Space Vehicles Commons^™

Terramechanics-Based Comparison Of Dem And Crm For Lunar Surface Applications, Nicolas Bonasoro

Discovery Day - Daytona Beach

Understanding how lunar regolith interacts with robotic systems is important for safe surface operations because uncertain terrain conditions can affect rover traversability and lunar lander stability. This work applies terramechanics to two space robotics applications: in-situ cone penetration testing (CPT) for terrain assessment and lunar lander touchdown analysis for evaluating sinkage, force response, and stability. The study compares the Discrete Element Method (DEM), which resolves particle-scale interactions and captures detailed regolith behavior, with the Continuum Representation Method (CRM), which models soil response more efficiently and supports rigid CAD components such as lander footpads, legs, and body geometries. Current CPT results …

Mars Rover Wheels And Drive, Presley S. Sacavitch, Ryan W. Trevena, Dylan A. Mack, Daniel Hudak

Mechanical Engineering

Cal Poly’s Poly1Rover team, advised by Professor Rich Murray, aims to deploy four student-designed mini-Mars rovers, each equipped with a sample-tube retrieval claw, before 2030. However, the wheels of Poly1Rover’s current 6th generation rover are not ready for deployment to Mars, as they do not utilize space-grade materials, are not optimized for manufacturability, and lack sufficient spoke compliance to absorb landing and high-impact loads. This project will be developed by a team of Mechanical Engineering students at California Polytechnic State University, San Luis Obispo (Cal Poly): Daniel Hudak, Dylan Mack, Presley Sacavitch, and Ryan Trevena. Next Intent is providing funding …

Design And Development Of A Passive Dust Protection System For Lunar Docking Operations, Simon Thengvall

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Lunar docking systems face a unique set of environmental conditions that can create significant challenges for mechanical design. Among these, the abrasive nature of lunar regolith can impair the kinematic function of traditional terrestrial mechanisms as well as contaminate critical spacecraft components such as environmental seals, causing them to fail. For crew-rated docking systems, failure of these systems not only threatens mission success, but also crew safety, so dust protection is crucial for docking components. To address the concerns of regolith intrusion, the Simple External Attachment for Lunar Openings (SEALO) is developed as a key architecture for mechanism evaluation when …

Effect Of Nozzle Pressure Ratio On Thrust And Flow Behavior In A Supersonic De Laval Nozzle, Esha Jain

Doctoral Dissertations and Master's Theses

Supersonic nozzles operate across a range of flow regimes. While an ideally expanded condition yields optimal thrust, practical propulsion systems rarely operate at this design point due to variations in altitude and engine operating conditions. As a result, nozzles frequently operate in off-design conditions. In overexpanded regime, where the exit pressure is lower than the ambient pressure, shock-induced separation may occur within the divergent section of the nozzle, potentially degrading nozzle performance. Understanding the aerodynamic behavior of nozzles operating under off-design conditions is therefore important for improving propulsion system performance and stability. In particular, direct thrust measurements provide a key …

Set-Theoretic Reachability-Informed Model Predictive Control For Mechanical And Aerospace Systems, Jinaykumar Nitinkumar Patel

Mechanical and Aerospace Engineering Dissertations

Modern mechanical and aerospace systems increasingly operate autonomously in environments characterized by nonlinear dynamics, uncertainty, and safety constraints. In these settings, estimation and control methods based on nominal models and single-point trajectory predictions are usually insufficient to ensure safe and reliable operation. This dissertation uses a set-theoretic perspective, in which the system state, uncertainty, and admissible behavior are described by sets instead of point estimates. The key question is not only what the state is, but what set of states remains consistent with the dynamics, disturbances, control limits, and available measurements. This provides bounded descriptions of uncertainty and supports control …

A Computational Approach To Graduated Centrifuge Profiles For Partial Gravity Planetary Environments, Cabell W. Jones

Mechanical & Aerospace Engineering Faculty Publications

Missions such as NASA’s Artemis and SpaceX’s Starship aspire towards creating permanent settlements beyond Earth. In order to achieve this goal, it must be considered that the gravity present on planetary surfaces such as the Moon (0.165 g) and Mars (0.378 g) may be insufficient to support human physiology for long term habitation. On near-Earth missions, issues such as muscular atrophy, neuro-ocular changes, cardiopulmonary variations, and bone mineral density loss have been observed proportional to the duration spent in microgravity. Further studies have suggested that the severity of these conditions scales linearly with decreasing gravity, meaning that astronaut health can …

