Biomedical Engineering and Bioengineering Commons^™

Theoretically Proposed Optimal Frequency For Ultrasound Induced Cartilage Restoration, April D. Miller, Anuradha Subramanian, Hendrik J. Viljoen

Department of Chemical and Biomolecular Engineering: Faculty Publications

Background: Matching the frequency of the driving force to that of the system’s natural frequency of vibration results in greater amplitude response. Thus we hypothesize that applying ultrasound at the chondrocyte’s resonant frequency will result in greater deformation than applying similar ultrasound power at a frequency outside of the resonant bandwidth. Based on this resonant hypothesis, our group previously confirmed theoretically and experimentally that ultrasound stimulation of suspended chondrocytes at resonance (5 MHz) maximized gene expression of load inducible genes. However, this study was based on suspended chondrocytes. The resonant frequency of a chondrocyte does not only depend on the …

Segmental Movement Compensations In Patients With Transtibial Amputation Identified Using Angular Momentum Separation, Brecca M. M. Gaffney

Electronic Theses and Dissertations

Patients with unilateral dysvascular transtibial amputation (TTA) adopt movement compensations that are required to maintain balance and achieve ambulation in the absence of ankle plantar flexion, and result in increased and asymmetric joint loading patterns. As a result, this population is at an increased risk of overuse injuries, such as low back pain (LBP). Clinical gait analysis is used to guide diagnostics in movement retraining following amputation, and is performed using instrumented (research based) or observational analyses (clinically based). However, instrumented analyses are currently impractical in most clinical settings due to expense and computational limitations. This dissertation presents the use …

Statistical Shape Modeling To Quantify Variation In The Proximal Humeral Anatomy, Paul B. Sade Sr.

Electronic Theses and Dissertations

The fit of the humeral prosthesis to the intramedullary canal and the replication of the anatomic humeral head center are important factors in Total Shoulder Arthroplasty (TSA). The objective of this thesis was to develop a Statistical Shape Model (SSM) of the cortical and cancellous bone regions of the proximal humerus, and to assess potential shape differences with gender and ethnicity, with a goal of informing implant design. An SSM was used and Principal Component Analysis (PCA) was applied to data that represented both the cancellous and cortical humeral bone of 63 healthy subjects and cadavers. Anatomical measurements and PC …

Six Degrees Of Freedom: Kinematics Of The Healthy Ankle Syndesmosis Joint, Veronica A. Hogg-Cornejo

Electronic Theses and Dissertations

Syndesmotic injury, more commonly known as a "high ankle sprain", accounts for over 12% of all ankle sprain incidents in the US; of which, over 25% occur during a sporting activity. Typically, harm to the syndesmosis occurs in sports such as football, soccer, lacrosse, and hockey where it is common for an athlete to experience rapid and extreme dorsiflexion-external rotations of the foot. Severe syndesmotic sprains have been noted by clinicians as the most difficult ankle injury to accurately diagnose and treat, require the most recuperation time, and often results in life-long dysfunction. Even more problematic, 40% of patients suffering …

Specimen-Specific Natural, Pathological, And Implanted Knee Mechanics Using Finite Element Modeling, Azhar Akber Ali

Electronic Theses and Dissertations

There is an increasing incidence of knee pain and injury among the population, and increasing demand for higher knee function in total knee replacement designs. As a result, clinicians and implant manufacturers are interested in improving patient outcomes, and evaluation of knee mechanics is essential for better diagnosis and repair of knee pathologies. Common knee pathologies include osteoarthritis (degradation of the articulating surfaces), patellofemoral pain, and cruciate ligament injury and/or rupture. The complex behavior of knee motion presents unique challenges in the diagnosis of knee pathology and restoration of healthy knee function. Quantifying knee mechanics is essential for developing successful …

