Automotive Engineering Commons^™

Inkjet Printing: Facing Challenges And Its New Applications In Coating Industry, Sadegh Poozesh

Theses and Dissertations--Mechanical and Aerospace Engineering

This study is devoted to some of the most important issues for advancing inkjet printing for possible application in the coating industry with a focus on piezoelectric droplet on demand (DOD) inkjet technology. Current problems, as embodied in liquid filament breakup along with satellite droplet formation and reduction in droplet sizes, are discussed and then potential solutions identified. For satellite droplets, it is shown that liquid filament break-up behavior can be predicted by using a combination of two pi-numbers, including the Weber number, We and the Ohnesorge number, Oh, or the Reynolds number, Re, and the Weber number, …

Coded Aperture Aided Navigation And Geolocation Systems, Jamie R. Morrison, John F. Raquet, Michael J. Veth

AFIT Patents

A micro air vehicle having a navigation system with a single camera to determine position and attitude of the vehicle using changes the direction to the observed features. The difference between the expected directions to the observed features versus the measured direction to the observed features is used to correct a navigation solution.

Use Of A Rolling Road System In Crosswind Conditions, Mau-Kuo Chen

Mechanical & Aerospace Engineering Theses & Dissertations

Wind tunnel testing continues to play an important role in vehicle aerodynamic development. Accurate results are strongly associated with whether the wind tunnel can closely simulate the on-road conditions, including the Reynolds number and all boundary conditions. Rolling road systems (or moving belts) have been a successful tool for many auto makers and racing teams to simulate the relative motion between the stationary vehicle model and the floor in the test section. The mechanism of the rolling road system is simple, but how it affects the adjacent flow field and how this flow interacts with the flow underneath the vehicle …

Indeterminate Masses, Elements And Models In Information Fusion, Florentin Smarandache

Branch Mathematics and Statistics Faculty and Staff Publications

In this paper at the beginning, we make a short history of the logics, from the classical Boolean logic to the most general logic of today neutrosophic logic. We define the general logic space and give the definition of the neutrosophic logic. Then we introduce the indeterminate models in information fusion, which are due either to the existence of some indeterminate elements in the fusion space or to some indeterminate masses.

The best approach for dealing with such models is the neutrosophic logic, which is part of neutrosophy. Neutrosophic logic is connected with neutrosophic set and neutrosophic probability and statistics.

Modeling, Identification, Validation And Control Of A Hybrid Maglev Ball System, Ahmed Elhussein E. Mekky

Mechanical & Aerospace Engineering Theses & Dissertations

In this thesis, the electrodynamics of a single axis hybrid electromagnetic suspension Maglev system was modeled and validated by applying it to a single axis hybrid maglev ball experiment. By exploring its linearized model, it was shown that the single axis hybrid Maglev ball has inherently unstable dynamics. Three control scenarios were explored based on the linearized model; (1) Proportional, Deferential (PD) control, (2) Proportional, Deferential, Integral (PID) and (3) PID controller with pre-filtering. This thesis has shown that a PID controller with a pre-filtering technique can stabilize such a system and provide a well-controlled response.

A parametric system identification …

Interface Circuit For A Multiple-Beam Tuning-Fork Gyroscope With High Quality Factors, Ren Wang

Mechanical & Aerospace Engineering Theses & Dissertations

This research work presents the design, theoretical analysis, fabrication, interface electronics, and experimental results of a Silicon-On-Insulator (SOI) based Multiple-Beam Tuning-Fork Gyroscope (MB-TFG). Based on a numerical model of Thermo-Elastic Damping (TED), a Multiple-Beam Tuning-Fork Structure (MB-TFS) is designed with high Quality factors (Qs) in its two operation modes. A comprehensive theoretical analysis of the MB-TFG design is conducted to relate the design parameters to its operation parameters and further performance parameters. In conjunction with a mask that defines the device through trenches to alleviate severe fabrication effect on anchor loss, a simple one-mask fabrication process is employed to implement …

Drag Reduction Of A Modern Straight Truck, Drew Landman, Matthew Cragun, Mike Mccormick, Richard Wood

Mechanical & Aerospace Engineering Faculty Publications

A wind tunnel test program was conducted at the Langley Full Scale Tunnel (LFST) to evaluate the performance of five passive drag reduction configurations on a modern straight truck at full scale. Configurations were tested in a build-up fashion with results representing a cumulative effect. Tested configurations include a front valance, a front box fairing, a boat-tail, an ideal side-skirt, and a practical side-skirt. Configurations were evaluated over a nominal 9 degree yaw sweep to establish wind averaged drag coefficients using SAE J1252. Genuine replicate yaw sweeps were used in an uncertainty analysis. Results show up to 28% improvement in …

