Aviation Commons^™

Quantum Safety Metrics Framework For Commercial Unmanned Aircraft Operators, Tracy L. Lamb, Nathan A. Phillips, Trong Van Nguyen

International Journal of Aviation, Aeronautics, and Aerospace

Commercial unmanned aircraft systems continue to increase in applications and diversity; however, mishaps and accidents erode safety, investment return, and efficiency. Most unmanned aircraft accidents are preceded by leading indicators; the ability to forecast and quantify these may provide increased safety and profitability. This mixed-method research study used a non-experimental parallel convergence approach with multiple instruments, multiple-case study n = 22, and one exemplar case design to develop a quantum safety metric program. This study used a combination of previously validated methods as development instruments, including; the HFACS, STAMP, 'Sierra Scale,' and Accident Prevention Effort equations. The study extended the …

Helicopter Shaft Heating Parameters For Polyamide-11 Coating, Selim Kevran Ph.D, Uğur Ati̇ci̇

International Journal of Aviation, Aeronautics, and Aerospace

In this study, the heating parameters required for polyamide-11 (P11) coating of the helicopter shaft were investigated. The torsion value created by the force applied to the middle of the helicopter's shaft is measured. Heating before coating affects the torsion value of the shaft. A new heating mechanism has been designed to cover the shaft surface without changing the torsion value of the shaft. Thus, the coating surface is left inside the furnace and the torsion measurement area outside of the furnace. Taguchi method was used to determine heating parameters such as furnace type, initial temperature and heating time. The …

The Effects Of Aircraft Use And Available Repar Spares On Aircraft Sortie Generaiton: A Long-Duration Logistical Wargaming Simulationtool, Nathaniel M. Choo

Theses and Dissertations

A long-duration logistical wargame simulation tool that can provide quick insights into the daily aircraft availability and the daily number of missions accomplished for a variety of operational scenarios is developed. This simulation tool is designed to be a stepwise wargaming support tool for adjudication within long-duration logistical wargames and provides the user many capabilities including, but not limited to, the ability to have multiple bases and types of aircraft. Additionally, the user has the ability to control types of part failures, control parts availability, control maintenance capabilities, and control number of mission scheduled. Finally, the user can account for …

3d Printing For Solving Part Obscolescence, Ayman G. Alqarni

Theses and Dissertations

The purpose of this research was to highlight the issue of parts obsolescence and to highlight the possibility of using alternative methods to overcome parts shortage. Specifically, this thesis sought to answer the research question: is the three-dimensional printing technology (3D) an applicable approach to overcome part obsolescence. The research question was answered through data research and survey analysis. Notwithstanding, the diminished manufacturing sources and material shortages (DMSMS) management and other existing approaches, such as forecasting, contracting, and reverse engineering (RE), were discussed briefly in the literature review and profoundly in chapter IV to differentiate among applicable existing solutions toward …

Gender Differences And Cockpit Design, Susan Archer, Heidi Brewer, Stacie Fain, Stephanie Smith

Student Works

The design project reported in this paper examined female pilots’ experiences with how well or poorly cockpit design allowed them to safely accomplish their flying missions. The general aviation aircraft cockpit is not designed for female pilots, often causing them to find ways to adapt to the cockpit in order to operate the aircraft safely. Two primary focal areas for adaptations address issues with accessibility of controls and “viewability” inside and outside the cockpit. The design team used a Situation Awareness-Oriented Interface Design (SAOD) approach in preparing cockpit design recommendations for general aviation aircraft that would accommodate female pilots.

Mc80: Quantifying Effect Of Fleet Health On Sortie Execution In F-16 Fleet, Kyle R. Gladney

Theses and Dissertations

By order of the Secretary of Defense, all of the US Air Force's F-16 units were tasked to improve their fleet health to a Mission Capability (MC) rate of 80 percent, as part of a Department of Defense-wide push to make its Critical Aviation Platforms, and the units that employ them, more ready and lethal. This study uses historical fleet health and sortie execution data captured from LIMS-EV (Weapon System Viewer, 2020) to create a multiple regression model that quantifies the value of increased fleet health, defined as either MC rate or Aircraft Availability (AA) rate, in terms of increasing …

Predicting Upper Atmospheric Weather Conditions Utilizing Long-Short Term Memory Neural Networks For Aircraft Fuel Efficiency, Garrett A. Alarcon

