Space Vehicles Commons^™

System Integration And Validation Of The Cal Poly Spacecraft Attitude Dynamics Simulator Mk. Iv, Bricen S. Rigby

Master's Theses

The Cal Poly Spacecraft Attitude Dynamics Simulator (SADS) is an ongoing project that seeks to enable the simulation and validation of sensors, actuators, and control logic related to spacecraft attitude control. The SADS platform rests atop a spher- ical air-bearing device which allows for nearly frictionless rotation in all three axes. The orientation of the platform is controlled by four reaction wheels arranged in a pyramidal configuration. Over the past few years, there have been significant updates to the reaction wheel subsystem, as well as requests for a more capable central com- puter. Therefore, a new system architecture for the …

Development Of A Free-Floating Space Robotic Simulator, Truman: Terrestrial Robotic Unit For Multibody Analysis And Navigation, Jackson W. Cordova

Master's Theses

This work describes the development of a 3 Degree-of-Freedom (DOF) robotic manipulator for use on a free-floating planar air-bearing vehicle. The system developed aims to serve as a foundation for future space robotics research at the California Polytechnic State University (Cal Poly)’s Space Robotics Laboratory. Systems doc- umentation describes conceptual operation and architecture of the proposed system: Terrestrial Robotic Unit for Multibody Analysis and Navigation (TRUMAN). The key operation of TRUMAN is to study a self launch maneuver of a free-floating ve- hicle including 4 distinct phases: launch off a fixed rail, coast, reorientation using manipulator motion, and capture of …

Spaceotter: A Floating Spacecraft Simulator Air Bearing Vehicle For Hardware-In-The-Loop Experiments And Research, Alexander Debartolo

Master's Theses

Growing interest in nanosatellites has increased demand for accessible ground-testing methods, which have historically been expensive and restricted. Floating Spacecraft Simulators (FSS), built around Air Bearing Vehicles (ABVs), address this gap by approximating a zero-gravity, friction-minimized environment suitable for testing spacecraft control systems, robotics, and propulsion on the ground.

This thesis presents the design, realization, and initial performance characterization of the Space Optically Tracked Testbed for Experiments and Research (SpaceOTTER) ABV, developed for the Cal Poly Space Robotics Lab. SpaceOTTER is the first step toward emulating the 3 degree of freedom (3-DOF) planar dynamics of a simulated spacecraft and is …

Hamster: Hybrid-Actuated Mobile Spherical Terrain Exploration Rover, Winnie Gao

Master's Theses

The expansion of space exploration to increasingly challenging planetary environments requires mobility systems capable of extreme traversal capabilities and operational reliability. This thesis presents the design, development, and testing of a low-cost Hybrid-Actuated Mobile Spherical Terrain Exploration Rover (HAMSTER) intended for use on a planetary surface exploration mission. HAMSTER uses a pendulum-based actuation method for steering and an actuated internal shaft to propel the vehicle forward. The internal structure includes a two-tiered central case composed of the navigation control module, accelerometer, motor controller, primary DC motor, battery, voltage regulators, Raspberry Pi, pendulum servo motor, and drive shafts. Additive manufacturing through …

A Scalable Iteration Of The Horizon Simulation Framework Using Multithreading Techniques, Jason E. Beals

Master's Theses

The Horizon Simulation Framework (HSF) occupies a unique space in the modern aerospace modeling landscape, enabling flexible, modular modeling of mission-level agent behavior through an object-oriented, hierarchical design. HSF's hallmark breadth-first search scheduling algorithm explores a "multiverse" of possible mission execution pathways, enabling exhaustive evaluation of schedule combinations against user-defined heuristics.