Fusion Of Imprecise Qualitative Information, Florentin Smarandache, Xinde Li, Xianzhong Dai, Jean Dezert

Branch Mathematics and Statistics Faculty and Staff Publications

In this paper, we present a new 2-tuple linguistic representation model, i.e. Distribution Function Model (DFM), for combining imprecise qualitative information using fusion rules drawn from Dezert-Smarandache Theory (DSmT) framework. Such new approach allows to preserve the precision and efficiency of the combination of linguistic information in the case of either equidistant or unbalanced label model. Some basic operators on imprecise 2-tuple labels are presented together with their extensions for imprecise 2-tuple labels. We also give simple examples to show how precise and imprecise qualitative information can be combined for reasoning under uncertainty. It is concluded that DSmT can deal …

Stability Analysis, Modeling, Simulation And Experimental Testing Of An Ems Maglev System With Structural Flexibility, Aravind M. Hanasoge

Mechanical & Aerospace Engineering Theses & Dissertations

Vehicle-guideway interaction studies of Magnetically Levitated (Maglev) vehicles indicate that structural flexibility can adversely affect the overall stability and performance of such systems. This is one of the reasons why guideways are generally made very rigid. This in turn leads to increased cost of the overall system since guideway construction forms a significant portion of the overall cost. In this dissertation, the influence of structural flexibility on the stability of Electromagnetic Suspension (EMS) Maglev systems is studied. It is shown how inherently unstable and flexible structure EMS Maglev systems can achieve guaranteed stability by using collocated actuators and sensors, along …

Exploiting A Gsm Network For Precise Payload Delivery, Eugene A. Bourakov, Oleg A. Yakimenko, Nathan Slegers

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

This paper introduces the novel concept of using a GSM network for command of and communications with multiple aerial delivery systems. The research prototype of such a system, Snowflake-N, allows communicating with other network clients via a commercial Blackberry Curve 8310 handheld over a Bluetooth connection. A new architecture allows reassigning targets and sending other relevant commands (via web interface, by voice, data, or text messages) to an onboard autopilot, which is within a network reach, from any place in the world. Similarly, a current position of the descending system and target assignment can be viewed from any computer connected …

Optimal Control For Terminal Guidance Of Autonomous Parafoils, Nathan Slegers, Oleg A. Yakimenko

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

This paper deals with the development of guidance, navigation and control algorithms for a prototype of a miniature aerial delivery system capable of high-precision maneuvering and high touchdown accuracy. High accuracy enables use in precision troop resupply, sensor placement, urban warfare reconnaissance, and other similar operations. Specifically, this paper addresses the terminal phase, where uncertainties in winds cause most of the problems. The paper develops a six degree-of-freedom model to adequately address dynamics and kinematics of the prototype delivery system and then reduces it to a two degrees-of-freedom model to develop a model predictive control algorithm for reference trajectory tracking …

Comment On "Three-Dimensional Ascent Trajectory Optimization For Stratospheric Airship Platforms In The Jet Stream", Nathan Slegers, Ainsmar X. Brown

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

No abstract provided.

Development And Testing Of The Miniature Aerial Delivery System Snowflake, Oleg A. Yakimenko, Nathan Slegers, Robyn A. Tiaden

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

This paper discusses the current status of the development of the miniature aerial delivery system to be further employed in a variety of different research projects. It starts from the overall description of the system and proceeds with the discussion of the test results performed so far. Specifically, it addresses the effects of the changing ground winds on touchdown accuracy. The paper ends with conclusions and recommendations.

Understanding Practical Limits To Heavy Truck Drag Reduction, Drew Landman, Richard Wood, Whitney Seay, John Bledsoe

Mechanical & Aerospace Engineering Faculty Publications

A heavy truck wind tunnel test program is currently underway at the Langley Full Scale Tunnel (LFST). Seven passive drag reducing device configurations have been evaluated on a heavy truck model with the objective of understanding the practical limits to drag reduction achievable on a modern tractor trailer through add-on devices. The configurations tested include side skirts of varying length, a full gap seal, and tapered rear panels. All configurations were evaluated over a nominal 15 degree yaw sweep to establish wind averaged drag coefficients over a broad speed range using SAE J1252. The tests were conducted by first quantifying …

Use Of Variable Incidence Angle For Glide Slope Control Of Autonomous Parafoils, Nathan Slegers, Eric Beyer, Mark Costello

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Strictly speaking, most autonomous parafoil and payload systems possess only lateral control, achieved by right and left parafoil brake deflection. An innovative technique to achieve direct longitudinal control through incidence angle changes is reported. Addition of this extra control channel requires simple rigging changes and an additional servoactuator. The ability of incidence angle to alter the glide slope of a parafoil and payload aircraft is demonstrated through a flight-test program with a microparafoil system. Results from the flight-test program are synthesized and integrated into a six degree-of-freedom simulation. The simulation model is subsequently used to assess the utility of glide …

Rolls Royce Declares Bankruptcy, John Alfred Heitmann

History Faculty Publications

Despite more than sixty years of engineering excellence, Rolls-Royce failed in its attempt to design and manufacture a radically new jet engine to meet contractual obligations with the Lockheed Corp. Consequently, both British and U.S. governments had to step in to avoid an unprecedented economic catastrophe.

