Aviation Commons^™

Comparative Analysis Of Small Unmanned Aircraft Systems Operations Manuals, Stephen M. Cigal

Student Works

With over 100,000 remote pilots in the United States, individuals and companies are rapidly incorporating unmanned aircraft system technologies into their everyday life and businesses models. The companies that use these technologies must comply with federal and state regulations in order to maintain a safe environment to operate. These operations must also be accepted by the general public. Since the FAA regulations for small unmanned aircraft systems (sUAS) went into effect in 2016, supplemented by additional state and/or local requirements, some companies have generated operations manuals (OM) to ensure consistent, safe flight that meets these requirements. By analyzing the OM’s …

Keeping Your Distance: The Science Of Turns-Around-A-Point And Ground Reference Maneuvers, Nihad E. Daidzic

Aviation Department Publications

Ground reference maneuvers are more important than you may think. Frequently regarded as unimportant or boring, ground reference maneuver training is often limited to a few minutes of flight instructor demonstration and brief student practice.

Investigation Into The Effects Of Blade Tip Twist On Noise Reduction For A Naca 0012 Rotor Blade, Uyen T. Sou

McNair Research Journal SJSU

The advancement of the urban air mobility concept is heavily dependent on the public acceptance of the aircraft vehicles used for air taxis. The importance of the perception of noise by humans is crucial to the passing of legislation and proposals working to implement the new transport system. The investigation into how the noise perception can be reduced is vital to the success of the personal air travel industry. The air taxi design has been geared towards the rotorcraft models. Therefore, the investigation into the rotor blade designs is necessary because, similar to helicopters, the main component in noise generation …

Modifying Casting Parameters To Improve The High Temperature Ductility Of Investment Cast Nickel-Based Superalloy Pwa 1455, Lars Alexander Hedin, Cole Magnum Introligator

Materials Engineering

PCC Structurals, an industry leader in superalloy investment castings, has observed inconsistencies in the stress rupture performance of polycrystalline nickel-based superalloy PWA 1455. PCC has changed their casting parameters to reduce the thermal gradient during cooling but have been unable to correlate these changes with an increase in stress rupture elongation. Metallographic examination of past samples indicated microstructures composed of non- equiaxed dendritic grains with mean diameter of .021 inches along the test axis. A similar study on polycrystalline superalloys has indicated that excessive superheat temperatures above the liquidus can result in large grains identical to those observed, limiting the …

An Afternoon With General Thomas P. Stafford, Stafford Air & Space Museum

Programs

An Afternoon with General Thomas P. Stafford

Sunday, May 19th, 2019 at 2:00 P.M. at the Weatherford High School Performing Arts Center.

Unless stated otherwise within this repository collection, all materials are shared under the following Creative Commons license: [Creative Commons Attribution-NonCommercial 4.0 International License].

Apollo 10, 50th Anniversary Gala, Stafford Air & Space Museum

Programs

The Apollo 10 50th Anniversary Gala was held on May 18th, 2019 at the Stafford Air & Space Museum in Weatherford, Oklahoma.

Unless stated otherwise within this repository collection, all materials are shared under the following Creative Commons license: [Creative Commons Attribution-NonCommercial 4.0 International License].

Subscale Mars Colonization Mission, Cameron J. Lamack, James Lumsden, Sean Nevin, Donner Schoeffler, Riley Evers, Alexandra Poulakos, Skyler Tan, Anthony Keba, Siraj Zaman, Ali Altamimi, Anthony Modica

Honors Thesis

The team will compete in the SAE (Society of Automotive Engineers) Aero Design West Advanced Class competition, held 5-7th April 2019 in Van Nuys, California. The team will work to develop, through research, design, optimizational trade studies, and manufacturing, a system for the deployment of parasitic aircraft, as well as payload. The system will consist of a primary fixed-wing aircraft, parasitic autonomous gliders, a real-time altitude data acquisition system, as well as both static and releasable payload. The deployable gliders must navigate autonomously to a targeting area on the ground without any on-board propulsion. The releasable payload, which will consist …