As aerospace systems become increasingly complex, HSF faces critical challenges in establishing verifiable, deterministic behavior. The framework's core scheduling algorithm had not undergone systematic validation, leaving questions about temporal consistency, state management correctness, and reproducibility across different program executions. Furthermore, the exponential growth of schedule combinations creates computational bottlenecks …

Investigation Into Silicone-Silicate Conversion Due To Atomic Oxygen In The Low Earth Orbit Environment, Justin T. Self

Master's Theses

Silicones have been widely used over the years in spacecraft for a variety of functions, but atomic oxygen (AO) exposure in Low Earth Orbit causes a silicate (SiO₂) surface layer to rapidly develop on the silicone which results in a permanent change in its thermal and optical properties. Although this silicone to silicate conversion is known to occur, statistical predictions of layer formation as a function of time on orbit are not found in literature. This thesis utilized optical and scanning electron microscopy, Fourier-Transform Infrared Spectroscopy, diffuse reflectance spectroscopy, and nonlinear regression statistical techniques after RF plasma asher …

Preliminary Analysis Of A 12u Astronomy Cubesat, Charles Van Steenwyk

Master's Theses

The explosion of exoplanet astronomy has led to thousands of new discoveries and opportunities to be explored. The ability to capture images and perform meaningful science has resulted in an abundance of follow-on missions, surveys, and fostered a community of amateur astronomers in the last ten years. This success mirrors the development of CubeSats, which have proved an immensely popular way for students of all levels to access space and collect data. Multiple CubeSats have been developed to observe and characterize single exoplanet tran- sits, showing that this class of mission is possible. However, there is currently no mission designed …

The Effect Of Atomic Oxygen On Additively Manufactured Materials, Ryan Grogan

Master's Theses

Additive manufacturing (AM) is a rapidly developing manufacturing method utilized in fields such as the aerospace industry. In-space AM is a technology of interest for the future of spaceflight, including on-orbit manufacturing. However, AM materials are subject to defects that may impact their performance in space-based applications. How these defects change the material’s reaction to the space environment, specifically atomic oxygen (AO), has only recently been explored. AO is a highly corrosive, dominant constituent in low Earth orbit that causes continuous erosion of spacecraft surfaces. The effect of AO on various AM materials is investigated in this thesis. Stainless steel, …

Launch Vibration Attenuation For In-Space Assembly Cargo, Jered Bell

Master's Theses

This thesis investigates the implementation of a passive isolator with a pressurized air cushion for spacecraft payloads in mission architectures implementing in-space assembly technologies. A pressurized air bed capable of briefly surviving the space environment for cargo delivery was prototyped and experimentally evaluated for launch vehicle vibration dynamics resulting in a 72%, 93%, and 88% reduction in experienced GRMS loads for the X-Axis, Y-Axis, and Z-Axis, respectively. A preliminary Total Mass Loss evaluation of the Low-Density Polyethylene Film utilized for the air bed resulted in a mass loss of 0.7%, indicating that commercial off-the-shelf films might require minimal modification for …

Gyroless Nanosatellite Attitude Determination Using An Array Of Spatially Distributed Accelerometers, Kory J. Haydon

Master's Theses

The low size and budget of typical nanosatellite missions limit the available sensors for attitude estimation. Relatively high noise MEMS gyroscopes often must be employed when accurate knowledge of the spacecraft’s angular velocity is necessary for attitude determination and control. This thesis derived and tested in simulation the “Virtual Gyroscope” algorithm, which replaced a standard gyroscope with an array of spatially distributed accelerometers for a 1U CubeSat mission. A MEMS accelerometer model was developed and validated using Root Allan Variance, and the Virtual Gyroscope was tested both in the open loop configuration and as a replacement for a gyroscope in …

Development Of Mirror Flexures For Use In The Muvi Instrument, Colin W. Harrop

Master's Theses

The Miniaturized Ultraviolet Imager (MUVI), is a compact wide field UV imaging instrument in development at UC Berkeley Space Sciences Laboratory and Cal Poly, San Luis Obispo. MUVI is designed to fit in a 2U CubeSat form factor and provide wide field, high resolution images of the ionosphere at far ultraviolet wavelengths. This thesis details the design and analyses of MUVI’s deployable cover mirror mounting flexures. Three different flexure geometries were evaluated, an optimal candidate was determined based on a number of criteria including isolation of vibration and stress to the mirrors, manufacturability and cost. The design of the flexure …

Investigation On The Use Of Small Aperture Telescopes For Leo Satellite Orbit Determination, Luis R. Curiel Iii

Master's Theses

The following thesis regards the use of small aperture telescopes for space domain awareness efforts. The rapidly populating space domain was motivation for the development of a new operation scheme to conduct space domain awareness feasibility studies using small telescopes. Two 14-inch Schmidt-Cassegrain Telescopes at the California Polytechnic State University and the Air Force Research Lab in Kirtland AFB, NM, in conjunction with a dedicated CCD camera and a commercial DSLR camera, were utilized to conduct optical observations on satellites in Earth orbit.

