Biomedical Engineering and Bioengineering Commons^™

Estimation Of Unmeasurable External Disturbances Of A Dynamic Object Based On A Robust Adaptive Kalman Filter, Bunyod Mamurjon Ugli Buronov

Technical science and innovation

This article considers the problem of directly estimating unmeasurable external disturbances acting on a dynamic object under the condition that the state vector of the object is available for measurement. In the considered case, the problem is reduced to the estimation of an unknown input of a dynamic system. It is shown that when the system state is measurable, both a direct inversion scheme based on the object’s dynamic equation and filtering methods that eliminate the need for coarse numerical differentiation can be applied. For slowly varying disturbances, a random walk model with a small process noise covariance is proposed, …

Evaluation Of The Metrological Characteristics Of An Ultrasonic Flowmeter For Water Resources, Makhsud Idrisovich Makhmudov, Uktam Farkhodovich Mamirov, Siroj Sobirovich Nurov

Technical science and innovation

This paper presents the results of evaluating the metrological characteristics of a developed ultrasonic flowmeter intended for measuring water flow in open channels. The study analyzes the main sources of measurement errors and classifies them into methodological, instrumental, additional, systematic, and random components. Experimental investigations were carried out to estimate the random and systematic errors under steady-state flow conditions. Using the least-squares method, the systematic error was separated into additive and multiplicative components, providing a basis for calibration and correction of the measurement results. The reliability of the developed measuring instrument was evaluated using the failure rate method based on …

Mathematical Modelling Of Nitrification And Denitrification Processes Based On Neuro-Fuzzy Bioreactor Models, Mirkhalil Agzamovich Ismailov, Boburbek Zokirjon Ugli Mannobjonov

Technical science and innovation

This paper presents the development and investigation of hybrid neural network and fuzzy models for the mathematical modelling of nitrification and denitrification processes in a biological wastewater treatment bioreactor. A comprehensive approach is proposed, integrating a mechanistic model of the ASM1/ASM2d type with neural networks (LSTM and Gaussian Process Regression), as well as a fuzzy control system based on an extended set of expert rules. A digital twin of the bioreactor was developed to allow for the prediction of the dynamic behavior of key parameters such as NH₄⁺, NO₃⁻, dissolved oxygen, etc. within a prediction range of 1 to 12 …

Analysis And Study Of The Content Of Chloride Salts In Oil, Natalia Evgenievna Sheina, Muborak Akramovna Mirshomilova

Technical science and innovation

The article addresses the critical issue of crude oil quality control, specifically focusing on the determination of chloride salts (sodium, calcium, and magnesium), which exert a destructive impact on processing equipment. The paper provides a detailed analysis of the adverse effects of salts, which lead to severe equipment corrosion, scaling, and a reduced yield of valuable oil fractions. The chemical principles and specific applications of two standardized methods for analyzing aqueous extracts according to GOST 21534-2021 and ASTM D3230 are described: indicator (argentometric and mercurimetric) and potentiometric titration. The experimental section presents the results of a comparative analysis of crude …

Analysis And Optimization Of Intelligent Control Of The Drying Process Under Uncertainty, Azizbek Nodirbekovich Yusupbekov, Marufjon Kobuljonovich Shodiev, Khusniddin Mamarasul Ugli Esonov

Technical science and innovation

This section proposes a multi-criteria Pareto-optimization algorithm, integrated with Herbert Simon's four-stage decision-making scheme (Intelligence–Design–Choice–Implementation) and an ANFIS-based adaptive controller, for simultaneously optimizing the mutually conflicting quality, energy, and time criteria of the wheat-drying process. The algorithm for constructing the set of Pareto-optimal solutions and selecting the compromise solution closest to the ideal point is presented step by step. The implementation of the ANFIS controller in the MATLAB/Simulink environment is comprehensively verified through a simulation block diagram, the Rule Viewer, the Surface Viewer, the training error-function graph, the RMSE convergence graph, and a learning-curve analysis. Training was carried out on …

Evaluation Of Level Measurement Uncertainty For Three Types Of Laser Level Meters Using The Gum Methodology: Calculated Uncertainty Budgets, Uncertainty Profile, And Hardware Component Requirements, Lazizbek Furkatjanovich Saidoripov, Barat Makhmudovich Akhmedov

