Other Aerospace Engineering Commons^™

The Effect Of Biocomposite Material In A Composite Structure Under Compression Loading, Benjamin Andrew Sweeney

Master's Theses

While composite structures exhibit exceptional strength and weight saving possibilities for engineering applications, sometimes their overall cost and/or material performance can limit their usage when compared to conventional structural materials. Meanwhile ‘biocomposites’, composite structures consisting of natural fibers (i.e. bamboo fibers), display higher cost efficiency and unique structural benefits such as ‘sustainability’. This analysis will determine if the integration of these two different types of composites are beneficial to the overall structure. Specifically, the structure will consist of a one internal bamboo veneer biocomposite ply; and two external carbon fiber weave composite plies surrounding the bamboo biocomposite. To acquire results …

Assessment Of Asymmetric Flight On Solar Uas, Eric Belfield

Master's Theses

An investigation was conducted into the feasibility of using an unconventional flight technique, asymmetric flight, to improve overall efficiency of solar aircraft. In this study, asymmetric flight is defined as steady level flight in a non-wings-level state in- tended to improve solar incidence angle. By manipulating aircraft orientation through roll angle, solar energy collection is improved but aerodynamic efficiency is worsened due to the introduction of additional trim drag. A point performance model was devel- oped to investigate the trade-off between improvement in solar energy collection and additional drag associated with asymmetric flight. A mission model with a focus on …

Development Of Cal Poly's Shock Table, Christopher D. Risner

Master's Theses

Shock is one of the environmental tests that a spacecraft must pass before being cleared for launch. Shock testing poses a challenging data acquisition issue and careful selection of equipment is crucial to creating a successful shock test facility. Cal Poly’s CubeSat programs can currently perform all environmental testing other than shock themselves, so a quality shock table would be useful. Previous groups of students had developed a shock table, and this paper details the improvement and characterization of that shock table’s behavior. Several adjustable parameters were tested and documented to discover trends in the shock table’s response to an …

Evaluation Of Efficiency Of Various Materials To Shield From Radiation In Space Using The Monte Carlo Transport Code Called Fluka, Roman Savinov

Master's Theses

The purpose of this study is to improve spacecraft shielding from radiation in space. It focuses on the evaluation of shielding efficiency of different materials. The efficiency of a shield is evaluated by the dose profile within the shield and the amount of dose absorbed by a target using the Monte Carlo transport code called FLUKA. The output of this code is validated by recreating the experiments from published papers and comparing the results. Once the FLUKA’s output is validated, the efficiency of sixteen materials, subject to SPE and GCR sources, are evaluated. The efficiency comparison is made by fixing …

Axisymmetric Bi-Propellant Air Augmented Rocket Testing With Annular Cavity Mixing Enhancement, Allen A. C. Capatina

Master's Theses

Performance characterization was undertaken for an air augmented rocket mixing duct with annular cavity configurations intended to produce thrust augmentation. Three mixing duct geometries and a fully annular cavity at the exit of the nozzle were tested to enable thrust comparisons. The rocket engine used liquid ethanol and gaseous oxygen, and was instrumented with sensors to output total thrust, mixing duct thrust, combustion chamber pressure, and propellant differential pressures across Venturi flow measurement tubes.

The rocket engine was tested to thrust maximum, with three different mixing ducts, three major combustion pressure sets, and a nozzle exit plane annular cavity (a …

Development Of Tools Needed For Radiation Analysis Of A Cubesat Deployer Using Oltaris, Marycarmen Gonzalez-Dorbecker

Master's Theses

Currently, the CubeSat spacecraft is predominantly used for missions at Low- Earth Orbit (LEO). There are various limitations to expanding past that range, one of the major ones being the lack of sufficient radiation shielding on the Poly-Picosatellite Orbital Deployer (P-POD). The P-POD attaches to a launch vehicle transporting a primary spacecraft and takes the CubeSats out into their orbit. As the demand for interplanetary exploration grows, there is an equal increase in interest in sending CubeSats further out past their current regime. In a collaboration with NASA’s Jet Propulsion Laboratory (JPL), students from the Cal Poly CubeSat program worked …

Development Of An Interactive Wave Drag Capability For The Openvsp Parametric Geometry Tool, Michael Jon Waddington

Master's Theses

Minimizing wave drag is critical to successful and efficient transonic and supersonic flight. Area-ruling is the process of managing the cross-sectional area of an aircraft to lessen the wave drag experienced in flight. Effectively calculating the necessary areas for a given aircraft can be difficult, and existing tools for conducting a wave drag analysis often carry limitations in both functionality and availability.

