Open Access. Powered by Scholars. Published by Universities.®

Automotive Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

2015

Discipline
Institution
Keyword
Publication
Publication Type

Articles 31 - 36 of 36

Full-Text Articles in Automotive Engineering

Designing A Heat Sink For Lithium-Ion Battery Packs In Electric Vehicles, Dylan Irvine, Evan Foreman, Christopher B. Remington, Aaron Jackson, Sam Endrizzi Jan 2015

Designing A Heat Sink For Lithium-Ion Battery Packs In Electric Vehicles, Dylan Irvine, Evan Foreman, Christopher B. Remington, Aaron Jackson, Sam Endrizzi

Williams Honors College, Honors Research Projects

This report addresses the concepts and implementation of fluid cooled heat sink designs for an electric or hybrid vehicle battery. To determine the battery’s temperature and heat flux profile, testing was performed by measuring these values at multiple locations on a lithium-ion pouch battery using heat flux sensors and thermocouples during the charge and discharge cycles of the battery. Once the data was collected and analyzed, trendlines were fit to the heat flux data then used to create equations for the heat flux profile during the discharging stage. Each equation represented a specific region on the battery geometry. Four heat …

Go to article

Modeling And Analysis Of Reactivity Controlled Compression Ignition (Rcci) Combustion, Mohammadreza Nazemi Jan 2015

Modeling And Analysis Of Reactivity Controlled Compression Ignition (Rcci) Combustion, Mohammadreza Nazemi

Dissertations, Master's Theses and Master's Reports - Open

Homogeneous Charge Compression Ignition (HCCI) and Premixed Charge Compression Ignition (PCCI) combustion strategies are promising methods for achieving low engine-out NOx and soot emissions as well as high indicated efficiency. However, these combustion strategies have difficulties with controlling the rate of heat release and lack of an adequate combustion phasing control mechanism. A dual-fuel Reactivity Controlled Compression Ignition (RCCI) combustion strategy will address these issues due to the existence of precise means for controlling the heat release rate and combustion phasing. In the RCCI strategy two fuels with different reactivity (auto-ignition characteristics, e.g., gasoline and diesel) are blended inside the …

Go to article

Binder Jet Additive Manufacturing Of Stainless Steel-Hydroxyapatite Bio-Composite, Don Suranga Dhanushka Uduwage Jan 2015

Binder Jet Additive Manufacturing Of Stainless Steel-Hydroxyapatite Bio-Composite, Don Suranga Dhanushka Uduwage

All Graduate Theses, Dissertations, and Other Capstone Projects

This study was conducted to create a bio-composite with a porous structure using the binder-jet printing additive manufacturing process. The samples were printed by changing the parameters such as layer thickness, roller speed, sintering time and sintering temperature of the X1-Lab binder jet additive manufacturing printer. The samples were printed 80% stainless steel 316 mixed with 20% Calcium Phosphate Tribasic by volume. Eight experiments were attempted to print according to the fractional factorial design of experiment. The effects of changing parameters on the mechanical properties of the new bio-composite was tested using ASTM E-09 compressive strength standards. The compression testing …

Go to article

Air Flow And Rain Water Penetration Analysis On Generator Enclosures Using Cfd Simulations, Sasanka Andawatta Kankanamge Jan 2015

Air Flow And Rain Water Penetration Analysis On Generator Enclosures Using Cfd Simulations, Sasanka Andawatta Kankanamge

All Graduate Theses, Dissertations, and Other Capstone Projects

Rain water penetration testing on power generator units requires a number of complicated procedures, requiring many resources. As such, a Computational Fluid Dynamics (CFD) tool, "FloEFD for Creo" is used to study the water penetration behavior on a OM924 diesel power generator enclosure in a computational environment. First, the three governing equations in fluid dynamics are derived and explained using simple methods. Next, behavior of rain water droplets upon impact is briefly discussed. Air velocity, volumetric flow rate and static pressure drop were measured physically in the OM924 generator enclosure. Then, a CFD model for the OM924 enclosure was developed …

Go to article

Computational Fluid Dynamics Modeling Of The Effects Of Water Injection In A Diesel Engine, Rabun Z. Wallace Jan 2015

Computational Fluid Dynamics Modeling Of The Effects Of Water Injection In A Diesel Engine, Rabun Z. Wallace

College of Graduate Studies: Theses & Dissertations

Water injection has been used in internal combustion engines for many years. It has been used to cool combustion temperatures, reduce emissions, and in some instances clean carbon buildup from the cylinder. Research has shown that the water to fuel mass ratio is most effective between 20-30%, so the upper and lower limit were used for simulations in Converge CFD. To validate the CFD model, a case without water injection was compared to experimental data from Sandia National Laboratory. The predicted in-cylinder pressure and heat release rate showed good agreement with the experimental data. Cases were run with the injection …

Go to article

Objective Predictor Metric Of Annoyance For Hydraulic Engine Mount Cavitation, John Powell Jan 2015

Objective Predictor Metric Of Annoyance For Hydraulic Engine Mount Cavitation, John Powell

College of Graduate Studies: Theses & Dissertations

Vehicle acoustics has been found to have a direct impact on customer experience. Unexpected noises play a role in this experience. Hydraulic engine mount cavitation, the noise heard from the collapse of vapor bubbles in the mount, is considered one of those unexpected noises. During the design phase of a vehicle when an unexpected noise is found there is a need for a method to quantify how much of the noise is too much. Subjective evaluations alone are not enough due to variability from engineer to engineer. An objective way needed to be developed in order to evaluate the cavitation …

Go to article

First Prev