Automotive Engineering Commons^™

Design Optimization Of Active-Stabilizing Canards For High-Powered Rockets, Simon Babcock

Senior Honors Theses

Rocket canards are a common means of stabilizing a high-powered rocket in flight by producing aerodynamic forces to correct the rocket's trajectory. The size, shape, and position of the canards relative to the rocket body determine their control effectiveness and aerodynamic efficiency – two objectives of canard design with an inverse relationship to each other. By integrating automated iterative rocket trajectory simulation with adaptive surrogate modelling, this research optimized the canard planform geometry for a high-powered rocket to maximize the canards’ control effectiveness and aerodynamic efficiency through multi-variable, multi-objective design optimization. The canard design was first parameterized into four design …

The Efficacy Of Hybrid Manufacturing For High Stress Automotive Parts, Logan Trimmer

Harrisburg University Other Works

Presentation covering the broad strokes of the project. The goal was to prove the viability of hybrid/additive manufacturing for high stress automotive applications. This project focused on recreating a piston from an old engine to examine if hybrid manufacturing could be used for such applications. On a small scale, hybrid manufacturing was able to be more cost effective if the costs of the equipment and electricity were ignored. The decision to ignore those costs came from the inability to find accurate prices for industrial casting.

Investigation Of The Impact Of The Shape Of The Wings On Formula E Racing Car Performance: Enhancements For Optimal Aerodynamics, Ednie Marthe Adlaikah Jozil

Honors Undergraduate Theses

The aerodynamic performance of a Formula E chassis significantly dictates its overall race efficiency, directly impacting crucial parameters such as battery range and thermal management. This thesis investigates the external aerodynamics of the baseline Gen 2 Formula E car and evaluates the performance gains of two novel aerodynamic packages: a "Fully Modified" configuration and a "Flat Rear Wing" design. Computational Fluid Dynamics (CFD) simulations were conducted to analyze drag coefficients (Cd), downforce generation, and vehicle wake structures at race-relevant free-stream velocities (e.g., 37 m/s and 89 m/s). To ensure numerical robustness, the computational setup was validated using a smooth sphere …

The Efficacy Of Hybrid Manufacturing For High Stress Automotive Components, Logan Trimmer

Harrisburg University Other Works

The goal of this research was to establish the viability of using hybrid manufacturing for automotive applications. By verifying that high-stress components can be created, it can be assumed that any other lower stress part could be made to match the strength requirements. A limiting factor of adoption for hybrid manufacturing is how new the technology is. Studies on time and cost were performed allowing for comparisons with traditional manufacturing technologies (casting, forging, milling) used in automotive applications. This research utilized a Haas Automation UMC750 5-axis CNC mill with a Meltio laser wire direct energy deposition attachment. Fusion 360 was …

Tradespace Exploration For Multiple Collaborative Vehicles, Mrunal Deshmukh

All Theses

Modern military operations demand systems that adapt to uncertain, rapidly changing missions across diverse terrains. Traditional single-platform vehicle design is insufficient for such complexity. This research introduces a hierarchical tradespace exploration framework for designing and evaluating families of heterogeneous ground vehicles under a System-of-Systems (SoS) architecture. The framework treats vehicle design as a co-optimization problem, where a “parent” vehicle (e.g., a Squad Multipurpose Equipment Transport) coordinates specialized “child” vehicles for reconnaissance, amphibious tasks, terrain traversal, and stealth missions. Unlike conventional approaches that optimize vehicles individually, this study emphasizes collaborative performance, resource sharing, and adaptability at the family level. Central to …

Computational Modeling Of Torque Arm And Load Cell Interactions In Uta Racing Brake Dynamometer, Anthony A. Aiyedun

2025 Spring Honors Capstone Projects - Archive

The UTA Racing Team is developing a brake dynamometer to measure the coefficients of friction of various brake pads and calipers under controlled conditions. The dynamometer simulates on-track braking scenarios, testing brake pads at temperatures up to 1300ºF and pressures similar to racing environments. Its primary goal is to generate accurate friction vs. temperature graphs for various brake pad and rotor combinations, addressing the need for dedicated testing equipment. This project creates an ANSYS simulation of the torque arm and load cell interaction. The computational model accurately represents the relationship between applied torque and measured load cell force, incorporating precise …

Advances Towards A Robotic Management Vehicle Suited To Nurse Row Crops To More Efficient Outcomes, Adam Mk Gronewold

Dartmouth College Ph.D Dissertations

Enhancing agricultural production while reducing input costs remains a central challenge in modern row-crop management. Recent advances in computation, imagery, and sensors are enabling more efficient practices across various agricultural domains, and automation technologies are increasingly available to manage tasks central to perennial crop development. Automation in row-crop agriculture, by contrast, lags behind. This thesis explores utilizing small, unmanned ground vehicles to transform row cropping through the implementation of unconventional, in-season management strategies. The first focus of this work considers improvements to nitrogen fertilization using small, autonomous vehicles. An agronomy experiment in corn assessed the effects of gradually applying nitrogen …