Theses and Dissertations

Aviation fuel is a major component of the Air Force (AF) budget, and vital for the core mission of the AF. This study investigated the viability of LSTMs to increase the accuracy of deterministic NWP models, while also investigating the ability to reduce model generation time. Increased forecast accuracy for wind speeds could be implemented into existing flight path models to further increase fuel efficiency, while reduced modeling times would allow flight planners to generate a flight plan in rapid response situations. The most viable model consisted of an ensemble of six LSTMs trained o six coordinates. The model's error …

Providing Rational For Further Funding Additive Manufacturing Efforts In The Air Force, Trever J. Braunberger

Theses and Dissertations

Extremely long lead times for legacy aircraft replacement parts often exceed 120 days and cost 3 to 4 times the original price drives a search for alternative manufacturing methods such as additive manufacturing. Currently, the method to procuring a legacy replacement for aircraft such as the C-130 is daunting and at times, impossible. Through a comprehensive knowledge collection of organizational data the Air Force body of knowledge increases and provides actionable data to decision makers which has the potential of dramatically decreasing part wait times and procurement. The proposed, intuitive decision analysis framework mapped out in this research provides relevant …

Efficiency Analysis Of A Congested Brazilian Airport Applying Slots Optimization Control: Congonhas Airport Case, Mariana Franco B. Mendes, Rafael Roco De Araujo, Ana Paula Beck Da Silva Etges, Massoud Bazargan

International Journal of Aviation, Aeronautics, and Aerospace

The current slot allocation mechanism in Brazil, based on the International Air Transport Association (IATA) rules, and its supplementary local regulation The National Civil Aviation Agency (ANAC), displays a few issues and limitations (e.g. slot misuse, allocation inefficiencies). Such issues are particularly present in the case of busy airports that works near their maximum capacity for major parts of the day. This inefficiency problem is generated because of the complexity of slot allocation added to the limited decision support available for the Brazilian system. This study focuses on the implementation of an optimal slot model, based on IATA regulations with …

Degrader Analysis For Diagnostic And Predictive Capabilities: A Demonstration Of Progress In Dod Cbm+ Initiatives, William Baker, Steven Nixon, Jeffrey Banks, Karl Reichard, Kaitlynn Castelle

Engineering Management & Systems Engineering Faculty Publications

This paper presents a modified reliability centered maintenance (RCM) methodology developed by The Applied Research Laboratory at The Pennsylvania State University (ARL Penn State) to meet challenges in decreasing life cycle sustainment costs for critical Naval assets. The focus of this paper is on the requirements for the development of the on-board Prognostics and Health Management (PHM) system with a discussion on the implementation progress for two systems: the high pressure air compressor (HPAC), and the advanced carbon dioxide removal unit (ACRU). Recent Department of Defense (DoD) guidance calls for implementing Condition Based Maintenance (CBM) as an alternative to traditional …

Suborbital Payload Testing Aboard Level 3 Rocket Research Platform, Pedro Llanos, Sathya Gangadharan, Nikita Amberkar, Isachi Halphen, Melisa Mastroliberti, Michelle Munasinghe

Publications

Embry-Riddle Aeronautical University (ERAU) has launched several suborbital scientific payloads aboard Blue Origin’s New Shepard in 2017 and 2019. Students continue gaining hands-on experience in rocket design and construction, and payload integration and testing of future and more mature payloads to be launched into space. A Level 3 Rocket is being designed and developed at ERAU to serve as a scaled-down model research platform for launching and testing of payloads that will be later flown in commercial suborbital platforms such as Blue Origin’s New Shepard and PLD space Miura 1 rockets. Computer simulations were conducted to calculate the key parameters …

Uas For Public Safety Operations: A Comparison Of Uas Point Clouds To Terrestrial Lidar Point Cloud Data Using A Faro Scanner, Joseph S. Cerreta, Scott S. Burgess, Jeremy Coleman

International Journal of Aviation, Aeronautics, and Aerospace

Unmanned Aircraft Systems (UAS) can be useful tools for public safety agencies during crime or vehicle accident scene investigations if it can provide value to the resource-constrained agency. The speed of data collection, while minimizing first responder risk, while sustaining an acceptable level of accuracy and precision compared to other tools is where the agency may find value. During a recent homicide investigation in Florida, a UAS provided saved 81% in law enforcement labor hours with an acceptable level of accuracy compared to traditional methods. The purpose of this research was to compare UAS to determine if there were differences …

