Aerodynamics and Fluid Mechanics Commons^™

Experimentation And Simulation Of Pulsed Eddy Current Thermography Of Subsurface Aircraft Corrosive Defects, Johnathan Hernandez

Electronic Theses and Dissertations, 2020-2023

During the life cycle of aircraft, external structures are under constant attack from environmental degradation in the form of corrosion. Corrosive defects consist of multiple types of surface and subsurface damage that are often undetectable due to surface coatings or insulation leading to loss in structural integrity. Non-destructive techniques for corrosion detection typically require the removal of paint. Detection of corrosion under insulation (CUI) is highly valuable for cost and time effectiveness. Although techniques have been developed for detection of CUI, not many of these satisfy the criteria for portability and hangar operation. To address this, multiple techniques were investigated …

Evaluation Of Convective Heat Transfer Numerical Methods On Rough Surfaces From Additive Manufacturing, Jose Urcia

Electronic Theses and Dissertations, 2020-2023

The high versatility of additive manufacturing has led to an increase in use in a number of different fields. Surface roughness then comes as a natural consequence of additive manufacturing which interferes with a smooth wall assumption such as those found in gas turbine blades. The Discrete Element Roughness Method (DERM) has been used to improve convective heat transfer predictions on surface roughness. This work aims to validate the core momentum and heat transfer correlation of DERM through an evaluation of Computational fluid dynamics (CFD)-based solution of the flow around individual roughness elements with the goal of improving the correlations. …

Flame Stabilization Of A Premixed Jet In Vitiated Coflow, Tyler Owens

Theses and Dissertations--Mechanical and Aerospace Engineering

Premixed staged combustion in gas turbine engines can reduce emissions by lowering peak flame temperatures but can also lead to different stability characteristics when compared to traditional combustors. High pressure ratio and subsequently high temperatures can lead to conditions suitable for both autoignition and premixed flame propagation in an environment where spatial fuel/air variations are present.

An experimental facility which issues a premixed jet into a coflowing vitiated mixture was studied to examine the stability behavior, resulting in a lifted flame. The effective ignition delay observed flame was much greater than homogeneous ignition delay calculations for the same conditions. It …

Development Of Universal Solver For High Enthalpy Flows Through Ablative Materials, Umran Duzel

Theses and Dissertations--Mechanical and Aerospace Engineering

Atmospheric entry occurs at very high speeds which produces high temperature around the vehicle. Entry vehicles are thus equipped with Thermal Protection Systems which are usually made of ablative materials. This dissertation presents a new solver that models the atmospheric entry environment and the thermal protection systems. In this approach, both the external flow and the porous heat shield are solved using the same computational domain. The new solver uses the Volume Averaged Navier-Stokes Equations adapted for hypersonic non-equilibrium flow, and is thus valid for both domains. The code is verified using analytical problems, set of benchmarks and also a …

Efforts In Numerical Modeling Of Undulating Propulsion, George Loubimov

Electronic Theses and Dissertations, 2020-2023

Naval propulsion is a critical component for every vessel, and it is the subject of this thesis, specifically bio-inspired propulsion. Numerical modeling is used as a tool to understand the relationship between mechanical undulation and the hydrodynamic response. Through three stages, the research presented here examines and refines tools for understanding fundamentals of undulating propulsion. Those three objectives are: to verify and validate the proposed numerical models against existing experiments, establishing a baseline of fidelity; to examine the causal linkage between fluid-boundary interactions and undulating propulsion; and to create a moment based method for characterizing generalized undulating propulsive mechanisms. First, …

Comparison Of Reynolds-Averaged Navier-Stokes Turbulence Models For Simulating Boundary Layers In Hypersonic Flows, Jorge-Valentino Kurose Bretzke

Masters Theses

“This study describes the use of Computational Fluid Dynamics (CFD) codes to simulate hypersonic boundary layers using several different turbulent closure models and comparing Reynolds-Averaged Navier-Stokes (RANS) simulations against Direct Numerical Simulations (DNS) of similar test cases. The test cases in this study consist of a flat plate in a Mach 8 freestream with a zero pressure gradient and wall recovery ratio of 0.48, as well as a Mach 8 axisymmetric nozzle also with a cold wall. The RANS models used in this study are the Spalart-Allmaras model, Baldwin-Lomax model, Menter K-Omega Baseline and Menter K-Omega Shear Stress Transport models. …

