Automotive Engineering Commons^™

Optimized System For On-Route Charging Of Battery Electric Buses And High-Fidelity Modelling And Simulation Of In-Motion Wireless Power Transfer, Yogesh Bappasaheb Jagdale

Masters Theses

Electrifying cars, buses and trucks is an attractive means to reduce energy use and emissions, because it involves minimal restructuring of the transportation network. Transit buses drive fixed routes, minimizing driver range anxiety by properly sizing energy storage system but the major challenge to fully electrifying transit buses, is the amount of energy they consume in a day of driving. To enable a full day of operation, batteries need to be large, which is expensive and heavy. This work utilizes real-world transit bus data fed to a battery electric drive-train model to co-optimize charger locations, charger power levels, and vehicle …

Conducted And Radiated Emi Measurements Of Parallel Buck Converters Under Varying Spread Spectrum Parameters, Elena Postupalskaya, Nathan Wang

Electrical Engineering

The Conducted and Radiated EMI Measurements with Parallel Buck Converters Under Varying Spread Spectrum Parameters research senior project aims to explore the effects from Spread Spectrum Frequency Modulation (SSFM) on the input electromagnetic interference (EMI) or noise of a switching power supply, specifically with LM53601MAEVM hardware. The input EMI is important as the main input bus needs to be clean to provide a reliable source for other sensitive devices connected to it. SSFM can replace a conventional EMI filter and save weight, space, and cost. This project provides a basis in terms of the impacts of variable SSFM in simulation …

Evaluating Driving Performance Of A Novel Behavior Planning Model On Connected Autonomous Vehicles, Keyur Shah

Honors Scholar Theses

Many current algorithms and approaches in autonomous driving attempt to solve the "trajectory generation" or "trajectory following” problems: given a target behavior (e.g. stay in the current lane at the speed limit or change lane), what trajectory should the vehicle follow, and what inputs should the driving agent apply to the throttle and brake to achieve this trajectory? In this work, we instead focus on the “behavior planning” problem—specifically, should an autonomous vehicle change lane or keep lane given the current state of the system?

In addition, current theory mainly focuses on single-vehicle systems, where vehicles do not communicate with …

Control And Locomotion Of Inertially And Magnetically Actuated Multi-Scale Robotic Systems, Ehab Al Khatib

Mechanical Engineering Research Theses and Dissertations

In this research, two actuation systems were introduced, inertial and magnetic actuation. In the inertial actuation, the robot used the transfer of momentum to navigate, and this momentum could be generated by spinning masses and wheels. Recent studies in our System Laboratory proved that a wide range of inertially actuated locomotion systems could be generated. This can be achieved by using a family tree approach, starting from a very simple system, and progressively evolving it to more complex ones. The motion diversity of these robots inspired us to extend their locomotion from a macro scale to millimeter and micro scales. …

Active Drag Reduction Of Ground Vehicles Using Air-Jet Wheel Deflectors, Kaloki Nabutola

Doctoral Dissertations and Master's Theses

Seven turbulence models were used to simulate the flow within the wheelhouse of a simplified vehicle body. The performance of each model was evaluated by comparing the aerodynamic coefficients obtained using computational fluid dynamics (CFD) to data collected from wind tunnel experiments. The performance of large eddy simulation (LES) and detached eddy simulation (DES) was largely dependent on the time step and grid size to accurately resolve turbulent eddies. The standard k-e, realizable k-e, k-w, DES, and LES all trended towards a drag coefficient which was 20% lower than the experimental value. In all numerical cases, the lift coefficient was …

Hardware Security Of The Controller Area Network (Can Bus), David Satagaj

Senior Honors Theses

The CAN bus is a multi-master network messaging protocol that is a standard across the vehicular industry to provide intra-vehicular communications. Electronics Control Units within vehicles use this network to exchange critical information to operate the car. With the advent of the internet nearly three decades ago, and an increasingly inter-connected world, it is vital that the security of the CAN bus be addressed and built up to withstand physical and non-physical intrusions with malicious intent. Specifically, this paper looks at the concept of node identifiers and how they allow the strengths of the CAN bus to shine while also …