In this work, the author utilized an existing parametric geometry tool named OpenVSP to create an interactive design tool for approximating zero-lift wave drag. Here, the wave drag calculation methodology used in industry for decades is combined with …

A Study On The Vibrational Performance Characteristics Of An E22 Isolator After Outgassing And Bake-Out, Alma Melendez

Master's Theses

The launch environment experiences many vibration, shock, and acoustic loads. A great concern is the high random vibration levels that can damage components and spacecraft structures, which can cause a mission failure. An effective method of reducing high frequency energy is using isolators. Overall, the need for vibration isolation has been increasing because there has been an increase in the use of mechanisms in which vibrations are prevalent. In addition, there has not been extensive research on the effects of isolators that are outgassed and cured. Therefore, it is important to investigate and understand the vibrational effects on isolators. It …

Thermal Analysis Of A Monopropellant Micropropulsion System For A Cubesat, Erin C. Stearns

Master's Theses

Propulsive capabilities on a CubeSat are the next step in advancement in the Aerospace Industry. This is no longer a quest that is being sought by just university programs, but a challenge that is being taken on by all of the industry due to the low-cost missions that can be accomplished. At this time, all of the proposed micro-thruster systems still require some form of development or testing before being flight-ready. Stellar Exploration, Inc. is developing a monopropellant micropropulsion system designed specifically for CubeSat application.

The addition of a thruster to a CubeSat would expand the possibilities of what CubeSat …

A Study Of The Collisional Evolution Of Orbital Debris In Geopotential Wells And Geo Disposal Orbits, Christina R. Diaz

Master's Theses

This thesis will present the effects of the orbital debris evolution in two key areas: the geosynchronous disposal orbit regime known as “graveyard” and the two geopotential wells found in 105◦ W and 75◦ E longitude bins. After developing a GEO specific orbit propagator for NASA Johnson Space Center’s Orbital Debris Of- fice, collisions were simulated throughout these regimes using a low velocity breakup model. This model considered the effects of perturbations particularly non-spherical Earth effects (specifically sectorial and zonal harmonics), lunar effects, third body effects and solar radiation pressure effects. The results show that CDPROP does well in simulating …

The Feasibility And Application Of Observing Small Leo Satellites With Amateur Telescopes, Brock Schmalzel

Master's Theses

This thesis demonstrates that any individual can provide relevant observational data to further research efforts within the Aerospace community, through the use of amateur telescopes. A Meade LX200 12 in. telescope and Lumenera Skynyx 2.0 camera were utilized to observe small LEO satellites, using a well-documented point-and-wait staring method. Over a period of three months, a total of 186 observation attempts were made resulting in 97 successful captures. From the gathered data, three possible aerospace applications were analyzed: validation of a satellite brightness prediction model, angles-only orbit determination including extended Kalman filtering, and temporal error growth in TLE-based orbit propagation. …

Design, Fabrication, And Testing Of An Emr Based Orbital Debris Impact Testing Platform, Jeffrey J. Maniglia Jr.

Master's Theses

This paper describes the changes made from Cal Poly’s initial railgun system, the Mk. 1 railgun, to the Mk. 1.1 system, as well as the design, fabrication, and testing of a newer and larger Mk. 2 railgun system. The Mk. 1.1 system is developed as a more efficient alteration of the original Mk. 1 system, but is found to be defective due to hardware deficiencies and failure, as well as unforeseen efficiency losses. A Mk. 2 system is developed and built around donated hardware from the Naval Postgraduate School. The Mk. 2 system strove to implement an efficient, augmented, electromagnetic …

Micrometeoroid Fluence Variation In Critical Orbits Due To Asteroid Disruption, Eliot Dan Aretskin-Hariton

Master's Theses

Micrometeoroids and orbital debris (MMOD) is a growing issue with international importance. Micrometeoroids are naturally occurring fragments of rock and dusk that exist throughout the solar system. Orbital debris is human made material like rocket bodies, paint flakes, and the effluent of spacecraft collisions. Even small MMOD particles on the order of 1 cm in diameter have the potential to destroy critical spacecraft systems. Because of this, MMOD is a threat to all spacecraft in orbit. Even governments that most sternly oppose US international policy have a stake when it comes to minimizing MMOD flux. Space-based assets are essential to …

Improvement Of Electromagnetic Railgun Barrel Performance And Lifetime By Method Of Interfaces And Augmented Projectiles, Aleksey D. Pavlov

Master's Theses

Several methods of increasing railgun barrel performance and lifetime are investigated. These include two different barrel-projectile interface coatings: a solid graphite coating and a liquid eutectic indium-gallium alloy coating. These coatings are characterized and their usability in a railgun application is evaluated. A new type of projectile, in which the electrical conductivity varies as a function of position in order to condition current flow, is proposed and simulated with FEA software. The graphite coating was found to measurably reduce the forces of friction inside the bore but was so thin that it did not improve contact. The added contact resistance …

Ad-Hoc Regional Coverage Constellations Of Cubesats Using Secondary Launches, Guy G. Zohar

Master's Theses

As development of CubeSat based architectures increase, methods of deploying constellations of CubeSats are required to increase functionality of future systems. Given their low cost and quickly increasing launch opportunities, large numbers of CubeSats can easily be developed and deployed in orbit. However, as secondary payloads, CubeSats are severely limited in their options for deployment into appropriate constellation geometries.