Multiphysics Transport In Porous Thermal Protection Systems: Experimental Characterization Of Gas Permeability And Radiative Properties, Yejajul Hakim

Theses and Dissertations--Mechanical and Aerospace Engineering

Porous thermal protection systems (TPS) used in hypersonic vehicles exhibit coupled gas and radiative transport across multiple regimes and length scales. Accurate performance prediction requires reliable characterization of permeability, slip-flow behavior, and radiative transport properties, particularly for low-permeability and charred materials where existing data are limited. This dissertation presents experimental methods for characterizing multiphysics transport in porous TPS materials. A modular flow system was developed to measure permeability and slip behavior in both virgin and charred materials under relevant environments. A transient pressure decay method enables accurate permeability estimation in low-permeability regimes and provides insight into effective pore structure. Results …

Thermal Radiation Effects On Particles From Plasma Arc Radiation, Reece Davis, Joseph Mcgee

Williams Honors College, Honors Research Projects

Understanding the radiation heating and transport of both microparticles and nanoparticles is a phenomenon that is critical for both space and Earth sciences. In space, these particles are heated by plasma arcs within ionized space clouds or solar flares and can be present the path of deep space missions and orbital satellites. While on Earth, processes such as forest fires, nuclear fusion, and microchip manufacturing include the plasma arc heating of particles. These particles lay within the Mie Scattering Regime and Rayleigh Scattering Regime and emit radiation differently based on their diameter. New mathematical and computational modeling has been conducted …

Automated Soil Resetting System For Extraterrestrial Regolith Simulation, Parker W. Brennan, Anthony C. Daniels

Williams Honors College, Honors Research Projects

This project focuses on designing an automated soil resetting system for extraterrestrial regolith simulation. The system will prepare a regolith simulant testbed to a desired, repeatable density, enabling reliable wheel–terrain testing for planetary rover research. Manual soil preparation currently exposes testers to hazardous particulates and produces inconsistent results.

The proposed system will integrate mechanical and control elements to reset the soil bed safely and efficiently. A combination of raking and vibrational methods will be explored, with feedback sensors and automation to achieve target density control. The research will proceed through literature review, benchtop experimentation, prototype design, and full-scale testing over …

Modeling And Testing Chain Trencher Excavator And Cone Penetrometer Robotic Prospecting Systems For Lunar In-Situ Resource Utilization, Marcello C. Guadagno

Dissertations, Master's Theses and Master's Reports

The Artemis Missions aim to establish a sustained human presence on the Moon, requiring In-Situ Resource Utilization (ISRU) of water-ice deposits in permanently shadowed regions. Two critical capabilities must be developed to enable ISRU at scale: prospecting instruments that can characterize the spatial distribution and geotechnical properties of icy regolith in situ, and excavation systems that can extract hardened icy regolith efficiently. This dissertation addresses both needs through the development and testing of a Percussive Heated Cone Penetrometer (PHCP) for geotechnical prospecting and a chain trencher excavator for icy regolith mining.

The PHCP was developed across eight design iterations and …

Extraction Of Aluminum From Lunar Regolith Through Molten Salt Electrolysis, Jacob N. Ortega, Todd P. Sander, Jeffrey D. Smith, Fateme Rezaei, David J. Bayless, William Schonberg, Daniel S. Stutts, Frank D. Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents the methodology, development, and results of an end-to-end regolith-to-metal concept for producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method. Using electrolytic reduction, aluminum oxide (i.e., alumina) can be reduced into aluminum and oxygen via electrolysis in a molten salt bath. A steady supply of hydrogen chloride could allow this in-situ resource utilization (ISRU) method to supply several necessary materials consumed in the electrolytic reduction step of the process to produce bulk aluminum metal, oxygen, water, and silica from anorthite abundant in lunar highland regions. In this …

Ground Testing Of A Magnetic-Electrostatic Separation System For Lunar Regolith Beneficiation, Peter Bachle, Charles Wood, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