Statistical Shape And Intensity Modeling Of The Shoulder, Irene Sintini

Electronic Theses and Dissertations

Anatomical variability in the shoulder is inherently present and can influence healthy and pathologic biomechanics and ultimately clinical decision-making. Characterizing variation in bony morphology and material properties in the population can support treatment and specifically the design, via shape and sizing, of shoulder implants. Total Shoulder Arthroplasty (TSA) is the treatment of choice for glenohumeral osteoarthritis as well as bone fracture. Complications and poor outcomes in TSA are generally influenced by the inability of the implant to replicate the natural joint biomechanics and by the bone quality around the fixation features. For this reason, knowledge of bony morphology and mechanical …

Combination Of Bmp-2 And Relaxin To Induce Osteogenesis In Vivo, Sahitya Injamuri

Masters Theses

"Bone grafts are a common procedure for treating craniofacial injuries such as trauma, surgery, and reconstruction. Autografts and allografts have limitations which encourages the use of synthetic bone grafts. While synthetic bone grafts, such as hydroxyapatite (HA) microspheres, are advantageous for their cost and reproducibility, they lack the cells and growth factors needed for proper osteoinduction. Bone morphogenetic protein-2 (BMP-2) has been shown to increase the osteoinduction of grafts but the effective dose is above physiological levels and causes undesired effects on the body. Relaxin has been shown to enhance BMP-2's ability to induce bone formation in vitro and thus …

Evaluating Outer Segment Length As A Surrogate Measure Of Peak Foveal Cone Density, Melissa A. Wilk, Brandon M. Wilk, Christopher S. Langlo, Robert F. Cooper, Joseph Carroll

Biomedical Engineering Faculty Research and Publications

Adaptive optics (AO) imaging tools enable direct visualization of the cone photoreceptor mosaic, which facilitates quantitative measurements such as cone density. However, in many individuals, low image quality or excessive eye movements precludes making such measures. As foveal cone specialization is associated with both increased density and outer segment (OS) elongation, we sought to examine whether OS length could be used as a surrogate measure of foveal cone density. The retinas of 43 subjects (23 normal and 20 albinism; aged 6–67 years) were examined. Peak foveal cone density was measured using confocal adaptive optics scanning light ophthalmoscopy (AOSLO), and OS …

Diffusion Tensor Imaging Correlates With Short-Term Myelopathy Outcome In Patients With Cervical Spondylotic Myelopathy, Aditya Vedantam, Avinash Rao, Shekar N. Kurpad, Michael B. Jirjis, Gerald Eckardt, Brian D. Schmit, Marjorie C. Wang

Biomedical Engineering Faculty Research and Publications

Objective

To determine if spinal cord diffusion tensor imaging indexes correlate with short-term clinical outcome in patients undergoing elective cervical spine surgery for cervical spondylotic myelopathy (CSM).

Methods

A prospective consecutive cohort study was performed in patients undergoing elective cervical spine surgery for CSM. After obtaining informed consent, patients with CSM underwent preoperative T2-weighted magnetic resonance imaging and diffusion tensor imaging of the cervical spine. Fractional anisotropy (FA) values at the level of maximum cord compression and at the noncompressed C1-2 level were calculated on axial images. We recorded the modified Japanese Orthopaedic Association (mJOA) scale, Neck Disability Index, and …

Lessons Learned From A 10-Year Collaboration Between Biomedical Engineering And Industrial Design Students In Capstone Design Projects, Jay R. Goldberg, Pascal Malassigné

Biomedical Engineering Faculty Research and Publications

Engineers and industrial designers have different approaches to problem solving. Both place heavy emphasis on identification of customer needs, manufacturing methods, and prototyping. Industrial designers focus on aesthetics, ergonomics, ease of use, manufacturing methods, and the user’s experience. They tend to be more visual and more concerned with the interaction between users and products. Engineers focus on functionality, performance requirements, analytical modeling, and design verification and validation. They tend to be more analytical and more concerned with the design of internal components and product performance. Engineers and industrial designers often work together on project teams in industry. Collaboration between the …

Limb Stabilization In Older Adults And Chronic Stroke Survivors: A Pilot Study, Raymond C. Doudlah, Robert A. Scheidt, Aaron J. Suminski