Vehicle Performance Analysis Of An Autonomous Electric Shuttle Modified For Wheelchair Accessibility, Johan Fanas Rojas

Masters Theses

Autonomous vehicles (AV) have the potential to vastly improve independent, safe, and cost-effective mobility options for individuals with disabilities. However, accessibility considerations are often overlooked in the early stages of design, resulting in AVs that are inaccessible to people with disabilities. The needs of wheeled mobility device users can cause significant vehicle design changes due to requirements for stepless ingress/egress and increased space for onboard circulation and securement. Vehicles serving people with disabilities typically require costly aftermarket modifications for accessibility, which may have unforeseen impacts on vehicle performance and safety, particularly in the case of automated vehicles. In this research, …

Vehicle Velocity Prediction Using Artificial Neural Networks And Effect Of Real-World Signals On Prediction Window, Tushar Dnyaneshwar Gaikwad

Masters Theses

Prediction of vehicle velocity is essential since it can realize improvements in the fuel economy/energy efficiency, drivability, and safety. Many publications address velocity prediction problems, yet there is a need for the understanding effect of different signals for the prediction. There are numerous new sensor and signal technologies like vehicle-to-vehicle and vehicle-to-infrastructure communication that can be used to obtain comprehensive datasets. Several references considered deterministic and stochastic approaches that use the datasets as input to determine future operation predictions. These approaches include different traffic models and artificial neural networks such as Markov chain, nonlinear autoregressive model, Gaussian function, and recurrent …

Comparison Of Optimal Energy Management Strategies Using Dynamic Programming, Model Predictive Control, And Constant Velocity Prediction, Amol Arvind Patil

Masters Theses

Due to the recent advancements in autonomous vehicle technology, future vehicle velocity predictions are becoming more robust which allows fuel economy (FE) improvements in hybrid electric vehicles through optimal energy management strategies (EMS). A real-world highway drive cycle (DC) and a controls-oriented 2017 Toyota Prius Prime model are used to study potential FE improvements. We proposed three important metrics for comparison: (1) perfect full drive cycle prediction using dynamic programming, (2) 10-second prediction horizon model predictive control (MPC), and (3) 10-second constant velocity prediction. These different velocity predictions are put into an optimal EMS derivation algorithm to derive optimal engine …

Dashboard-Mounted Driver Monitoring System, Daniel Lein, Prahlad Sarma, William Roussell, Nathan Nuñez, Elvis Manzanares

ENGS 89/90 Reports

The objective of this project is to deliver safe DMS hardware and interfacing/preprocessing software on which Toyota can run its drowsiness detection neural net. The system shall: securely house all necessary imaging, electronic, and computer hardware to output facial recognition data to the car’s computer, without data input from any other car system; obscure less than 10% of the driver’s field of view out of a standard windshield; be able to capture and process images such that the image classification neural net recognize the images, meeting the top-1 benchmark accuracy statistic across static and dynamic car-cabin lighting conditions; and meet …

Simulation And Design Tool For Supermileage Vehicle (Smv) Club Final Design Report, Kimberly Kodama, Sung Ho An, Justice Aragon

Mechanical Engineering

The purpose of this project is to create a sensitivities tool and start an optimization tool to assist the Cal Poly SMV Team in designing their vehicle, developing a driving strategy for competition, and becoming a contender in endurance events. The development of a user-friendly vehicle simulation and design tool was proposed by Professor Joseph Mello who is the club’s advisor. The SMV Team competes in endurance events such as the Supermileage competition or the Shell Eco-marathon with the goal of achieving the best mileage possible.