This thesis examines the current methods for deploying cubes and proposes new and efficient geometries using secondary launch opportunities. Due to the current deployment hardware architecture, only the use of different launch opportunities, deployment direction, and deployment timing for individual cubes …

Control System Development For Small Uav Gimbal, Nicholas J. Brake

Master's Theses

The design process of unmanned ISR systems has typically driven in the direction of increasing system mass to increase stabilization performance and imagery quality. However, through the use of new sensor and processor technology high performance stabilization feedback is being made available for control on new small and low mass stabilized platforms that can be placed on small UAVs. This project develops and implements a LOS stabilization controller design, typically seen on larger gimbals, onto a new small stabilized gimbal, the Tigereye, and demonstrates the application on several small UAV aircraft. The Tigereye gimbal is a new 2lb, 2-axis, gimbal …

Cubesat Constellation Analysis For Data Relaying, Bradley Ryan Smalarz

Master's Theses

Current CubeSat communication technology limits the amount of time, and number of accesses with ground stations. It has been proposed to use a constellation of CubeSats to improve relay performance and increase the number of accesses between a CubeSat and ground stations. By using the spatial and temporal analysis features of STK, coupled with the STK/Matlab interface a robust tool was created to analyze the performance of CubeSat constellations based on a store-and-forward communications model which is not currently supported by the STK Engine. Utilizing the Connect messaging format through a socket connection on the local machine, a Matlab graphical …

Designing The Human-Powered Helicopter: A New Perspective, Gregory Hamilton Gradwell

Master's Theses

The concept of human-powered vertical flight was studied in great depth. Through the manipulation of preexisting theory and analytical methods, a collection of design tools was created to expediently conceptualize and then analyze virtually any rotor. The tools were then arranged as part of a complete helicopter rotor design process. The lessons learned as a result of studying this process—and the tools of which it consists—are presented in the following discussion. It is the belief of the author that by utilizing these tools, as well as the suggestions that accompany them, future engineers may someday build a human-powered helicopter capable …

Autonomous Satellite Operations For Cubesat Satellites, Jason Lionel Anderson

Master's Theses

In the world of educational satellites, student teams manually conduct operations daily, sending commands and collecting downlinked data. Educational satellites typically travel in a Low Earth Orbit allowing line of sight communication for approximately thirty minutes each day. This is manageable for student teams as the required manpower is minimal. The international Global Educational Network for Satellite Operations (GENSO), however, promises satellite contact upwards of sixteen hours per day by connecting earth stations all over the world through the Internet. This dramatic increase in satellite communication time is unreasonable for student teams to conduct manual operations and alternatives must be …

Multidisciplinary Design Optimization Of An Extreme Aspect Ratio Hale Uav, Bryan J. Morrisey

Master's Theses

ABSTRACT

Multidisciplinary Design Optimization of an Extreme Aspect Ratio HALE UAV

Bryan J. Morrisey

Development of High Altitude Long Endurance (HALE) aircraft systems is part of a vision for a low cost communications/surveillance capability. Applications of a multi payload aircraft operating for extended periods at stratospheric altitudes span military and civil genres and support battlefield operations, communications, atmospheric or agricultural monitoring, surveillance, and other disciplines that may currently require satellite-based infrastructure. Presently, several development efforts are underway in this field, including a project sponsored by DARPA that aims at producing an aircraft that can sustain flight for multiple years and …

An Experiment On Integrated Thermal Management Using Metallic Foam, Derek M. Geiger

Master's Theses

This report details an approach to using metal foam heat exchangers inside an integrated thermal management system on a variable cycle engine. The propulsion system of interest is a variable cycle engine with an auxiliary, variable flow rate fan. The feasibility of utilizing an open-celled metallic foam heat exchanger in the ducting between the constant and variable-fans on this variable cycle engine to cool the avionics was explored using an experimental approach. Two heat exchangers, 6.3 inch width by 6.3 inch length by 0.5 inch thickness, were constructed from 20 and 40 pores per inch (PPI) metal foam and tested. …

A Flight Simulation Study Of The Simultaneous Non-Interfering Aircraft Approach, Brian H. Reel

Master's Theses

Using a new implementation of a NASA flight simulation of the Quiet Short-Haul Research Aircraft, autopilots were designed to be capable of flying both straight in (ILS) approaches, and circling (SNI) approaches. A standard glideslope coupler was sufficient for most conditions, but a standard Proportional-Integral-Derivative (PID) based localizer tracker was not sufficient for maintaining a lateral track on the SNI course. To track the SNI course, a feed-forward system, using GPS steering provided much better results.

NASA and the FAA embrace the concept of a Simultaneous, Non-Interfering (SNI) approach as a way to increase airport throughput while reducing the noise …

Cfd As Applied To The Design Of Short Takeoff And Landing Vehicles Using Circulation Control, Tyler M. Ball

Master's Theses

The ability to predict the distance required for an aircraft to takeoff is an essential component of aircraft design. It involves aspects related to each of the major aircraft systems: aerodynamics, propulsion, configuration, structures, and stability and control. For an aircraft designed for short takeoffs and landings (STOL), designing the aircraft to provide a short takeoff distance, or more precisely the balanced field length (BFL), often leads to the use of a powered lift technique such as circulation control (CC). Although CC has been around for many years, it has never been used on a production aircraft. This is in …