Automotive Engineering Commons^™

Design Of Real-Time Combustion Feedback System And Experimental Study Of An Rcci Engine For Control, Jayant Kumar Arora

Dissertations, Master's Theses and Master's Reports

Premixed compression ignition (PCI) technologies offer high efficiency and low emissions but are usually confined by limited operation range as well as high pressure rise and heat release rate. In this work, a more recently developed PCI mode is explored where in-cylinder blending of two fuels with different auto-ignition characteristics (diesel and gasoline) is utilized to create reactivity stratification such that heat release rate and combustion timing can be controlled. This mode has been defined as Reactivity Controlled Compression Ignition (RCCI).

As part of this thesis, the main aim is to study various parameters that can be used to control …

An Experimental Investigation Of The Effect Of Temperature And Space Velocity On The Performance Of A Cu-Zeolite Flow-Through Scr And A Scr Catalyst On A Dpf With And Without Pm Loading, Vaibhav Kadam

Dissertations, Master's Theses and Master's Reports

Abstract The heavy-duty diesel (HDD) engines use the diesel oxidation catalyst (DOC), catalyzed particulate filter (CPF) and urea injection based selective catalytic reduction (SCR) systems in sequential combination, to meet the US EPA 2010 PM and NOₓ emission standards. The SCR along with a NH₃ slip control catalyst (AMOX) offer NOₓ reduction >90 % with NH₃ slipHowever, there is a strong desire to further improve the NOₓ reduction performance of such systems, to meet the California Optional Low NOₓ Standard implemented since 2015. Integrating SCR functionality into a diesel particulate filter (DPF), by coating the SCR catalyst on the DPF, …

Competition Vehicle Based Intake Manifold Design, Joshua N. Matiash

Dissertations, Master's Theses and Master's Reports

A competitive vehicle in Formula SAE needs to be easy for unskilled drivers to extract the maximum performance from. This requires a predictable and manageable torque curve. This report details the development of an intake manifold for a Formula SAE car from a vehicle-based approach to produce this manageable and predictable torque. The current vehicle was instrumented and driven on a representative track to determine the usage of available torque. Based on these findings an ideal torque curve was chosen that favored increased torque at upper engine speed ranges and decreased torque at lower engine speed ranges. A 1-D engine …

Experimental Study, Modelling And Controller Design For An Rcci Engine, Naga Nithin Teja Kondipati

Dissertations, Master's Theses and Master's Reports

Low Temperature Combustion (LTC) has got widespread attention over the past two decades in the field of Automotive Research and Development due to it’s potential for achieving higher efficiencies with near-zero engine out NOx and soot emissions. Among all the LTC strategies Reactivity controlled compression ignition (RCCI) has shown the most promising results due to it’s precise control over combustion phasing and heat release rate. However, RCCI being a dual-fuel stratified combustion, precise control over the injection timing of direct injected fuel and in-cylinder fuel reactivity of the mixture needs to be controlled effectively in order to achieve gross indicated …

Improvement Of Diesel Engines At High Speeds Via Flexible Valve Actuation And Cylinder Deactivation, Dina M. Caicedo Parra, Gregory M. Shaver, Aswin Ramesh

The Summer Undergraduate Research Fellowship (SURF) Symposium

In the U.S fuel consumption is expected to increase over 20% from 2010 to 2020 especially in the heavy duty segment. As a consequence of the increase in production of heavy and light duty vehicles, regulations and stricter policies are being applied to the emissions of pollutants, including NOx, and soot. This study outlines strategies for using cylinder deactivation and intake valve closure (IVC) modulation to improve fuel economy and increase the rate at which NOx/soot-mitigating aftertreatment devices reach working temperatures. Effects of opening and squeezing variable geometry turbine (VGT) turbocharger were also analyzed. From the results it was observed …

The Effects Of Ivc Modulation On Modern Diesel Engines Equipped With Variable Valve Actuation At High Load And Speed, Troy E. Odstrcil, Gregory M. Shaver, Cody M. Allen