This report will present the research that has been conducted to understand and define …

Pedestrian Navigation Using Artificial Neural Networks And Classical Filtering Techniques, David J. Ellis

Theses and Dissertations

The objective of this thesis is to explore the improvements achieved through using classical filtering methods with Artificial Neural Network (ANN) for pedestrian navigation techniques. ANN have been improving dramatically in their ability to approximate various functions. These neural network solutions have been able to surpass many classical navigation techniques. However, research using ANN to solve problems appears to be solely focused on the ability of neural networks alone. The combination of ANN with classical filtering methods has the potential to bring beneficial aspects of both techniques to increase accuracy in many different applications. Pedestrian navigation is used as a …

Techniques To Solve Decision-Making Problems, Dilnoz Tulkunovna Muhamediyeva, Bekmuratov Fayzievich Tulkun

Chemical Technology, Control and Management

Solving decision-making problems in poorly formalized systems only with the help of deterministic and probabilistic methods is insufficient. To do this, it is necessary to widely apply the methods of hybrid intelligent systems and, especially, the methods of “soft” calculations (SoftCalculation, SoftComputing) and the directions of ComputationalIntelligence — intelligent computing technologies that are emerging on this theoretical and methodological base. An immune - fuzzy algorithm for the synthesis of fuzzy inference systems (FIS) is proposed. A two-stage adaptive FIS synthesis algorithm is described. At the first stage, the initial fuzzy parameters are clustered in order to reduce the number of …

Systemic Methodology For Cyber Offense And Defense, C. Ariel Pinto, Matthew Zurasky

Engineering Management & Systems Engineering Faculty Publications

This paper describes a systemic method towards standardization of a cyber weapon effectiveness and effectiveness prediction process to promote consistency and improve cyber weapon system evaluation accuracy – for both offensive and defensive postures. The approach included theoretical examination of existing effectiveness prediction processes for kinetic and directed energy weapons, complemented with technical and social aspects of cyber realm. The examination highlighted several paradigm-shifts needed to transition from purely kinetic-based processes and transition into the realm of combined kinetic and cyber weapons. Components of the new method for cyber weapons are cyber payload assessment, effects identification, and target assessment. The …

Quantitative Performance Assessment Of Lidar-Based Vehicle Contour Estimation Algorithms For Integrated Vehicle Safety Applications, David M. Mothershed

College of Graduate Studies: Theses & Dissertations

Many nations and organizations are committing to achieving the goal of `Vision Zero' and eliminate road traffic related deaths around the world. Industry continues to develop integrated safety systems to make vehicles safer, smarter and more capable in safety critical scenarios. Passive safety systems are now focusing on pre-crash deployment of restraint systems to better protect vehicle passengers. Current commonly used bounding box methods for shape estimation of crash partners lack the fidelity required for edge case collision detection and advanced crash modeling. This research presents a novel algorithm for robust and accurate contour estimation of opposing vehicles. The presented …

Development Of An Eco Approach And Departure Application To Improve Energy Consumption Of A Plug-In Hybrid Vehicle In Charge Depleting Mode, Brandon Narodzonek

Dissertations, Master's Theses and Master's Reports

A recent study at Michigan Technological University as part of the NEXTCAR DOE APRA-E Project was conducted to determine the potential energy savings of a plug-in hybrid electric vehicle (PHEV) equipped with various Connected and Automated Vehicle (CAV) Technologies. One aspect of this study focused on the development of an Eco Approach and Departure (Eco AnD) Application that would further reduce the energy consumed around a signalized intersection.

Many modern intersections are equipped with traffic signals that can broadcast Basic Safety (BSM), MAP, and Signal Phase and Timing (SPaT) message sets that contain intersection ID, location, current phase, and cyclic …

Energy Consumption And Savings Analysis Of A Phev In Real World Driving Through Vehicle Connectivity Using Vehicle Platooning, Blended Mode Operation And Engine Start-Stop Optimizers, Pruthwiraj Santhosh

Dissertations, Master's Theses and Master's Reports

This report presents an analysis on energy consumption of a Gen II Chevrolet Volt PHEV and its energy savings potential in Real World Driving scenarios with the help of vehicle connectivity. The research on the energy consumption analysis and optimization using connectivity will focus on four main areas of contribution which includes 1.) vehicle testing on a pre-defined drive cycle and alternative routing near the Michigan Tech campus and APS research center that is a continuation of previous students' works, 2) the energy savings potential of vehicle platooning and various vehicle platoon configurations, 3) the updating of a PHEV implementation …