The separation of lunar regolith by mineral composition and size category is useful forin-situ resource utilization (ISRU). The research presented herein discusses the designing and development of equipment that has the potential to separate lunar regolith into aluminum, iron-titanium, and magnesium-iron ores. Along with the metal ore separation, this equipment shows the potential to separate regolith by size categories. The combined effect of these separation methods generates output that is valuable to subsequent use in metal and oxygen extraction, additive manufacturing, and regolith sintering processes. The designed equipment uses a dual-strength magnet system with N42 and N52 neodymium magnets for …

Kinetic Modeling Of Dust Grain Dynamics In Electrostatic Sieving, Aaron Berkhoff, Easton Ingram, Fateme Rezaei, Jeffrey Smith, David Bayless, William Schonberg, Daoru Han

Chemical and Biochemical Engineering Faculty Research & Creative Works

A new kinetic particle modeling framework was developed to investigate electrostatic transport of lunar regolith dust particles with applications to the concept of electrostatic sieving. the new approach is based on kinetic particle dynamics and includes major modules of sampling the particle size distribution, solving electric fields, and tracking motion of charged dust grains. a case study for a concept of electrostatic sieving was chosen to validate the new model. the simulation achieved similar performance of particle size classification as reported in the literature. the new model is computationally efficient (takes a few minutes on a PC-type laptop computer) so …

Ultrashort Pulsed Laser Treatment Is Effective At Sterilizing Metal Surfaces For Planetary Protection, Kaleb Mcquillan

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

To prevent forward contamination from microbes aboard spacecraft intended for exploration of solar system bodies there is a need for effective sterilization methods. However, current techniques are both time-consuming and expensive. For example, dry heat sterilization requires removal from the assembly site and several days of treatment. Furthermore, some components such as optics and electronics are not compatible with current sterilization techniques. In this thesis, a novel femtosecond laser surface processing technique for the rapid sterilization of spacecraft hardware is reported. Femtosecond lasers produce extremely high photon fluxes (10²⁹ photons/s*cm², ~0.03 J/cm²) in extremely short …

Rasc-Al Large Scale Lunar Crater Prospector, Austin Arnold, Coleman Alvarez, Mark Suberu

Senior Design Project For Engineers

The purpose of this project is to design a conceptual layout of a lunar rover capable of exploring craters at the lunar south pole. The rover should be autonomous and capable of self-sustainment for at least one year in extreme cold and darkness. While determining the location and accessibility of water ice and other volatiles within the crater. This document will contain all information related to the team's conceptual design. Including research, component selection, electrical design, and mechanical design.

Lunar Rascals Video: https://www.youtube.com/watch?v=MdcjzVMtzaI

Experimental And Numerical Analysis Of Laminar And Transitional Flow Through Annular Corrugated Pipes, Joseph Russell Sargent

Theses and Dissertations

This dissertation presents studies on pressure loss through annular corrugated pipes to determine a friction factor coefficient using nitrogen. Ten different corrugated pipes’ geometries were evaluated via testing and experimentation. The ratio of corrugation height to inner diameter varied from 0.233 to 0.333 and the ratio of corrugation pitch to inner diameter varied from 0.181 to 0.446. Nitrogen flow rates between 0.25 to 94.4 standard liters per minute were used, resulting in Reynolds numbers, based on the corrugated pipe inner diameter, from 100 to 23,000. The experimental set-up was validated using smooth-pipe pressure loss measurements and the derived friction factor …

Magnetic Separation Of Lunar Regolith Simulants With Applications To In Situ Resource Utilization On The Moon, Peter Bachle, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Chemical and Biochemical Engineering Faculty Research & Creative Works

The development of in situ resource utilization (ISRU) for metal extraction is imperative as a steppingstone for habitation construction in lunar and non-terrestrial environments. Separation of minerals by chemical composition is important to optimize metal and oxygen liberation from lunar ore. To this effect, devices capable of separating aluminum bearing minerals from iron-bearing minerals from the lunar regolith simulants have been developed. Twenty-eight different simulants have been used in this study. A dual-belt separator was designed to reduce middling. Para-magnetic minerals were reliably separated using a neodymium N52-magnet-separator system. Effective separation of aluminum-bearing minerals from iron-bearing minerals was greater than …

