Other Aerospace Engineering Commons^™

Modeling And Testing Chain Trencher Excavator And Cone Penetrometer Robotic Prospecting Systems For Lunar In-Situ Resource Utilization, Marcello C. Guadagno

Dissertations, Master's Theses and Master's Reports

The Artemis Missions aim to establish a sustained human presence on the Moon, requiring In-Situ Resource Utilization (ISRU) of water-ice deposits in permanently shadowed regions. Two critical capabilities must be developed to enable ISRU at scale: prospecting instruments that can characterize the spatial distribution and geotechnical properties of icy regolith in situ, and excavation systems that can extract hardened icy regolith efficiently. This dissertation addresses both needs through the development and testing of a Percussive Heated Cone Penetrometer (PHCP) for geotechnical prospecting and a chain trencher excavator for icy regolith mining.

The PHCP was developed across eight design iterations and …

Investigation Of The Impact Of The Shape Of The Wings On Formula E Racing Car Performance: Enhancements For Optimal Aerodynamics, Ednie Marthe Adlaikah Jozil

Honors Undergraduate Theses

The aerodynamic performance of a Formula E chassis significantly dictates its overall race efficiency, directly impacting crucial parameters such as battery range and thermal management. This thesis investigates the external aerodynamics of the baseline Gen 2 Formula E car and evaluates the performance gains of two novel aerodynamic packages: a "Fully Modified" configuration and a "Flat Rear Wing" design. Computational Fluid Dynamics (CFD) simulations were conducted to analyze drag coefficients (Cd), downforce generation, and vehicle wake structures at race-relevant free-stream velocities (e.g., 37 m/s and 89 m/s). To ensure numerical robustness, the computational setup was validated using a smooth sphere …

Active Measurement Of A Micron-Order Gap Under High-Speed And High-Temperature Conditions, Andrew Becker

Doctoral Dissertations and Master's Theses

The hypersonic regime poses numerous challenges that researchers face in the development of hypersonic flight vehicles. Due to their excellent thermomechanical properties, ultra-high-temperature ceramics (UHTCs) have risen as a promising solution to act as a protective barrier between the harsh environment and surface materials of these flight bodies. The mechanical operation of a portable hypersonic simulation device was developed in-house and tested at Argonne National Laboratories (ANL) to gather in-situ material response of prospective UHTC samples when exposed to a hypersonic regime. An edge detection-based algorithm was developed and used in LabVIEW to monitor the health and operation of the …

Advancing Real-World Implementation Of The Well Optimized Linear Finder (Wolf) High-Speed Atmospheric Turbulence Compensation Method, Timothy Evan Coon

Theses and Dissertations

This dissertation advances the real-world implementation of the Well Optimized Linear Finder (WOLF) method for high-speed Atmospheric Turbulence Compensation (ATC). Atmospheric turbulence introduces phase aberrations into optical wavefronts and degrades image quality in terrestrial imaging systems. Traditional phase diversity methods are computationally intensive and poorly suited to real-time operation. The WOLF method addresses these limitations through a novel, point-wise formulation of the optical transfer function (OTF) as a structured autocorrelation of the generalized pupil function (GPF). This formulation enables the estimation of phase aberrations at individual spatial coordinates with distributed computational complexity.

The research begins by developing a MATLAB-based simulation …

An Engineering Solution For Fan Aeroacoustics Measurements Correction In A Non-Anechoic Testing Environment, Saad-Eldin Taha, Mohamed Y.Zakaria, Mohamed Abdelgaied, M.M. Bassuoni Prof. Dr.

Journal of Engineering Research

Abstract- Nowadays, acoustic signatures of daily used applications are to be minimized. The study of noise generated through aerodynamic interaction with moving bodies has passed through different phases since the early 50s, and this leads to the evolvement of many analytical, empirical and computational techniques in order to be able to estimate the emitted noise. Concerning fan blades, until now the researches are still going for a reliable method for noise estimation during the early phases of design which help in the development of blades with a lower aeroacoustic signature, the Brooks, Pope and Marcolini (BPM) model was chosen to …

Pressure Switch Tester, Michael Starasinich, Andrew Dobson, Jordan Huschen, Mitchell Smith, Melvin Brown Iii

Honors Capstones

Abstract—- The Pressure Switch Test Stand is a comprehensive and automated testing solution designed to streamline the actuation and validation of simultaneously. At the core of the system is a PLC-controlled architecture that enables precise control and simulation of pressure conditions, replicating real-world scenarios to ensure accurate and reliable switch performance.