Effects Of Musical Ability On Flight Planning, Situational Awareness, And Flight Path Deviations, Andrew P. Henry

Doctoral Dissertations and Master's Theses

Numerous studies have been conducted on music education and the benefits that learning an instrument has on the brain. However, there is little research that connects a pilot’s ability to play an instrument to a pilot’s ability to fly an airplane. When learning an instrument, students learn non-musical abilities, such as executive functions, which may correspond with the skills necessary to be a good pilot. The purpose of this study was to find a relationship between learning a musical instrument and pilot performance, specifically related to flight planning, situational awareness, and flight path deviations. This study was a quasi-experimental design …

An Agent Based Model Of Passenger Boarding For Examining Commercial Aircraft Boarding Strategies, Frank W. Ciarallo, Raymond R. Hill, Kerry K. Ward

Faculty Publications

We use an agent-based simulation methodology to study airline passenger boarding using measures that reflect both the customer experience and airline efficiency perspective. This approach supports exploration of models of actual aircraft used in practice and detailed modeling of passenger dynamics. This paper discusses the modeling approach and a set of experiments comparing several boarding strategies from practical settings as well as the literature.

Extreme Altitude Search And Rescue Helicopter, Matthew J. De Sieno, Anthony Chavarria, David Stuver, Zach Boss

Senior Design Project For Engineers

The goal of this design was to develop an extreme altitude rescue helicopter capable of retrieving hikers stranded on top of Mount Everest. Using the Eurocopter AS350 as a baseline, a conceptual model was produced that is fully capable of hovering and delivering forward flight at the desired altitude of 8,848 meters. Combined blade element momentum theory, proper airfoil selection, and forward flight calculations were utilized in order to optimize the rotor for the given flight conditions on top of Mount Everest. Conceptual fluid dynamics and CAD modeling aided in the process of visually designing the fuselage and rotor. Not …

A Statistical Approach For Commercial Space Vehicle Integration Into The National Airspace System, Christopher Hays, Daniel Chu, Pedro Llanos

Space Traffic Management Conference

This paper explores commercial space vehicle (CSV) suborbital flight trajectories in the temporal and spatial domains for CSV integration into the National Airspace System. The research data was collected via the Suborbital Space Flight Simulator (SSFS) housed in the College of Aviation at Embry-Riddle Aeronautical University - Daytona Beach campus, and analyzed using an original MATLAB data analytics tool. This study primarily focuses on statistical trends observed in previously simulated flights supported by three Project PoSSUM (Polar Suborbital Science in the Upper Mesosphere) campaigns comprised of 34 flights and 19 control flights, and to identify relevant milestones in the CSV …

Enhancing Suborbital Science Through Better Understanding Of Wind Effects, Pedro Llanos, Diane Howard

Space Traffic Management Conference

This paper highlights the importance of understanding some key factors, such as winds effects, trajectory and vehicle parameters variations in order to streamline the space vehicle operations and enhance science in the upper mesosphere at about 85 km. Understanding these effects is crucial to refine current space operations and establish more robust procedures. These procedures will involve training new space operators to conduct and coordinate space operations in class E above FL600 airspace within the Air Traffic Organization (ATO).

Space vehicles such as Space Ship Two can spend up to 6 minutes in class E airspace above FL600 after launch. …

Effects Of A Hand Luggage Guiding System On Airplane Boarding Time And Passenger Experience, Mirte Vendel, Sagar Dangal, Jessica Coppens, Suzanne Hiemstra-Van Mastrigt, Peter Vink

International Journal of Aviation, Aeronautics, and Aerospace

This research investigates whether a hand luggage guiding system in overhead bins decreases boarding time and improves boarding experience during aircraft boarding process. A guiding system was developed which allocates and displays the passengers luggage space in the overhead bin. The allocated space is guided by a light strip in front of the display that blinks when a passenger comes close to their allocated luggage space. This system was tested in a Boeing 737 test fuselage. Compared to regular boarding, a boarding time reduction of 16 to 23 seconds was estimated using the hand luggage guiding system in groups of …

Global Aviation System: Towards Sustainable Development, Marina P. Bonser Dr.