Valve Train Design And Material Testing, Luis Luna

Publications and Research

In automotive engineering, CAD software like SolidWorks enables engineers to design and simulate mechanical components efficiently, reducing the need for extensive prototyping. This project examines the rocker arm's performance and durability within a valve train system. Components like pushrods, camshafts, and rocker arms control air intake and exhaust timing. Due to its high-impact motion and exposure to elevated temperatures, the rocker arm endures considerable wear. This study uses SolidWorks and Finite Element Analysis (FEA) to analyze the rocker arm's stress, deformation, and wear potential during camshaft movement. Material testing and motion analysis results provide insights into improving the durability of …

Piston Crown Design, Kurt L. Lippmann, Liam T. Janssen, Alex Rangel, Larry J. Davis

Mechanical Engineering

This project investigates the effects of dimpling a piston crown, and its impact on engine combustion dynamics. Through computational methods, the effects of piston crown dimpling on flow characteristics were evaluated. Theoretical results were verified with experimental methods. Experimental methods included characterization of exhaust gas content, engine horsepower and torque, and exhaust opacity.

Aerodynamic Design And Analysis Of A Modified 2006 Mazda Miata, William N. Recher

Honors College Theses

Aerodynamic forces developed by automobiles have destabilizing effects at high speed. These forces tend to skew toward a vehicle’s rear which can present safety concerns, especially for rear-wheel-drive automobiles like the Mazda Miata. To address oversteer and high-speed instability, a vehicle’s design can be tailored to bring about aerodynamic balance and improve traction. LiDAR was used to bring the physical automobile into the digital space. Then, a splitter and diffuser were added to reduce the magnitude of the destabilizing forces. Next, the size and shape of the rear-wing required to balance the vehicle was calculated using a combination of parameters …

Development Of A Solidworks Api, Andrew Magyar

Williams Honors College, Honors Research Projects

With the current advancements in CAD software, and precision of modern motors, we believe that a new way to communicate from hardware to software is possible. This report details the steps we have taken to attempt just that. The essential idea behind this is that modern controls for robotics are not as user friendly as they can be. The general action taken is to create an API for SolidWorks that connects it to the other necessary controller software and makes it so that a robot, and its exact current position, can be changed simply and intuitively from SolidWorks. Furthermore, the …

Schaeffler E-Axle Value Engineering, Andrew Powers

Williams Honors College, Honors Research Projects

This project aims to design a manufacturable E-Axle end housing that improves system performance while reducing cost. The project is focused on utilizing Schaeffler's manufacturing competencies to achieve a simple assembly with a significant reduction in cost per part, while using existing machines or processes within the company. The design development process will follow the conceptual design stage through Finite Element Analysis and classical engineering calculations. Cross-functional design reviews will be conducted to ensure that agreement can be reached on the manufacturing feasibility of the design. Concepts will be entered in a decision analysis sheet to identify the best one …

Husker Motorsports Active Drag Reduction System, Creighton Hughes, Evan Killian, Micah Busboom, Aj Johnson, Jude Steffen

Honors Program: Senior Projects (Public)

Formula SAE is a multifaceted competition that involves student teams designing and competing with an open-wheel style race car. There are 5 different dynamic events included in the competition. Each event requires a unique aerodynamic setup to have the best performance possible. This design project focuses on a drag reduction system (DRS) that will improve aerodynamic performance, resulting in faster lap times and increased competitiveness. Key features include a direct electronic actuation mechanism that will allow the rear wing to be adjusted during a race. The benefits of the DRS system, include increased speed, improved handling, and greater fuel efficiency …

Design And Manufacture Of An Aerodynamic Body That Meets Scaling Law Requirements And Survives Severe G-Load Environment For Free-Flight Testing, Anthony R. Gonzalez

Graduate Theses, Dissertations, and Problem Reports (ETD)

Design and Manufacture of an Aerodynamic Body that Meets Scaling Law Requirements and Survives Severe G-load Environment for Free-Flight Testing

Anthony Gonzalez

Developing scale models to test functionality and ascertain aerodynamic properties is critical before manufacturing full-size products. Through dimensional analysis and similitude, engineers create scale models to test any parameter of interest. This research aims to design a scale model of an aerodynamic body for repeated free-flight testing. The Froude number is the dominant scale model law used to determine the geometric, mass, and inertia scaling laws. A critical requirement for this research is that the model should be …

Multiple Heat Exchanger Cooling System For Automotive Applications – Design, Mathematical Modeling, And Experimental Observations, Zaker Syed