Satellites were imaged during August 2019, and from January 2020 to March 2020, resulting in the collection …

B-Plane Targeting With The Spacecraft Trajectory Optimization Suite, Jared Graef

Master's Theses

In interplanetary trajectory applications, it is common to design arrival trajectories based on B-plane target values. This targeting scheme, B-plane targeting, allows for specific target orbits to be obtained during mission design. A primary objective of this work was to implement B-plane targeting into the Spacecraft Trajectory Optimization Suite (STOpS). This work was based on the previous versions of STOpS done by Fitzgerald and Sheehan, however STOpS was redeveloped from MATLAB to python. This updated version of STOpS implements 3-dimensional computation, departure and arrival orbital phase modeling with patched conics, B-plane targeting, and a trajectory correction maneuver. The optimization process …

Design, Validation, And Verification Of The Cal Poly Educational Cubesat Kit Structure, Nicholas B. Snyder

Master's Theses

In this thesis, the development of a structure for use in an educational CubeSat kit is explored. The potential uses of this kit include augmenting existing curricula with aspects of hands on learning, developing new ways of training students on proper space systems engineering practices, and overall contributing to academic capacity building at Cal Poly and its collaborators. The design improves on existing CubeSat kit structures by increasing accessibility to internal components by implementing a modular backplane system, as well as adding the ability to be environmentally tested. Manufacturing of the structure is completed with both additive (Fused Deposition Modeling …

Performance Enhancement And Characterization Of An Electromagnetic Railgun, Paul M. Gilles

Master's Theses

Collision with orbital debris poses a serious threat to spacecraft and astronauts. Hypervelocity impacts resulting from collisions mean that objects with a mass less than 1g can cause mission-ending damage to spacecraft. A means of shielding spacecraft against collisions is necessary. A means of testing candidate shielding methods for their efficacy in mitigating hypervelocity impacts is therefore also necessary. Cal Poly’s Electromagnetic Railgun was designed with the goal of creating a laboratory system capable of simulating hypervelocity (≥ 3 km/s) impacts. Due to several factors, the system was not previously capable of high-velocity (≥ 1 km/s) tests. A deficient projectile …

The Effects Of Atomic Oxygen On Patch Antenna Performance And Lifetime, Max J. Barta

Master's Theses

The space environment is a volatile and challenging place for satellites to survive in. For Low Earth Orbiting (LEO) satellites, atomic oxygen (AO) is a constant corrosive effect that degrades the outer surface of satellites over long durations. Atomic oxygen exists in the atmosphere between 180 and 675 km and has a relatively high energy at 4.5 eV, which allows AO to break molecular bonds in materials on the surfaces of spacecraft. As the number and complexity of CubeSat missions increase, there is an increased risk that AO degradation on commercial off the shelf parts (COTS), such as antenna, could …

Nanosatellite Launch Data-Logger (Sync), Christopher Martin Gerdom

Master's Theses

CubeSat designers are increasingly looking to incorporate delicate structures and optics into their payloads. These delicate payloads, however, may not survive the required absolute-worst-case launch vibration testing needed for flight certification. To help address this problem, and to better match testing conditions to real-world launch environments, this thesis introduces Sync, a compact 1/4U CubeSat payload designed to collect data on the vibrations and thermal environments CubeSats experience inside a deployer on the way to orbit. This data can be used to better understand the launch environment for different vehicles, and help develop new, more realistic testing guidelines that could enable …

Use Of Manifolds In The Insertion Of Ballistic Cycler Trajectories, Oliver K. Morrison

Master's Theses

Today, Mars is one of the most interesting and important destinations for humankind and copious methods have been proposed to accomplish these future missions. One of the more fascinating methods is the Earth-Mars cycler trajectory which is a trajectory that accomplishes repeat access to Earth and Mars with little to no fuel-burning maneuvers. This would allow fast travel to and from Mars, as well as grant the possibility of multiple missions using the same main vehicle.