Atv Dynamics And Pediatric Rider Safety, James T. Auxier Ii

Theses and Dissertations--Biomedical Engineering

It has been observed through numerous academic and governmental agency studies that pediatric all-terrain vehicle ridership carries significant risk of injury and death. While no doubt valuable to safety, the post-hoc approach employed in these studies does little to explain the why and how behind the risk factors. Furthermore, there has been no prolonged, widespread, organized, and concerted effort to reconstruct and catalog the details and causes of the large (20,000+) number of ATV-related injuries that occur each year as has been done for road-based motor vehicle accidents. This dissertation takes the opposite approach from a meta-analysis and instead examines …

Filtered-Dynamic-Inversion Control For Unknown Minimum-Phase Systems With Unknown Relative Degree, Sumit Suryakant Kamat

Theses and Dissertations--Mechanical and Aerospace Engineering

We present filtered-dynamic-inversion (FDI) control for unknown linear time-invariant systems that are multi-input multi-output and minimum phase with unknown-but-bounded relative degree. This FDI controller requires limited model information, specifically, knowledge of an upper bound on the relative degree and knowledge of the first nonzero Markov parameter. The FDI controller is a single-parameter high-parameter-stabilizing controller that is robust to uncertainty in the relative degree. We characterize the stability of the closed-loop system. We present numerical examples, where the FDI controller is implemented in feedback with mathematical and physical systems. The numerical examples demonstrate that the FDI controller for unknown relative degree …

Zips Racing Electric Can Communications, Andrew Jordan, Adam Long, Susanah Kowalewski, Rami Nehme

Williams Honors College, Honors Research Projects

The CAN protocol has been a standard of electronic communication networks of automotive vehicles since the early 2000s due to its robust reliability in harsh environments. For the 2020 competition year, the Zips Racing Electric design team will be building an entirely new, fully-electric vehicle with CAN communication implemented rather than communicating via pure analog signals. Hardware and software can be utilized to read analog electrical signals from a source, such as accelerator and brake sensors, and encode them into a digital message that meets the CAN 2.0B communication protocol standard. Likewise, software can be used to extract data from …

Human Powered Vehicle Internal Systems Design, Zachary Broadbent, Jordan Boos, Patrick Gaertner, Caleb Miner

Williams Honors College, Honors Research Projects

The objective of this design project is to redesign the seat and steering system for the Human Powered Vehicle Team. The goal of the seat design is too improve ergonomics by making it more comfortable and adjustable. In making the seat adjustable, it will be easier for drivers to achieve an optimal efficiency when pedaling. The aim for steering will be to improve the ergonomics as well as performance by analyzing steering systems in the past and evaluating how each design was successful and for what reason. Another main goal of the steering system will be improving the stability and …

Vehicle Dynamics Modeling For Autonomous Drifting And Clothoid Based Waypoint Interpolation, Shubham Vatsa

Dissertations, Master's Theses and Master's Reports

The advent of autonomous vehicles necessitates a redefinition of road safety regulations, considering a controller can possess better driving skills than an average person. The work presented here partly focuses on a vehicle dynamics model development to help imitate and control vehicle drifting maneuvers. As we see, a professional driver drifting through the traffic while keeping the car safe, it can be utilized to avoid accidents at high speeds, if required. Although drifting can produce higher yaw rates than the regular driving regime, these control capabilities have not yet been exploited in the current automotive control systems. Therefore, this report …

Hybrid Electric Vehicle Energy Management Strategy With Consideration Of Battery Aging, Bin Zhou

Dissertations, Master's Theses and Master's Reports

The equivalent consumption minimization strategy (ECMS) is a well-known energy management strategy for Hybrid Electric Vehicles (HEV). ECMS is very computationally efficient since it yields an instantaneous optimal control. ECMS has been shown to minimize fuel consumption under certain conditions. But, minimizing the fuel consumption often leads to excessive battery damage. The objective of this dissertation is to develop a real-time implementable optimal energy management strategy which improves both the fuel economy and battery aging for Hybrid Electric Vehicles by using ECMS. This work introduces a new optimal control problem where the cost function includes terms for both fuel consumption …

Sensor Fusion And Non-Linear Mpc Controller Development Studies For Intelligent Autonomous Vehicular Systems, Ahammad Basha Dudekula