This test stand integrates robust mechanical fixtures, a reliable pneumatic control system, custom-designed electrical circuits, and a modular software interface, working in unison to deliver consistent and high-fidelity testing outcomes. Each pressure switch undergoes a sequence of pressure ramps and holds, with the system continuously monitoring switch states, activation …

Ultrafast Laser Surface Structuring For Wettability Control On Copper, Akshay Arvind Nagvenkar

All Theses

Wettability is a crucial surface property influencing various phenomena, including heat transfer, cell adhesion, and corrosion. Engineering devices can achieve superior performance by precisely manipulating surface wettability. As a result, extensive research has focused on developing surfaces that exhibit either extreme water attraction (superhydrophilic) or strong water repellency (superhydrophobic). Tailoring surface wettability paves the way for numerous applications, such as drag reduction in marine vessels, controlled drug delivery, efficient water collection, advanced liquid transport systems, oil-water separation, anti-corrosion coatings, friction reduction, and self-cleaning materials. Ultrafast laser surface structuring is a promising approach for engineering multifunctional surfaces, effectively modifying material properties …

Reconfigurable Python Autopilot Software For Rc Aircraft, Kate Doiron

Honors Theses

No abstract provided.

G.W.A.I.H.I.R. Guided Wing Aircraft For Intelligent Hybrid Insertion And Recovery, Abdirahman Ahmed Shirwa, Zach Richards, Derek Harwood, Alex Duncan

Senior Design Project For Engineers

The paper outlines the conceptual and preliminary design of a hybrid vertical takeoff and landing (VTOL) heavy lift unmanned aerial vehicle (UAV) for autonomous cargo transport missions. The primary design objective was to create an aircraft capable of carrying a 15 kg payload over a range of 33 km, achieving a top cruise speed of 45 km/h and maintaining an endurance capacity of at least 90 minutes.

A comprehensive literature review informed key design decision, including airfoil selection, structural material, propulsion system configuration, and control. Key requirements were established early in the design process, such as payload capacity, energy efficiency, …

Damping Modulation Of Dampened Kapton Surfaces, Sebastian Esteban

Honors Undergraduate Theses

When droplets are vibrated or disturbed, they can exhibit a complex sloshing motion, an understudied behavior in drop physics. Droplet sloshing involves a complex combination of transverse and longitudinal motion that changes the droplet's effective weight on the surface the droplet is on. Our current understanding stems from preliminary work focusing on a cantilever beam of fixed thickness and variable viscosity of the liquid being sloshed. This investigation will focus on how variable cantilever thickness and constant viscosity for a liquid being sloshed affects the beam's deflection under consistent vibration. It will also investigate how the natural frequency of a …

Cryogenic Fuel Applications To Sustainable Commercial Aircraft, Jack R. Kisling, Lillian Panning

College of Engineering Summer Undergraduate Research Program

Finding a source of clean and renewable energy is one of the greatest challenges humanity will face in the 21st century. With populations expanding, developing countries increasing their use of resources, and the rapid and alarming effects of climate change, a shift to a sustainable future is an existential prospect.

The goal of our project is to take the first steps toward getting safety procedures and lab space established, so mechanical engineering senior projects can quickly begin to experiment with cryogenic fuels. They will explore the application of cryogenic fuels to commercial aviation.

The Pressure Distribution Of Rotating Cylinders Using An Onboard Wireless Data Acquisition System, Nathan Eller

Master's Theses

This thesis presents a novel, cost-effective method for mapping the pressure distribution on a rotating cylinder in cross flow, a phenomenon central to the Magnus effect. Utilizing commercial-off-the-shelf (COTS) micro-electromechanical system (MEMS) pressure sensors, a high-resolution data acquisition system was developed and integrated into a rotating cylinder model. Compared to traditional approaches, such as slip rings or one-off designs, this method proved significantly cheaper and faster while achieving comparable or superior resolution. The experimental setup, including a modified continuous rotation technique and adaptable model design, facilitated rapid testing across a broad range of Reynolds numbers and reduced frequencies, exceeding the …