All Dissertations

The design of the automotive cooling systems has slowly evolved from engine-driven mechanical to computer-controlled electro-mechanical components. With the addition of computer-controlled variable speed actuators, cooling system architectures have been updated to maximize performance and efficiency. By switching from one large radiator to multiple smaller radiators with individual flow control valves, the heat rejection requirements may be precisely adjusted. The combination of computer regulated thermal management system should reduce power consumption while satisfying temperature control objectives. This research focuses on developing and analyzing a multi-radiator system architecture for implementation in ground transportation applications. The premise is to use a single …

Baja Bug Suspension, James Ankers, Rebecca Hansen, Dakota Robert Hollingsworth, Thomas Alfred Spycher

Mechanical Engineering

The goal of this senior project was to design and build a long travel front suspension system for a VW Bug. This started by defining the scope of the project and performing preliminary research. In this step, similar products were investigated, and research was done on stakeholders and customers. Next, concept development, design, and evaluation were performed. With this, the first iteration of our CAD model was designed, and physical prototypes were made. Using all this information, and feedback from advisors and sponsors, multiple iterations of our CAD were performed until the design was ready to manufacture. Drawings were taken …

Human Powered Vehicle Team Challenge, Sydney Nedlik, Spencer Brodie, Maria Griffin, William Schell, Ryan Serraglio

Williams Honors College, Honors Research Projects

Design and build a Human Powered Vehicle in a team of five. Compete at the ASME HPVC competition in March of 2022. Re-establish the Human Powered Vehicle Team at the University of Akron.

Sedan Performance/Economy Rear Diffuser, Jacob Boucher Koris

Thinking Matters Symposium

This project consists of designing in SolidWorks a model of the performance/fuel economy diffuser. The design is modeled with an Ahmed body (recommended shape for CFD testing vehicles) and the diffuser will be applied to the bottom of the rear bumper of the car. After this is done the model will be imported into ANSYS for CFD testing. Testing entails importing the model, then creating a mesh around the model, and then setting up the program to run analysis for calculating the coefficient of drag. Then building this SolidWorks model as a full working prototype for actual road-testing purposes. With …

Design And Analysis Of One-Piece 10” Carbon Fiber Wheels For Zips Racing Zr20 Formula Sae Racecar, Patrick Kruse, Henry J. Wathen, Jordan J. Hyde, Nicholas D. Dobben, Jordan D. Blake

Williams Honors College, Honors Research Projects

Reducing the weight of a vehicle in racing can substantially improve the vehicle dynamics and general performance capabilities. More specifically, the reduction of the unsprung corner weight can provide noticeable performance gains in handling and responsiveness, leading to a quicker, more agile car due to a lower yawing moment of inertia. Unsprung weight reduction also improves the car’s ability to maintain contact between the tires and the road surface for a more consistent grip. In this project we identified the loads that act on the wheel rims according to the data collected from the sensors in the car’s suspension, and …

Dartmouth Formula Racing: Full Electric Battery System Design, Matt Gardner, Jacob Hagler, Ruthie Nordhoff, Otto Salmi

ENGS 89/90 Reports

Dartmouth Formula Racing (DFR) lacked an electrical energy storage system that was Formula Hybrid rules-compliant, optimized for FH events, safe, reliable, and integrated with the rest of their vehicle. Additionally, the team lacked the academic and professional resources required to bring a thorough, analytical approach to the design, testing, and documentation of the new storage system. Our team designed and built a Lithium-Ion battery pack (accumulator) containing energy storage, active cooling, battery management and temperature monitoring systems, and control circuitry compatible with DFR’s vehicle. Collaboration throughout design, fabrication, assembly and testing processes ensured effective knowledge transfer to the DFR team.

A Study Of Model-Based Control Strategy For A Gasoline Turbocharged Direct Injection Spark Ignited Engine, Xin Wang

Dissertations, Master's Theses and Master's Reports

To meet increasingly stringent fuel economy and emissions legislation, more advanced technologies have been added to spark-ignition (SI) engines, thus exponentially increase the complexity and calibration work of traditional map-based engine control. To achieve better engine performance without introducing significant calibration efforts and make the developed control system easily adapt to future engines upgrades and designs, this research proposes a model-based optimal control system for cycle-by-cycle Gasoline Turbocharged Direct Injection (GTDI) SI engine control, which aims to deliver the requested torque output and operate the engine to achieve the best achievable fuel economy and minimum emission under wide range of …