Insertion from Earth-orbit onto the cycler trajectory has not been thoroughly ex- plored and the only existing method so far is a Hohmann-esque transfer …

Modification Of A Ground Based Atomic Oxygen Simulation Apparatus To Accommodate Three Dimensional Specimens, Charles Ward

Master's Theses

The space environment presents various challenges when designing systems and selecting materials for applications beyond Earth’s atmosphere. For mission success, these challenges must be considered. One of the detrimental aspects of the space en- vironment is Atomic Oxygen, AO. Only present in harmful quantities in Lower Earth Orbit, LEO, AO causes significant damage to materials by breaking molecular bonds. California Polytechnic State University’s, Cal Poly’s, space environments laboratory features an apparatus capable of simulating this environment. Very thin or short samples were tested to observe the mass loss due to erosion of the sample material. Recent modifications to the system …

Utilizing Permanent On-Board Water Storage For Efficient Deep Space Radiation Shielding, Nathan Ryan Gehrke

Master's Theses

As space technologies continue to develop rapidly, there is a common desire to launch astronauts beyond the ISS to return to the Moon and put human footsteps on Mars. One of the largest hurdles that still needs to be addressed is the protection of astronauts from the radiation environment seen in deep space. The most effective way to defend against radiation is increasing the thickness of the shield, however this is limited by strict mass requirements. In order to increase the thickness of the shield, it is beneficial to make mission critical items double as shielding material.

The human rated …

Exploring The Concept Of A Deep Space Solar-Powered Small Spacecraft, Kian Guillaume Crowley

Master's Theses

New Horizons, Voyager 1 & 2, and Pioneer 10 & 11 are the only spacecraft to ever venture past Pluto and provide information about space at those large distances. These spacecraft were very expensive and primarily designed to study planets during gravitational assist maneuvers. They were not designed to explore space past Pluto and their study of this environment is at best a secondary mission. These spacecraft rely on radioisotope thermoelectric generators (RTGs) to provide power, an expensive yet necessary approach to generating sufficient power. With Cubesats graduating to interplanetary capabilities, such as the Mars-bound MarCO spacecraft, matching the modest …

Alternative Mission Concepts For The Exploration Of Outer Planets Using Small Satellite Swarms, Andrew Gene Blocher

Master's Theses

Interplanetary space exploration has thus far consisted of single, expensive spacecraft missions. Mission costs are particularly high on missions to the outer planets and while invaluable, finite budgets limit our ability to perform extensive and frequent investigations of the planets. Planetary systems such as Jupiter and Saturn provide extremely complex exploration environments with numerous targets of interest. Exploring these targets in addition to the main planet requires multiple fly-bys and long mission timelines. In LEO, CubeSats have changed the exploration paradigm, offering a fast and low cost alternative to traditional space vehicles. This new mission development philosophy has the potential …

Sysml Based Cubesat Model Design And Integration With The Horizon Simulation Framework, Shaun Luther

Master's Theses

This thesis examines the feasibility of substituting the system input script of Cal Poly’s Horizon Simulation Framework (HSF) with a Model Based Systems Engineering (MBSE) model designed with the Systems Modeling Language (SysML). A concurrent student project, SysML Output Interface Creation for the Horizon Simulation Framework, focused on design of the HSF Translator Plugin which converts SysML models to an HSF specific XML format. A SysML model of the HSF test case, Aeolus, was designed. The original Aeolus HSF input script and the translated SysML input script retained the format and dependency structure required by HSF. Both input scripts …

An Iteration On The Horizon Simulation Framework To Include .Net And Python Scripting, Morgan Yost