Biomedical Engineering Faculty Research and Publications

Visual fidelity influences many aspects of daily living, including stabilizing wrist movements against environmental perturbations. Here, we present a pilot investigation to determine how visual feedback impacts wrist stabilization for populations with age related declines in motor function and chronic stroke. To quantify these interactions, behavioral performance and local brain activation were observed during a task requiring stabilization of the wrist against constant and stochastic extensor torque perturbations. All subjects were better able to stabilize their wrist when veridical visual feedback of their limb was provided. Examination of the neural activation maps in the Control and Aging populations revealed patterns …

Effects Of Training Intensity On Locomotor Performance In Individuals With Chronic Spinal Cord Injury: A Randomized Crossover Study, Gabrielle Brazg, Meghan Fahey, Carey L. Holleran, Mark Connolly, Jane Woodward, Patrick W. Hennessy, Brian D. Schmit, T. George Hornby

Biomedical Engineering Faculty Research and Publications

Background. Many physical interventions can improve locomotor function in individuals with motor incomplete spinal cord injury (iSCI), although the training parameters that maximize recovery are not clear. Previous studies in individuals with other neurologic injuries suggest the intensity of locomotor training (LT) may positively influence walking outcomes. However, the effects of intensity during training of individuals with iSCI have not been tested. Objective. The purpose of this pilot, blinded-assessor randomized trial was to evaluate the effects of LT intensity on walking outcomes in individuals with iSCI. Methods. Using a crossover design, ambulatory participants with iSCI >1 year duration performed either …

A Wireless, Passive Sensor For Measuring Temperature At Orthopedic Implant Sites For Early Diagnosis Of Infections, Salil Sidharthan Karipott

Dissertations, Master's Theses and Master's Reports

Sensorized implants with embedded wireless, passive temperature sensors were developed for early detection of implant-associated infections. The operation principle of the sensor is based on the hypothesis that infections can lead to an increase in local temperature prior to the rise of body temperature. The sensor was an inductive capacitive (LC) circuit that has been used for monitoring of different parameters wirelessly, often in difficult to access environments. The sensor was fabricated on to an interference screw, which is used for tendon and ligament reconstruction surgeries. In this project, a sensorized interference screw was designed and fabricated by accommodating an …

Design Of Robust Hydrogel Based On Mussel-Inspired Chemistry, Yuan Liu

Dissertations, Master's Theses and Master's Reports

The structure of catechol is found in mussel adhesive proteins and contributed to both wet-resistant adhesion and cohesive curing of these proteins. A synthetic nano-silicate, Laponite was incorporated into catechol-containing hydrogels and the hydrogel network-bound catechol formed strong reversible interfacial interaction with Laponite. The contribution of incorporated catechol-Laponite reversible interfacial interactions to the mechanics of hydrogels constructed by different strategies was studied. In the first strategy, Laponite and catechol were introduced into the double network hydrogel (DN) via the free radical co-polymerization of a catechol-containing monomer, backbone monomer, and crosslinker. The introduction of catechol-Laponite interactions significantly improved the compressive strength …

Implantable Wireless Sensor Networks: Application To Measuring Temperature For In Vivo Detection Of Infections, Praharsh Madappaly Veetil

Dissertations, Master's Theses and Master's Reports

It is has been proven that infection in the body cause a local temperature increase due to localized inflammation. Therefore, a method to provide early diagnostic or long-term tracking of this infection will provide great benefits to patients with diabetic foot ulcers or sickle cell disease, and those receiving hemodialysis where they suffer from a weakened immune system. The goal of this project is to develop an implantable wireless temperature sensor based on a wireless sensor network system for monitoring infections in situ. The analog signals from the thermistors are digitized and wirelessly transmitted to a computer with an ez430-rf2500 …

A 3d Biomimetic Scaffold Using Electrospinning For Tissue Engineering Applications, Samerender Nagam Hanumantharao