International Journal of Aviation, Aeronautics, and Aerospace

Aviation around the world has integrated into a global system. As the integration process continues, more aspects and levels of it need to be lead towards the sustainable development of the whole system via advancing strategic management, global communication proficiency, and technological expertise. It becomes essential to enrich global language (English) proficiency with cross-cultural communication competence not only for communication in the air but also for airport security, passenger and cargo services, aircraft and equipage engineering, building, and maintenance. Nowadays lower levels of management need more advanced strategic thinking and problem solving skills, and higher levels of management need global …

Effects Of Exit Doors And Number Of Passengers On Airport Evacuation Effeciency Using Agent Based Simulation, Jie Chen, Dahai Liu, Sirish Namilae, Sang-A Lee, Jennifer E. Thropp, Younho Seong

International Journal of Aviation, Aeronautics, and Aerospace

Many factors determine the efficiency of evacuation at an airport during emergencies. These factors are very complicated and many times, unpredictable. The Federal Aviation Administration provides numerous advisory circulars and regulations for managing airport evacuation. However, a thorough literature review suggests that research on airport evacuation is still very limited. A study was designed to simulate an airport evacuation to address this problem. This study selected a local certificated airport in the United States for this purpose. We developed and validated a situation model using AnyLogic to investigate evacuation time at this airport. Using different variables, such as the number …

Aircraft Interior Design And Satisfaction For Different Activities; A New Approach Toward Understanding Passenger Experience, Golnoosh Torkashvand, Lucas Stephane, Peter Vink

International Journal of Aviation, Aeronautics, and Aerospace

Among airlines and aircraft manufacturers there is much attention for passenger experience. However, there is not much literature on how the activities of passengers can be supported by the aircraft interior. The current study focuses on the need finding and requirements analysis of flight passengers. Twenty-three activities were defined based on retrospective interviews and brainstorming sessions. Respondents were asked to rate their overall perception related to the importance of each of those 23 activities on a Linkert scale, from “not at all important” to “extremely important”. On a separate question they were also asked to rate their overall satisfaction by …

Landing-Gear Impact Response: A Non-Linear Finite Element Approach, Tuan H. Tran

UNF Graduate Theses and Dissertations

The primary objective of this research is to formulate a methodology of assessing the maximum impact loading condition that will incur onto an aircraft’s landing gear system via Finite Element Analysis (FEA) and appropriately determining its corresponding structural and impact responses to minimize potential design failures during hard landing (abnormal impact) and shock absorption testing. Both static and dynamic loading condition were closely analyzed, compared, and derived through the Federal Aviation Administration’s (FAA) airworthiness regulations and empirical testing data.

In this research, a nonlinear transient dynamic analysis is developed and established via NASTRAN advanced nonlinear finite element model (FEM) to …

Evaluating Annual Fixed Wing Maintenance Costs, Kirsten Bunecke, Edward D. White, Jonathan D. Ritschel, Brett A. Bush

Faculty Publications

This article serves two purposes: first, to empirically model the annual percentage increase of operations and support (O&S) costs for fixed wing aircraft; and second, to place into the archival realm another reference for other researchers to consider when investigating other O&S topics. For this study of 21 different airframes grouped together at the Mission- Design Series (MDS), maintenance subcategories 3.1 Consumable Materials and Repair Parts, 3.2 Depot Level Repairables (DLR), and 3.4 Depot Maintenance accounted for an average 91.5% of annual organic maintenance costs. For contractor-maintained MDS, subcategory 3.7, Contractor Logistics Support (CLS) accounted for 96.6% of annual maintenance …

Effects Of Lighting And Noise On Performance And Situation Awareness In An Air Traffic Control Task, Saralee Pruksaritanon, Andrew Dattel Ph.D., Steven Hampton Ed.D.