Experimental And Numerical Analysis Of Laminar And Transitional Flow Through Annular Corrugated Pipes, Joseph Russell Sargent

Theses and Dissertations

This dissertation presents studies on pressure loss through annular corrugated pipes to determine a friction factor coefficient using nitrogen. Ten different corrugated pipes’ geometries were evaluated via testing and experimentation. The ratio of corrugation height to inner diameter varied from 0.233 to 0.333 and the ratio of corrugation pitch to inner diameter varied from 0.181 to 0.446. Nitrogen flow rates between 0.25 to 94.4 standard liters per minute were used, resulting in Reynolds numbers, based on the corrugated pipe inner diameter, from 100 to 23,000. The experimental set-up was validated using smooth-pipe pressure loss measurements and the derived friction factor …

Numerical Simulation And Optimization Of Fin Configurations For Enhanced Heat Sink Performance In Aluminum And Copper Materials, Rimpy Singh

Mechanical and Aerospace Engineering Theses - Archive

The constant evolution of data centers and high-power electronic systems has raised critical challenges in heat dissipation and thermal management. Single-phase immersion cooling, where electronic components are submerged in a thermally conductive but non-electrically conductive liquid (dielectric liquid), offers improved heat dissipation capabilities and emerges as a promising alternative to traditional air-cooling methods, which often fail to meet the thermal demands of densely packed, high-power systems. This study investigates and compares the thermal performance of aluminum and copper heat sinks with fin thicknesses of 0.33 mm and 0.54 mm, respectively, using finite element analysis based on computational fluid dynamics (CFD) …

Materials Testing For Large Format 3d Printing, William Jenkins

Williams Honors College, Honors Research Projects

An ABS Carbon Fiber blend was printed into single walled hexagons at a variety of settings on a Cincinnati BAAM large format 3D printer. These hexagons were then cut down into sheets and had tensile and flexural test samples cut out of them, in order for materials testing to be performed. Tensile strength, tensile strain, young’s modulus, flexural strength, deflection and elastic modulus were all determined. A desktop CNC machine and a planer were purchased for the manufacturing of these samples, and an efficient cutting procedure was designed and optimized. After all data collection concluded, this data was thoroughly analyzed, …

Short Strand Carbon Fiber Reinforced Polylactic Acid Filament For Additive Manufacturing, Dale Chenoweth, Lukas Seggi, Luke Phillips

Williams Honors College, Honors Research Projects

In this design project, the additive manufacturing filament of short strand carbon fiber (SSCF) reinforced polylactic acid (PLA) composite was developed. The micro-size, precision cut SSCFs were mixed with the PLA pellets through a melting homogenization process. Through this process the composite material block is cut and divided into pieces for ease of pelletizing. The material block pieces are then pelletized to be fed through the single screw extruder to develop the SSCF-PLA composite filament. The SSCF-PLA filaments were manufactured with a varying amount of SSCF ranging from 0.5% to 10% of the material block's weight. Development of a 1% …

Comprehensive Review And Development Of A High-Pressure Hydraulic Impedance Tube For Vibroacoustic Attenuator Characterization, Matthew D. Beals

Dissertations, Master's Theses and Master's Reports

This research establishes a versatile test bench for characterizing hydraulic vibroacoustic attenuators. The primary evaluation metric is the transfer matrix, determined experimentally, with an emphasis on key properties such as transmission loss. To ensure accuracy and broad applicability, the methodology is based on industry-standard techniques for determining the transfer matrix. A comprehensive literature review consolidates existing approaches for hydraulic attenuator characterization. The test bench features a hydraulic impedance tube equipped with eight dynamic pressure transducer (DPT) taps strategically positioned before and after the sample interface. This setup accommodates arbitrary samples terminated with standard hydraulic fittings. Using ASTM E2611, the transfer …

Disc Golf Throwing Robot, Nevada S. Schultz, Sydney M. Lewis, Erick Edmundo Daza, Rachel Alysse Greenberg, Peter M. Kean

Mechanical Engineering

Disc golf companies need better methods to test disc flight. The scope of this project is to create a disc throwing robot that can throw a disc golf driver 450-500 feet, with control over the speed, spin, and release angle. Research shows that multiple disc-throwing products exist; however, none meet the full requirements of this project. The Cal Poly senior project design team created a proof-of-concept machine. This prototype started as a two-wheel mechanism. Eventually, a third wheel was added, allowing for complete control over disc spin. The three-wheel prototype reached 62 mph when perfectly calibrated. The prototype is accurate, …