Internet Enabled Remote Driving Of A Combat Hybrid Electric Power System For Duty Cycle Measurement, Jarrett Goodell, Marc Compere, Wilford Smith, Mark Brudnak, Mike Pozolo, Et Al.

Publications

This paper describes a human-in-the-loop motion-based simulator interfaced to hybrid-electric power system hardware, both of which were used to measure the duty cycle of a combat vehicle in a virtual simulation environment. The project discussed is a greatly expanded follow-on to the experiment published in [1,7]. This paper is written in the context of [1,7] and therefore highlights the enhancements. The most prominent of these enhancements is the integration (in real-time) of the Power & Energy System Integration Lab (P&E SIL) with a motion base simulator by means of a “long haul” connection over the Internet (a geographical distance of …

Soldier/Hardware-In-The-Loop Simulation-Based Combat Vehicle Duty Cycle Measurement: Duty Cycle Experiment 2, Mark Brudnak, Mike Pozolo, Victor Paul, Syed Mohammad, Marc Compere, Et Al.

Publications

This paper describes a human-in-the-loop motion-based simulator interfaced to hybrid-electric power system hardware both of which were used to measure the duty cycle of a combat vehicle in a virtual simulation environment. The project discussed is a greatly expanded follow-on to the experiment published in [1]. This paper is written in the context of [1] and therefore highlights the enhancements. The most prominent of these enhancements is the integration (in real-time) of the Power & Electric System Integration Lab (P&E SIL) with a motion base simulator by means of a “long haul” connection over the Internet (a geographical distance of …

Variable Structure Observer For Control Bias On Unmanned Air Vehicles, Nathan Slegers, Mark Costello

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

No abstract provided.

Use Of Dynamic Incidence Angle For Glide Slope Control Of Autonomous Parafoils, Nathan Slegers, Eric Beyer, Mark Costello

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Strickly speaking, most autonomous parafoil and payload aircraft possess only lateral control, achieved by right and left parafoil brake deflection. An innovative new technique to achieve direct longitudinal control through dynamic incidence angle changes is reported. Addition of this extra control channel requires simple rigging changes and an additional servo actuator. The ability of dynamic incidence angle to alter the glide slope of a parafoil and payload aircraft is demonstrated through a flight test program with a micro parafoil system. Results from the flight test program are synthesized and integrated into a 6 degree-of-freedom simulation. The simulation model is subsequently …

Robust Control Techniques Enabling Duty Cycle Experiments Utilizing A 6-Dof Crewstation Motion Base, A Full Scale Combat Hybrid Electric Power System, And Long Distance Internet Communications, Marc Compere, Jarrett Goodell, Miguel Simon, Wilford Smith, Mark Brudnak

Publications

The RemoteLink effort supports the U.S. Army's objective for developing and fielding next generation hybrid-electric combat vehicles. It is a distributed soldierin- the-Ioop and hardware-in-the-Ioop environment with a 6-DOF motion base for operator realism, a full-scale combat hybrid electric power system, and an operational context provided by OneSAF. The driver/gunner crewstations rest on one of two 6-DOF motion bases at the U.S. Army TARDEC Simulation Laboratory (TSL). The hybrid power system is located 2,450 miles away at the TARDEC Power and Energy System Integration Laboratory (P&E SIL). The primary technical challenge in the RemoteLink is to operate both laboratories together …

Nonlinear Model Predictive Control Technique For Unmanned Air Vehicles, Nathan Slegers, Jason Kyle, Mark Costello

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

A nonlinear model predictive control strategy is developed and subsequently specialized to autonomous aircraft that can be adequately modeled with a rigid 6-degrees-of-freedom representation. Whereas the general air vehicle dynamic equations are nonlinear and nonaffine in control, a closed-form solution for the optimal control input is enabled by expanding both the output and control in a truncated Taylor series. The closed-form solution for control is relatively simple to calculate and well suited to the real time embedded computing environment. An interesting feature of this control law is that the number of Taylor series expansion terms can be used to indirectly …