Modelling Of The Viscoelastic Relaxation Of A Stowed Telescope Starshade, Rahul Raghu

Graduate Thesis and Dissertation 2023-2024

The Habitable Worlds Telescope Starshade is an occulting disk that orbits in tandem with a telescope that occludes and diffuses the light from stars to observe the relatively dim exoplanets in orbit around them. It achieves this in part with tailored petals that diffuse light to soften the light from the star. Due to the relative sizes of the star and the planet, NASA considers the shape stability of the Starshade's petals to be a Key Technology Gap. The Starshade is developed to be a deployable composite structure that folds on itself to fit within modern rockets. Due to the …

Electrostatic Sorting Of Lunar Regolith Simulants For Sustainable Resource Utilization: Modeling And Characterization Of Particle Size Distribution, Abdullah Al Moinee, Peter Bachle, Kyle Newport, William Schonberg, David Bayless, Jeffrey Smith, Daoru Han, Fateme Rezaei

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pursuit of sustainable resource utilization on the Moon, this paper delves into modeling and characterization of particle size distribution (PSD) of lunar regolith simulants in an electrostatic system. A prototype electrostatic sieve was built and tested with four sample simulants mirroring properties of lunar mare and highland regolith. An alternating four-phase (90 degrees, 180 degrees, 270 degrees, 360 degrees) traveling square-wave was utilized for particle-directed transport to model the diverse trajectories of the particles. Numerically, we scrutinized how the distribution functions of the particles are manifested as the electrostatic field propagates, with a focus on three distinct particle ranges …

Electrostatic Sorting Of Lunar Regolith Simulants For Sustainable Resource Utilization: Modeling And Characterization Of Particle Size Distribution, Abdullah Al Moinee, Peter Bachle, Kyle Newport, William Schonberg, David Bayless, Jeffrey Smith, Daoru Han, Fateme Rezaei

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pursuit of sustainable resource utilization on the Moon, this paper delves into modeling and characterization of particle size distribution (PSD) of lunar regolith simulants in an electrostatic system. a prototype electrostatic sieve was built and tested with four sample simulants mirroring properties of lunar mare and highland regolith. an alternating four-phase (90 degrees, 180 degrees, 270 degrees, 360 degrees) traveling square-wave was utilized for particle-directed transport to model the diverse trajectories of the particles. Numerically, we scrutinized how the distribution functions of the particles are manifested as the electrostatic field propagates, with a focus on three distinct particle ranges …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Propulsion Heat Analysis Nuclear Trajectory Optimization (Phantom), Ana Clecia Alves Almeida, Jonathan Davis, Ryan Dippolito

Williams Honors College, Honors Research Projects

Interplanetary Travel requirements necessitate the use of increasingly complex propulsion systems. Nuclear Thermal Propulsion (NTP) is a cutting-edge concept that holds immense potential for the future of space exploration. By utilizing nuclear fission to heat a propellant and generate thrust, NTP offers the potential for unprecedented efficiency, enabling faster interplanetary travel and extended mission capabilities. A nuclear thermal rocket engine is a type of propulsion system that utilizes the heat generated by a nuclear reactor to heat and expel a propellant, typically hydrogen, at high velocities to produce thrust. The engine consists of three main subsystems: the nuclear reactor, the …

Magnetic Separation Of Lunar Regolith Simulants With Applications To In Situ Resource Utilization On The Moon, Peter Bachle, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

The development of in situ resource utilization (ISRU) for metal extraction is imperative as a steppingstone for habitation construction in lunar and non-terrestrial environments. Separation of minerals by chemical composition is important to optimize metal and oxygen liberation from lunar ore. to this effect, devices capable of separating aluminum bearing minerals from iron-bearing minerals from the lunar regolith simulants have been developed. Twenty-eight different simulants have been used in this study. a dual-belt separator was designed to reduce middlings. Para-magnetic minerals were reliably separated using a neodymium N52-magnet-separator system. Effective separation of aluminum-bearing minerals from iron-bearing minerals was greater than …

Kinetic Modeling Of Electrostatic Sieving For Lunar Regolith Beneficiation: Case Studies, Easton Ingram, Emmanuela Amen Eze, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

A new kinetic particle modeling framework was developed to investigate electrostatic transport of lunar regolith particles with applications to the concept of electrostatic sieving. the new approach is based on kinetic particle dynamics and includes major modules of sampling the particle size distribution, solving electric fields, and tracking motion of charged dust grains. Case studies for a concept of electrostatic sieving were chosen to validate the new model. the simulation achieved similar yields reported in previous works, which served as validation of the model. the new model is computationally efficient and could serve as a design, analysis, and optimization tool.