Dissertations, Master's Theses and Master's Reports

Electrospinning holds great promise for designing functional 3D biomimetic scaffolds for tissue engineering applications. The technique allows for the reproducible fabrication of 3D scaffolds with control over the porosity and thickness. In this work, a novel method for the synthesis of a 3D electroactive scaffold using electrospinning from polycaprolactone (PCL), Polyvinylidene Fluoride (PVDF) and Polyaniline (PANI) is reported. Additional scaffolds involving different morphologies of PCL, PCL-PVDF and PCL-PANI-PVDF were also fabricated and evaluated. The scaffolds were characterized using electron microscopy to visualize the morphologies. Infrared spectroscopy was used to confirm the presence of polymers and their respective phases in the …

Computational Ultrasound Elastography: A Feasibility Study, Yu Wang

Dissertations, Master's Theses and Master's Reports

Ultrasound Elastography (UE) is an emerging set of imaging modalities used to assess the biomechanical properties of soft tissues. UE has been applied to numerous clinical applications. Particularly, results from clinical trials of UE in breast lesion differentiation and staging liver fibrosis indicated that there was a lack of confidence in UE measurements or image interpretation. Confidence on UE measurements interpretation is critically important for improving the clinical utility of UE. The primary objective of my thesis is to develop a computational simulation platform based on open-source software packages including Field II, VTK, FEBio and Tetgen. The proposed virtual simulation …

Surface Enabled Lab-On-A-Chip (Loc) Device For Protein Detection And Separation, Zhichao Wang

Dissertations, Master's Theses and Master's Reports

Sensitive and selective chemical/biological detection/analysis for proteins is essential for applications such as disease diagnosis, species phenotype identification, product quality control, and sample examination. Lab-on-a-chip (LOC) device provides advantages of fast analysis, reduced amount of sample requirements, and low cost, to magnificently facilitate protein detection research. Isoelectric focusing (IEF) is a strong and reliable electrophoretic technique capable of discerning proteins from complex mixtures based on the isoelectric point (pI) differences. It has experienced plenty of fruitful developments during previous decades which has given it the capability of performing with highly robust and reproducible analysis. This progress has made IEF devices …

How A Diverse Research Ecosystem Has Generated New Rehabilitation Technologies: Review Of Nidilrr’S Rehabilitation Engineering Research Centers, David J. Reinkensmeyer, Sarah Blackstone, Cathy Bodine, John Brabyn, David Brienza, Kevin Caves, Frank Deruyter, Edmund Durfee, Stefania Fatone, Geoff Fernie, Steven Gard, Patricia Karg, Todd A. Kuiken, Gerald F. Harris, Mike Jones, Yue Li, Jordana Maisel, Michael Mccue, Michelle A. Meade, Helena Mitchell, Tracy L. Mitzner, James L. Patton, Philip S. Requejo, James H. Rimmer, Wendy A. Rogers, W. Zev Rymer, Jon A. Sanford, Lawrence Schneider, Levin Sliker, Stephen Sprigle, Aaron Steinfeld, Edward Steinfeld, Gregg Vanderheiden, Carolee Winstein, Li-Qun Zhang, Thomas Corfman

Biomedical Engineering Faculty Research and Publications

Over 50 million United States citizens (1 in 6 people in the US) have a developmental, acquired, or degenerative disability. The average US citizen can expect to live 20% of his or her life with a disability. Rehabilitation technologies play a major role in improving the quality of life for people with a disability, yet widespread and highly challenging needs remain. Within the US, a major effort aimed at the creation and evaluation of rehabilitation technology has been the Rehabilitation Engineering Research Centers (RERCs) sponsored by the National Institute on Disability, Independent Living, and Rehabilitation Research. As envisioned at their …

The Effect Of Twist On The Mechanical Properties Of The Intervertebral Disc, Maxine Harvey-Burgess

Theses and Dissertations (Comprehensive)

Introduction: Intervertebral disc (IVD) herniation is a common injury to the IVD and a frequent source of low back pain. IVD herniation occurs when the nucleus pulposus migrates through both the inter- and intralamellar matrices of the annulus fibrosus (AF). There are a number of mechanical risk factors associated with herniation, including repetitive flexion and twist. In vivo, twist combined with repetitive flexion has been associated with increased experience of low back pain and herniation. Additionally, in vitro, when repetitive flexion is combined with twist, IVD herniation occurs more easily than repetitive flexion alone. However, the mechanisms behind …