Technical science and innovation

A methodology is presented for evaluating the uncertainty of liquid petroleum product level measurements using laser level meters based on different measurands’ informative parameters: propagation time, phase difference, and image coordinates. Based on analytical expressions for error components and a traceability chain to the national length standard, calculated uncertainty budgets are developed in accordance with JCGM 100 for time-of-flight, phase-based, and laser–television level meters. Under the assumed input conditions, the expanded uncertainties (k = 2) are 1.66, 0.73, and 1.02 mm, respectively. For the laser–television level meter budget, the Gaussian approximation is verified using the Monte Carlo method (JCGM 101): …

Development Of An Experimental Stand For The Study Of The Directions Of Movement And Velocity Of Air Flows In The Pneumatic Channel Of The Final Aspiration Of The Muz-16 Air Sieve Separator, Hanna Borisovna Torgan, Zulfiya Kakhramonovna Ergasheva

Technical science and innovation

The article presents the results of experimental studies on the rheological properties of pasta dough obtained from various types of wheat flour (bakery highest grade, as well as durum varieties of Belarusian selection). The regularities of changes in the yield shear stress, plastic viscosity, and shear rate of the semi-finished product were studied depending on the key technological factors of extrusion: moisture content (0.28–0.335 kg/kg), temperature (25–55 °C), and discharge pressure (up to 88 · 10^-5 Pa). The operating principle and design features of the modernized pressing unit and die using special converging-diverging (confuser-diffuser) inserts (according to the patents …

Research On The Effectiveness Of Various Methods For Primary Processing Of Silkworm Cocoons, Doston Ishmukhammat Ugli Samandarov

Technical science and innovation

This article presents the results of experimental studies of the primary processing (killing) of silkworm pupae using existing technological methods, as well as three different combinations of infrared (IR) and ultrasound (US). A series of pilot studies was conducted in the laboratory of the Department of Service Technology at Tashkent State Technical University on nine cocoon samples using existing technological equipment and an experimental setup developed under project AL-8724053050 and based on the combined effects of infrared radiation and ultrasound. A comparative evaluation of the studied processing methods was conducted based on the degree of pupal killing, moth hatching, process …

Experimental Study On The Behavior Of High-Strength Reinforced Concrete Beams With A Longitudinal Void, With And Without Micro Steel Fibers, At Different Shear Spans, Farah M. Hussein, Saif Altai, Shatha Alasadi, Ayoob A. Ibrahim, Arshad Nadhom Shubber

Journal of Sustainable Construction Materials and Technologies

This study examines the impact of creating a longitudinal void in high-strength reinforced concrete (RC) beams to decrease concrete volume. Testing involved three groups: solid beams (SB), beams with a 75 mm void (VB), and beams with a void incorporating 1.2% micro-steel fibers (VBSF), across various shear spans (a/d) of 1.8, 2.7, and 3.6. Results indicated that increased a/d led to a 54.2% reduction in peak loads and a 119.2% increase in deflection for solid beams. The void negatively affected load-bearing at a/d = 1.8 with a 25% peak load reduction and brittle failure. At a/d = 2.7, effects were …

Parametric Study On The Plastic Hinge Length Of Precast Concrete Columns With Grouted Sleeve Connections, Rizky Tri Amalia, Harun Alrasyid

Journal of Sustainable Construction Materials and Technologies

The use of precast concrete structures with grouted sleeve (GS) connections has gained significant traction in the acceleration of bridge construction. The plastic hinge length (Lp) is a critical parameter for assessing the seismic performance and deformation capacity of such structural members. The previous study has proposed empirical equations for Lp in monolithic columns; however, a comprehensive understanding of the influential parameters on Lp in precast concrete columns with GS connections remains limited. This study presents a detailed parametric investigation to evaluate the effects of key design parameters on the plastic hinge length of a precast concrete columns with GS …

Evolution Of Raman And Photoluminescence Response In Molybdenum Disulfide Thin Films Deposited Via Thermal Atomic Layer Deposition, Wesley Jen, John D. Hues, Icelene Leong, Nolan H. Olaso, Ravindra K. Kanjolia, Mansour Moinpour, Steven M. Hues, Elton Graugnard