Development Of A Multi-Probe Kelvin Scanner Device For Industrially-Relevant Characterization Of Surface-Activated Carbon Fiber Reinforced Thermoplastic Composites, Kirby Simon

McKelvey School of Engineering Graduate Student Theses & Dissertations

Carbon fiber reinforced thermoplastic (CFRTP) composites are becoming increasingly attractive materials in manufacturing due to their lightweight nature, mechanical strength, and corrosion resistance. Surface activation of these materials is usually required during processing to increase the bond strength of assemblies (aerospace and automotive industries) or improve adhesion with implants (biomedical industry). Industrially-relevant, nondestructive quality control methods for assessing the activation state of these materials do not currently exist, however. Applying principles discovered through the use of scanning probe microscopy, a multiple-probe Kelvin scanning (MPKS) device has been developed that can assess the uniformity of the activation state of plasma-treated CFRTP …

The Changing Face Of Airmanship And Safety Culture Operating Unmanned Aircraft Systems, Tracy Lamb

Student Works

The notion of using drones for commercial purposes has evolved in the past 5 years from the initial “boom” of excitement around this, somewhat of a novelty and curiosity, to more calculated and sophisticated use of unmanned aircraft systems (UAS), or drones. In the hands of true professionals, drones can offer highly efficient and profitable solutions for industrial, and commercial inspections and other data capturing tasks. The appetite for safe and efficient collection of data is a changing face of safety cultures and how teams and individuals apply airmanship principles, and how inspection crew and UAS crew interact. UAS are …

Extreme Altitude Search And Rescue Helicopter, Matthew J. De Sieno, Anthony Chavarria, David Stuver, Zach Boss

Senior Design Project For Engineers

The goal of this design was to develop an extreme altitude rescue helicopter capable of retrieving hikers stranded on top of Mount Everest. Using the Eurocopter AS350 as a baseline, a conceptual model was produced that is fully capable of hovering and delivering forward flight at the desired altitude of 8,848 meters. Combined blade element momentum theory, proper airfoil selection, and forward flight calculations were utilized in order to optimize the rotor for the given flight conditions on top of Mount Everest. Conceptual fluid dynamics and CAD modeling aided in the process of visually designing the fuselage and rotor. Not …

Control Failures And How To Deal With It, Nihad E. Daidzic

Aviation Department Publications

FAA Safety Seminar (GL1591497) held at Minnesota State University, Mankato Wiecking Center Auditorium at 18:00 CST on Thursday, April 18, 2019.

Multi-Path Automatic Ground Collision Avoidance System For Performance Limited Aircraft With Flight Tests: Project Have Medusa, Kenneth C. Gahan

Theses and Dissertations

A multi-path automatic ground collision avoidance system (Auto-GCAS) for performance limited aircraft was further developed and improved to prevent controlled flight into terrain. This research includes flight test results from the United States Test Pilot School's Test Management Project (TMP) titled Have Multi-Path Escape Decisions Using Sophisticated Algorithms (MEDUSA). Currently, the bomber and mobility air- craft communities lack an Auto-GCAS. The F-16 Auto-GCAS was proven successful for fighter-type aircraft with seven aircraft and eight lives saved from 2014 to 2018. The newly developed and tested Rapidly Selectable Escape Trajectory (RSET) sys- tem included a 5-path implementation which continuously updated at …

Simulation And Piloted Simulator Study Of An Automatic Ground Collision Avoidance System For Performance Limited Aircraft, James D. Carpenter

Theses and Dissertations

The F-16 Automatic-Ground Collision Avoidance System (Auto-GCAS) has been a resounding success since implementation in Nov 2014, saving 8 pilots and 7 aircraft from Controlled Flight into Terrain (CFIT). However, there is no implemented Auto- GCAS for "heavy" performance limited aircraft. This research endeavors to expand on the success of F-16 Auto-GCAS to other aircraft in the Air Force inventory such as the C-130, C-17, and B-1. MIL-STD-1797 classifies performance limited aircraft as large, heavy, and low to medium maneuverability. Using a stitched Learjet-25D model (LJ-25D), an Auto-GCAS algorithm was developed to predict multiple escape-maneuver trajectories, compare these paths to …