Dissertations, Master's Theses and Master's Reports

The demand for safety and fuel efficiency on ground vehicles and advancement in embedded systems created the opportunity to develop Autonomous controller. The present thesis work is three fold and it encompasses all elements that are required to prototype the autonomous intelligent system including simulation, state handling and real time implementation. The Autonomous vehicle operation is mainly dependent upon accurate state estimation and thus a major concern of implementing the autonomous navigation is obtaining robust and accurate data from sensors. This is especially true, in case of Inertial Measurement Unit (IMU) sensor data. The IMU consists of a 3-axis gyro, …

Implementation Of Radial Basis Function Artificial Neural Network Into An Adaptive Equivalent Consumption Minimization Strategy For Optimized Control Of A Hybrid Electric Vehicle, Thomas P. Harris

Graduate Theses, Dissertations, and Problem Reports (ETD)

Continued increases in the emission of greenhouse gases by passenger vehicles has accelerated the production of hybrid electric vehicles. With this increase in production, there has been a parallel demand for continuously improving strategies of hybrid electric vehicle control. The goal of an ideal control strategy is to maximize fuel economy while minimizing emissions. The design and implementation of an optimized control strategy is a complex challenge. Methods exist by which the globally optimal control strategy may be found. However, these methods are not applicable in real-world driving applications since these methods require a priori knowledge of the upcoming drive …

Route Planning For Long-Term Robotics Missions, Christopher Alexander Arend Tatsch

Graduate Theses, Dissertations, and Problem Reports (ETD)

Many future robotic applications such as the operation in large uncertain environment depend on a more autonomous robot. The robotics long term autonomy presents challenges on how to plan and schedule goal locations across multiple days of mission duration. This is an NP-hard problem that is infeasible to solve for an optimal solution due to the large number of vertices to visit. In some cases the robot hardware constraints also adds the requirement to return to a charging station multiple times in a long term mission. The uncertainties in the robot model and environment require the robot planner to account …

Ethical Decision Making Behind The Wheel – A Driving Simulator Study, Siby Samuel, Sarah Yahoodik, Yusuke Yamani, Krishna Valluru, Donald L. Fisher

Psychology Faculty Publications

Over the past several years, there has been considerable debate surrounding ethical decision making in situations resulting in inevitable casualties. Given enough time and all other things being equal, studies show that drivers will typically decide to strike the fewest number of pedestrians in scenarios where there is a choice between striking several versus one or no pedestrians. However, it is unclear whether drivers behave similarly under situations of time pressure. In our experiment in a driving simulator, 32 drivers were given up to 2 s to decide which group of pedestrians to avoid among groups of larger (5) or …

Sensor Emulation With Physiolocal Data In Immersive Virtual Reality Driving Simulator, Jungsu Pak, Oliver Mathias, Ariane Guirguis, Uri Maoz

Student Scholar Symposium Abstracts and Posters

Can we enhance the safety and comfort of AVs by training AVs with physiological data of human drivers? We will train and compare AV algorithm with/without physiological data.

Self-Driving Toy Car Using Deep Learning, Fahim Ahmed, Suleyman Turac, Mubtasem Ali

Publications and Research

Our research focuses on building a student affordable platform for scale model self-driving cars. The goal of this project is to explore current developments of Open Source hardware and software to build a low-cost platform consisting of the car chassis/framework, sensors, and software for the autopilot. Our research will allow other students with low budget to enter into the world of Deep Learning, self-driving cars, and autonomous cars racing competitions.

The Challenges Facing Autonomous Vehicles And The Progress In Addressing Them, Garrett Johnson

Senior Honors Theses

Autonomous vehicles are an emerging technology that faces challenges, both technical and socioeconomic. This paper first addresses specific technical challenges, such as parsing visual data, communicating with other entities, and making decisions based on environmental knowledge. The technical challenges are to be addressed by the fields of image processing, Vehicle to Everything Communication (V2X), and decision-making systems. Non-technical challenges such as ethical decision making, social acceptance, and economic pushback are also discussed. Ethical decision making is discussed in the framework of deontology vs utilitarianism, while social acceptance of utilitarian autonomous vehicles is also investigated. Last, the likely economic impact is …