioxidant Therapy, Samantha Hahn

All Theses

Mitral valve (MV) fibrosis is a progressive pathological condition characterized by leaflet thickening and stiffening, ultimately compromising valve function. This process is accelerated in diabetes, where chronic hyperglycemia elevates reactive oxygen species (ROS) and alters the mechanics of the extracellular matrix (ECM), collectively promoting the activation of valvular interstitial cells (VICs). Under healthy conditions, VICs maintain a quiescent, fibroblast-like phenotype responsible for sustaining ECM homeostasis. However, pathological biochemical cues or mechanical stress drive VICs toward a myofibroblast phenotype. While this transformation is essential for short-term repair, its persistence contributes to maladaptive MV remodeling and fibrosis. Diabetic stressors may be mitigated …

Mitral Annular Calcification In Diabetes: Valvular Interstitial Cells, Antioxidant Therapy, And Tissue Engineering Approaches, Raleigh J. Keenan

All Theses

Mitral annular calcification (MAC) is a chronic, progressive, and degenerative condition that impairs mitral valve function and increases the risk of cardiovascular disease. The mitral annulus is a saddle-shaped, fibrous structure that is primarily composed of collagen and elastin. The annulus also contains interspersed lipids that are involved in cellular metabolism, as well as inflammatory and osteogenic signaling. These lipids increase the annulus’ susceptibility to calcification, under conditions that increase mechanical stress (hypertension) and promote atherosclerosis (diabetes mellitus). These conditions intensify calcification by promoting the activation of valvular interstitial cells (VICs), increasing fibrosis, and inducing osteogenic differentiation. Although it is …

Strategic Enhancement Of Biofuel Production Using Bacillus Subtilis As A Model Organism: A Dual Approach Of Gene Essentiality Mapping And Optimization, Angela A. Zebede

Electronic Theses and Dissertations

With rising global demand for renewable energy, enhancing microbial platforms for biofuel production is vital. This study engineered Bacillus subtilis to improve resilience to solvent stress by targeting membrane lipid biosynthesis pathways essential for integrity. Growth curve analysis (OD₆₀₀) showed that phosphatidylserine (PS) and phosphatidylethanolamine (PE) knockout strains grew significantly slower than wild type (168), indicating the importance of these lipids under stress. Laurdan fluorescence spectroscopy was used to assess membrane properties. Generalized polarization (GP) analysis revealed a concentration-dependent reduction in membrane order upon 1%–2% 1-butanol exposure. GP values declined progressively from control to 2% treatment, reflecting increased membrane fluidity …

Scientific Characterization Of Historic Mortars Dating From The 15th-Century Of A Historical Building In Algeria: A Case Study, M. E. Belgacem, N. Rabahi-Touloum, R. Neves, Y. Ouldkhaoua

Journal of Sustainable Construction Materials and Technologies

This research investigates the historic mortars (Aggregate/Binder (A/B) ratio) of a historical patrimony building, dating from the 15th century, in Algeria, for restoration purposes. It is well known that thorough characterization is essential for successful restoration. To this end, several techniques, including Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), and X-ray Fluorescence (XRF), optical microscope were used to characterize the historic mortars. A mechanical test was used to characterize the compressive strength of a historic mortar. For a comprehensive characterization, A/B ratios were estimated using both Digital Image Analyses (DIA) and chemical analyses. The results obtained provided clear information on …

Computational Investigation Of The Role Of 3d Genome Architecture In The Lifecycle Of The Malaria Parasite, Srish Maulik

College of Engineering Summer Undergraduate Research Program

Malaria, a mosquito-borne infectious disease caused by the Plasmodium parasite, is responsible for more than a half a million deaths per year, the vast majority of which occur in central Africa. The parasite undergoes an incredibly complex cell molecular transformation as it transitions from living in mosquitoes to living in humans with different sets of genes being activated or silenced in order to evade the immune system of the host. Understanding how its genome guides this transition is critical for developing adequate treatments. In this project, we aim to develop a computational framework for investigating the role of the three …

A Novel Scaffold-Based Model For Stage Ii Pressure Injury Simulation: Protocol Development And Future Directions In Tissue Engineering, Skyler B. Wrubleski

Undergraduate Research and Scholarship Symposium

This study developed a 3D tissue-engineered scaffold to mimic human sacral skin for modeling pressure injuries. The scaffold consisted of a composite hydrogel of sodium alginate, gelatin, and tannic acid, crosslinked with calcium chloride. Swelling tests showed moderate hydration capacity, while wound mimic formation using a custom 3D-printed apparatus produced consistent morphology and dimensions comparable to human dermal tissue. The scaffold maintained structural integrity under prolonged compressive forces, demonstrating viability for pressure injury studies. Future work will incorporate a bilayer model with keratinocytes and fibroblasts and introduce elastin to enhance elasticity and mechanical properties. This approach aims to improve in …