Robust Control Techniques For State Tracking In The Presence Of Variable Time Delays, Jarrett Goodell, Marc Compere, Miguel Simon, Wilford Smith, Ronnie Wright, Mark Brudnak

Publications

In this paper, a distributed driver-in-the-Ioop and hardware-in-the-Ioop simulator is described with a driver on a motion simulator at the U.S. Army TARDEC Ground Vehicle Simulation Laboratory (GVSL). Realistic power system response is achieved by linking the driver in the GVSL with a full-sized hybrid electric power system located 2,450 miles away at the TARDEC Power and Energy Systems Integration Laboratory (P&E SIL), which is developed and maintained by Science Applications International Corporation (SAIC). The goal is to close the loop between the GVSL and P&E SIL over the Internet to provide a realistic driving experience in addition to realistic …

Comparison Of Measured And Simulated Motion Of A Controllable Parafoil And Payload System, Nathan Slegers, Mark Costello

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

For parafoil and payload aircraft, control is affected by changing the length of several rigging lines connected to the outboard side and rear of the parafoil leading to complex changes in the shape and orientation of the lifting surface. Flight mechanics of parafoil and payload aircraft most often employ a 6 or 9 DOF representation with the canopy modeled as a rigid body during flight. The effect of control inputs is idealized by the deflection of parafoil brakes on the left and right side of the parafoil. Using a small parafoil and payload aircraft, glide rates and turn performance were …

On The Use Of Rigging Angle And Canopy Tilt For Control Of A Parafoil And Payload System, Nathan Slegers, Mark Costello

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Controllable parafoil and payload aircraft are controlled with downward deflection of left and right parafoil brakes. Lateral control is obtained by differential deflection while longitudinal control is created by collective deflection of the left and right side parafoil brakes. The work reported considers an alternative method to control parafoil and payload air vehicles by tilting the parafoil canopy for lateral control and changing rigging angle for longitudinal control. Using a nonlinear 9 degree of freedom simulation model, it is shown that canopy tilt provides a powerful lateral control mechanism and rigging angle provides a viable longitudinal control mechanism.

External Aerodynamics Of Heavy Ground Vehicles: Computations And Wind Tunnel Testing, Ilhan Bayraktar

Mechanical & Aerospace Engineering Theses & Dissertations

Aerodynamic characteristics of a ground vehicle affect vehicle operation in many ways. Aerodynamic drag, lift and side forces have influence on fuel efficiency, vehicle top speed and acceleration performance. In addition, engine cooling, air conditioning, wind noise, visibility, stability and crosswind sensitivity are some other tasks for vehicle aerodynamics. All of these areas benefit from drag reduction and changing the lift force in favor of the operating conditions. This can be achieved by optimization of external body geometry and flow modification devices. Considering the latter, a thorough understanding of the airflow is a prerequisite.

The present study aims to simulate …

Computational Fluid Dynamic Study Of A Nascar Winston Cup Series Race Car, Terry L. Meek Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

Since the goal of NASCAR racing is to win and since drag is a force the vehicle must overcome, a thorough understanding of the drag generating airflow around and through the automobile is greatly desired. The external airflow contributes to most of the drag that a car experiences and most of the downforce the vehicle produces. Therefore, an estimate of the vehicle's performance may be evaluated using a computational aerodynamics model. This thesis presents a computational fluid dynamic (CFD) analysis of a NASCAR Winston Cup series race car to investigate the salient flow characteristics.

Before a computational analysis could be …

A Feasibility Study Of Fuel Cell Cogeneration In Industry, Scott B. Phelps, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

Up until now, most of the literature on fuel cell cogeneration describes cogeneration at commercial sites. In this study, a PC25C phosphoric acid fuel cell cogeneration system was designed for an industrial facility and an economic analysis was performed. The US DOE Industrial Assessment Center (IAC) database was examined to determine what industry considers a good investment for energy saving measures. Finally, the results of the cogeneration analysis and database investigation were used to project the conditions in which the PC25C might be accepted by industry.

Analysis of IAC database revealed that energy conservation recommendations with simple paybacks as high …

Shape Sensitivity Analysis And Optimization Of Skeletal Structures And Geometrically Nonlinear Solids, Ching-Hung Chuang

Mechanical & Aerospace Engineering Theses & Dissertations

Formulations and computational schemes for shape design sensitivity analysis and optimization have been developed for both skeletal structures and geometrically nonlinear elastic solids. The continuum approach, which is based on the weak variational form of the governing differential equation and the concept of the material derivative, plays a central role in such a development.

In the first part of this work, the eigenvalue and eigenvector sensitivity equations for skeletal structures are derived with respect to configuration variables of joint and support locations. This derivation is done by the domain method as well as the boundary method. The discrete approach for …