Design And Manufacture Of An Aerodynamic Body That Meets Scaling Law Requirements And Survives Severe G-Load Environment For Free-Flight Testing, Anthony R. Gonzalez

Graduate Theses, Dissertations, and Problem Reports (ETD)

Design and Manufacture of an Aerodynamic Body that Meets Scaling Law Requirements and Survives Severe G-load Environment for Free-Flight Testing

Anthony Gonzalez

Developing scale models to test functionality and ascertain aerodynamic properties is critical before manufacturing full-size products. Through dimensional analysis and similitude, engineers create scale models to test any parameter of interest. This research aims to design a scale model of an aerodynamic body for repeated free-flight testing. The Froude number is the dominant scale model law used to determine the geometric, mass, and inertia scaling laws. A critical requirement for this research is that the model should be …

Dynamic Analysis, Characterization, And Design Of Rigid-Flex Pcb Robotics, John Bell

All Dissertations

The era of space exploration is driven by and fuels large advances in technological progress.
Over the last decade, engineering practices for spacecraft, space structures, robotics, software and
hardware, manufacturing techniques, and the implementation of new and novel materials has been
revolutionized. Space exploration pushes the envelope in terms of technological capabilities and
robotic systems (rovers) become lighter, smaller, and more capable of sustaining damage. This
dissertation aids in the advancement of design knowledge for a class of rovers characterized by
their chassis architecture: rigid-flex printed circuit board (PCB) robotics. These rovers leverage
the printed circuit cards as the structural …

Foundations For Finite-State Modelling Of A Two-Dimensional Airfoil That Reverses Direction, Jake Michael Oscar Welsh

McKelvey School of Engineering Graduate Student Theses & Dissertations

Current 3-D finite-state wake models are incapable of simulating a maneuver in which the sign of the free-stream velocity changes direction and the rotor enters its own wake -- as might occur in the case of a helicopter which ascends and then descends. It is the purpose of this work to create a 2-D finite-state wake model which is capable of handling changes in free-stream direction as a precursor to development of a 3-D model that can do the same.

The 2-D finite-state model used for reentry modifications is an existing model created by Peters, Johnson, and Karunamoorthy. By the …

Jcati Carbon Fiber Recycler: Oven Enclosure, Margarita Romero

All Undergraduate Projects

Central Washington University partners with Boeing and is funded by the Joint Center of Aerospace Technology Innovation (JCATI) to develop a mechanism that takes carbon fiber wing trimmings from Boeing that are resin coated and recycles carbon fiber. This is done by crushing the wing trimmings and then putting it into a 500°C oven to melt off the resin. This project focuses on the enclosure for the oven and making sure precautions are met such as having the outside surface be less than 45c through heat transfer analysis, argon fills enclosure in 13 minutes through fluid dynamics analysis, and 99% …

Nitinol Robotic Arm, Brandon Cousino, Connor Sweatt

Thinking Matters Symposium

The goal of our project is to create a remotely controlled robotic arm using a nickel-titanium alloy (Nitinol) that exhibits “shape memory” tendencies and a 9-lumen tube. The arm must be able to move in all for directions (forward, left, right, backwards) with the control of a joystick and return to an upright position upon halting user input (thus requiring a two-way shape memory ability). The final product must operate without any unwanted twisting of the arm, crosstalk between the different nitinol wires due to heating, and be easily manufacturable. Easy replacement of the arm from the main mechanism is …

Development Of Triangular And Tetrahedral Finite Elements For Solutions To Thermoelastic Instabilities Using Hotspotter, Cortney Samuel Leneave

Electronic Theses and Dissertations

The objective of the work presented in this thesis is to develop first-order triangular and tetrahedral elements for solutions to Thermoelastic Instabilities (TEI) regarding sliding friction systems in Hotspotter.