Nonlinear Analytical Models Of The Seismically Isolated ``Frame-Boiler'' System With Cantilever-Type Hysteresis Dampers, Aleksandr Mikhailovich Anushchenko, Dmitrii Evgenievich Bondarev, Aleksandr Yurievich Schukin

Journal of Sustainable Construction Materials and Technologies

This study shows results of development of the ``frame-boiler'' system with hysteresis dampers analytical model. Hysteresis dampers are used as boiler antiseismic bracing. It is noted that simplified analytical models are necessary at the stage of preliminary iterative calculations, when a CAE-modeling is impractical due to significant time costs. The authors have proposed 2 options of analytical models: 2-mass model and 3-mass model. The differential equations of motion for each model are written below. The results of the calculation for seismic impacts are compared with the finite element model. It is shown that 3-mass model gives good match of results …

Advancing Sustainable Structural Solutions: Hemp Fiber-Reinforced Polymer (Hfrp) Reinforcement Bars For Concrete Applications Through Material Selection, Simulation, And Pathways For Future Development, Thomas Cadenazzi, Busra Keles

Journal of Sustainable Construction Materials and Technologies

This paper investigates innovative Hemp Fiber-Reinforced Polymer (HFRP) rebars as a sustainable alternative to conventional Carbon Steel (CS) and Glass Fiber-Reinforced Polymer (GFRP) rebars used as reinforcement in concrete structures. The feasibility of HFRP rebars is assessed, focusing on mechanical properties and sustainability advantages. A virtual tensile test on a modeled M19 HFRP rebar, conducted using Autodesk's Fusion 360, demonstrates tensile strength comparable to CS 235 and greater environmental sustainability than GFRP, despite a slight reduction in stiffness. The study also considers the potential of graphene fiber integration to enhance mechanical properties, underscoring HFRP's adaptability. Findings suggest that HFRP rebars, …

Comparative Analysis Of Life Cycle Assessment Of Traditional And Contemporary Timber Buildings, Sadık Akşar, Gökçe Tuna

Journal of Sustainable Construction Materials and Technologies

Wood has long been used as a primary building material, but with the Industrial Revolution and the spread of multi-story structures, its structural limitations became evident. In the 21st century, engineered timber products have reintroduced wood as a sustainable alternative, offering advantages such as lightness, rapid assembly, and recyclability. At the same time, buildings are responsible for significant environmental impacts, making assessment methods essential. Life Cycle Assessment (LCA) is one of the most widely used tools for evaluating these impacts across all stages of a building’s life cycle. This study applies LCA to timber construction systems, focusing on both traditional …

Sustainable Paving Block Development: Utilizing Rejected Coal As Filler And Assessing Its Impact On Paving Block’S Properties, Siti Nikmatin, Allen Kurniawan, Heriansyah Putra, Rima Fitria Adiati, Riawan Ma’Ruf, Dwi Arso Yedi Irwanto

Journal of Sustainable Construction Materials and Technologies

This study investigated the potential use of rejected coal as a fine aggregate filler in paving block production. Comprehensive characterization of the rejected coal was conducted, including toxicity, physical, chemical, and mineralogical analyses of the coal. The results showed that the rejected coal met environmental safety standards (TCLP) and had suitable properties as an aggregate. Paving blocks were produced by incorporating different proportions of rejected coal fillers and were tested for compressive strength, water absorption, and density. The optimal mix with 35% rejected coal filler as a replacement of stone ash achieved a compressive strength of 14.61 MPa, water absorption …

Numerical Comparative Study Of The Thermal Performance And Load-Bearing Capacity Of Hollow Clay Bricks Used In Construction In Libya, Osama Lawej, Mahmoud Ahmed, Ismael Ehtiwesh

Journal of Sustainable Construction Materials and Technologies

The optimization of structural and thermal performance in building components is a key challenge in sustainable construction, particularly in hot climate regions like Libya. Hollow clay bricks are widely used due to their local availability and affordability; however, their internal geometry is often not optimized for thermal resistance or mechanical integrity. This study addresses this gap by numerically investigating the effect of cavity geometry on the load-bearing capacity and thermal insulation performance of hollow clay bricks. Three configurations were analyzed, including two commercial designs from the Libyan market and a newly proposed arched cavity design. Finite Element Method (FEM) simulations …

Developing A Modular Circular Wall Over-Clad System For Facade Thermal Upgrade In Deep Energy Retrofit, Patrick Daly

