Automotive Engineering Commons^™

Design, Fabrication And Analysis Of An Auxiliary Power Unit On A Heavy-Duty Truck To Power The Hvac Systems Of The Truck During Driver Off-Duty Conditions, Rohan Milind Kalurkar

Dissertations, Master's Theses and Master's Reports

Currently, one of the biggest challenges the world is facing is energy insufficiency. One of the contributors to energy consumption in United States are the idling semi-trailer trucks. In May 2001, President Bush issued The National Energy Policy in which he directed The Environmental Protection Agency (EPA) and Department of Transportation (DOT) to reduce the idling of trucks. This was done in order to reduce energy consumption by lowering fuel consumption and emissions coming out of semi-trailer trucks in the United States of America.

This project deals with the efforts of installing an Auxiliary Power Unit (APU) as a device …

Experimental Study, Modelling And Controller Design For An Rcci Engine, Naga Nithin Teja Kondipati

Dissertations, Master's Theses and Master's Reports

Low Temperature Combustion (LTC) has got widespread attention over the past two decades in the field of Automotive Research and Development due to it’s potential for achieving higher efficiencies with near-zero engine out NOx and soot emissions. Among all the LTC strategies Reactivity controlled compression ignition (RCCI) has shown the most promising results due to it’s precise control over combustion phasing and heat release rate. However, RCCI being a dual-fuel stratified combustion, precise control over the injection timing of direct injected fuel and in-cylinder fuel reactivity of the mixture needs to be controlled effectively in order to achieve gross indicated …

Design And Fabrication Of A Suspension Rig, Abhijith Geo Philip

Dissertations, Master's Theses and Master's Reports

Owing to its placement under the vehicle body, the suspension system is one of the parts of the vehicle which are difficult to comprehend completely, albeit being a vital component. For demonstrating the working of a suspension system, a physical model in which one can actually see the movement of all the components would be a great tool. A Mustang II independent front suspension system was purchased from Heidts Engineering Performance and a rig that can emulate some of the real world situations of vehicle suspension action was designed and fabricated. All the components are accessible and conditions like bounce, …

Modeling, Simulation And Control Of Hybrid Electric Vehicle Drive While Minimizing Energy Input Requirements Using Optimized Gear Ratios, Sanjai Massey

Dissertations, Master's Theses and Master's Reports

This project was conducted to analyze (model and simulate) and optimize an electric motor based drive system to propel a typical passenger vehicle in an urban driving environment. Although there are many HEV and EV type systems on the market today, this paper chose the Toyota Prius HEV system as a baseline using a brushless AC motor.

Although a vehicle can be driven many ways, a more standardized Urban Dynamometer Driving Schedule, UDDS, was chosen to simulate real driving conditions. This schedule is determined by the US Environmental Protection Agency, EPA, and is intended to represent the city driving conditions …

Physics-Based Modeling And Control Of Powertrain Systems Integrated With Low Temperature Combustion Engines, Mehran Bidarvatan

Dissertations, Master's Theses and Master's Reports

Low Temperature Combustion (LTC) holds promise for high thermal efficiency and low Nitrogen Oxides (NOx) and Particulate Matter (PM) exhaust emissions. Fast and robust control of different engine variables is a major challenge for real-time model-based control of LTC. This thesis concentrates on control of powertrain systems that are integrated with a specific type of LTC engines called Homogenous Charge Compression Ignition (HCCI). In this thesis, accurate mean value and dynamic cycleto- cycle Control Oriented Models (COMs) are developed to capture the dynamics of HCCI engine operation. The COMs are experimentally validated for a wide range of HCCI steady-state and …

A Quantitative Investigation Of The Water Condensation Inside Tubes Of Compact Charge Air Cooler, Robin Cash

Dissertations, Master's Theses and Master's Reports

To address the need of increasing fuel economy requirements, automotive Original Equipment Manufacturers (OEMs) are increasing the number of turbocharged engines in their powertrain line-ups. The turbine-driven technology uses a forced induction device, which increases engine performance by increasing the density of the air charge being drawn into the cylinder. Denser air allows more fuel to be introduced into the combustion chamber, thus increasing engine performance. During the compression process, the air is heated to temperatures that can cause pre-ignition, resulting in reduced engine functionality. The introduction of the charge air cooler (CAC) is therefore, necessary to extract heat from …