Boise State University Publications and Presentations

In order to enable further advances in microelectronics, new processes capable of precisely depositing films are required. This is especially true of processes meant for depositing two-dimensional (2D) transition metal dichalcogenides, such as MoS2, a material of particular interest due to its high potential mobility even at a thickness of a few atoms. In this work, we report industry-compatible processes for depositing crystalline MoS2 with a high degree of precision. We demonstrate the successful conversion of both MoOx and MoSx films deposited via thermal atomic layer deposition using bis(tert-butylimido)bis(dimethylamino)Mo(VI) and H2O or H2S, respectively, into crystalline MoS2 films after an …

An Investigation Of Pelvic Kinematics And Implications For Total Hip Arthroplasty, Kathryn Holland Colone

Electronic Theses and Dissertations

Total hip arthroplasty (THA) is one of the most commonly performed orthopaedic procedures, with approximately 500,000 surgeries performed annually in the United States alone. Although THA is widely regarded as highly successful, postoperative complications persist, highlighting the multifactorial nature of THA outcomes. Previous studies have demonstrated the importance of implant positioning and soft tissue mechanics, yet challenges remain in optimizing surgical decisions on a patient-specific basis. Recent advances in surgical planning tools have shifted the focus of preoperative planning toward optimizing patient-specific outcomes, highlighting the need to better understand how patient anatomy, surgical technique, and joint mechanics interact to influence …

Time-Frequency Analysis Of Arterial Pulse Signals Of Cardiovascular Disease Patients Measured By A Microfluidic-Based Tactile Sensor, Md Mahfuzur Rahman

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation presents a single-degree-of-freedom (SDOF) based time–frequency analysis framework that can simultaneously extract a comprehensive set of cardiovascular autonomic indices from arterial pulse wave recordings obtained at rest and post-exercise, supporting non-invasive monitoring of autonomic recovery during cardiac rehabilitation. The framework rests on three technical contributions.

First, an SDOF analytical model of motion artefacts quantifies two physically distinct distortion mechanisms: additive baseline drift and Time-Varying System Parameter (TVSP) generated distortion of the Tissue-Contact-Sensor (TCS) stack. Baseline drift is slowly varying and removable by filtering; TVSP distortion rides on all harmonics of the true pulse signal and cannot be removed …

Straw As A Potential Vegetable Fibre Insulative Infill In Framed Constructions - Material Testing\Tnotereftnote1, Patrick Daly

Journal of Sustainable Construction Materials and Technologies

The construction sector faces increasing pressure to reduce embodied carbon and adopt circular material strategies, with bio-based materials offering a promising pathway. Straw-based insulation, particularly in loose-fill form, has gained traction in Europe, where several products have achieved certification under EAD 040138-01-1201. This study investigates the potential of Irish-processed straw chip as a bio-based insulative infill for framed construction by evaluating its material properties and thermal conductivity–density performance relative to European ETA-certified reference products. A programme of laboratory testing was undertaken on commercially available Irish straw samples, including material characterisation (moisture content, particle morphology, and dust content) and thermal conductivity …

Development And Characterization Of Mycelium-Based Biocomposites From Ganoderma Lucidum Using Spent Yerba Mate And Residual Sunflower Oil For Sustainable Insulation In Construction, Paula V. Alfieri, Guadalupe Canosa

Journal of Sustainable Construction Materials and Technologies

The construction industry urgently requires sustainable alternatives to petroleum-based insulation materials such as expanded polystyrene (EPS) and mineral wool. Mycelium-based biocomposites offer a promising solution by valorizing agricultural waste while delivering competitive thermal and acoustic performance. In this study, developed and characterized biocomposites using Ganoderma lucidum mycelium combined with spent yerba mate and residual sunflower oil (70 g/30 mL), both commonly generated as waste in Argentine institutions. Two formulations were evaluated: high density (HD: 280 ± 5 kg/m³) and low density (LD: 185 ± 5 kg/m³). Samples were cultivated for 90 days at 28 °C and 65% relative humidity and …

Comparative Life Cycle Assessment Of Hemp Walls In Residential Construction In Morocco, Hicham Kaddouri, Rachida Elbarghmi, Firyal Latrache, Marwane Hammouti, Abderrahim Abidouche, Ismael Driouch