Effect Of Turbulence Model Closure Coefficient Uncertainty On Scramjet Flow Field Analysis, Martin Albert Di Stefano

Doctoral Dissertations

“The numerical modeling of supersonic combustion ramjet (scramjet) engine flow paths plays an important role in the design of hypersonic air-breathing propulsion systems. Due to the complexity of the flow field physics and limited experimental data, numerical models possess uncertainties which should be addressed to improve the prediction accuracy of the simulations. In this study, the effect of turbulence model closure coefficient uncertainty on the Reynolds-averaged Navier-Stokes solution of a scramjet isolator and scramjet strut fuel injector flow field is investigated with an uncertainty quantification and sensitivity analysis study for commonly used turbulence models. Turbulence models considered in this work …

Toward Adjoint-Based Aeroacoustic Optimization For Propeller And Rotorcraft Applications, Ramiz Ö. Içke, Oktay Baysal, Andy Moy, Leonard V. Lopes, Beckett Zhou, Boris Diskin

Mechanical & Aerospace Engineering Faculty Publications

The goal of the present project is to build a multidisciplinary, rapid, robust, and accurate computational tool to optimize wing-mounted propeller designs. The full Farassat’s formulation F1A for aeroacoustic analysis is implemented in the open-source software SU2. This extension enables the prediction of far-field noise generated by moving sources. The formulation is verified, for a stationary and rotating sphere in a wind tunnel and for a tiltrotor in forward flight, by comparing the acoustic predictions of SU2 with the predictions computed by NASA’s aeroacoustics code ANOPP2. The algorithmic differentiation capability of SU2 provides discretely consistent, adjoint-based sensitivity analysis for this …

Rocket Motor Nozzle, Corey Hillegass

Williams Honors College, Honors Research Projects

For this honors research and senior design project, the authors will research, analyze, and manufacture a rocket motor nozzle for the Akronauts rocket design team. This research and design project will improve how the rocket design team will decide and manufacture nozzles going forward. The impact of this improvement allows the rocket design team to take steps toward being self-sustaining by manufacturing student designed parts as opposed to commercially bought parts. This will not only be successful in increasing student impact on future designs, but also provides a technical challenge for the authors and will present as an impressive feat …

Design, Construction And Testing Of A 3-Component Force Balance For Educational Wind Tunnels In Undergraduate Aerodynamics, Milan Tomin, Marco Scipioni, Benjamin Gatti

Journal of Aviation/Aerospace Education & Research

This article is focused on providing detailed instructions on how to build and use a force balance for educational wind tunnels. The article’s objective is to encourage undergraduate students in underfunded programs to engage in the field of aerodynamics. The discussed force balance represents an affordable device that only requires basic components like Arduino board, a servo motor, and acrylic and aluminum as construction materials. A simple data collection example is included at the end of the article showing that this simple force balance can collect meaningful data about lift, drag, and moment coefficient of a tested airfoil.

Supersonic Propulsion: Inlet Shock Wave/Boundary Layer Interaction In A Diffuser, Lucas Fulop, Ian Henry, Jordan Ruffner, Anthony Mcmullen

Williams Honors College, Honors Research Projects

Using a finite-volume approach and ANSYS/FLUENT, supersonic flow over a 2-D ramp of varying angles is modeled. The computational results from this model will be used to further explore the design of supersonic diffusers used on military aircraft. Using grid capturing features and inflation layers, shockwave and boundary layer interactions will be observed as well as wave-associated pressure changes in supersonic turbulent flow. The Spalart-Allmaras single-equation model of turbulent flow will be used in all simulations to more accurately represent the phenomena that occur in such high-speed environments. The size of upstream zones and recirculation zones will be obtained through …