Journal of Sustainable Construction Materials and Technologies

The EU has implemented several policy and legislative initiatives aimed at decarbonisation and circularity transition of the Built Environment including a strategy for large scale renovation of the building / housing stock. Modularised construction solutions are argued to be a potential acceleration pathway toward this objective. Yet there remains issues and challenges in implementing such strategies in a complex and heterogeneous stock and sector. This research investigates this decarbonisation pathway, examining the feasibility and potential of applying a modularised construction over-clad system, based on advanced circularity, in the deep energy retrofit of social housing. The research is based on a …

Ceramic Waste As Sustainable Material In Self-Compacting Concrete: Experimental Study And Ann Predictive Modeling, Abderrezak Bouziane, Houssam Slimanou, Mohamed Amin Bouzidi, Nedjima Bouzidi

Journal of Sustainable Construction Materials and Technologies

Recycling of ceramic waste in the construction sector is a promising option for reducing the environmental impacts of the concrete industry. The main objective of this study is the elaboration of a solid predictive model for ceramic waste based self-compacting (SCC) concrete properties, using artificial neural networks (ANN). This further, reduces its environmental impact without compromising satisfactory performance. An experimental approach was adopted with different substitution ratios: 0 to 30 wt% and particle sizes ranging from 3-8 mm and 8-15 mm. Tested properties of modified SCC as compressive strength at 7 and 28 days (fc7, fc28), spread (L), sieve stability …

Comparative Study On The Performance Of Ggbs, Uggbs, And Rha-Incorporated Cement Mortar Mixes, Devansh Goel, Sudarshan D. Kore

Journal of Sustainable Construction Materials and Technologies

The environmental footprint of cement production has accelerated the pursuit of sustainable alternatives in the construction industry. Supplementary cementitious materials (SCMs), particularly those derived from industrial and agricultural waste, offer a promising approach to reducing cement consumption while maintaining performance. This study evaluates the fresh and mechanical behavior of binary, ternary, and quaternary cementitious mortar blends incorporating ground granulated blast-furnace slag (GGBS), ultrafine GGBS (UGGBS), and rice husk ash (RHA) as partial replacements for cement. A total of 32 mortar mixes were designed with water-to-binder (w/b) ratios ranging from 0.3 to 0.5 and varied replacement levels of RHA (0-20%), GGBS …

Characterization Of Lactobacilli-Containing Catheter Segments Developed By Using Selective Laser Sintered Mold., Caden Maners

Master of Engineering Theses

Catheter-associated urinary tract infections (CAUTIs) are a major healthcare burden with current prevention strategies offering limited success. This study presents a novel, self-coating biomaterial approach using a silicone-based bioink embedded with thermally sensitive probiotic strains (L. crispatus, L. rhamnosus, and L. reuteri). Catheter segments were fabricated via bio-injection molding using 3D-printed CAD molds. These Lactobacilli, selected for their probiotic and antimicrobial potential, serve as a non- antibiotic strategy to reduce infection risk. These segments were evaluated for mechanical strength (Shore A hardness), thermal stability (TGA/DSC), porosity and bacterial presence (SEM), biofilm formation (crystal-violet assay), as well as mass retention in …

The Utilization Of Basic Oxygen Furnace Slag As Fine Aggregates In Concrete: Physical, Mechanical, And Durability Properties, Hakan Ozkan

Journal of Sustainable Construction Materials and Technologies

This study examines the feasibility of using basic oxygen furnace slag (BOFS) as an alternative to fine crushed limestone aggregate in concrete. BOFS is sourced from two steel production facilities in Türkiye, designated as I-BOFS and E-BOFS. The experimental results showed that as the E-BOFS aggregate replacement ratio increased, the water-to-cement (w/c) ratio increased to maintain the target workability. The concrete mixtures incorporating E-BOFS exhibited consistent reductions in the compressive strength with an increase in the BOFS ratio. At the same time, I-BOFS maintained higher compressive strength, with only minor losses up to 80% of the substitution ratio. Flexural strength …

Development Of A Self-Cured Alkali-Activated Mortar, Kübra Ekiz Barış

Journal of Sustainable Construction Materials and Technologies

Alkali-activated mortars (AAM) can be produced with self-curing (SC), which supplies internal moisture to accelerate alkaline-activation reactions. The aim of using SC is to make AAMs with an early-age strength without any additional curing energy consumption and higher CO2 emissions, and to obtain in-situ practical advantages that enable the large-scale application of AAMs. The previous study produced natural pozzolan-based AAMs by applying energy-intensive heat (HC), microwave (MWC), and hybrid (HC+MWC) curing. This study investigates alternative curing regimes that reduce production energy without compromising material properties. The impacts of air curing (AC), water curing (WC), and SC on the properties were …