Other Aerospace Engineering Commons^™

Aerodynamic And Acoustic Modeling For Evtol Rotor Noise Prediction, Daniella Bezuidenhout, Anastasios S. Lyrintzis, Vladimir V. Golubev

Doctoral Dissertations and Master's Theses

This thesis presents the development and validation of a methodology for predicting total acoustic emissions from a one-fifth scale electric vertical takeoff and landing (eVTOL) rotor in both hover and edgewise flight conditions. The approach couples sectional two-dimensional Reynolds-Averaged Navier-Stokes (2D-RANS) airfoil simulations with rotor loading predictions from the Comprehensive Hierarchical Aeromechanics Rotorcraft Model (CHARM), tonal noise calculations using the acoustic solver PSU-WOPWOP, and broadband noise predictions from the UCD-QuietFly framework. Boundary-layer inputs traditionally obtained from the viscous-inviscid solver, XFOIL, were replaced with higher-fidelity 2D-RANS results from OpenFOAM to better capture low-Reynolds-number flow physics, including laminar-turbulent transition and laminar separation …

Performance Of Adaptive Wingtips On A Tailless Supersonic Business Jet, Khushi Piparava

2025 Fall Honors Capstones Projects - Archive

The growing interest in supersonic business travel has renewed focus on efficient, low-drag configurations that can achieve high performance while maintaining stability and structural integrity. This research investigates the aerodynamic and structural implications of adaptive folding wingtips on a tailless supersonic business jet (SBJ) concept designed under the SkyBreaker senior design program. Using a conceptual aerodynamic model based on linearized supersonic theory, the Polhamus leading-edge suction analogy, and an empirical compression-lift correlation, the study evaluates how varying wingtip droop angles influence lift, drag, lift-to-drag ratio (L/D), and static stability. The analysis was performed parametrically in MATLAB, using geometry inputs derived …

High-Fidelity Modeling Of Evtol Rotor Unsteady Aerodynamic And Aeroacoustic Response To Time-Harmonic Gust, Vadim Voropayev

Doctoral Dissertations and Master's Theses

The rapid emergence of Urban Air Mobility (UAM) demands accurate prediction and mitigation of noise generated by electric vertical take-off and landing (eVTOL) aircraft operating in complex urban environments. Among the various noise sources, the aerodynamic and acoustic response of rotors to unsteady inflow represents a major uncertainty in community-noise assessment and certification. This thesis investigates the aerodynamic and aeroacoustic behavior of a representative eVTOL rotor subjected to time-harmonic inflow disturbances, providing a detailed numerical framework to quantify how periodic gusts influence rotor performance, unsteady loading, and sound radiation.

The study employs a three-stage computational methodology using the open-source solver …

Modeling Of Rotor Wake Vortex Dynamics And Interactions In Non-Homogenous Vertiport Environments, Garrison P. Shaw

Doctoral Dissertations and Master's Theses

The current research serves to analyze and study the effects ground forces can have on the thrust performance of a propeller in multiple different configurations. The current research utilizes an open source Computational Fluid Dynamics (CFD) software known as OpenFOAM to generate calculate and visualize these runs. The model used for this experiment is a hybrid model that employs both a Unsteady Reynolds-Averaged Navier-Stokes (URANS) and a detached eddy simulation using a hybrid Large Eddy Simulation (LES) via a KomegaSSTDDES model. This model serves to save computational time as well as allow for accurate results. The three cases run are …

Development Of Load Measurement Technique For Arbitrary Shapes, Quintin J. Cockrell

Master's Theses

Obtaining aerodynamic forces and moments about all three orthogonal axes for arbitrary shapes at arbitrary orientations in a fast manner via a measurement technique specific to Cal Poly’s low-speed wind tunnel to continually obtain the forces and moments under quasi-steady conditions is explored. A Continuous Rotation Technique (CR) uses a 6-DOF load cell and stepper motor to rotate an object about an axis for a complete rotation. The forces and moments acting upon the object pass through the stepper motor and interface plates and recorded by the load cell as the object is rotated continuously a finite number of rotations. …

Foundations For Finite-State Modelling Of A Two-Dimensional Airfoil That Reverses Direction, Jake Michael Oscar Welsh

McKelvey School of Engineering Graduate Student Theses & Dissertations

Current 3-D finite-state wake models are incapable of simulating a maneuver in which the sign of the free-stream velocity changes direction and the rotor enters its own wake -- as might occur in the case of a helicopter which ascends and then descends. It is the purpose of this work to create a 2-D finite-state wake model which is capable of handling changes in free-stream direction as a precursor to development of a 3-D model that can do the same.