Journal of Sustainable Construction Materials and Technologies

This study analyzes the energy and environmental performance of hemp-based wall solutions applied to Moroccan residential buildings by combining dynamic thermal simulation and life cycle assessment (LCA). A reference building is assessed under four representative Moroccan climates (Al Hoceima, Oujda, Marrakech, and Ouarzazate), comparing a conventional wall retrofitted with hemp plaster and a wall incorporating hemp concrete. The results show that hemp concrete significantly reduces annual heating and cooling energy demands by 20–24% depending on the climate, with heating needs decreasing by up to 40% and cooling needs by approximately 15%, particularly in hot and arid regions. The LCA reveals …

Dual-Waste Integration For Geotechnical Improvement: Silica Fume And Eggshell Ash In Kaolin Soil Stabilization, Ng Jun Shen, Muzamir Hasan, Siti Sarah Eliyun, Md. Ikramul Hoque, Mohamad Afiq Jazrin Mohamad Sidek

Journal of Sustainable Construction Materials and Technologies

This study reveals the potential substitution of silica fume and eggshell ash in the technique of soil stabilization, varying across distinct proportions in the modification of geotechnical parameters. The untreated kaolinitic soil which has low soil bearing capacity in nature is frequently reflected in its mechanical instability, for instance, soil settlement and extreme compressibility. By associating the industrial and agricultural material, it is potentially to resolve the above-mentioned issues with explicit designs. A number of laboratory approaches have been implemented in the assessment of basic geotechnical properties, including grain size distribution, Atterberg limits, specific gravity, proctor properties, and shear strength …

Performance Evaluation And Sustainable Benefits Of Using Metakaolin And Recycled Steel Fibers In Concrete, Lova Raju Surla, Ramprasad Naik Desavathu, Raja Murugadoss Jeyaraju

Journal of Sustainable Construction Materials and Technologies

The rapid accumulation of waste vehicle tires and the increasing demand for cement pose significant environmental challenges through land pollution and CO2 emissions. The combined use of recycled steel fibers (RSFs) recovered from waste tires and supplementary cementitious materials (SCMs) offers a sustainable solution to these issues. This study investigates concrete incorporating 20% fly ash (FA), varying metakaolin (MK) contents (4–16%), and RSF dosages of 0.5–1.5%. Mechanical properties (compressive, split tensile, and flexural strengths) and durability characteristics (sorptivity, water absorption, chloride permeability, and homogeneity) were evaluated at 7, 28, and 90 days. Results showed that the mixture containing 20% FA …

Climate-Responsive Design For Sustainable Construction: Passive Strategies In Domestic Architecture Supporting Sustainability, Nahed Chakouf

Journal of Sustainable Construction Materials and Technologies

This study explores climate-responsive design in domestic architecture, focusing on the application and effectiveness of passive strategies across various climatic regions, including the UK, hot-arid, tropical, and cold climates. A qualitative comparative case study method was used to explore different passive design strategies, integration of sustainability, procurement, the coordination of stakeholders, and compliance with regulations in residential architectural projects under varying climate conditions. Drawing from a combination of historical case studies and original architectural projects, the research evaluates how spatial configuration, material selection, solar orientation, shading, ventilation, and insulation are optimized to achieve thermal comfort and energy efficiency. In temperate …

Modeling Of Terpolymerization Kinetics And Determination Of Reactivity Ratios In The Tdma–Styrene–Maleic Anhydride System, Shohrux Boboxon Ugli Mavlonov, Sadriddin Fayzullayevich Fozilov

Technical science and innovation

In this study, the kinetics of terpolymerization, compositional evolution, and monomer reactivity ratios in the TDMA–styrene–maleic anhydride system were comprehensively investigated. Increasing the initiator concentration from 16.8×10⁻⁶ to 51.3×10⁻⁶ mol•L⁻¹ led to an increase in conversion from 6.4% to 15.2% and reaction rate from 4.075×10⁻⁶ to 8.965×10⁻⁶ mol•L⁻¹•s⁻¹. At low conversion (Xw≈0.02–0.09), the terpolymer composition remained close to the initial feed, although deviations due to differences in monomer reactivity were observed. With increasing conversion, some systems exhibited stable composition (±0.02), while others showed compositional drift (increase of MA fraction from 0.50 to 0.70). The determined reactivity ratios (rTDMA/St≈0.99; rSt/TDMA≈1.62; rTDMA/MA≈2.02; …