Hotspotter software uses a finite element method and an eigenvalue method and is an important tool because currently no other commercial software exists which solves the TEI problem for critical velocities and wave numbers of a system. Hotspotter currently uses quadrilateral and hexahedral elements for two and three dimensional analysis, respectively. Typically, tri and tet elements are used in industry when doing static and dynamic stress analysis. Therefore, the Hotspotter user …

Safran Seat Attachment System, Craig John Kimball, Tyler Bragg, Lynette Cox

Mechanical Engineering

This final design review (FDR) document outlines the senior design project being carried out by a team of mechanical engineering undergraduate students attending California Polytechnic State University, San Luis Obispo for Safran Seats in Santa Maria, CA. The project originally was to design, build, and test a universal attachment to secure a widebody business class seat to seven aircraft models with different seat track geometry. The goal was to design, document, and create a finished product that fits design, weight, and manufacturing requirements, as well as passes static 9G FWD testing. Structural analysis, manufacturing analysis, FEA, and CAD assemblies will …

Drone Payload Storage & Release System (Dpsrs), Joseph E. Key

All Undergraduate Projects

The retail giant Amazon has become a household name synonymous with nearly instantaneous online shopping. What previously took weeks to deliver at exorbitant shipping fees can now arrive at your doorstep within two days—and all for free. This huge buyer incentive has skyrocketed the demand for online shopping, making Amazon the most valuable brand in the world. To meet this demand, Amazon and its distributors have proposed using drones to make deliveries. However, due to issues with cost and complexity, this has not yet materialized. As such, this project’s objective was to create a cheap and lightweight package-delivery system that …

Design Of Banner Tow Mechanism For Bush Plane, Kyle Ciarrone, Ivan Martin, Rishabh Gadi, Tyler Brandt

Williams Honors College, Honors Research Projects

The 2019-2020 AIAA DBF objective was to design, build, and test a banner-towing bush plane that carries wooden passengers and luggage. Senior members on the team undertook the creation of the banner tow mechanism subsystem as their senior design project on behalf of the design team due to the challenge of its mechanical design and the aerodynamic considerations regarding its placement and enclosure aboard the aircraft. The competition as well as access to campus resources were canceled due to COVID-19, so full testing and integration of the mechanism was not achieved. However, the engineering design process was experienced from the …

Flow Behavior In Radial Rotating Detonation Engines, Scott A. Boller

Theses and Dissertations

Recent progress has been made in demonstrating Radial Rotating Detonation Engine (RRDE) technology for use in a compact Auxiliary Power Unit with a rapid response time. Investigation of RRDEs also suggests an increase in stable operating range, which is hypothesized to be due to the additional degree of freedom in the radial direction which the detonation wave can propagate. This investigation seeks to determine if the detonation wave is in fact changing its radial location. High speed photography was used to capture chemiluminescence of the detonation wave within the channel to examine its radial location, which was found to vary …

Enhanced Surface Integrity With Thermally Stable Residual Stress Fields And Nanostructures In Cryogenic Processing Of Titanium Alloy Ti-6al-4v, James R. Caudill

Theses and Dissertations--Mechanical and Aerospace Engineering

Burnishing is a chipless finishing process used to improve surface integrity by severe plastic deformation (SPD) of surface asperities. As surface integrity in large measure defines the functional performance and fatigue life of aerospace alloys, burnishing is thus a means of increasing the fatigue life of critical components, such as turbine and compressor blades in gas turbine engines. Therefore, the primary objective of this dissertation is to characterize the burnishing-induced surface integrity of Ti-6Al-4V alloy in terms of the implemented processing parameters. As the impact of cooling mechanisms on surface integrity from SPD processing is largely unexplored, a particular emphasis …

Comparison Of Flow Field In The Proximity Of A Single Planar & Wrap-Around Fin, Nayhel Sharma, Palak Saini, Hrishabh Chaudhary, Gurteg Nagi, Rakesh Kumar Dr.

International Journal of Aviation, Aeronautics, and Aerospace

Abstract

This paper analyses the results of the computational analysis between a single planar and a wrap-around fin mounted on a semi-cylindrical body. A free-stream Computational Fluid Dynamics (CFD) model was simulated for both cases in the Mach 0.4-3.0M range at 0°Angle of attack, in which, the behavior of flow around the fin was investigated using a turbulence model of higher order discretization. The post-processing shows all the possible views of the flow dynamics around the fins, as well as the missile body. The aerodynamic drag and the rolling moment characteristics of the planar and the wrap-around fin have been …