Incidence Of An Astronaut Not Sealing The Pressure Garment Visor On Reentry, Cameron M. Smith, Trent Tresch

Journal of Human Performance in Extreme Environments

Audiovisual records of a Project Mercury pilot’s activities during an orbital flight indicate that his visor was left open during reentry and descent to the sea surface, phases of flight during which cabin pressure loss was to be mitigated by suit pressurization; however, the suit could not have been pressurized with the visor open. Thus, for a presently unknown reason, a critical safety step—sealing the visor and making a pressure suit integrity test before reentry—was overlooked in this flight. Later, Space Shuttle flights were carried out with visors unsealed for much of the launch and landing phases, with the false …

A Statistical Approach For Commercial Space Vehicle Integration Into The National Airspace System, Christopher Hays, Daniel Chu, Pedro Llanos

Space Traffic Management Conference

This paper explores commercial space vehicle (CSV) suborbital flight trajectories in the temporal and spatial domains for CSV integration into the National Airspace System. The research data was collected via the Suborbital Space Flight Simulator (SSFS) housed in the College of Aviation at Embry-Riddle Aeronautical University - Daytona Beach campus, and analyzed using an original MATLAB data analytics tool. This study primarily focuses on statistical trends observed in previously simulated flights supported by three Project PoSSUM (Polar Suborbital Science in the Upper Mesosphere) campaigns comprised of 34 flights and 19 control flights, and to identify relevant milestones in the CSV …

Enhancing Suborbital Science Through Better Understanding Of Wind Effects, Pedro Llanos, Diane Howard

Space Traffic Management Conference

This paper highlights the importance of understanding some key factors, such as winds effects, trajectory and vehicle parameters variations in order to streamline the space vehicle operations and enhance science in the upper mesosphere at about 85 km. Understanding these effects is crucial to refine current space operations and establish more robust procedures. These procedures will involve training new space operators to conduct and coordinate space operations in class E above FL600 airspace within the Air Traffic Organization (ATO).

Space vehicles such as Space Ship Two can spend up to 6 minutes in class E airspace above FL600 after launch. …

Evaluation Of Unmanned Aircraft Flying Qualities Using A Stitched Learjet Model, Patrick M. Callaghan

Theses and Dissertations

In recent years, military UAVs have taken over missions that were too dull, dirty, or dangerous for manned aircraft. The increased demand has led to a build-fly-fix-fly development mentality, plaguing the early lifecycle with staggering mishap rates. Currently, MIL-STD-1797 lists flying qualities for UAVs as TBD, and the standards for manned fixed wing are inadequate when applied to UAVs. In an effort to expand the database of UAV flying qualities, an analysis was completed on a Simulink model of an LJ-25D developed from Calspans Variable Stability System aircraft at the United States Test Pilot School. Three maneuvers were simulated: (1) …

W&B Problems For Far/Cs 25 Airplanes Tutorial, Nihad E. Daidzic

Aviation Department Publications

Weight and Balance (W&B) computations are essential step in ensuring that the aircraft (in this case FAR/CS 25 Transport-category airplanes) is properly loaded with its Center of Mass (CM) of Center of Weight/Gravity (CG) in the proper range.