Calculation Of The Basic Parameters Of The Hybrid Power Plant (Hpu) On The Spark Car, Rustam Raximovich Tillahodjaev, Jamoliddin Pardaboy Ugli Turdiev

Technical science and innovation

This article presents one of the effective ways to improve fuel efficiency and reduce emissions of toxic substances, the use of internal combustion engines with the use of an electric drive in their designs. In recent years, two directions in the development of cars with electromechanical drives have been clearly identified, the first is the creation of a pure electric car, the second is the development of an electromechanical drive with a combined (hybrid) power plant. Due to the lack of efficient energy storage available for mass production, pure electric vehicles have relatively low mileage on a single charge. This …

Experimental Study Of An Automotive Cooling System With A Mechatronic Control System, Avaz Israilovich Yangibayev

Technical science and innovation

This article presents the results of experimental investigations of a passenger car engine cooling system equipped with a mechatronic control system. The experiments were conducted on an intelligent hardware-software laboratory test bench developed using original components of a Chevrolet Gentra vehicle. The study determined the thermodynamic response characteristics and energy performance of the system under varying ambient temperatures (-10 to +50 °C) and engine thermal loads. The experimental results demonstrated that the mechatronic system can maintain coolant temperature with minimal fluctuation amplitude, ensure smooth transient processes, and significantly reduce electrical energy consumption. Based on the obtained results, scientific and practical …

Use Of New Improved Methods For Assessing The Engineering-Geological Characteristics Of Deposits By Depth (Using The Example Of The Akba Deposit)., Elboy Shavkatovich Qurbonov Salom, Abduboqib Djalilovich Karimov, Yokub Yarash Ugli Isomiddinov

Technical science and innovation

The article examines the fracturing and filtration properties of rocks in boreholes, rock outcrops, and underground mine workings at the Akba gold deposit. Based on the results of hydrogeological and engineering-geological studies, methods that fully meet modern requirements were used, the values of the RMR rating of rocks and the indicators of the qualitative content of RQD rocks, as well as the intervals of their changes, were studied, as a result of which it became possible to quickly and accurately assess the strength state of the rock mass of the deposit territory by depth and area.

Investigation Of Energy Efficiency Of An Autonomous Mobile Photovoltaic-Thermal (Pv/T) System With A Polycarbonate Absorber, Sanjar Kodir Ugli Shoguchkarov, Anvar Rakhmat Ugli Rakhmatov, Rushana Husen Kizi Abdullaeva, Orazbek Maratbay Ugli Temirbaev

Technical science and innovation

This study analyzes the enhancement of energy efficiency in photovoltaic-thermal (PV/T) systems, which enable the simultaneous generation of electrical and thermal energy from solar radiation. The research focus is an autonomous mobile unit based on multi-channel polycarbonate heat collectors with a hydraulic diameter of 8 mm, characterized by their lightweight nature and superior corrosion resistance compared to conventional metal absorbers. Experimental investigations were conducted at the solar testing field of the Physical-Technical Institute of the Academy of Sciences of Uzbekistan under extreme continental climatic conditions to determine the system's stable thermophysical indicators. The results demonstrated that active water cooling using …

Development Of An Optimal Composition Of A Composite Solvent For Asphalt–Resin–Paraffin Deposits, Gulmira Abduvaliyevna Tadjiyeva, Xasan Irgashevich Kadirov, Shaxnoza Abduvaliyevna Tadjiyeva, Fazliddin Zokir Ugli Murodullayev, Bekmurodjon Baxtiyorjon Ugli Raximjonov

Technical science and innovation

A solvent formulation composed of aromatic hydrocarbons of the C9 fraction and aliphatic alcohols in a 1:1 ratio, supplemented with 1–3 wt.% of a nonionic surfactant, has been developed. The proposed composition demonstrates more than a twofold increase in dissolving and washing efficiency toward paraffin-type asphaltene–resin deposits. Furthermore, the solvent system exhibits pronounced depressant–dispersant properties with respect to paraffin-containing organic deposits. Although numerous investigations have addressed the development of technologies for removing organic deposits in oilfield equipment—primarily focusing on specific aspects of eliminating or preventing asphaltene–resin–paraffin deposits (ARPD) in wells—limited attention has been given to the design of integrated approaches. …