Master's Theses

Modeling and Simulation is a crucial element of the aerospace engineering design pro- cess because it allows designers to thoroughly test their solution before investing in the resources to create it. The Horizon Simulation Framework (HSF) v3.0 is an aerospace modeling and simulation tool that allows the user to verify system level requirements in the early phases of the design process. A low fidelity model of the system that is created by the user is exhaustively tested within the built-in Day-in-the-Life simulator to provide useful information in the form of failed requirements, system bottle necks and leverage points, and potential …

Structural Micrometeoroid And Radiation Shielding For Interplanetary Spacecraft, Jared Allen Ruekberg

Master's Theses

This paper focused on two significant space forces that can affect the success of a spacecraft: the radiation and micrometeoroid environments. Both are looked at in the context of the region of space between Earth and Mars. The goal was create reference environments, to provide context to results of environmental modeling, and to provide recommendations to assist in early design decisions of interplanetary spacecraft. The radiation section of this report used NASA's OLTARIS program to generate data for analysis. The area of focus was on the radiation effects for crewed missions, therefore effective dose equivalent was the metric used to …

Improving And Expanding The Capabilities Of The Poly-Picosatellite Orbital Deployer, David Pignatelli

Master's Theses

The Poly-Picosatellite Orbital Deployer (P-POD) has undergone a series of revisions over the years. The latest revision, described in this Master’s Thesis, incorporates new capabilities like EMI shielding, an inert gas purge system, and an electrical interface to the CubeSats after they are integrated into the P-POD. Additionally, some mass reduction modifications are made to the P-POD, while its overall strength is increased. The P-POD inert gas purge system successfully flew, on a previous revision P-POD. The P-POD components are analyzed to a set of dynamic loads for qualification, and successfully undergoes random vibration qualification testing. The P-POD encounters some …

Development Of Safety Standards For Cubesat Propulsion Systems, Liam Jon Cheney

Master's Theses

The CubeSat community has begun to develop and implement propulsion systems. This movement represents a new capability which may satisfy mission needs such as orbital and constellation maintenance, formation flight, de-orbit, and even interplanetary travel. With the freedom and capability granted by propulsion systems, CubeSat providers must accept new responsibilities in proportion to the potential hazards that propulsion systems may present.

The Cal Poly CubeSat program publishes and maintains the CubeSat Design Specification (CDS). They wish to help the CubeSat community to safety and responsibly expand its capabilities to include propulsive designs. For this reason, the author embarked on the …

Analysis Of An Inflatable Gossamer Device To Efficiently De-Orbit Cubesats, Robert A. Hawkins Jr.

Master's Theses

There is an increased need for spacecraft to quickly and efficiently de-orbit themselves as the amount of debris in orbit around Earth grows. Defunct spacecraft pose a significant threat to the LEO environment due to their risk of fragmentation. If these spacecraft are de-orbited at the end of their useful life their risk to future spacecraft is greatly lessened. A proposed method of efficiently de-orbiting spacecraft is to use an inflatable thin-film envelope to increase the body's area to mass ratio and thusly shortening its orbital lifetime. The system and analysis presented in this project is sized for use on …

A Generic Decision Making Framework For Autonomous Systems, Connor Lange

Master's Theses

With the rising popularity of small satellites, such as CubeSats, many smaller institutions previously incapable of developing and deploying a spacecraft have starting to do so. Institutions with a history of space flight, such as NASA JPL, have begun to put projects on CubeSats that would normally fly on much larger satellites. As a result, the institutions with space flight heritage have begun to port spacecraft software that was previously designed for much larger and more complex satellites to the CubeSat platform. Unfortunately for universities, who are the majority of all institutions devel- oping CubeSats, these ported systems are too …

Feasibility Of Microsatellite Active Debris Removal Systems, Karsten J. James

Master's Theses

Space debris has become an increasingly hazardous obstacle to continued spaceflight operations. In an effort to mitigate this problem an investigation of the feasibility of a microsatellite active debris removal system was conducted. Through proposing a novel concept of operation, utilizing a grapple-and-tug system architecture, and by analyzing each resultant mission phase in the frame of a representative example, it was found that microsatellite scale systems are capable of fulfilling the active debris removal mission. Analysis of rendezvous, docking, control and deorbit mission requirements determined that the design of a grapple-and-tug system will be driven by sizing of the propellant …