National Training Aircraft Symposium (NTAS)

Work environment influences an individual’s performance and situation awareness (SA). This study aims to investigate the effects of lighting and noise levels on performance and situation awareness in an air traffic control (ATC) task. These two variables are important in the domain of ATC because the task requires an individual to receive and process information both visually and auditorily. The results are useful for designing air traffic control rooms, which are set differently among different air navigation service providers. The subjects are 16 students majoring in Air Traffic Management (ATM) at Embry-Riddle Aeronautical University (ERAU) – Daytona Beach, FL. The …

Ranking Of Human Senses In Relation To Different In-Flight Activities Contributing To The Comfort Experience Of Airplane Passengers, Joyce Bouwens, Suzanne Hiemstra-Van Mastrigt, Peter Vink

International Journal of Aviation, Aeronautics, and Aerospace

Bubb, Bengler, Grünen, and Vollrath (2015) identified six environmental comfort factors and ordered them from most important to least important (smell, light, vibrations, sound, climate and anthropometry). This paper attempts to verify whether this suggested order of comfort-related factors also applies to the expectations of aircraft passengers. For this purpose, two studies were carried out. First, a survey was conducted among 183 aircraft passengers between 19 and 64 years old. In this survey, respondents were asked to rank six comfort factors by selecting the most important factor from 15 pairs of factors (e.g. light versus smell). The respondents indicated anthropometry …

Effect Of Anthropometric Variability On Middle-Market Aircraft Seating, Tara C. Sriram

International Journal of Aviation, Aeronautics, and Aerospace

A middle-of-market aircraft, or MoMA, is defined as an aircraft capable of flying 180-250 passengers without refueling for 2,300-5,800 miles(~2,000-5,000 nautical miles). As the name suggests, middle-of-market aircraft are positioned in between the market segments served by narrow body (single-aisle) and wide body (twin-aisle) aircraft. This paper presents the findings of a study on the effect of anthropomorphic variability on economy class seating on middle-market aircraft currently in service. The study found that among 130 middle-market LOPAs, the mean seat pitch was greater for US airlines than for Asian airlines. Furthermore, the sampled Asian airlines had a higher preference …

Assessment And Comparison Of Aviation Manufacturing Industries Throughout Mexico And Brazil, Omar E. Morsi, Kelly A. Whealan-George, Aaron D. Clevenger

International Journal of Aviation, Aeronautics, and Aerospace

This literature review serves to provide insight and understanding in regards to the evolving aviation manufacturing industry throughout the globe and more specifically, Mexico and Brazil. Increased demand for aircraft units both in the commercial and private sectors have led to unprecedented expansions in aircraft manufacturing across the industry. In order to illuminate certain potentials and current growth levels of such industries, this review will delve into an array of information and specifications in regards to economic, political, and cultural influences throughout both Mexican and Brazilian markets respectively. In conclusion, the review will identify the transformation of an aviation manufacturing …

Unmanned Aerial Systems: Research, Development, Education & Training At Embry-Riddle Aeronautical University, Michael P. Hickey

Publications

With technological breakthroughs in miniaturized aircraft-related components, including but not limited to communications, computer systems and sensors, state-of-the-art unmanned aerial systems (UAS) have become a reality. This fast-growing industry is anticipating and responding to a myriad of societal applications that will provide new and more cost-effective solutions that previous technologies could not, or will replace activities that involved humans in flight with associated risks.

Embry-Riddle Aeronautical University has a long history of aviation-related research and education, and is heavily engaged in UAS activities. This document provides a summary of these activities, and is divided into two parts. The first part …

An Attribute Agreement Method For Hfacs Inter-Rater Reliability Assessment, Teddy Steven Cotter, Veysel Yesilbas

Engineering Management & Systems Engineering Faculty Publications

Inter-rater reliability can be regarded as the degree of agreement among raters on a given item or a circumstance. Multiple approaches have been taken to estimate and improve inter-rater reliability of the United States Department of Defense Human Factors Analysis and Classification System used by trained accident investigators. In this study, three trained instructor pilots used the DoD-HFACS to classify 347 U.S. Air Force Accident Investigation Board (AIB) Class-A reports between the years of 2000 and 2013. The overall method consisted of four steps: (1) train on HFACS definitions, (2) verify rating reliability, (3) rate HFACS reports, and (4) random …

Equivalency Analysis Of Sidestick Controller Modes During Manual Flight, Alex Rummel

Electronic Theses and Dissertations

Equivalency analysis is a statistical procedure that can enhance the findings of an analysis of variance in the case when non-significant differences are identified. The demonstration of functional equivalence or the absence of practical differences is useful to designers introducing new technologies to the flight deck. Proving functional equivalence is an effective means to justify the implementation of new technologies that must be "the same or better" than previous technology. This study examines the functional equivalency of three operational modes of a new active control sidestick during normal operations while performing manual piloting tasks. Data from a between-subjects, repeated-measures simulator …