Adaptive – Compositional Method For Coordinating Subsystems At Different Levels In Hierarchical Control Systems, Husan Zakirovich Igamberdiyev, Uktam Farxodovich Mamirov Mr, Inomjon Ilxom Ugli Abdukaxxarov Mr

Technical science and innovation

This paper examines the problem of synthesizing algorithms for the composition of subsystems at various levels within complex hierarchical control systems under conditions of uncertainty and resource constraints. It is demonstrated that classical composition algorithms, which rely on the intersection of admissible sets and the use of local optimality criteria, suffer from several significant drawbacks. These include a combinatorial increase in complexity, dependence on the expert selection of parameters, and limited applicability in dynamic environments. To overcome these shortcomings, an adaptive-compositional method is proposed. This method is based on the dynamic recalculation of coordination parameters, the integration of model predictive …

Technology For Obtaining Aliphatic Amines Based On Liquid By-Products Of Polymerization Processes, Kamila Sabirbaevna Allanazarova, Ulugbek Komiljonovich Urinov

Technical science and innovation

Polymerization processes generate considerable amounts of liquid secondary by-products, which are often underutilized despite their significant chemical potential. Addressing the need for sustainable resource use, this study aims to develop a technological method for converting these by-products into valuable aliphatic amines. The experimental approach involved the pre-treatment of liquid polymerization by-products through fractional distillation to isolate C3–C10 fractions, followed by catalytic amination using Raney nickel under controlled temperature (160°C) and pressure (12 atm) conditions. Analytical methods including gas chromatography-mass spectrometry (GC-MS) and Fourier-transform infrared spectroscopy (FTIR) were employed to characterize the reaction products. The results demonstrated the successful formation of …

Analysis Of Inhibitor Supply Control Systems To Prevent Hydrate Formation In A Low-Temperature Gas Separation Unit And A Method For Solving The Problem, Shakhzod Nurmuhammadovich Amirov Mr, Erkin Xxx Uljayev

Technical science and innovation

The article examines and analyzs patents, published scientific works, and currently used scientific and practical methods and devices for regulating the parameters of the low-temperature separation process in production. However, the conducted analysis showed that one of the main causes of hydrate formation in the device is the lack of continuous comprehensive control over parameters such as the pressure of the inhibitors supplied to the injectors at each stage and the moisture content of the total gas, i.e., the moisture content of the total gas at the system inlet, the gas temperature at the device outlet, and the pressure and …

Design, Fabrication, And Testing Of A Pdms-Based Nanochannel Using Nano Embossing, Cooper James Haskamp

Graduate Theses and Dissertations

DNA sequencing has become increasingly important in the field of biomedical research and clinical applications. Currently, the most well-established sequencing technique is ‘Sequencing by Synthesis’ with accuracy in the range of 99.2% to 99.74% and sequencing lengths of only 300 base pairs. Sequencing by Synthesis is a lab-based method that requires expensive equipment and fast parallel computing. It is not suitable for portable, on-site applications. A new technique known as ‘nanopore’ was developed to meet these requirements. Nanopore is an electrical sequencing method that relies on the translocation of a DNA molecule through a nanoscale pore, where the blockage current …

Compound Role Of Using Advanced Materials And Design Procedures On Improving The Performance Of Baghdad Buildings Facades, Abeer Qasim Jbur

Al-Esraa University College Journal for Engineering Sciences

The research idea addresses improving the thermal performance of buildings in Baghdad by selecting and employing facade materials to reduce heat gain and energy consumption associated with cooling in a hot-dry climate. The study discusses the pivotal role of facade materials in interacting with solar radiation, heat transfer, and inward thermal transmittance, as well as their capacity to store and release heat in ways that maintain thermal comfort within architectural spaces and reduce reliance on mechanical cooling systems. A range of traditional materials such as stone, earth, and concrete is presented alongside modern materials like high-performance glass and thermal storage …