The Summer Undergraduate Research Fellowship (SURF) Symposium

Modern diesel compression engines are known for their increased durability, fuel economy and torque when compared with their spark ignition gasoline counterparts. These are some of the reasons why diesel engines are preferred in heavy duty applications such as trains and semi-trucks. During the Heavy Duty Federal Test Procedure transient drive cycle, or HDFTP, nearly 85% of the total fuel burned is at speeds greater than 2000 revolutions per minute (RPM) for the studied engine. Therefore, it is desirable to increase the fuel economy at these loads and speeds. It is hypothesized that the use of late intake valve close …

Designing A Heat Sink For Lithium-Ion Battery Packs In Electric Vehicles, Evan Foreman, Dylan Irvine, Aaron Jackson, Christopher Brandon Remington, Sam Endrizzi

Williams Honors College, Honors Research Projects

This report addresses the concepts and implementation of fluid cooled heat sink designs for an electric or hybrid vehicle battery. To determine the battery’s temperature and heat flux profile, testing was performed by measuring these values at multiple locations on a lithium-ion pouch battery using heat flux sensors and thermocouples during the charge and discharge cycles of the battery. Once the data was collected and analyzed, trendlines were fit to the heat flux data then used to create equations for the heat flux profile during the discharging stage. Each equation represented a specific region on the battery geometry. Four heat …

Design Of The University Of Akron's 2015 Fsae Electric Vehicle Braking System, Nicholas D. Galbincea

Williams Honors College, Honors Research Projects

The following report encompasses the design of the 2015 University of Akron’s FSAE formula electric braking system. The system is one based on hydraulic braking and designed for a one man performance racing vehicle. The objective of the system is to convert the kinetic energy of the vehicle into thermal energy, allowing the vehicle to decelerate optimally and safely. The design includes three major categories: calculation and evaluation of the hydraulic system in order to select calipers and master cylinders, the design of the pedal box, and the design of the rotors.

The results and findings of the proceeding report …

Designing A Heat Sink For Lithium-Ion Battery Packs In Electric Vehicles, Dylan Irvine, Evan Foreman, Christopher B. Remington, Aaron Jackson, Sam Endrizzi

Williams Honors College, Honors Research Projects

This report addresses the concepts and implementation of fluid cooled heat sink designs for an electric or hybrid vehicle battery. To determine the battery’s temperature and heat flux profile, testing was performed by measuring these values at multiple locations on a lithium-ion pouch battery using heat flux sensors and thermocouples during the charge and discharge cycles of the battery. Once the data was collected and analyzed, trendlines were fit to the heat flux data then used to create equations for the heat flux profile during the discharging stage. Each equation represented a specific region on the battery geometry. Four heat …

Computational Fluid Dynamics Modeling Of The Effects Of Water Injection In A Diesel Engine, Rabun Z. Wallace

College of Graduate Studies: Theses & Dissertations

Water injection has been used in internal combustion engines for many years. It has been used to cool combustion temperatures, reduce emissions, and in some instances clean carbon buildup from the cylinder. Research has shown that the water to fuel mass ratio is most effective between 20-30%, so the upper and lower limit were used for simulations in Converge CFD. To validate the CFD model, a case without water injection was compared to experimental data from Sandia National Laboratory. The predicted in-cylinder pressure and heat release rate showed good agreement with the experimental data. Cases were run with the injection …

Building A Comprehensive Energy Model For Off-Highway Vehicles With Emphasis On Vehicle Thermal Control Systems, Ayhan Zora

Dissertations and Theses @ UNI

Utilizing machine and thermal system simulations (vehicle energy models) can be very helpful for vehicle manufacturing companies to develop a machine with acceptable component temperatures, less heat loads to the vehicle cooling systems, and reduced emissions that will also reduce overall product development cycle.

Energy models of vehicles were developed mostly in the automotive industry, and most of these studies were based on partial energy models.

The aim of this research study was to create a comprehensive energy model for agricultural machinery, which will be a basis for future work on similar products. A tractor model from a Midwest off-road …