Autonomous Guided Vehicle Frame For Outdoor Use, Thomas Mcgrath

Williams Honors College, Honors Research Projects

The overall goal for my project is to design a durable Autonomous Guided Vehicle (AGV) frame intended for carrying a heavy load over outdoor terrain. I will not be designing a complete vehicle, only the basic structure that can be used to build a complete AGV on. There will be complete 3D models of the design and its individual parts. I also would like to provide limited Finite Element Analysis of the design using ANSYS software to determine weaknesses and methods for improvement. The design I create is meant to be used as a framework for complete outdoor AGV designs. …

Development Of Mbd Model And Analysis Methodology For Vehicle Design, Alfonso Christopher Ponce

Mechanical Engineering ETDs

This thesis is to provide a new methodology that considers the effects the chassis applies during dynamic load to the suspension and the handling characteristics of a road course vehicle. A methodology in which is described in detail as well as an applied demonstration where literature before this thesis, lacks in replication and serves to establish a basis for multi-body dynamic analysis in this area. Two models to be created, rigid and flexible, and to compare each other to study the effects the chassis torsional stiffness has during load transfer. Ultimately, to assist in the design of a vehicle that …

Torsional Stiffness Of A Race Car, Reiley A. Schraeger, Cameron Kao, Raymond Deng, Omar Roman

Mechanical Engineering

Torsional stiffness plays a major role in any road vehicle. To understand torsional stiffness of a vehicle and make future iterations and improvements, a proper torsional stiffness jig is required to prove accurate and useful data. This report encompasses the new and improved testing jig and potential improvement ideas for more accurate results. With real data result relating to FEA calculations, designers can be confident in the FEA changes to torsional stiffness is accurate and will yield the probably results they desired. This report shows the methodology, manufacturing process and testing procedure to use on any Baja or SAE vehicle …

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …

Experimental And Numerical Simulation Of Split Hopkinson Pressure Bar Test On Borosilicate Glass, Mayank K. Bagaria

Dissertations, Master's Theses and Master's Reports

This study is an extension to the design of ceramic materials component exposed to bullet impact. Owing to the brittle nature of ceramics upon bullet impact, shattered pieces behave as pellets flying with different velocities and directions, damaging surrounding components. Testing to study the behavior of ceramics under ballistic impact can be cumbersome and expensive. Modeling the set-up through Finite Element Analysis (FEA) makes it economical and easy to optimize. However, appropriately incorporating the material in modeling makes laboratory testing essential. Previous efforts have concentrated on simulating crack pattern developed during 0.22 caliber pellet impact on Borosilicate glass. A major …

Sae Baja Custom Caliper And Upright Design, Katelynn R. Kise

Williams Honors College, Honors Research Projects

The Zips Baja Off-Road Racing team had a successful 2018 season however some aspects of the car needed to be updated and improved for the 2019 season. This reports captures the design cycle performed to improve the cost, integration, and reliability of the front braking caliper and upright.

Reinventing The Wheel, Esther K. Unti, Ahmed Z. Shorab, Patrick B. Kragen, Adam M. Menashe

Mechanical Engineering

Reinventing the Wheel selected tires and designed wheels for the 2018 Cal Poly, San Luis Obispo Formula SAE combustion vehicle. Available tire options were evaluated for steady-state and transient performance as well as vehicle integration. A single-piece composite wheel with hollow spokes was designed to meet stiffness, strength, and tolerance requirements. A detailed study of wheel loading and geometric structural efficiency was performed. Finite element analysis was used to iterate the geometry and laminate. A two-piece male mold was designed and machined to manufacture the wheel. Removable silicone inserts were used to create the hollow spokes.

Daimscale — 1:14th Tractor-Trailer For Testing Driver Assistance Technology, Christopher Marrale, Jase Sasaki, Devin Bodmer

Mechanical Engineering

Active driver assistance systems are becoming increasingly wide-spread throughout the automotive industry due to their potential for safer roads and decreased costs of transportation, but testing these systems on real trucks can be time consuming, dangerous, and costly. Testing these systems on a small-scale tractor-trailer combination will lead to faster and more efficient development of driver assistance systems and can be used by both engineers and students, leading to a larger field of experienced developers to improve these systems.

Our goal will be to design, manufacture, and build a scale 6x2 model of the tractor portion of a Daimler semi-truck …

Development Of Iowa Dot Combination Bridge Separation Barrier With Bicycle Railing, Chaz M. Ginger

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The Iowa Department of Transportation typically builds separation barriers between vehicle and pedestrian/bicycle facilities when sidewalks or trails are present on vehicular bridges. Currently, Iowa DOT employs a combination bridge rail that utilizes a concrete parapet that previously had been successfully evaluated to National Cooperative Highway Research Program (NCHRP) Report 350 Test Level 4 (TL-4) criteria for these situations. While the parapet had been successfully evaluated, the combination bridge rail system as a whole had not been evaluated to any crash test standards. Iowa DOT desired that researchers at Midwest Roadside Safety Facility (MwRSF) design and test a combination bridge …