Low Level Turbulence Detection For Airports, Anthony O' Connor, Derek Kearney

International Journal of Aviation, Aeronautics, and Aerospace

Abstract—— Low level wind shear and turbulence present a serious safety risk to aircraft during the approach, landing and take-off phases. Despite many advances in on-board and ground based warning systems. Wind shear remains a formidable force that coupled with a microburst can overpower any aircraft. Aviation reports have concluded that pilots need to have improved information in relation to tailwinds, wind shear and wind variations on approach and during the landing phases. Low level wind shear continues to cause disruption, delays and contribute to aircraft crashes. As recently as 2016, two Boeing aircraft crashed while attempting a Go-around …

Beyond 2020 Nextgen Compliance: Human Factors And Cognitive Loading Issues For Commercial And General Aviation Pilots, Mark D. Miller, Sam Holley

Publications

As previously identified by the authors, digitized flight decks have realigned SHELL model components and introduced cognitive overload con­cerns. Considering changes from implementing Next Generation air traffic management requirements in 2020, the authors assess digitized interfaces associated with cockpit displays of information integral to performance based navigation and similar operations. Focus is placed on Automatic Dependent Surveillance Broadcast, digitized communications, and expanded electronic flight bags. The ADSB (In) cockpit display will enable pilots to have flight visual awareness on aircraft, terrain, weather and hazards to flight through live satellite updates every second. Increased optical demands and cognitive loading are anticipated …

The Application Of Signal Detection Theory Principles To Aircraft Certification, John M. Maris Ph.D, Alexander V. Ilyin Ph.D

International Journal of Aviation, Aeronautics, and Aerospace

This paper presents the application of Signal Detection Theory (SDT) concepts to the certification of optional systems that provide operational or system safety benefits. The method and analysis yield quantitative requirements for the system performance that account for the risks and benefits of the potential system. This is in contrast to the standard certification approach which only focuses on Failure Conditions, and does not examine potential system benefits. A case study of an aircraft spotter on an electronic moving map illustrates that substantial safety improvements may be achieved even with the relatively low levels of software reliability associated with Commercial …

Comparison Of Fixed-Wing Unmanned Aircraft Systems (Uas) For Agriculture Monitoring, Joseph Cerreta, Kristine M. Kiernan

International Journal of Aviation, Aeronautics, and Aerospace

Florida citrus growers need inexpensive methods to observe citrus plants to detect disease and stress consistently. Health vegetation indices, such as the Normalized Difference Vegetation Index (NDVI) collected from Unmanned Aircraft Systems (UAS), can be used to identify variation in plant health. Simple-to-operate UAS may enable growers to determine within-field variation more frequently than with inspections from scouts, providing more frequent knowledge about the crop condition. This research compared two low-cost fixed-wing UAS, a $5,000 Parrot Disco Pro Ag and a $16,690 senseFly eBee, each equipped with a Parrot Sequoia multispectral camera, to determine if there were differences in the …

In-Flight Wingtip Folding: Inspiration From The Xb-70 Valkyrie, Gaétan X. Dussart, Mudassir Lone, Ciaran O'Rourke, Thomas Wilson

International Journal of Aviation, Aeronautics, and Aerospace

Wingip folding can be used to extend aircraft wingspan, allowing designers to take advantage of reduced induced drag whilst respecting ground operational limitations. Such devices can also be used in-flight for a variety of other benefits including load alleviation and flight control. The majority of in-flight folding research takes inspiration in past developments made on the XB-70 Valkyrie, which used the folding devices for stability and lift performance benefits. In this paper, the authors investigate the capabilities of the folding wingtip system and potential scaling to large civil aircraft. Manufacturing details are used to size the actuators whilst the aerodynamic …

Effects Of A Hand Luggage Guiding System On Airplane Boarding Time And Passenger Experience, Mirte Vendel, Sagar Dangal, Jessica Coppens, Suzanne Hiemstra-Van Mastrigt, Peter Vink

International Journal of Aviation, Aeronautics, and Aerospace

This research investigates whether a hand luggage guiding system in overhead bins decreases boarding time and improves boarding experience during aircraft boarding process. A guiding system was developed which allocates and displays the passengers luggage space in the overhead bin. The allocated space is guided by a light strip in front of the display that blinks when a passenger comes close to their allocated luggage space. This system was tested in a Boeing 737 test fuselage. Compared to regular boarding, a boarding time reduction of 16 to 23 seconds was estimated using the hand luggage guiding system in groups of …

Global Aviation System: Towards Sustainable Development, Marina P. Bonser Dr.