Study Of Non-Ideal Effects On Shock Wave Propagation, Cory Kinney

Electronic Theses and Dissertations, 2020-2023

Shock tube experiments provide insightful data on combustion, emissions, and ablation characterization for a wide variety of defense and energy sector research topics. Accurate characterization of shock tube facilities is essential to verifying the accuracy of research data. Non-ideal effects, such as boundary layer growth, introduce uncertainty into pressure and temperature conditions, the primary independent variables of interest for shock tube research results. The effect of boundary layer growth on shock tube experiments was investigated by conducting simulations for University of Central Florida's two geometrically different shock tube using StanShock, a quasi-one-dimensional, reacting, compressible flow solver. The characteristic quantities considered …

Low-Cost Skewed Redundant Imu Configuration For State-Space Recovery In A Saturated Environment, Levi S. Hubbard

Graduate Theses, Dissertations, and Problem Reports (ETD)

Low-cost sensors for state space determination can be used successfully for ground vehicles, robots, unmanned aerial vehicles, and Internet-of-Things applications. When a high fidelity Inertial Measurement Unit (IMU) cannot be obtained for state space determination, low-cost sensors can be used to satisfactory standards, despite their limitations in capabilities, by using various implementation techniques. The research group was experimentally investigating state space information of an unstable flying vehicle for motion simulation validation. The high fidelity motion capture system would intermittently lose track of the flight vehicle which lost critical flight data.

The goal was to determine the potential of low-cost off-the-shelf …

Thermal / Structural Analysis Of The Hb 650 Thermal Shield, Gerald J. Smith

Graduate Research Theses & Dissertations

Fermilab’s PIP-II project’s superconducting linear accelerator (Linac) will drive the next generation of particle accelerators through a revolution in beam intensity. Key to beam intensification are the high efficiencies of niobium-tin superconducting radiofrequency (SRF) cavities operating at cryogenic temperatures near 5 Kelvin. A multifaceted approach is employed to achieve and maintain the extreme temperature. Vacuum provides the first barrier to thermal convection. Physical thermal intercept zones further isolate the exterior shell vacuum vessel at 300 Kelvin from the supercooled beamline. The first thermal intercept lies just inside the exterior vacuum vessel forming the 40 Kelvin zone. This 40K thermal shield …

Magnetic Control Of Transport Of Particles And Droplets In Low Reynolds Number Shear Flows, Jie Zhang

Doctoral Dissertations

“Magnetic particles and droplets have been used in a wide range applications including biomedicine, biological analysis and chemical reaction. The manipulation of magnetic microparticles or microdroplets in microscale fluid environments is one of the most critical processes in the systems and platforms based on microfluidic technology. The conventional methods are based on magnetic forces to manipulate magnetic particles or droplets in a viscous fluid.

In contrast to conventional magnetic separation method, several recent experimental and theoretical studies have demonstrated a different way to manipulate magnetic non-spherical particles by using a uniform magnetic field in the microchannel. However, the fundamental mechanism …

Identify Aerodynamic Derivatives Of The Airplane Attitude Channel Using A Spiking Neural Network, Nguyen Quang Vinh, Nguyen Duc Thanh, Hoang Minh Dac, Truong Dang Khoa

International Journal of Aviation, Aeronautics, and Aerospace

The paper proposes a method for identifying aerodynamic coefficient derivatives of aircraft attitude channel using spiking neural network (SNN) and Gauss-Newton algorithm based on data obtained from actual flights. Using SNN combination with Gauss-Newton iterative calculation algorithm allows the identification of aerodynamic coefficient derivatives in a nonlinear model for aerodynamic parameters with higher accuracy and faster calculation time. The paper proposes an algorithm to train the SNN multi-layer network by Normalized Spiking Error Back Propagation (NSEBP), in which, in the forward propagation period, the time of output spikes is calculating by solving quadratic equations instead of detection by traditional methods. …

Performance Characteristics Design Of Pulsed Plasma Thrusters For Drag Counter-Reacting, Dr. Sam Dakka