The 2-D finite-state model used for reentry modifications is an existing model created by Peters, Johnson, and Karunamoorthy. By the …

Design And Flight-Path Simulation Of A Dynamic-Soaring Uav, Gladston Joseph

Doctoral Dissertations and Master's Theses

We address the development of a dynamic-soaring capable unmanned aerial vehicle (UAV) optimized for long-duration flight with no on-board power consumption. The UAV’s aerodynamic properties are captured with the integration of variable fidelity aerodynamic analyses. In addition to this, a 6 degree-of-freedom flight simulation environment is designed to include the effects of atmospheric wind conditions. A simple flight control system aids in the development of the dynamic soaring maneuver. A modular design paradigm is adopted for the aircraft dynamics model, which makes it conducive to use the same environment to simulate other aircraft models. Multiple wind-shear models are synthesized to …

Next-Generation Re-Entry Aerothermodynamic Modeling Of Space Debris Using Machine Learning, Nicholas Sia

Graduate Theses, Dissertations, and Problem Reports (ETD)

The number of resident space objects re-entering the atmosphere is expected to rise with increased space activity over recent years and future projections. Predicting the survival and impact location of the medium to large sized re-entering objects becomes important as they can cause on ground casualties and damage to property. Uncertainties associated with the re-entry process makes necessary a probabilistic approach, which can be computationally expensive when using high-fidelity numerical methods for estimating aerothermodynamic properties. To date, object-oriented analysis is the dominant tool used for atmospheric re-entry modeling and simulation, where aerothermodynamic coefficients are used to determine the risk a …

Comparison Of Flow Field In The Proximity Of A Single Planar & Wrap-Around Fin, Nayhel Sharma, Palak Saini, Hrishabh Chaudhary, Gurteg Nagi, Rakesh Kumar Dr.

International Journal of Aviation, Aeronautics, and Aerospace

Abstract

This paper analyses the results of the computational analysis between a single planar and a wrap-around fin mounted on a semi-cylindrical body. A free-stream Computational Fluid Dynamics (CFD) model was simulated for both cases in the Mach 0.4-3.0M range at 0°Angle of attack, in which, the behavior of flow around the fin was investigated using a turbulence model of higher order discretization. The post-processing shows all the possible views of the flow dynamics around the fins, as well as the missile body. The aerodynamic drag and the rolling moment characteristics of the planar and the wrap-around fin have been …

Wing Deflection Analysis Of 3d Printed Wind Tunnel Models, Matthew G. Paul

Master's Theses

This work investigates the feasibility of producing small scale, low aerodynamic loading wind tunnel models, using FDM 3D printing methods, that are both structurally and aerodynamically representative in the wind tunnel. To verify the applicability of this approach, a 2.07% scale model of the NASA CRM was produced, whose wings were manufacturing using a Finite Deposition Modeling 3D printer. Experimental data was compared to numerical simulations to determine percent difference in wake distribution and wingtip deflection for multiple configurations.

Numerical simulation data taken in the form of CFD and FEA was used to validate data taken in the wind tunnel …

Book Review: High G Flight - Physiological Effects And Countermeasures, Stefan Kleinke

International Journal of Aviation, Aeronautics, and Aerospace

This review provides insight on the content and a review of the quality of the recent release of High G Flight - Physiological Effects and Countermeasures from Ashgate Publications.

This review does not reflect the views of IJAAA or ERAU. This work was not peer reviewed.

High G Flight - Physiological Effects and Countermeasures

Designing The Human-Powered Helicopter: A New Perspective, Gregory Hamilton Gradwell

Master's Theses

The concept of human-powered vertical flight was studied in great depth. Through the manipulation of preexisting theory and analytical methods, a collection of design tools was created to expediently conceptualize and then analyze virtually any rotor. The tools were then arranged as part of a complete helicopter rotor design process. The lessons learned as a result of studying this process—and the tools of which it consists—are presented in the following discussion. It is the belief of the author that by utilizing these tools, as well as the suggestions that accompany them, future engineers may someday build a human-powered helicopter capable …

Cfd As Applied To The Design Of Short Takeoff And Landing Vehicles Using Circulation Control, Tyler M. Ball

Master's Theses

The ability to predict the distance required for an aircraft to takeoff is an essential component of aircraft design. It involves aspects related to each of the major aircraft systems: aerodynamics, propulsion, configuration, structures, and stability and control. For an aircraft designed for short takeoffs and landings (STOL), designing the aircraft to provide a short takeoff distance, or more precisely the balanced field length (BFL), often leads to the use of a powered lift technique such as circulation control (CC). Although CC has been around for many years, it has never been used on a production aircraft. This is in …