International Journal of Aviation, Aeronautics, and Aerospace

Aviation around the world has integrated into a global system. As the integration process continues, more aspects and levels of it need to be lead towards the sustainable development of the whole system via advancing strategic management, global communication proficiency, and technological expertise. It becomes essential to enrich global language (English) proficiency with cross-cultural communication competence not only for communication in the air but also for airport security, passenger and cargo services, aircraft and equipage engineering, building, and maintenance. Nowadays lower levels of management need more advanced strategic thinking and problem solving skills, and higher levels of management need global …

Double Stud Cargo Fitting Research, Alternative Cargo Clip Design And Analysis, Cemal İrfan Çalişkan, Ebubekir Koç Dr, Hamaid Mahmood Khan Dr, Mustafa Enes Bulduk

International Journal of Aviation, Aeronautics, and Aerospace

It can be said that today's civil aviation basics began to be laid in the 1950s. This date is also important as the period in which the rules are being written and at the same time, some system solutions are produced by testing the methods of cargo loading. The cargo clip used in these cargo loading systems will be the subject of our article. In this context, the development process of the clip, which started in 1953 until today, will be examined in the light of the patent applications of the period; Afterwards, alternative clip-on work to the current cargo …

Generator Design: A Study Of Optimized Airflow, Rachel Wattleworth

Williams Honors College, Honors Research Projects

The core goal of this project was to prototype, test, and evaluate a new type of fan for the Safran Electrical & Power air-cooled generators. The idea of a new fan being made for these two generators arose when they were not adhering to design requirements. A base mixed-flow fan was created to test on multiple generators. Upon creating a prototype, it will be tested to prove if it can increase the air flow, decrease temperatures, and increase power and life of the machines. They all proved to be successful and achieve the main objectives for this project. Data such …

Strategies In Developing An Aviation & Aerospace Skill Ecosystem For The State Of Telangana, India – Case Study Of Task -Telangana Academy For Skill And Knowledge, Kim Chua, Sujiv Nair, M.P Ganesh Dr.

International Journal of Aviation, Aeronautics, and Aerospace

The aviation & aerospace sector in India has been expanding and growing through partnerships and new research facilities, thereby encouraging more players to invest and optimize the manufacturing process. Improving green and fuel-efficient technologies have contributed to a steady rise in fuelling the demand for aerospace engineers.

The state of Telangana is fast emerging as a new aviation cluster with some of the country’s best-qualified engineers and technicians. The potential of the aerospace industry is immense as it continuously requires skilled technicians and engineers. Considering the precision of skill required, it is imperative that rigorous training be imparted to all …

Satellite Maintenance: An Opportunity To Minimize The Kessler Effect, Bettina M. Mrusek Dr.

International Journal of Aviation, Aeronautics, and Aerospace

Recently, there has been an emphasis on the growing problem of orbital debris. While the advantages of placing satellites into space are numerous, advances in satellite technology combined with the growth of the industry have resulted with a significant amount of debris in the orbits surrounding our planet. The harshness of the space environment has also contributed to the debris, as evidenced by the number of objects currently in orbit which are not operational. As the amount of debris grows, so too does the likelihood of collisions, ultimately culminating in the Kessler Effect. However, recent advances in propulsion, advanced navigation, …

Big Five Technologies In Aeronautical Engineering Education: Scoping Review, Ruth Martinez-Lopez

International Journal of Aviation, Aeronautics, and Aerospace

The constant demands that technology creates in aerospace engineering also influence education. The identification of the technologies with practical application in aerospace engineering is of current interest to decision makers in both universities and industry. A social network approach enhances this scoping review of the research literature to identify the main topics using the Big Five technologies in aerospace engineering education. The conceptual structure of the dataset (n=447) was analyzed from different approaches: at macro-level, a comparative of the digital technology identified by cluster analysis with the number of co-words established in 3 and 8 and, a keyword central structure …