International Journal of Aviation, Aeronautics, and Aerospace

Determining the performance characteristics of off the shelf pulsed plasma thrusters to enhance the life time of low earth orbiting platforms was investigated theoretically. Pulsed plasma thruster analysis was accomplished through development of correlations from historical data that distinguished between breech fed propellant to side fed propellant designs. Based on semi-empirical equations the power required by the thruster to counter react the drag was estimated and mapped for 1U to 27U CubeSat configurations for altitude ranging between 200km to 600km. It appears that the power required is dependent on the feeding delivery system design. For side fed designs the power …

The Detrimental Effect Of Rainfall On Performance And Stability Characteristics Of Aircrafts-A Comprehensive Review, Praneeth Hr Mr, Amit Kumar Thakur Dr

International Journal of Aviation, Aeronautics, and Aerospace

The rapidly growing global market demands faster transit of human beings and goods even in unfavorable weather conditions of rainfall. The paper gives an overview of rain research methodologies, mathematical models to track raindrops in the flow field. The paper depicts the havoc rainfall causes on performance characteristics for various phases of flight in terms of evaluation of C_L and C_D and dynamic performance parameters such as short period mode. The knowledge obtained by this review paper could help designers to modify the design of aircraft such that it has better performance, stability, and control characteristics for all …

Experimental And Computational Evaluation Of Five Hole Five Probe Flow Analyzer For Subsonic Wind Calibration, Akhila Rupesh Ms, J V Muruga Lal Jeyan Dr

International Journal of Aviation, Aeronautics, and Aerospace

It is very essential to predict the flow and its related parameters to understand real life fluid flow. The real-life fluid problems are studied with wind tunnels which gives very efficient results in practice. But in the case of wind tunnel studies flow angularities plays crucial role. Flow angularity determination includes measurement of static pressure, dynamic pressure and inflow angles. Flow prediction even hold a very strong hand in design process. Designing and testing being the foundation of any process industry, flow measurements and its related parameters have to be well evaluated. In such cases, wind tunnels play important role …

Unsteady Aerodynamic Analysis Of Wind Harvesting Aircraft, Judd Mehr, Eduardo Alvarez, Andrew Ning

Faculty Publications

Airborne Wind Energy (AWE) technology aspires to provide increased options for wind energy harvesting. This includes increased feasibility for temporary and remote installations, as well as the ability to operate at wind speeds both lower and higher than traditional turbines. Additionally, the hope is to be able to produce these extensions of wind energy technology at a lower cost than conventional technologies. As AWE technology is still in its infancy, however, there is very little published information concerning the aerodynamic details of the technology. We have created a set of aerodynamic analysis tools which we apply to wind harvesting aircraft, …

Characterizing Premixed Syngas Combustion In Micro-Channels, Sunita Pokharel

Graduate Theses, Dissertations, and Problem Reports (ETD)

Increasing demands in the next-generation portable power-generation devices such as unmanned aerial vehicles (UAV), microsatellite thrusters, micro-chemical reactors and sensors calls for fuels with high specific energy and low emissions to meet the current demand of green energy. Fuel-lean synthesis gas (syngas) meets both these requirements exhibiting a promising route to a clean and green environment. Thus, it is of critical importance to characterize syngas combustion and understand its properties in the micro-combustion industry. In addition to complicated flame dynamics in microscale systems, varying the syngas-fuel mixture composition as well as the boundary conditions and geometry of a combustor significantly …

Aeroelasticity Of Composite Plate Wings Using Hsdt And Higher-Order Fem, Justin A. Haught

Graduate Theses, Dissertations, and Problem Reports (ETD)

The aeroelasticity of composite wings is becoming an increasingly researched topic in aircraft design, as designers continue to replace aluminum alloy components with those made of composite materials because of their favorable strength-to-weight ratio, fatigue characteristics, and corrosion resistance. Additionally, the bending-torsion coupling exhibited by composite laminates readily allow for the aeroelastic optimization of an aerodynamic structure through the process of aeroelastic tailoring. Wings made of composites materials, however, are more vulnerable to shear deformation.

The objective of the present research is to study the divergence and flutter characteristics of composite plate wings using a higher-order shear deformation theory (HSDT) …