Other Aerospace Engineering Commons^™

Modeling And Testing Chain Trencher Excavator And Cone Penetrometer Robotic Prospecting Systems For Lunar In-Situ Resource Utilization, Marcello C. Guadagno

Dissertations, Master's Theses and Master's Reports

The Artemis Missions aim to establish a sustained human presence on the Moon, requiring In-Situ Resource Utilization (ISRU) of water-ice deposits in permanently shadowed regions. Two critical capabilities must be developed to enable ISRU at scale: prospecting instruments that can characterize the spatial distribution and geotechnical properties of icy regolith in situ, and excavation systems that can extract hardened icy regolith efficiently. This dissertation addresses both needs through the development and testing of a Percussive Heated Cone Penetrometer (PHCP) for geotechnical prospecting and a chain trencher excavator for icy regolith mining.

The PHCP was developed across eight design iterations and …

Investigation Of The Impact Of The Shape Of The Wings On Formula E Racing Car Performance: Enhancements For Optimal Aerodynamics, Ednie Marthe Adlaikah Jozil

Honors Undergraduate Theses

The aerodynamic performance of a Formula E chassis significantly dictates its overall race efficiency, directly impacting crucial parameters such as battery range and thermal management. This thesis investigates the external aerodynamics of the baseline Gen 2 Formula E car and evaluates the performance gains of two novel aerodynamic packages: a "Fully Modified" configuration and a "Flat Rear Wing" design. Computational Fluid Dynamics (CFD) simulations were conducted to analyze drag coefficients (Cd), downforce generation, and vehicle wake structures at race-relevant free-stream velocities (e.g., 37 m/s and 89 m/s). To ensure numerical robustness, the computational setup was validated using a smooth sphere …

Active Measurement Of A Micron-Order Gap Under High-Speed And High-Temperature Conditions, Andrew Becker

Doctoral Dissertations and Master's Theses

The hypersonic regime poses numerous challenges that researchers face in the development of hypersonic flight vehicles. Due to their excellent thermomechanical properties, ultra-high-temperature ceramics (UHTCs) have risen as a promising solution to act as a protective barrier between the harsh environment and surface materials of these flight bodies. The mechanical operation of a portable hypersonic simulation device was developed in-house and tested at Argonne National Laboratories (ANL) to gather in-situ material response of prospective UHTC samples when exposed to a hypersonic regime. An edge detection-based algorithm was developed and used in LabVIEW to monitor the health and operation of the …

Reconfigurable Python Autopilot Software For Rc Aircraft, Kate Doiron

Honors Theses

No abstract provided.

Experimental And Numerical Analysis Of Laminar And Transitional Flow Through Annular Corrugated Pipes, Joseph Russell Sargent

Theses and Dissertations

This dissertation presents studies on pressure loss through annular corrugated pipes to determine a friction factor coefficient using nitrogen. Ten different corrugated pipes’ geometries were evaluated via testing and experimentation. The ratio of corrugation height to inner diameter varied from 0.233 to 0.333 and the ratio of corrugation pitch to inner diameter varied from 0.181 to 0.446. Nitrogen flow rates between 0.25 to 94.4 standard liters per minute were used, resulting in Reynolds numbers, based on the corrugated pipe inner diameter, from 100 to 23,000. The experimental set-up was validated using smooth-pipe pressure loss measurements and the derived friction factor …

Design And Manufacture Of An Aerodynamic Body That Meets Scaling Law Requirements And Survives Severe G-Load Environment For Free-Flight Testing, Anthony R. Gonzalez

Graduate Theses, Dissertations, and Problem Reports (ETD)

Design and Manufacture of an Aerodynamic Body that Meets Scaling Law Requirements and Survives Severe G-load Environment for Free-Flight Testing

Anthony Gonzalez

Developing scale models to test functionality and ascertain aerodynamic properties is critical before manufacturing full-size products. Through dimensional analysis and similitude, engineers create scale models to test any parameter of interest. This research aims to design a scale model of an aerodynamic body for repeated free-flight testing. The Froude number is the dominant scale model law used to determine the geometric, mass, and inertia scaling laws. A critical requirement for this research is that the model should be …

Foundations For Finite-State Modelling Of A Two-Dimensional Airfoil That Reverses Direction, Jake Michael Oscar Welsh

McKelvey School of Engineering Graduate Student Theses & Dissertations

Current 3-D finite-state wake models are incapable of simulating a maneuver in which the sign of the free-stream velocity changes direction and the rotor enters its own wake -- as might occur in the case of a helicopter which ascends and then descends. It is the purpose of this work to create a 2-D finite-state wake model which is capable of handling changes in free-stream direction as a precursor to development of a 3-D model that can do the same.

The 2-D finite-state model used for reentry modifications is an existing model created by Peters, Johnson, and Karunamoorthy. By the …

Jcati Carbon Fiber Recycler: Oven Enclosure, Margarita Romero

All Undergraduate Projects

Central Washington University partners with Boeing and is funded by the Joint Center of Aerospace Technology Innovation (JCATI) to develop a mechanism that takes carbon fiber wing trimmings from Boeing that are resin coated and recycles carbon fiber. This is done by crushing the wing trimmings and then putting it into a 500°C oven to melt off the resin. This project focuses on the enclosure for the oven and making sure precautions are met such as having the outside surface be less than 45c through heat transfer analysis, argon fills enclosure in 13 minutes through fluid dynamics analysis, and 99% …

Drone Payload Storage & Release System (Dpsrs), Joseph E. Key

All Undergraduate Projects

The retail giant Amazon has become a household name synonymous with nearly instantaneous online shopping. What previously took weeks to deliver at exorbitant shipping fees can now arrive at your doorstep within two days—and all for free. This huge buyer incentive has skyrocketed the demand for online shopping, making Amazon the most valuable brand in the world. To meet this demand, Amazon and its distributors have proposed using drones to make deliveries. However, due to issues with cost and complexity, this has not yet materialized. As such, this project’s objective was to create a cheap and lightweight package-delivery system that …

Design Of Banner Tow Mechanism For Bush Plane, Kyle Ciarrone, Ivan Martin, Rishabh Gadi, Tyler Brandt

Williams Honors College, Honors Research Projects

The 2019-2020 AIAA DBF objective was to design, build, and test a banner-towing bush plane that carries wooden passengers and luggage. Senior members on the team undertook the creation of the banner tow mechanism subsystem as their senior design project on behalf of the design team due to the challenge of its mechanical design and the aerodynamic considerations regarding its placement and enclosure aboard the aircraft. The competition as well as access to campus resources were canceled due to COVID-19, so full testing and integration of the mechanism was not achieved. However, the engineering design process was experienced from the …

The Effect Of Biocomposite Material In A Composite Structure Under Compression Loading, Benjamin Andrew Sweeney

Master's Theses

While composite structures exhibit exceptional strength and weight saving possibilities for engineering applications, sometimes their overall cost and/or material performance can limit their usage when compared to conventional structural materials. Meanwhile ‘biocomposites’, composite structures consisting of natural fibers (i.e. bamboo fibers), display higher cost efficiency and unique structural benefits such as ‘sustainability’. This analysis will determine if the integration of these two different types of composites are beneficial to the overall structure. Specifically, the structure will consist of a one internal bamboo veneer biocomposite ply; and two external carbon fiber weave composite plies surrounding the bamboo biocomposite. To acquire results …