Progress Of Lisap-Mse: A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, David Bayless, Daniel Stutts, Daoru Han, Todd P. Sander, Jeffrey Smith, Fateme Rezaei, William Schonberg

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Steady And Transient Study Of Conjugate Heat Transfer In Regenerative Cooled Nozzle, Khaled Bensayah, Khadidja Kamri

Emirates Journal for Engineering Research

The Heat transfer is one of the most serious challenges that exist in a supersonic nozzle flow. The combustion chamber wall and the nozzle are exposed to high-temperature gases during combustion and gas expansion, which can eventually lead to structural failure. This paper reports a computational study of steady and transient conjugate heat transfer in regenerative water cooled nozzle. Numerical computation solved Reynolds-averaged equations based on RSM-Omega turbulence model coupling with solid-phase heat conduction equation and with coolant-phase. The effect of four inlet cooled approach length 0 inch, 6 inch, 12 inch and 18 inch are studied and validated against …

Hardware-In-The-Loop Reaction Wheel Testbed With Camera Vision, Abigail Romero, Harvey Perkins, Stephen Kwok-Choon

College of Engineering Summer Undergraduate Research Program

Reaction wheels are widely used in aerospace systems as a method of attitude control. This research was focused on the design, development, and testing of a hardware-in-the-loop reaction wheel testbed that can be used for research and teaching applications related to satellite navigation and control. This project successfully utilized commercial off-the-shelf components to develop a reaction wheel capable of controlling the orientation of a freely rotating platform, as well as tracking objects using computer vision.

The Influence Of Mixing Duct Length And Phase Of Flight On Wall Temperatures Of A Rocket Based Combined Cycle Engine In Ejector And Air-Augmented Modes, Jonathan Grow

Doctoral Dissertations and Master's Theses

Rocket Based Combined Cycle (RBCC) engines have been theorized as a possible means of powering launch vehicles and high-speed atmospheric vehicles. By incorporating aspects of both air-breathing and rocket propulsion, RBCC engines promise up to a 230 % increase in specific impulse over traditional chemical rocket propulsion by entraining a secondary flow of atmospheric air and mixing it with the exhaust of a rocket motor. Students within the Embry-Riddle Future Space Explorers and Developers Society (ERFSEDS) identified a
problem of excessive heating and structural failure of the mixing duct during launch and transonic flight of a student-built flight test vehicle. …

A Systematic Study Into The Design And Utilization Of Burn Wire As A Means Of Tensioning And Releasing Spacecraft Mechanisms Through Applied Joule Heating, Chandler Dye

Mechanical Engineering Undergraduate Honors Theses

The joule heating characteristics of Nichrome burn wires, often used as a thermal cutting device in mechanisms designed to fasten and release CubeSat deployables, are examined in the following thesis. Wires ranging from 0.125 inches to 2 inches long, and diameters of 30 Ga and 40 Ga, are investigated through analytical calculations and thermal simulations based on heat transfer due to joule heating, and through physical circuitry-based experiments. The temperature data is used to generate heating curves to predict the time it takes for Nichrome wires to fail under varying testing parameters. This research aims to catalog a series of …

Development Of Mirror Flexures For Use In The Muvi Instrument, Colin W. Harrop

Master's Theses

The Miniaturized Ultraviolet Imager (MUVI), is a compact wide field UV imaging instrument in development at UC Berkeley Space Sciences Laboratory and Cal Poly, San Luis Obispo. MUVI is designed to fit in a 2U CubeSat form factor and provide wide field, high resolution images of the ionosphere at far ultraviolet wavelengths. This thesis details the design and analyses of MUVI’s deployable cover mirror mounting flexures. Three different flexure geometries were evaluated, an optimal candidate was determined based on a number of criteria including isolation of vibration and stress to the mirrors, manufacturability and cost. The design of the flexure …